Description Ford fuses Focus 2 restyling. Mounting block in the engine compartment

Most of the Ford Focus Car Electrical Equipment Circuits are protected by fuses. Powerful current consumers are connected via relays. The fuses and relays are installed in the mounting blocks that are located in the cabin under the instrument panel on the right side and in open space Next to the battery.
The fuse blocks for Ford Focus 2 and 2 restyling are different and respectively for each of them will be given their own photo with the location of the fuses installed in them, their face value and appointment.

Fig. 1. Rooms of fuses and relays in the mounting unit located in the Ford Focus 2 salon

Most fuses are installed in the mounting block of fuses and relays in the cabin (Fig. 1), located under the instrument panel on the right side. Purpose of fuses and relays (their numbers are shown on the block and in the figure) in Table. one.

Table 1 Purpose of fuses and relays installed in the mounting unit in the Ford Focus 2 cabin

* If available.

Fig. 2. Rooms of fuses, fused inserts and relays in the mounting unit located in the workpiece Ford Focus 2

In addition, fuses, relays and fuses are located in the mounting unit installed in the subcontrol space (Fig. 2), the cover of the mounting unit is removed). In tab. 2 is the appointment of these fuses, fuses, fuses and relays, but on specific model Car Some chains specified in the table may be absent.

Table 2 Purpose of fuses and relays installed in the mounting unit in the workpiece Ford Focus 2

* If available.

1. To gain access to fuses and the mounting unit relay, located in the cabin, remove the two screws of the fixtures under the instrument panel to the right ...

2. ... and lower the mounting block down.

3. For the convenience of working with the block, its housing can be pulled out by rearring the housing protrusions in the grooves of supporting brackets.

4. Before replacing a blown fuse, find out the cause of its brave and eliminate it. When finding a fault, browse the tables listed in Table. 10.1 Chains that protect this fuse.

A warning
Do not replace the fuses with jumpers or fuses designed for another current strength, as well as homemade jumpers - it may damage electrical devices and even to a fire.

5. Using a special plastic tweezers, remove the replaceable fuse.

6. So the blurred fuse looks like (the jumper shown in the arrow inside the holder burned and open). To replace the fuse, use the spare fuse of the same nominal (and colors).

7. To access the fuses and the relay of the mounting unit, located in the pump compartment, pull the lever on the back of the block and lift the lid.

On the inside of the cover of the mounting block of the relay and fuses located in the engine compartment, the layout of the relay and fuses are applied. There is also acknowledged tweezers 1 to extract fuses from mounting blocks, next to it are provided with sockets 2 for fastening spare fuses.

8. If you need to replace, remove the fuse (relay), swing it from side to the side.
9. Install the items in the reverse order.

Ford Focus 2 (Restyling) Location and Designation of Fuses

Ford Focus 2 (restyling) received another block of connections and fuses, namely, what is shown in the figure below ...

Good day. Today I came to the car service Ford Focus. 2 Restaling (2008-2011). He came to us with a problem in electronics. After connecting the video recorder, which closed, a lot of fuses flew out. Therefore, in this article, we will tell you how to remove and replace the fuses under the hood and in the Ford Focus 2 Restyling salon. We will also show you the scheme and location of fuses in the car.

Vendor code: Fuses and relays of all denominations

Instruments: To replace fuses in Ford Focus 2 Restyling, under the hood there is a special tweezers

Scheme and location of fuses on Ford Focus 2 Restyling:

First of all, open the hood. Then under the number 8 you will see the mounting block of the fuses.

The fuse block under the hood is isolated by a red line.

Open the fuse cover under the hood.

Outping the fuse cap You will see the appointments of each of them.

Another photo of the cover with the fuse diagram.

Now let's look at the fuse numbers and their description.

