Car UAZ-469. Designed for military department. The context of the cabin is actually absent. And the thermal insulation of the cabin too. A typical heater does not cope with its duties, and its noise of its work creates additional discomfort. Countless slots and low thermal insulation of the floor turn UAZ-469. In one of the coldest cars of the domestic auto industry.
Instruction
1. For the insulation of the cabin, first replace the heater to more strongly or install the added heater in the rear of the cabin. The choice of a certain heater depends on flavors, preferences and financial probabilities of any owner of the UAZ. But still you have to change the configuration of the stove. Recommended to choose heaters pretended for installation on minibuses. Say, Kitb.3221-8110010. This brand can be installed as a rod or additional stove. It will excellently warm the salon of a large internal volume, but has quite large dimensions.
2. It will also be suitable for the UAZ independent salon heater operating on gas fuel. Alone from the selected heater model, it must own a power of 2 to 4 kW. Such a heater charmingly harmonizes with the installation on the UAZ of gas-ballon equipment. The superiority of the independent heater is the likelihood of mechanical maintenance of temperature in the cabin. The disadvantage is the difficulty in independent connection.
3. Warm floor. When limited in finance, use warmed linoleum for this. If finance is allowed, acquire a specialized floor insulation kit in a car shop. It consists of a foil layer and a foam layer glued on it.
4. The front panel, doors, sidewalls of the body and the ceiling are improper, by obtaining specialized materials. Establish them is allowed both orosy and in a specialized firm. Doors Equipped with double seals from the car UAZ Hunter.
5. Tarpaulin awning, standard installed on UAZ-469. Replace on a warmed model of more modern polymeric materials. If you probably, order a personal tailoring. In any embodiment of the installed awning, purchase an additional insulation for use in winter time.
6. Seat all the slots in the cabin with the support of the mounting foam or specialized sealant
In the houses with grained heat insulation in winter, it may be uncomfortable in winter, from what to walk is actually in the boots. Linoleum put on such a floor actually does not give the heat insulating result. In order to improve the situation, it is not necessary to disassemble and change the entire design of the floor, it is easy to insulate the existing linoleum.
You will need
- - isolon;
- - Penoplex;
- - Natural or synthetic substrate for linoleum;
- - plywood;
- - Penoplex;
- - Fiberboard;
- - fasteners (selflessness, glue);
- - Scotch;
- - scissors, knives, electrolovik;
- - screwdriver either screwdriver;
- - polyethylene film.
Instruction
1. Remove the linoleum web and look back under it. If the boards in excellent condition, did not rot, insulate the floor, starting with this tier. Look up the door, and decide how much the floor is allowed to raise, so they closed coolly and opened.
2. Put the substrate for linoleum. If you tend to natural and environmentally friendly materials, choose the natural base from the jute fiber. Please note that it is rapidly engaged and gives dust, it can start mole and other small insects.
3. In order to avoid these strokes, you will acquire Izolon or Painoplex (with a foil on one side). Cut them into pieces of the desired size, decompose on the floor, glue with scotch all the joints. After that, impose a layer of plywood sheets on top and screw everything together with self-draws. Plywood will provide contented stiffness of the structure and will not give linoleum to fall.
4. It is permitted to insulate the floor of the linoleum primitively plywood sheets. In this case, glue the sheets with mastic or special glue for wood.
5. Die hots will be warm with your floors, if you decide to insulate them with extruded polystyrene foam (penoplex), however, learn that it is recommended for facing buildings outside, and when using indoors, it can highlight a detrimental pair.
6. If you decide to put under the linoleum DVP, strictly carry out waterproofing, so that it does not happen. To do this, put the layer of polyethylene film on the floor, after which the Fiberboard layer, the one that is worth adding to add (walked). Top Paul Close another layer of plastic film. In order to so that the moisture could not leak down, use rectangular linoleum baselinits. Scrupulously close the joints between the sheets of linoleum, and it is more cool to choose the sheets of such a width, so that the joints were not at all.
7. If you are not worried about electricity bills - to put a film "warm floor" under the linoleum.
Video on the topic
Note!
It is not necessary to sharpen under the linoleum slab from the chipboard. Despite the fact that they will give an excellent insulation, when washing floors and when collecting condensate, when collecting temperatures, wood-chip plates are able to worry, which will lead to failures and irregularities on the floor.
