The right choice of engine oil will prevent wear and provide normal work car Engine. In this article we will tell what oil is pouring into engine Kia. Rio. In addition, you will learn how to determine the frequency of work on replacing lubricating fluid and oil filter and how to perform these works yourself.
[Hide]
On the reconnaissance periodicity
Operating Instructions, relevant for cars 2010, 2011, 2012, 2013, 2014, 2015, 2016 release, recommends changing the oil every 15 thousand km of run. However, in practice, this recommendation is suitable only for the operation of the machine in optimal conditions, which is not always fulfilled in Russia and the CIS countries.
The streets of cities are overloaded, the cars are moving at low speeds, idle in traffic jams. In such conditions, motors work for a long time on idlingAnd this is not at all reflected on the speedometer readings. Also, the change in the replacement is significantly affected by the fuel quality at refueling, which does not always correspond to the necessary parameters. therefore optimal mileage Car between replacements motor lubricant There will be a mileage of about 10 thousand km, and during operation in difficult conditions it is reduced to 7-8 thousand km.
Some experts are advised when determining the moment when lubricating fluid should be changed, to use indications on-board computer. With it, you can easily find out the average speed of the machine. If this indicator is more than 50 km / h, it is safe to operate the power unit to a mileage of equal to 15 thousand km. If it is located in the area of \u200b\u200b30 km / h, the mileage is reduced to 10 thousand km.
Check out the video about the replacement of oil from user Mikhail Knyazev.
Possible causes of oil consumption
Such a problem occurs even from very new cars, but most often this "disease" accompanies cars with significant mileage.
Increased oil consumption can be caused:
- the presence of leaks in the power unit;
- cylinder wear, pistons, rings;
- an increased gap between the guide bushings and the valve rods;
Typical causes of such problems:
- incorrect operation of the machine;
- movement in dust conditions;
- work for a long time at idle;
- frequent motion with high speeds.
Which oil is better to choose
The service life of any automotive motor depends on the quality of the lubricant used.It is difficult to independently determine the right choice, since trading platforms are filled with a large number of engine oils different manufacturers and different quality. Browse the manufacturer's recommendations of the car, listen to the advice of specialists and only then determine which oil to fill into the engine Kia Rio.
Motor oil for Kia Rio Lubrication Quartz. Oil Helix. Ultra oil Helix
Motor lubricating fluids are distinguished by season.
- winter lubricants;
- summer oils;
- all-season motor oils.
These products are based on such materials:
- mineral oils;
- semi-synthetic;
- synthetic.
The manufacturer recommends using synthetic oils for Kia Rio. In such a product, various additives are added, which improve wettability, have anticorrosive properties, increase the resistance to wear. Recommended viscosity manufacturer motor fluid - 5W-20, 5W-30. Also, all-season oils with a viscosity of 10W-40 acquired great popularity.
If the owner decides to change the lubricant on his own, he should take into account the existing features of the power units of these cars.
- Shell Helix. ULTRA;
- Total Quartz;
- Divinol;
- Zic XQ Ls;
From the list of the most suitable option There will be shell Helix Ultra.. It has a complete list of the desired additives that provide a long period of operation of the machine. Total Quartz also has a good set of additives. The smallest consumption has lubricant Divinol. ZiC XQ LS liquid also can safely apply for this machine. In addition to listed lubricants, Mobile, Castrol, some others use products.
Choose filter
Oil filter
Replacing motor lubrication in machine Kia. Rio implies a mandatory replacement of the oil filter. For individual modifications of engines, oil filters with different catalog numbers are used. For power aggregate with an engine volume equal to 1.4 liters filter has catalogue number 2630002503, and if the volume is 1.6 liters, the number is already 2630035504. Its cost can begin from 200 rubles, it depends on the manufacturer of the spare part and the markup of the trading network.