Table of block values \u200b\u200bFuse under hood Ford. Focus 2 Restyling:

№	Ampere	Description of the fuse
1	40	Engine cooling electric agent
2	80	Steering with amplifier
3	60	Internal fuse block 1
4	60	Internal fuse block 2
5	80	Auxiliary heater
6	60	Heating Candles (for cars with diesel engines)
7	30	Anti-lock system, pumping system dynamic stabilization
8	20	Anti-lock System, Dynamic Stabilization System Valves
9	20	Control module force aggregate (PCM)
10	30	Climate control fan
11	20	Ignition switch (starter and appliances)
12	40	Ignition relay
13	20	Electrical winding starter
14	40	Heating windshield, Right side
15	30	Cooling fan relays (Sigma - only options without A / C)
16	40	Heated windshield, left side
17	30	Folding roof
18	30	Inverting power amplifier
19	10	ABS Module
20	15	Sound signal
21	20	Auxiliary heater
22	10	Steering Amplifier Module
23	30	Plaidwater washers
24	15	Auxiliary heater (for cars with diesel engines)
25	10	Ignition relay
26	15
27	10	Air Conditioning Compressor Coupling
28	10	Control of incandescent (only for cars with diesel engines)
29	10	Separate climate control system
30	3	PCM, automatic transmission
31	10	Intellectual charging rechargeable battery
32	10	Automatic box Transmissions
33	10	Heated oxygen sensors (for cars with gasoline engines)
33	10	Air Cooling Air Correction Valve (for vehicles with diesel engines)
34	10	Nozzles, ignition coils
35	10	PCM, valves, electromagnetic valves
36	10	PCM.

The location of the fuse block in the cabin. Removing and replacing fuses

Now go to the salon. The fuse block is located under the glove compartment.

Remove the protective shelf. To do this, just pull it down.

Then we unscrew the 2 fuse block fixtures.

And pull down the fuse block.

Fuse block diagram in Ford Focus 2 Restyling salon:

Table of fuse block values \u200b\u200bin the cabin:

№	Ampere	Description of the fuse
100	10	Electronic modules (Powered by ignition lock)
101	20	Ventilation hatch drive control unit, driver seat with electric drive, roof drive control unit (for a / m with removable roof)
102	10	Heater regulator, steering column, diesel fuel combustion fuel filter, system receiver remote control
103	10	Power supply controls External Lighting from the Battery
104	10	Electricity Saving System, Internal Lighting Plafones
105	25	Heater rear glass
106	20
107	10	Battery Power Combination Devices, Side Diagnosis
108	7,5	Additional instrument combination functions (audio system and navigation system)
109	20	Cigarette lighter, extra electric socket rear
110	10	Food switch of the exterior lighting system during the daytime from the generator
111	15	Fuel pump (only options with gasoline engine)
112	15	Audio system modules (battery powered)
113	10	Outdoor lighting lamps at daytime (sweatshirts)
114	10	Food combination of devices from the generator, engine immobilizer
115	7,5	Nutrition of the external lighting controls from the generator
116	20	Fog lights / lanterns
117	7,5	License plate lighting lamp
118	20	Module Electrical Equipment Door (left rear)
119	15	Additional power socket in luggage compartment
119	25	Additional power socket in the luggage compartment (cars with trailer towing module)
120	20	Electrical Equipment Module (right rear)
121	20	Electric heating front seats
122	10	Airbag module
123	7,5	Electric heating exterior rearview mirrors
124	7,5	Rear and front parking lights, stop signals (left side)
125	7,5	Rear and front overall lights, stop signals (right side)
126	20	Keyless
127	25	Power windows
128	-	Not used
129	20	Windshield cleaner
130	-	Not used
131	15	Rear window cleaner
132	15	Stop signals
133	25	Relay central locking system, passenger door module
134	20	System of centralized locking locks, driver door electrical equipment
135	20	Backlight when moving in a bright time
136	15	Materom Ferrous Pump Heated Glass Berkener Jetgers
137	10	Emergency battery power speaker
138	10	Power unit control unit, accelerator pedal, automatic transmission
139	10	Far Light Headlights, Right Side
140	10	Far Light headlights, left side
141	10	Lamp rear stroke, rearview mirrors with electric drive
142	15	Middle Light headlights (right side)
143	15	Middle Light Headlights (left side)

Video Guide to Replace Fuses in the Ford Focus 2 Restyling Salon:

Ford Focus 2 is one of the most popular foreign cars produced in Russia. This car is very reliable and meets all international standards. But, despite this, whether it is too late, the owners of focuses arise with electrical equipment. This is especially true for new owners of used cars. The very first sign of electrical devices is the failure of fuses (PP) or interrupting elements (relays).