Helpful advice
In order to make the Salon UAZ-469 really warm, use all the above measures in the complex.
Russian winter is usually very cold time and frost at 25-30 degrees are not uncommon. Therefore, insulation for winter time as follows your car, for car owners it becomes a primary task. This work is not very complicated, but requires certain skills and patience. Solves all the good organization and materials that are necessary for the insulation of the cabin.
Materials for car insulation
Modern professional insulation are very effective, easily mounted, and if necessary, quickly removed. You can warm the car's salon with your own hands using the following materials known and the most demands:
Sequence of the insulation in the car
First of all, choose the material you intend to insulate the interior of the car. For the production of work, you will need the following tools:
- sheet cardboard;
- scotch;
- marker;
- sealant;
- rubber seals;
- screwdriver;
- scissors.
Previously, you need to call for washing and complete the interior cleaning. Then, preferably in the garage, dismantle all the seats, remove the door panels and disassemble the torpedo. All things on the rear shelf must be removed.
After inspection of the body's condition, close all holes sealant. Especially carefully process the place located between the motor compartment and the cabin. Remove the stove radiator and seal all visible seams. Change the extensive old rubber seals to new ones.
Starting the processing of the salon for insulation is necessary with the floor of the body. The bottom of the car thoroughly and process the solvent. From cardboard sheets prepare patterns.
Buy a calculated material in the store, plus a small stock. According to the pattern made from cardboard, cut the foam of the desired size. If you have a material without an adhesive layer, then you will also have to buy glue tilitis for connecting the seams of the insulation.
Go to the doors, they are also neatly rinsed and processing the solvent, then cut the holes under the handle. Glue pieces of insulation just like on the bottom. Clips are used to places with a pronounced relief, inside fasteners using furniture brackets.
Installation of thermal insulation on the Machine Machines UAZ
In the UAZ-469, another heater is installed in the winter or replace the standard on the device of high power. It all depends on the finance and taste of the car owner, we advise the heater applied on the KITB brand minibuses.3221-8110010.
If your UAZ is equipped with gas equipment, then a gas autonomous heater is perfect, but its power must be at least 2-4 kW. The electronics of this device automatically maintains the temperature mode inside the cabin, but the device must be connected to a specialist.
An additional heater is placed at the rear at the very end of the cabin.
Warm the bottom of the cabin with a warm linoleum or a set from the store designed specifically for the floor UAZ consisting of foil foam rubber. In the same insulation, stop the ceiling of the cabin, sidewalls, door panels and a place near the torpedo. Seals are suitable for all doorways from UAZ Hunter.
Place a warm polymer top instead of a tarpaulin, take away all the holes and slot slits.
Attention! To insulate the Salon UAZ-469 with their own hands, all the above must be done only comprehensively.
By establishing heat shifting on the UAZ-3909 or simply on the "loaf", it is necessary to try not to take a regular ventilation system by making a kind of thermos from the salon. If you accidentally clog the factory ventilation, a large mass of condensate will be formed in the cabin.
The mounting foam is associated with foam plastic covered with foil does not allow heat to leave the cabin and keeps quite a long time, so such a coating fully justifies itself. Another option is to obey the salon with a 4-millimeter plywood or put the porporal of the middle thickness.
A warning! The greater the thickness of your insulation - the less place in the cabin.
So for a little money, it is quite nice to insulate the Salon UAZ Buankka with their own hands.
See how the Salon UAZ Buanka Polyurethane Fiurethane can, on this link:
Heat protection equipment on VAZ family cars
Warming the car inside, we create conditions for reducing the heat transfer and maintain a constant temperature regime in the cabin. At the same time, it is also excellent sound insulation that significantly reduces the noise in the cabin. He insulates him, we see how they stop moving the car's glass, and we feel more comfortable and safely.
Similarly, we warm the salons and other VAZ cars. When traveling in the winter time on the VAZ 2115, 2110 and prior, many passengers sitting in the rear seat often pay attention to the influx of cold air in this part of the cabin. The fact is that in the rear door at the very bottom there are ventilation linings from plastic. At speed, such ventilation significantly reduces the temperature inside the cabin.
To better insulate the interior, you need to significantly reduce the influx of cold air. To do this, remove plastic lining and exactly on them, cut the desired size with a small margin from the insulation. Special glue material glit on the front side of the lining. The hole under the lining is missing Moviem and install the lining, placed insulation in place. Now the cold no longer penetrates the inside of the cabin, and the ventilation is preserved and does not allow to accumulate moisture and condensate at the bottom of the door.