Level control and required volume
The amount of liquid for engine lubrication depends on the type of motor and its volume.
| Engine | L.S. | Year of release (end-end) | Oil volume in engine, l | Filter, L. | ||
| 1.1 CRDI | 75 | 2011 | —> | 4.80 | 0.5 | |
| 1.2i 16V. | K1.25 | 87 | 2011 | —> | 3.30 | 0.3 |
| 1.3I | Mi-Tech | 75/82 | 2000 | 2005 | 3.40 | 0.2 |
| 1.4i 16V. | G4ee. | 97 | 2005 | 2011 | 3.30 | 0.3 |
| 1.4i 16V. | Y-1.4 | 107 | 2011 | —> | 3.70(3.30) | 0.3 |
| 1.5i 16V. | 98/108 | 2000 | 2005 | 3.40 | 0.2 | |
| 1.4 CRDI | 90 | 2011 | —> | 5.30 | 0.5 | |
| 1.5 CRDI | D4FA. | 109 | 2005 | 2008 | 5.30 | 0.5 |
| 1.6i 16V. | G4ed | 112 | 2005 | 2011 | 3.30 | 0.3 |
| 1.6i 16V. | 123 | 2011 | —> | 3.30 | 0.3 | |
Before checking the oil level, it is necessary to drown the engine after the trip and wait 5-10 minutes until the liquid stalks into the crankcase.
Instructions for measuring the level and tall lubrication:
- Install the machine on a flat horizontal surface.
- Oil dipstick is in front of motor compartment, The cork of the neck is in the right part of the cylinder head cover.
- Remove the level meter, wipe the rag and put it in place again.
- Remove the dipstick. The lubrication level must be between MAX and MIN marks.
- In order to add oil, turn the base of the oil-colored neck counterclockwise and remove it.
- Oil into the engine must be pouring, controlling its level to SHUP. Before removing the level meter, wait a couple of minutes to make the oil glass into the crankcase.
Motor lubricant should be the same brand, viscosity and quality class, as well as in the bold before.
Replacing motor oil with their own hands
Replace motor lubricant on car Kia. Rio can be in two ways: this vacuum pumping A waste fluid or standard drain method of old oil. For the first case, the presence of special equipment, which via the hole for the measuring probe pumps the lubricant. Such equipment is not available in all a hundred, and in the personal garages it is absent due to high cost.
Much cheaper to replace the standard way in which through drainer Lubrication fluid clears his time. This method is considered more reliable, since most of the sediments and pollution is going to at the bottom of the pallet, where they manage to completely remove them.
Required tools and consumables
In addition to fresh oil, you will need the following:
- oil filter;
- sealing plug plug. Catalog number 21513-23001;
- empty packaging of the desired volume for collecting waste oil;
- rafting to remove spilled lubricant;
- spanner on "17" or a head of a similar size.
In some cases, it may be necessary, there will be 3 liters.
Algorithm of action
Motor oil is drained from the engine only in a preheated state. This can be done at the end of the trip or make the motor to work for about 10 minutes.
Important! Merging the oil on the hot motor, you should be careful not to get burns.
The procedure will be approximately:
- The car is installed on the overpass, lift or above the observation pit. After that, under the wheels should substitute the stops.
- Lubrication plums prevents crankcase protection, it needs to be dismantled.
- After that, the waste liquid is drained into the empty container. Before that, carefully unscrew the drain plug. The oil-thinning cap is pre-removed, it will accelerate the leakage of lubrication.
- Now the oil filter is removed and installed a new spare part.
- The drain plug is cleaned from extraneous impurities, install a new gasket on it, after which they screw on its place.
- Fill into the engine the required amount of motor lubrication, how much it is pilled previously reported. The volume of the compound mixture is controlled by measuring shchu. The lubrication level must be between MIN and MAX marks.
Such an operation does not cause special difficulties for owners. It is easily performed in the garage with their own hands.
Motor oil fill in the engine
Replacing the filter
Some difficulties can cause the oil filter surveillance service. On the heated engine, it has a high temperature, so it follows in gloves. You can not always unscrew it with your hands, you can use various devices to dismantle it. Some drivers break through the casing of the filter with a thin dummy or a bunch, and then use this tool as a lever, with which the filter turns out from its place.