Fuses that are used in the Ford Focus 2 car are called "knife", they are flat, medium sized, plug, i.e. consist of two plug contacts with a lunch jumper in a plastic case different colors. From above on the housing, the denomination is knocked down - the power of the current, when the part is exceeded, the part burns out (the jumper melts). The main function is to break the electrical chain to prevent the failure of electrical equipment and possible fire vehicle. For the most powerful consumers, the relay is played by a protective role.

In general, according to the standard, fuses are 17 colors, while shades may differ. For Ford Focus, the following colors apply to the marking of parts of spare parts:

The location of the contact connectors, relays and fuses differs in cars released from 2005 to 2007 (the sequence number of the part begins with 37), and in 2007 and after restyling 2008 until the end of the release of this model in 2010 (the numbering begins with 100).

In the postpartum focus released in the Russian Federation, there are four options for the location of the prevention elements and relays. Versions B, C, D, E (F, J) depend on the configuration of the car. Clarification which model block is made according to the last letters of the serial number. For example, 7M5T-14A073-DG refers to the modification of D.

Location

Under the hood, if you face the engine to the engine, then on the side of the board - PP and relay for the power unit and other components in the subcontrol space (high-flow). In the cabin - fuses and interrupting elements of the mounting unit (low-current) are under gloves. The build body is fastened with two latches with a rotary mechanism. Sheltered the upholstery of the cabin, which holds on two buttons.

Working with fuse block under the hood

1. Raise the hood.
2. Open the lid. This can be done by pulling the lever on the back of the PP assembly housing. Does not work? We take the middle flat screwdriver and insert it into the lock lock. Slightly tip the screwdriver and the lid is lifted. Remove it.
3. FROM inner The covers have a special tweezers fixed in the grooves. They are very convenient to remove the fuses. Using Passatia, you can damage the case, if squeezed too much. Please note that the tweezers are only in the box near the power unit. There, on the lid there are nests for spare fuses and there must be a schematic graphic image of the location of fuses and relays.
4. We carry out the circuit and with the help of a tweezer, remove the burned element, after which we insert a new one.
5. We test the operation of the electrical appliance and close the box, pre-placing tweezers in the nest.

Working with fuse block in the cabin

The most common problems with electrical equipment:

The air conditioner does not turn on.

1. This unit in FordFocus 2 is included only if the temperature ambient not lower than +5. First of all, make sure that there is enough freon in the system. For this corresponds to a special pressure sensor. If the pressure is sufficient, it transmits a signal to the electronic unit Control and interrupting element of the air conditioner compressor coupling switches.
2. If, when you turn on the air conditioner to hear the clutch hours, the clutch and the engine does not increase the speed, then it is necessary to make sure that the pulley of the compressor shaft rotates.
3. If the pulley is immobile, open the unit near the engine, we look at the location of the F27 fuse (10a) on the lid and check its condition. This PP is responsible for the flow of current on the coupling. We remind you that the labeling and color of the body is different, depending on the year of the Ford Focus 2 and the options for assembling fuses.
4. If the replacement of the fuse is not required, then check F35 (10 A), which is responsible for supplying the power on the air conditioner compressor relay.
5. If everything is fine here, we specify where and diagnose the compressor relay. Make sure this item can be done only by replacement.
6. The last option is to make sure that the hoses and wiring are integrity, especially the wires going to the coupling, there the break occurs most often.

Sound signal (beep)

1. Check F20 (15 A) in the assembly under the hood.
2. If he is integer, you need to try the beep. To do this, remove the radiator grille and connect to Klasson's 12 V. contacts the easiest way to do from the battery. No sound - replacement.
3. If Klaxon functions, then a break in the wiring or you need to clean the contacts of the beep on the steering wheel.

Power supply dashboard

Disappears rear window heating

1. Most often breaking the incandescent filament on the glass. Carefully inspect and, if necessary, creep the opening with silver with silver or in extreme cases, replace the threads.
2. Check F52 (25a). Location: PP block in the cabin.
3. Nick wiring, clean the circuit breaker contacts.