Equipment with thermal insulation of foreign cars
Budget foreign cars Popular in Russia are distinguished only by better tightness and good stoves. In fact, the insulation is as such, there are no foreign production machines.
To insulate the salon in foreign cars in our frosts must be necessary. If the engine thermal insulation can be solved using a referee, then you need to work with the body. From the insulation, the foam with its adhesive base and foil is best suited.
We remove the decorative trimming of the doors, cut the desired dimensions of the insulation, leave the holes so as not to interfere with moving parts inside the door and glue to the foil part. With the trunk, everything is easier, by the way, there are even places for fastening the insulation. Usually this processing is enough.
If your region has a more severe climate, then the floor can be covered with insulation and puncture the ceiling of the cabin.
On foreign cars you can put in heat from the vibroplast - this material is not only extinguishing the vibration, but also by itself a good insulation. We pave them floor, ceiling, all doors and trunk.
To preserve the heat of the engine, we use the auto tube, although some manufacturers offer a plastic plate to close the radiator, but this is clearly not enough.
In conclusion, I must say that than careful and carefully you have been handled your car's salon, the more comfortable you will feel safer on the road.
Noise insulation UAZ rightfully refers to the so-called elements of the car tuning. It is held not only to improve the overall comfort, but also to increase the acoustic properties of the cabin (so that instead of Bass and Midbas, the ears of passengers do not torment the rice of the muffler and the engine). On UAZ Buanka, noise insulation will help effectively cope with the problem.
Noise and its features
To better understand the process of conducting noise insulation (see), you need to know enough about the source. In this case, we are talking about the noise of a particular machine.
As you know, each of the cars is distinguished by its own inherent in him, the individual manifestation of unpleasant and excess noise.
Note. The creation and introduction of full-scale noise insulation of the car salon is akin to scientific research. It is necessary not only to study everything carefully and thoroughly, but also come up with new designs, to hold a worthy tuning.
Speaking otherwise, it is necessary to highlight those special zones of the car that are most sissing and creaked. They can start disbanding the flow of air or light shaking onto them on their uneven road.
No exception, of course, and functioning mechanisms. So, the rumbling of the exhaust pipe and the operation of the engine stands out on the UAZ. No less Shumen and trunk (see), performing the role of drum on wheels in the orchestra of the Sumumic group.
Note. Interestingly, the noise level and gamma sounds are so pronounced that even the most powerful and expensive acoustic system is not capable of covering it. The range from 20 to 20 thousand Hz for noise in the UAZ is an easy level.
Clearly as a day that you need to fight. UAZ, this is not a German car, where the level of noise insulation is performed qualitatively (although fans of work on improvement on foreign cars are still held).
We also note that on the characteristics of the car in terms of noise affects not so much body as various tests coming to the share of the machine. In the process of driving, the car faces the irregularities of the roadway and the vibrations of their own motor, which over time loses the former fixation strength.
So, you need to fight with such consequences, and it can be done in different ways. You can buy ready-made kits (it is possible and domestic production) and with your own hands insulating the car, or try to eliminate the noises with priests.
Negative effects of noise
Hurting bad insulation is clear. The driver is quickly tired, its condition deteriorates. All this affects the safe driving.
Note. It is no secret that most domestic machines, including UAZ, are significantly inferior in terms of sound insulation overseas analogues. Experts argue that this is exactly what forced to appear on the market of a whole line of materials of excellent quality. They make it possible to increase acoustic and noise insulating properties with minimal efforts.
Materials and sets of domestic production
As mentioned above, various models are widely represented in the range of products for Shumkov. Kits, for example, contain all the required curly elements intended for a full-scale coating on the inner parts of the body.
Below are the well-known materials of our country's production.
Vibroplast
Differs in the following features:
- Famous vibration insulator with special composition. It is a polymer self-adhesive composition. The thickness of the material, as a rule, does not exceed one and a half millimeters. The material is separated by a film from aluminum;
- The vibration insulator is distinguished by increased strength;
- The vibroplast is an excellent tool for quickly conducting noise insulation of the inner zone of the UAZ car. Make it contribute to the unique properties of the material: it does not require warming up, it is easy to put on the surface with a non-standard design, it has the adhesive properties of the sealant;
- Most of the internal surfaces of the car are processed by this material. Some advise to lay the vibroplast and on the panel of the EAZ front, both from the cabin and the engine compartment.