Before installing the new filter, it is filled with fresh oil. It will be enough to fill 150-200 grams of lubricant, lightly rinse with oil its sealing ring. After that, the filter element is installed on its place. To seal the filter, it is sufficient to tighten it with your hands, in the future it will make it easier to dismiss the product that served your term.
The user Kia Rio FAQ shows the video replacement of oil and filter
Consequences of untimely replacement
If you do not comply with the oil replacement time, expedited wear of the motor parts. Modern oils have additives that improve their properties. Working in high temperatures, these additives gradually burn out, the lubricant characteristic is worsening. As a result, oil starvation may occur, which can cause the crankshaft liner.
The details of the turbocharging compressor, which spent their oil resource, spent greatly. Contaminated lubricant clogs oil supply channels, which can cause the shaft to join this node or other mechanisms. The old oil fluid is poorly removing the temperature from overheated parts of the motor, which also badly affects its condition.
Kia Rio 3 in 2013 was completed with two models of engines, namely gasoline G4FA by 1.4 l and G4FG at 1.6 liters.
Both worked in the park, both with mechanical and automatic species transmissions.
In 2015, on Hatchback petrol aggregate At 1.6 liters was replaced with a diesel analogue - G4FC. He had the same power in 123 hp, but it was more reliable, more durable and distinguished by greater efficiency.
2016 brought another changes for sedans. In addition to the gasolinemic, a diesel version - G4LC, and a diesel version of 1.6 liters has been replaced by a 1.6-liter diesel and a proven and reliable G4FG with gasoline food already known to us.
That is, for several years the manufacturer has installed 3 four at Kia Rio type of DVS: 2 gasoline and 2 diesel with maximum output power in 123 hp
These are reliable units that were well shown in operation, but only under the condition of timely replacement of engine oil.
When should I change the oil?
In practice, the owners of this model with experience are recommended to do this more often, every 8-10 thousand km, depending on the type of oil poured and the operating conditions of the car.
It is also important to understand where the machines are operated, in the extreme north or in the southern regions of the country, because oil changes its properties with a change in the ambient temperature.
In the summer, more viscous oil should be used to and when it is heated to operating temperatures, enveloping lubricating qualities remained.
IN winter You should use lubricant with less viscosity, as the start of the engine on summer oils It will be accompanied by large loads on the motor, special when starting when it is cold.
In order not to replace the engine oil twice a year, pay attention to the universal fluids, which are suitable for use for operation all year round. But not for all regions of the country this option is suitable.
Original synthetic oils
The manufacturer uses for engines to Kia Rio 3 the following types of oils are shown along with custom articles:
- 1845-004 5W-30 - DEMITZU ZEPRO TURING;
- 3583041 0W-20 - Demitzu Zepro Touring;
- 0510000441/0510000440 - Hyundai / Kia Turbo Syn / Super Extra Gasoline 5W-30;
- 101527 - Motul 8100 X-Clean + 5W-30;
- 152056/151526/152564 - Mobil Super 3000 X1 Formula Fe "5W-30;
- 153018 - Mobil Super 3000 Xe "5W-30.
1. 5W-30 - Demitzu Zepro Touring
2. 0W-20 - Demitzu Zepro Touring
3. TURBO SYN / SUPER EXTRA GASOLINE 5W-30
4. Motul 8100 X-Clean + 5W-30
5. Mobil Super 3000 X1 Formula
6. Mobil Super 3000 XE "5W-30
Please note if you find on sale original oil, According to the seller, ILSAC GF-4 15W-40 is a fake! His simply cannot exist in nature!
Analogs
- FROM LIQUI MOLY brand Special Tec. 5W-20 (API SM, ILCAS GF-4), 5W-30 (API SN, ILCAS GF-5). Molygen New Generation 5W-30 (API SN / CF, ILCAS GF-5 / CF) can also be used.