Important! If, when replacing the fuse, it quickly blows up again, you should call the entire power supply circuit of this instrument.

The easiest and most common method of testing fuses is a replacement. Faulty fuses are sometimes visually different from the workers, they can even be nicknamed with a tester.

If the cigarette lighter has stopped working on the Ford Focus of the second generation, most likely, we are to blame themselves. The cigarette lighter socket is often used not by appointment. And the most harmless thing that can stick into it - this is a Chinese charging from mobile phone. At best, she simply closes the contacts to the spin and will work the fuse. At worst - wiring or the phone charging unit itself will light up. We will not be about sad, it is better to understand where the cigarette lighter fuse on dorestayling and restyling Ford Focus 2 is located.

Fuse set. It is better to use such.

On all versions of the Ford Focus of the second generation, the cigarette lighter fuse is located in the salon mounting unit, but its location and functions in removal cars until 2007 and after 2008 differ.

In restying focus, this fuse is responsible not only for the cigarette lighter, but also for the rear 12-volt socket. Consequently, if the cigarette lighter does not work on the resting focus, the rear socket is guaranteed, the fuse has been burned. If only the cigarette lighter, the reason you need to search either in the chain or in the cigarette lighter socket.

Restayl and Dorestayl

In both versions of the second generation of focus, our fuse is located only in the salon mounting unit, but located and numbered according to the scheme in different ways:

• in dorestayling cars he was assigned the number 39, and his nominal has 20a ;
• same 20-ampere fuse In restying machines set at number 109 In the same cabin mounting unit.

Here is the layout of the fuses in the focus of release until 2007:

Dorestayla scheme

And this scheme shows the location of the fuses in the mounting unit of restyling focus:

Replacing the fuse on Ford Focus 2

The cabin mounting unit is right under the glove compartment and to get it to get to lose two minutes. We do this:

1. Soak two screws under the front panel in the glove box.

   The Americans were gained to fame. It is necessary to hide the mounting block so much.

2. The mounting unit is lowered for the maximum possible distance.

   Somewhere here our fuses.

3. We turn fixators of supporting brackets to the right and left.
4. I put forward the mounting unit on yourself.
5. We find the fuse of the cigarette lighter and take it out by plastic tweezers.

   Everything is clear here, the fuse burned. Only replacement. No bugs.

6. We establish a similar fuse with a denomination of 20 A, it must be yellow. Installation of wires, foils, coins, clips and other nonsense instead of a regular fuse with a certain face value are not allowed.
7. We collect the mounting block in the reverse order.

But before changing the fuse of the cigarette lighter, it is necessary to deal with the reasons for which it burned. If a powerful device (compressor, refrigerator, vacuum cleaner) was included in the cigarette lighter, with consumption of current on the chain above the nominal, then simply change the fuse and try not to connect powerful devices into the cigarette lighter (it is better to connect them directly to the AKB terminals). If the fuse burned down for incomprehensible reasons, it is necessary to call the chain and find the cause of the closure. Otherwise, the replacement of the fuse will be held daily. Use the cigarette lighter carefully, successful to all travel!

Good day. Today, restyling Ford Focus 2 (2008-2011) was published in the car service. The reason for his visit is a problem with electronics. After connecting the video recorder, which closed, a lot of fuses flew out. In the article we will tell you how to remove and replace the fuses under the hood and in the Ford Focus 2 salon will also show you the scheme and location of the fuses in the car.

Vendor code:

Fuses and relays of all denominations

Instruments:

To replace fuses in Ford Focus 2 Restyling, under the hood there is a special tweezers

Scheme and location of fuses on Ford Focus 2:

First you need to open the hood. Under the number 8, you will see the mounting block of the fuses.

The fuse block under the hood is isolated by a red rectangular line.

Then you need to open the fuse cap under the hood.

The next step turning the fuse cover, you can see the destination of each of them.

Another photo of the cover with the fuse diagram

Now let's look at the fuse numbers and their description.