Vomomat.
Material with the following properties:
- The component is similar to the vibroplast destination. Is a special sheet, perfectly absorbing vibrations;
- The visomat is a composition of polymer with a thickness of 2 or more millimeter;
- The lips of the visomate are covered with a sticky layer, which is protected by a film with anti-adhesion properties;
- The visomat is perfectly eliminating small vibrations that are inherent in the body of UAZ. It also provides an excellent shine of the inner bodies;
- Variability is not able to absorb water and has a long exposure.
Isoton
This is no longer a vibrating detergent, but noise insulator.
Possesses the following features:
- Isoton is a special noise absorber, which consists of a combined layer of lavsan, polyurethane foam, glue and metallized film. The thickness of the material is usually 10-20 mm;
- It is used greater for the sound insulation of various zones of the car, including the engine compartment (the facial material coating has the ideal oil and gas resistance properties).
Cellon PPE
This noise absorber is distinguished by the following properties:
- Has the properties of the perfect heat and sound insulator;
- The thickness of the material is usually 8 mm;
- In the role of an analogue, the CTE is often another material called Splen. It differs from "fellow" the presence of an adhesive layer, a significantly facilitating surface treatment process;
- Both isolon and splen are used, mainly for the treatment of gender, shield and. They are recommended to apply on top of the vibroplast, which will noticeably increase the noise insulation and increase the quality of the tuning of the cabin.
There is a mass of other materials. We will not dwell on them in detail.
We only note that such models like proline and bitoplast-5 are used to treat plastic elements of the car. They perfectly eliminate the characteristic creaking of plastics details.
Regarding the complete elimination of noise on this car, I would like to mention the following. On olders who saw Uaazi, it is difficult to conduct noise insulation, problematic, ineffective, and simply speaking, it is useless.
If the machine is relatively new, it will not be necessary to fight with rattle glands and whistle through the gaps. It will be enough to eliminate the noise published by the exhaust pipe and the engine.
main sources
We highlight the main sources of noise on the UAZ:
- Exhaust system (silencer and other elements of the exhaust path). Noise source, rather, the most important. It is with him that it must be struggling first.
Note. Some experts believe that the increased noise from the exhaustion on the UAZ arises due to the incorrectly selected silencer. As a rule, it is necessary either without a resonator, or the resonator is after the silencer, and not to it.
- The second source of noise, this is the engine, which is also incorrectly, is poorly adjusted. It is recommended to first take up setting and adjustment, and then then start the engine compartment noise insulation;
- Hard suspension system Motor / PPC UAZ is also considered as the cause of noise. Most likely, if you put a soft but rather thick rubber, the problem can be solved;
- The heater fan in the cabin is also considered as noise source.
Note. On UAZ 469 Motor stove stood under the hood. Incidentally, the noise from it to the passengers and the driver sitting in the cabin did not reach. In UAZ 3151 heater air intake only one. So the designers had to put a motor under the stove itself.
Noise elimination work
So, to reduce the level of UAZ noise in several ways or combination of all systems described below:
- Conduct a thorough sound and vibration insulation of the hood (see) and other zones of the car, which reduces the noise level of 20 percent;
- Modernize the heater motor, putting a fan from the gazelle;
- The muffler is wrapped with a leaf of refractory material (asbestos), and on top of putting a galvanized iron sheet.
- You can transfer the main silencer under the "belly" of the car. Thus, it is possible to achieve a decrease in the temperature of the muffler, which will have a positive effect on the galvanized and its service life;
- Salon processing from inside with high-quality vibration insulator. It will help to cope with low-frequency noises arising from UAZ vehicles at a speed of 80-90 km / h;
- On the door to put a double seal;
- To smell the floor of the foam crumb mixed with bitumen mastic. Such a porous mass will create sound insulation and excellent anticorrosive;
- Use a rug-foam. Sale in a sports store. The price is funny - 150 rubles, but the effect is excellent. It will be necessary to remove the covers in the floor UAZ, covering the box-distribution mechanism, rinse in the bathroom with powder, dry and wrap pieces of foams (cut from the rug), treated with glue. Then put on places;
- Between the heater and the engine compartment panel, it is recommended to put a large piece of the same rug, but without glue. It is necessary to push the material in the gap (6-10 mm);
- Take advantage of the noise-absorbing casing. Put it on the area of \u200b\u200bthe lever covered with a leatherette with a foam layer. This event will help eliminate the noise of disassemble and engine.