- The Mobil 1 brand can use 5W-30 oils (SN / SM, ILCAS GF-5).
- Magnatec 5W-30 AP (API SN, ILCAS GF-5), 5W-30 A1 (API SM, ILCAS GF-4), 5W-30 A5 (ACEA A1 / B1, A5 / B5, can be used from the Castrol manufacturer. API SN / CF GF-4).
- From brand Hyundai Oil Premium LF Gasoline SAE 5W-20 SM / GF-4, code 0510000451.
Consumables
When performing oil replacement together with new lubricant material Such will also be required. original spare parts, as:
- 2630035503/2630035504 - Oil filter for DVS;
- 2151323001 - gasket for the plug of oil drain from the pallet;
- 281131R100 - air filter;
- 311121R000 - fuel filter;
- 971334L000 - cabin filter;
- 1885410080 - Spark plugs.
- air and cabin filters;
- ignition candles (every 60 thousand km of mileage). Those. With each sixth oil replacement.
- the fuel filter changes when the symptoms of its clogging appears, is in the fuel tank.
How many oil will need to be replaced?
Given the relatively small volume of cylinders of the installed engines, then the oil will need a bit.
On average, the manufacturer for a gasoline motor indicates a 3.6 liter.
This figure is calculated taking into account possible losses in the process of performing the procedure, because in fact, no more than 3.3 liters are adjusted to the block to a normal level.
Those. For replacement, you need a standard 4 liter canister.
For a diesel unit will leave more oil - 5.3 liters.
Tolerances and Type of oils
It should be understood that in gasoline and diesel engines should be poured their types of oils. For their difference, the manufacturer uses the code designation, that is, two letters after the viscosity is indicated.
For example, for gasoline engines, the manufacturer of Kia Rio 3 since 2013 recommends filling an API SM oil (for all machines since 2004.), SL API (for DVS with an increased service life) and ILCAS GF-4 (the same oils, As the API SM on the American Standard, but the viscosity is smaller, not more than 10W-30).
As for the use of viscosity oils, the manufacturer recommends applying in different seasons of the year:
- 5W-20;
- 5W-30;
- 10W-30;
- 15W-40;
- 20W-50.
All oils presented effectively can be used in the temperature range from -30 to + 50. That is, if you are operating a car at low temperatures that reach the mark -30, then it is only 5W-20 or 5W-30.
Replacing the oil in the engine - important procedurewhich does not forgive mistakes. Consider it on the example of the car Kia Rio., very popular in our country. To the attention of readers is a lot useful informationwhich will certainly be valuable both for beginners and experienced owners. Kia Ceed.
As you know, without a qualified and timely service, any car will break, and the upset owner will eventually sell it. First you need to pay special attention car engine (in this case Kia Ceed) because it is a "heart" machine. The same applies to the choice, as well as the frequency of replacement of engine oil.
How often to change oil at Kia Rio
KIA has installed the same oil replacement range for all generations KIA CEED. So, it is once a year or every 15 thousand km. This is in theory, and in practice the situation may vary - to take at least a different operating conditions, climate change, quality road coat, driving manner, etc., depends on these factors, at what speed oil will be consumed. In this regard, some experienced owners themselves calculated the replacement interval. So, let's call the most suitable oil replacement intervals for KIA CEED:
- Every 15 thousand km - subject to speed \u200b\u200bregime from 50 km / h and more
- Every 10 thousand km - when complying with the speed regime at the level of 30 km / h
- Every 7 thousand km - when complying with the speed regime, less than 20 km / h.
It turns out that the smaller average speed, the more often the need for oil replacing
Admission and class
For proper choice Oils must be taken into account all the parameters, you should select the appropriate class and tolerance. Detailed information about this is listed in the user manual for KIA CEED.
Today it is known three generation Kia. Rio. There is a completely reasonable opinion, according to which the car is newer, the more stringent requirements for the quality of oil for him.