Fuse block values \u200b\u200btable under the hood Ford Focus 2

№	Ampere	Description of the fuse
1	40	Engine cooling electric agent
2	80	Steering with amplifier
3	60	Internal fuse block 1
4	60	Internal fuse block 2
5	80	Auxiliary heater
6	60	Heating Candles (for cars with diesel engines)
7	30	Anti-lock system, pumping system dynamic stabilization
8	20	Anti-lock System, Dynamic Stabilization System Valves
9	20	Power Unit Management Module (PCM)
10	30	Climate control fan
11	20	Ignition switch (starter and appliances)
12	40	Ignition relay
13	20	Electrical winding starter
14	40	Heated windshield, right side
15	30	Cooling fan relays (Sigma - only options without A / C)
16	40	Heated windshield, left side
17	30	Folding roof
18	30	Inverting power amplifier
19	10	ABS Module
20	15	Sound signal
21	20	Auxiliary heater
22	10	Steering Amplifier Module
23	30	Plaidwater washers
24	15	Auxiliary heater (for cars with diesel engines)
25	10	Ignition relay
26	15
27	10	Air Conditioning Compressor Coupling
28	10	Control of incandescent (only for cars with diesel engines)
29	10	Separate climate control system
30	3	PCM, automatic transmission
31	10	Intelligent battery charging
32	10	Automatic transmission
33	10	Heated oxygen sensors (for cars with gasoline engines)
33	10	Air Cooling Air Correction Valve (for vehicles with diesel engines)
34	10	Nozzles, ignition coils
35	10	PCM, valves, electromagnetic valves
36	10	PCM.

The location of the fuse block in the cabin. Removing and replacing fuses

Go to the salon. The fuse block is located under the glove compartment.

First you need to remove the protective shelf. To remove it you just pull it down.

And pull down the fuse block.

Fuse block diagram in Ford Focus 2 cabin

Table of fuse block values \u200b\u200bin the cabin:

№	Ampere	Description of the fuse
100	10	Electronic modules (Powered by ignition lock)
101	20	Ventilation hatch drive control unit, driver seat with electric drive, roof drive control unit (for a / m with removable roof)
102	10	Heater Regulator, Steering Column, Filter Solid Products Combustion diesel fuel, Remote Control System Receiver
103	10	Power supply controls External Lighting from the Battery
104	10	Electricity Saving System, Internal Lighting Plafones
105	25	Rear window heater
106	20
107	10	Battery Power Combination Devices, Side Diagnosis
108	7,5	Additional instrument combination functions (audio system and navigation system)
109	20	Cigarette lighter, extra electric socket rear
110	10	Food switch of the exterior lighting system during the daytime from the generator
111	15	Fuel pump (only options with a gasoline engine)
112	15	Audio system modules (battery powered)
113	10	Outdoor lighting lamps at daytime (sweatshirts)
114	10	Food combination of devices from the generator, engine immobilizer
115	7,5	Nutrition of the external lighting controls from the generator
116	20	Fog lights / lanterns
117	7,5	License plate lighting lamp
118	20	Module Electrical Equipment Door (left rear)
119	15	Additional nutrition nest in the luggage compartment
119	25	Additional power socket in the luggage compartment (cars with trailer towing module)
120	20	Electrical Equipment Module (right rear)
121	20	Electric heating front seats
122	10	Airbag module
123	7,5	Electric heating exterior rearview mirrors
124	7,5	Rear and front overall lights, stop signals (left side)
125	7,5	Rear and front overall lights, stop signals (right side)
126	20	Keyless
127	25	Power windows
128	-	Not used
129	20	Windshield cleaner
130	-	Not used
131	15	Rear window cleaner
132	15	Stop signals
133	25	Relay central locking system, passenger door module
134	20	System of centralized locking locks, driver door electrical equipment
135	20	Backlight when moving in a bright time
136	15	Materom Ferrous Pump Heated Glass Berkener Jetgers
137	10	Emergency battery power speaker
138	10	Power Unit Management Block, Accelerator Pedal, Automatic Transmission
139	10	Far light headlights, right side
140	10	Far Light headlights, left side
141	10	Reverse Lantern, Rear View Mirrors with Electric Drive
142	15	Middle Light headlights (right side)
143	15	Middle Light Headlights (left side)