Now, in fact, about the very process of noise insulation specifically:
- Paul is preferably saked with polyurethane foam rugs (purchased in a store for fishermen, hunters and tourists). Dimensions of rugs, as a rule, 80x200 cm.
They will be excellent to keep warm, and most importantly - will be practically not to miss noise. It is desirable to plant mats on a polyurethane mounting foam (only "Penoflex", but not "macroflex"). Foam carefully lay in the zones of the slots at the junctions of the rugs.
Note. Before carrying out the treatment of the floor, it is advisable to carefully disassemble everything. It will be necessary to remove the seating and the casing that closes the box with a distribution. Rugs cut along patterns, and then start glue.
- In the same material, you can handle the hood, tunnel of the checkpoint, the engine compartment partition;
- The hood should be given a separate attention. Here, the material is desirable to put in the form of foil foam (above detailed materials). In the location of the gills, it is necessary to make slots on the material or to get the ventilation in the summer, and in the winter you can close.
Note. It is necessary to fix the material on the hood, removing before the cover and the pigment all the factory elements that prevent the label of the foam sheet. You must not forget to adjust the locks so that the hood is locked without problems. It is also recommended all over the perimeter of the hood to put on the Zhigule door seals. Thus, it will be possible to cope with rattling.
UAZ can be noise insulated in another way:
- Remove and construct all factory stuff;
- Purchase the necessary materials for heat and sound insulation (thermal conductivity of the material should be like a 20-centimeter brickwork);
- Singing the material (8 mm) on the metal surface of the floor.
- By factory sizes, you can order a sewing insulation from felt and black leatherette. These materials are put on the floor, and on the side vertical surfaces of the doors to fix with self-draws;
Grigory, since childhood, adored the car, and in adolescence, when he independently connected the car radio in his father's nine, realized that the cars would be his work, a hobby, vocation.
UAZ cars of the Buckka family are produced from the 50s of the 20th century and are not losing popularity to this day. In the standard configuration, the machines are available without insulation, so it is difficult to maintain a comfortable temperature in winter. But any car enthusiast can produce tuning with her own hands by performing insulation of the cabin. Depending on the budget and the presence of free time, you can choose a specific technology and material.
A certain technique is selected in accordance with the budget. The thicker layer of the insulation, the better the temperature is preserved inside the cabin, but at the same time the internal space is reduced. First you need to make preparatory work - clean the salon and calculate what a heater will fit.
In Buanka for efficient heat resistant, the installation of additional heating equipment is also required, or replacing the regular one more powerful. If the machine drives gas, a gas heater is powered by 2 kW. An additional heating element is fixed to the ceiling, or installed in the back of the cabin.
Fireproof building materials are used for thermal insulation. At the same time, the insulation must be light and flexible, as well as vapor permeable. The material selected for insulation needs to be bought with a margin. Most often used the following types of products:
Required tools for insulation cars
First of all, a construction knife is required, with which the heat-insulating sheets will be cut. Also for work it is necessary to prepare the following tools:
- cardboard sheets;
- malyary Scotch;
- portnovo scissors;
- marker.
When the insulation is mounted without adhesive layer, or it is bad, it is glued to the surface, the glue acquire. For synthetic foamed materials suitable glue "Tilit". Instead, liquid nails also use. If the insulation is planned to use mineral wool, it is necessary to use protection tools to work with it. We will need strong rubber gloves, respirator and safety glasses.
The advantages of a specialized set for UAZ insulation is that for each model, the parts are sold, fitted in size. Therefore, you do not need to cut holes on the handle on the doors and do measurements. It remains only to attach mats in the right places.
Such thermal insulation is designed specifically for operation in the car. It will not twist from moisture or highlight harmful evaporation when heated. It is desirable that the door seals and fastening are also intended for loaf.
If desired, you can do without a specialized kit and buy thermal insulation in a construction store. But then the result depends on how the motorist will suit the selection of building materials and installation. To insulate the car's interior with your own hands, you can use the most demands of the following materials using the greatest demand:
- Stipol and isoton. Have excellent insulating properties despite the absence of a foil layer.
- Tiviplen-p. Produced on an adhesive basis, which simplifies its installation. Consists of three layers: polyethylene foam, facial and adhesive grounds.