For example, for the KIA Rio of the first generation, it is possible to recommend oil with aPI classes SL, as well as ILSAC GF-3. In fact, now all oils coming on sale correspond to the specified classes. Here is the main thing to this standard It was not higher than the specified, that is, a higher class.
For Kia Rio second generation suitable oil SO aPI standards SM and ILSAC GF-4. It often happens when the design of the car supports and a higher standard - for example, as in this case, the SN and ILSAC GF-5 API.
The third generation Kia Rio is designed to support more modern oils With the parameters of the API SN and ILSAC GF-5.
As for the additives, it is not recommended to add them to the oil, since the truly high-quality oil should be sufficiently lubricating properties.
Viscosity
Modern power plantswhich are equipped with cars Kia Rio, have small gaps in piston group. In this regard, such motors need oil with a low degree of viscosity to avoid "dry" friction and it is better to remove heat from the heated components of the internal combustion. As a result, it turns out that with the release of all new generations Kia Rio, the recommended viscosity index gradually decreases - if earlier it was at level 40, now it is not more than 20. These parameters need to pay special attention, since the engines with less viscosity do not maintain oils with greater viscosity. In extreme cases, non-compliance with the rules can lead to premature wear of the most loaded engine parts due to their oil starvation.
How much to fill oils in kia rio
Pay attention to the volume of fuel oil for a particular motor Kia Rio:
- Diesel 1.1 75 liters. from. (Start of production - from 2011). Required volume - 4.8 liters
- Gasoline 1.2 87 l. from. (From 2011). Volume - 3.3 liters
- Gasoline 1.3 75-82 l. from. (2000) - 3.4 liters
- Gasoline 1.4 97 liters. from. (2005). 3.3 liters
- Gasoline 1.5 98-108 l. from. (2000). 3.3-3.7 liters
- Diesel 1.4 90 l. from. (2011). 5.3 liters
- Diesel 1.5 109 liters. from. (2005). 5.3 liters
- Gasoline 1.6 112 liters. from. (2005) - 3.3 liters
- Gasoline 1.6 123 liters. from. (2011) - 3.3 liters
Which firm fill
Kia Rio 3rd Generation is one of the most attractive models for Russian motorists. The main reason is that the car is going to full cycle At the factory next to St. Petersburg. This causes a relatively low price of the car. The availability of spare parts also attracts buyers. Motor oil for Kia Rio can always be found on sale. It looks like it vehicle Maintains the requirements of most motorists.
History of model, configuration
Kia Rio is compact family car with front-wheel drive. Designed by the South Korean company Kia, this car wheelboats on the roads of the planet, since 2000. A total of 3 generations of cars were released. First - from 2000 to 2005, and by the beginning of 2004 the car survived a serious restyling. Then they were collected in the Kaliningrad plant "Avtotor", a set of 1.5-liter engine, a wider range of engines was offered for Europe. The checkpoint could be selected - mechanical or automatic. The body was also two options - sedan and hatchback.
The second generation was sold from 2005 to 2009. For Russian motorists gathered sedans and hatchbacks only with a 1.4 liter engine. For European consumers in Kia Rio, it was offered to choose from 3 engines from the previous generation of machines. Since 2006, cars began to collect on Izhevsk automotive factory. By 2009, the model was again survived restyling and updated was produced up to the beginning of 2011. In addition to Russia, the release was adjusted in Slovakia, China, Indonesia, Ecuador and the Philippines.
The third generation saw the world by 2011. The exterior has changed dramatically, becoming modern and aggressive - all this thanks to the famous German designer Peter Schrier. From this time, the assembly was transferred to the St. Petersburg Plant. To this day, the car is produced with hatchback bodies and sedan. Engine options for Kia Rio are two - 1.4 and 1.6 liters. Transmissions are also two - mechanical and automatic. The car has the same platform as Hyundai Solaris. In addition, most of these cars are unified, which makes it easier and reduce their assembly. In 2014, the car passed a small restyling of the appearance.