- Penophol. A rather thin material made of polyethylene foam with a foil coating.
- Polyurethan. Sprayed with the help of specialized equipment, well maintains heat with a small layer of application. But for coating it is necessary to attract specialists.
- Isoflex. It is often used as a noise insulating material. It is used for thermal insulation, thanks to low cost.
Comparison of the characteristics of materials, taking into account their retail cost, see Table:
| Material | Product specifications | |||||||
| Structure | Number of layers | Thickness, mm. | Operating temperature range, ° C | Thermal conductivity coefficient, m2 / s / watt | Density, kg / m3 | Parputability, mg / (s) | The average cost, 1 m² | |
| Isolon | polyeneetylene with closed cells | 1 | 2-8 mm | -600-+100 | 0.03 or more | 66 | 0,001 | 50-150 p. |
| Isoflex | foamed polyethylene with foil or lavsan coating, self-adhesive | 3 | 3-10 mm | -60-+90 | 0,035 | 30 | 0 | from 60 r. |
| Tiviplen-P. | anti-adhesive film, glue layer, polyethylene foam, outdoor PVC coating | 4 | 4, 8, 15 mm | -45-+70 | 0,037 | 20-80 | 0 | 200 r. |
| Mineral wool | fiberated material from melts of rocks, such as basalt | 1 | 30-100 mm | -40-+120 | 0,048-0,070 | 50-200 | 0,49-0,60 | 70-150 p. |
| Penophol | polyethylene foamed material, aluminum foil | 2 | 2-10 mm | -60-+100 | 1,2-1,23 | 35 | less than 0.001. | 100 p. |
| Polystyrene foam | gas-filled material made of polystyrene and its derivatives | 1 | 20-100 mm | -50-+75 | 0,031-0,05 | 33-150 | 0,0013-0,05 | from 150 r. |
| Styrofoam | gas-filled material made of foamed plastic masses | 1 | 20-500 mm | -40-+60 | 0,052 | 125 | 0,23 | from 70 p. |
| Polyurene Foolder | gas-filled plastic based on polyurethane foam | 1 | 50-100 mm | -100-+30 | 0,020-0,041 | 30-80 | 0,00023 | from 450 r. |
Comparison of materials for thermal insulation of car UAZ Buanka
Styrofoam it is not recommended to use, as it breaks easily and crumbs. As well as polystyrene foam, the foam begins to smooth at a temperature of +65 degrees Celsius with the release of a dangerous health of the sytic acid. It cannot be used when the roof is insulation, since in hot weather the metal surface can be very hot. Either before the summer season will have to remove heat insulation.
But unlike the Minvata, the foam does not highlight fine dust, settling in the lungs and irritating skin. When used in the cottage in the cottage, the mineral wool is in a static state and does not pose a threat. During travel by car, under the influence of vibrations, harmful particles begin to break through the trim.
Specialized thermal insulation for UAZ cars with a relatively small thickness retains the temperature well. Felt, batting And other technicians do not give sufficient effect. These materials strongly absorb moisture, which is unacceptable in the car.
Dampness in the cabin will cause rust on the body, if you choose insulation from natural fibers. Metal parts before laying insulation need to be processed from corrosion. But it is better not to cover metal with butmeal mastic, as they quickly destroy.
The easiest way to use an insulation set for UAZ. Pre-installation foam seal slots through which cold air penetrates. It is important to monitor that the ventilation remains open, otherwise condensate will be formed in large quantities. As a result of high humidity, the metal will begin to be covered with rust.
The foam rubber is glued to the bottom, ceiling, doors and sidewalls.
Also, the material is placed under the torpedo.
In order to protect against drafts, regular doorway seals are removed and replaced with them new.
To reduce the time of the engine warming, they acquire the auto industry. It differs from the usual blanket with the fact that it is made of high temperatures resistant, electric current and aggressive textile environments. However, the product is not solid and in the fields of the junctions passes cold air.
With the auto ladder, the engine warming time is reduced by half to two times. Under normal conditions, the power unit cools over 40 minutes, and on a closed blanket saves heat to 6 hours. But it is important to correctly put it, otherwise the benefit from the device will not be.
For details on the process of insulation of loaf, see the useful video:
So that in UAZ was comfortable even in thirty-permanent frosts, some drivers will use Minvatu. It can be combined with a layer of foil foam or isotone. Each mat needs to be wrapped with polyethylene so that moisture does not fall inside.