Oil fluid for Kia Rio
Information about what is exactly poured into the car on the conveyor, contradictory. Some sources say that it is originally Zic 5W20, and then on service - Shell Helix 5W20, but all these data are outdated (from 2011). Who has now signed an agreement with KIA - is their commercial secret.
And yet it is better to pour oil? Shell Helix Ultra Professional AF with a viscosity of 5W20 will be best selection for motorists who want to save their engine without overhaul As long as possible.
Oil composition - completely synthetic, made on polyalphaolefins (PJSC). The API classifier assigned to him the highest category - SN. European Association ASEA assigned Classes A1 / B1. Oil fluid has the official tolerance for car Ford.But it does not prevent you from using it for other brands. After the car ran the distance close to 100 thousand km and kia oil Such viscosity began to degrade strongly - you should switch to 5W30 or 10W30 of the same or other manufacturer, depending on climatic conditions.
You should pay attention to such a synthetic product as Liqui Moly. Special TEC AA 5W30 German production, which has many official tolerances from Asian manufacturers, including Kia and Hyundai. The composition of the product is truly unique. Additives are chosen in such a way that they will provide a long life to anyone modern engine. The lubricant received the highest categories in API classifiers, as well as ilsac - Sn and GF5, respectively.
In addition to the above, you can use motor oils from Zic, Motul and other manufacturers. By the way, Kia allows us to use 5W30 and 10W30 lubricants for new motors. They clearly do not indicate which viscosity characteristics should be, only recommended (see photo below).
When and how to replace lubrication
Replacing the oil at Kia Rio, according to the regulations, should be made every 15 thousand kilometers. But such a long interval is desirable not to use, but to change the oil compositions in 8-10 thousand km of mileage. This is due to low fuel quality, as well as heavy operating conditions for the city, including numerous tubes, poor condition of highways.
Replacing the oil in Kia Rio will require about 3.3-3.5 liters of lubricating composition. That is, you will need to buy a 4-liter canister. It will also be for the fact that the driver floods a little more in the event of a lubricant's consumption. This procedure can be carried out independently, prepare the following tools and materials:
Replacing the oil in the auto engine engine involves a certain sequence of actions to be followed.
- Pre-engine is heated by a short trip, then the car is placed over the observation pit or drives to the overpass.
- The hood rises, the tapered neck is unscrewed for the engine fluid.
- Down in the presence of protection, it is removed to provide access to a drain plug.
- Slightly, but not to the end, the key to "17" weakened the drain plug. Under it is embossed an empty container.
- It is necessary to quickly unscrew the cork with your fingers without dropping it into the working capacity. You need to do it carefully and carefully not to burn your fingers.
- For a while you have to wait until all the liquid follows from the crankcase.
- An old filter is unscrewed by removable device. Under it, too, you need to substitute the container, as a little lubricant can be found out of the hole and from the filter.
- The residues of the exhaust oil from the bottom of the crankcase are pumped up the syringe and tube.
- A new oil filter on 2/3 volume is filled with fresh lubricant. The sealing ring is wetted by oil.
- The new filter is spinning with hands. As soon as the seal is touched by the case, you need to trust it with hands on 2/3 turns.
- A new sealing ring is put on the drain plug, the plug is spinning on its place.
- Through the fuzzy neck poured fresh oil. Periodically required to check the dipstick level of the compound.
Next start the motor and works at idle for a few minutes. After that, the level is checked. The mark must be in the middle between MIN and MAX. If below, you will need to add a bit. On this work is completed, you can ride further.
Good day to all! We continue the topic of choice oils for Kia Rio. The topic is quite extensive and ahead of a lot of work. Therefore, prepare, as there will be at least a pair or top of the articles on this car model. Today it will be about motor oil for Kia Rio. We have already talked about, but today we repeat this topic again. Also do not forget to read the articles about and her.