The sheet may turn out to be thicker in which it is placed. In this case, you can cut the Minvatu using a knife or metal line.
After bookmark, the insulation is covered with plywood sheets. You can cut the phaneer with the help of an electric bike, and attach a screwdriver to the framework.
These materials do not withstand strong heating, so before laying the sheets you need to puncture the salon foil. It has heat-resistant properties and avoids strong heating of foam in hot weather.
The sheets of the polyterol are attached to the glue "Titan", as it can be dissolved from ordinary sheets. If the foam is selected, it is fixed using liquid nails, for the application of which the mounting gun will be required.
Equipment for applying PPU is working with low or high pressure machine. They are intended for spraying liquid polyurethane foam. When applied, a chemical reaction occurs, as a result of which the sprayed mass increases in volume. This reaction takes place in just a few seconds, then the polyurethane foam quickly hards.
Plus polyurethane foam coating - the rapid application and the absence of seams, a monolithic surface is created. To create a comfortable microclimate in the cabin, a fairly thin layer of polyurethane foam. Minus such a way - payment of services of specialists will cost more independent installation of rolled or sheet insulation.
There is a simpler method that does not require the involvement of skilled workers. Polyurethane foam mats are taken, which can be purchased in the sports department or shop for hunters.
In the place of the joints also pour foam.
Lists of thickness of only 3 millimeters perfectly retain the temperature, and they can be mounted on any surface - floor, ceiling, sidewalls. Therefore, this material owners of loaf prefers most often.
The technology lies in the fact that the insulation is placed in the gap between the metal frame and the outer trim. But first it is recommended to welcome amplifiers - ribs of rigidity.
Plywood and materials for interior decoration will be required. Usually, the thermal insulation layer is immediately trimmed, otherwise it is quickly damaged and comes to disrepair. On top of plywood you can fix the skin, which also has thermal insulating properties.
Procedure for work
Previously, it is necessary to clean the cabin, remove dust, soot and fat from surfaces. Next, remove interfering details, first of all, seats. If the salon is finished with carpet or other material, you need to remove it. Surfaces will not only be cleaned, but also to degrease the solvent.
At first, measurements are made, then made of cardboard sheets. That is, you need to cut the parts from the cardboard sheets, then put them on top of the material and circle with a marker. After that, you can cut, without fearing to be mistaken.
First of all, thermal insulation is glued to the bottom, not forgetting about the wheeled arches.
Considering the size of the warmeted sections, cut out blanks from cardboard. Cardboard fragments are put on top of the material and score their borders, the parts are cut. Metal surfaces are washed with soap and dried. Then the metal is degreased by a solvent. The insulation is pressed to the surface and carefully smoothed.
Initially, UAZ Buankka cars were intended for service purposes - firefighters, police ambulances. Only since 2016 began to produce insulated models with internal trim. If the car has been released earlier, it is possible to produce thermal insulation yourself without referring to the specialists. The operation does not take much time, as a result in winter, it will be faster to warm the salon, which means the engine itself. When insulating a car, the driver will also improve sound insulation and get rid of condensate in the car.
How to insulate UAZ Buankka with their own hands: 6 step-by-step instructions for car insulation
5 (100%) 1 votedWe have UAZ insulated with a foam of 2.5mm on the sides of the stored, the floor of the foam 0.5cm substrate in the form of insulation, plywood, linoleum.
What do the rules think ??
Viktor (SURAMUMU) The main thing is that the gaps were not. With good heaters in the cabin, warm enough and without additional. insulation.
Maxim (PERSEPHONE) There is an oven "Bourgehog" with her hour 3 without raging heat, and at night freeze (when UAZ was without insulation)
Alexey (Hadly) I have a foam foam 4.0 mm. And the seminated roof of the adhesive insulation.
Maxim (Persephone) Alexey, how does the foam of the norm holds heat ???
Alexey (Hadly) norms warmly keeps good and noise insulation !!!
TEMNILA (Farlee) sheet foam ~ 20 mm between gods, Feds regularly covered with foaming and skin of young dermatantine but it is from this year, and before that there was a Ming Wat laid under the trim, everything is good but a lot of dust
Maxim (PERSEPHONE) We thought cotton wool but she probably take moisture and water?