Motor oil for Kia Rio (Kia Rio) - SAE viscosity selection
Before buying oil for Kia Rio, It is necessary to at least glanly look at the instructions for the car. After all, how are we? We go to the store, we see the expensive oil, buy it and think that everything, the engine is securely protected. But it's not always the case. Usually the manufacturer himself recommends which oil to use in the engine. If you again refer to the instructions, you can understand that the manufacturer recommends 5W20 or 5W30 viscosity to Kia Rio oil. At the same time, 5W20 is a preferred option. And 5W30 is recommended to be used if the oil viscosity is 5W20 is not available. But in hot countries, it is better not to use the viscosity of 5W20, but to use, for example, an oil viscosity of 5W30. About this manufacturer also warns. Here is a page from Manual to kia car Rio:
Why is that? Yes, everything is simple. Engines of contemporary cars are made with minimal gaps between rubbing pairs. If before almost any engine could be pouring the oil with a viscosity of 5W40 and calmly ride, then modern cars This will not be forgiven. Oil with such a viscosity almost does not penetrate the gaps, leaving them on the verge of "oil starvation". As a result, there is an increased wear of engine parts. And from here increased flow Oils and early engine output. That is why it is recommended to use oil with a recommended viscosity. In our case, the oil for KIA Rio must correspond to the viscosity of 5W20 or 5W30. This requirement acts both for Kia Rio gasoline engines and diesel. This viscosity should be applied year-round in independence from weather conditions. With viscosity figured out. Now let's talk about the quality of the oil.
Selection of oil for Kia Rio by Quality Class API and ILSAC
In one of the articles, we said that there are three generations Kia Rio. Each generation is a certain oil. The more modern generation, the higher the quality of the oil recommends using the manufacturer in the engine. For gasoline engines KIA RIO of the first generation, it is recommended to use oil class oil according to API SL and ILSAC GF-3. This is quite old requirements. Almost all oils in auto shops comply with these standards. It is not necessary to look for these these stands. It is quite suitable for oils with quality above, for example, API SM / SN and ILSAC GF-4 / GF-5.
The second generation requires to use in the engine aPI oil SM and ILSAC GF-4. As in the first case, it is possible better (API SN and ILSAC GF-5), it is impossible.
The last generation Kia Rio requires to use even better oil in the motor, namely oil last generation API SN and ILSAC GF-5.
Concerning oil for Kia Rio with a diesel engine, then the manufacturer recommends applying oil with class quality API CH-4 and higher, for example
Motor oil for Kia Rio (Kia Rio) - What is better synthetic or semi-synthetic?
Which oil is better for Kia Rio - This is probably a rhetorical question, as it is impossible to say that one butter is better, and another worse. There are oils suitable for a particular motor, and there are not suitable. Among them are high-quality, and there is not very. Definitely synthetic oils It is better than semi-synthetic, as much quality. Plus, synthetic oils do not lose their properties much longer. But the quality has to pay. 100% synthetic is 2 times more expensive than ordinary semi-synthetic. In addition, there are still hydrocracking oils. These are oils obtained by oil hydroseintite. By reducing the cost of overbabs, the final oil is cheaper and in its properties is practically not inferior to it. But its quality hydrohydration oils lose faster synthetics.
Therefore, when choosing oil for Kia Rio It is important to choose not the most expensive, but suitable according to the manufacturer's recommendations. And also do not forget to replace in a timely manner.
Oil for Kia Rio 2012, 2013, 2014, 2015
The last third generation Kia Rio began its existence in 2011. In the line of engines there are gasoline, and diesel. Oil for Kia Rio 2014 with gasoline engine Must correspond to SN / GF-5 quality class. In this case, it will be perfect motor oil Liqui Moly Special Tec AA 5W20. This is a good hydrocracking synthetics with a middle price tag. The Special Tec AA line has a similar oil, but with a viscosity of 5W30. Photo oils below.
If you decide to buy LIQUI MOLY, then read the article first: "". I think it will help not run into counterfeit.
The second option is the original oil Hyundai / Kia Turbo Syn 5W30. This is Korean oil for Kia Rio, which manufactures Mobis. A rather good option. But for the brand will have to pay a little.