TEMNILA (Farlee) Two years with cotton traveled negative except dust not seen
Alexey (Hadly) Nastrig Striped Polyuritan from Packing Comp. The monitor, stuffed in all the cracks, on the floor pendant, I wrote under Phaneru. Dust is much smaller, almost no !!! Drinking on a fluff constantly.
EDIK (Lesio) is still outside of the body joints you need to walk with a liquid transparent nail
VYACHESLAV (MIKSA) Polyfoam 30mm, self-adhesive falzed insulation
Ramil (Carr) is a good thing to insulate a foam, but somewhere will creak, you have to re-remove the trim and die!
Alexander (Kimiye) Minvatu in bags dark for garbage Pihot did not dust not moisture not spinning and there is no screenshot
Anzor (Tyla) Sasha, and how long has such creation costs and how is the soundproofing? Simply, he looked at Minvatu himself, just not in bags, but in a stretch film (but 100% more interesting bags), but confuses the possible condensate in this very film or bags like yours. As a second option, we consider the foam.
PETR (YENTE) I have in the realties of vibration insulation sticked by Tekhnonikol, Shumka - Minvata, all doors along the contour Zhigulevsky seals. The stove is redesigned - radiators and pump are connected. And Bukhaner has such a feature - a lot of holes and cracks in the body, such an assembly, they are in place: you are in the hands of foam, sealant silicone and most importantly own hands and an increase :) good luck :)
Andrey (Allan) pair of mounting foam ballons, splane good (thicker) and foil thermal insulation, the thermos effect is achieved, the main thing is not to put the factory ventilation of the cabin as the condensate in the frost will be assembled. Well, it turns out very warm. On the top of all the places of the factory trim, Phaneur 4mm + vaporizolation or ordinary foam rubber is not very thick, well, in addition to the furniture stapler in order to drag the Faneur. It turns out very warm, very beautiful, not expensive and practical. Nothing excess sounds of creak and everything else.
Evgenia (Ahuva) Do you have works, before and after?
Alexander (Kimiye) and iron with this fur coat did not rust?
Besarion (Mehri) guys tell me and will not rust from the foam? They say that foam evil?
Tags: How to insulate UAZ loaf do it yourself videoBuanka UAZ-452 / UAZ-3741 Upgrade Part 1.
UAZ will be used for hunting and fishing, for departures on ... UAZ 452 Tablet Buanka insulation Salon ... Detailed video instruction - Duration: 34 ...
☆ Cars and motorcycles ☆ | Thread Starter: Armas
UAZ Buanka
The salon is suited, enhanced with kerks and insulated.
Disc brakes.
Forged disks departure 40mm. Elevator 120mm. Strengthened front springs, power steering, power bumper, DVD, MP 3, TV, folding seats rear rear bumper, copper radiators of salon heaters, and much more.
Gennadiy (Claxton) When the hands are gold!
Alexander (Bryga) as 105 Cruise
Alexander (BRYGA) who does not need to do anything.)))
A (Gregoria) Chentr
A (Gregoria) SHTA L; AVNA
oleg (Mr. Wonderful) UAZ This sale is sold or Vadil Ponte Buck?
Olga Stefanovich (Lashkevich) Bukaka is Buanka
A (Gregoria) loaf, but with not bad stuffing, in my opinion
Sergey (Arrigo)
Alexander (Bryga) These are needed to be released from a conveyor
victor (Anugya) all of course good but UAZ will remain a UAZ
Coffee (lilly) drunk hunters ruins go
Melnichenko (Lavina) And it's not a sin!
Sergey (Arrigo) Dream of Hunters and Fishermen!
Vyacheslav (Alley) diesel or gasoline?
I (Hazaia) and shovel already turned out - how will the boy be able to steer?
05 (Corie) Liberate ... Just someone has money and time and here you do not know what to spend ....
I (Hazaia) yes full pipets
Peter (Armas) for fishing trip or hunting No "Cruise" with nor will not be compared.
How to insulate loaf for winter ?? | **** UAZ-452 club "Buanka ...
Oct 12. 2012 - UAZ is insulated with foam plastic 2.5mm on the sides washed, the floor from .... who can throw a photo - as a meat grinder to put on the engine.
What can be insulated UAZ "Bukaku"? - Ecotermix - high-quality ...
Photos of insulated objects ... Those who still thinks how to insulate the UAZ-"Bukka", you should pay more closely to this method ...
