Motor oil for VAZ 2109 carburetor. How to change the engine oil on the nine. Motor oil replacement frequency

The question where to fill the engine oil in the VAZ 2109 is obvious to each owner of the machine, which is at least a bit disassembled in the engine device. It is necessary to unlementally unscrew the cover of the oil-colored neck (it is shown in the picture at the top) located on the engine housing on top.
It opens by turning on ninety degrees against the movement of the clockwise. Through the oily neck, the oil and poured into the engine.
A more difficult question that is far from everyone can answer - which oil is pouring into the engine VAZ 2109. And just how much it takes it.
Our article will help you deal with all these difficulties in order.

Which oil pour

Everyone knows that the heart of the car is his motor (engine) and that the aggregate requires increased attention. The quality of the oil used depends largely its service life.
Therefore, let's start with the most important question, what kind of engine VAZ 2109 oil to fill? Of course, each owner tries to use expensive.
Although now, due to the large number of fakes, the high price does not always mean due quality. The use of low-quality oils (and lubricants of non-specific technical conditions) leads to increased wear of the parts of the motor and its premature failure.
How to determine the brands suitable in a huge variety and firms of engine oils, to which it is worth paying attention to when choosing:

• First, you should read the manufacturer's recommendations. Carefully examine the service book of the machine to understand which oil recommends the manufacturer in this motor And its viscosity
• If your car already has good mileagehere it is necessary to know the degree of worn out of the parts of the motor, and which oil was used
• For example, if in where the mineral oil is poured, for several years, microcracks in the gaskets of the motor are filled with sediments, during the operation of the machine they do not wash away
• However, when replacing mineral on synthetic, with higher penetrating and cleaning characteristics, such deposits are washed away, and fluid oil through these microcracks is outward, and your engine suddenly begins to "sweat"
• Golden Middle Between Mineral and Synthetic Oil, is a semi-synthetic
• Meanwhile, the concepts of "semi-synthetic", no anywhere except Russia
• Often, the lubricant of this type is obtained from mineral water by hydrocringing, which significantly improves its characteristics.
• The main advantage of semi-synthetic, primarily the price
• In addition, for the motor, for many years worked on the mineral lubricant, the transition to the semi-synthetic will not be particularly critized (if, of course, the oil was worthy of quality)
• The following criterion for choosing lubrication is its viscosity, which characterizes the ambient temperature (air) in winter During the launch of the motor and temperature in the summer at the highest load

How to choose a lubricant with the desired viscosity value:

• Today in the world there is a standard SAE classification, in terms of viscosity
• In marking on SAE is the most complete and short description All properties of oils
• They are divided into winter classes (0W-20W), as well as on summer (20-60)
• Viscosity class is denoted by a dual number
• In which the first digit means a dynamic viscosity at a winter minus temperature at which a light engine start is guaranteed.
• The second digit means the kinematic and dynamic viscosity of the lubricant at 100 ° C and 150 ° C in the summer
• SAE classification tells the consumer data of oils having a limit temperature of work at which the motor is scrolled by the starter without problems, and pumps the lubricant when the engine is cold started to dry in its driving nodes
• 50-60 viscosity lubricants are intended for powerful motors, as well as for motors that have a decent mileage (over a thousand kilometers)
• Synthetic in such engines will constantly flow through the glands, gaskets and other seals due to their increased fluidity

What else needs to know the owner of the VAZ 2109, which oil is pouring taking into account today's specifics:

• Motors, which are currently installed on many VAZ models, are very different from those that were installed earlier.
• Main features - injector fuel supply system and equipment of neutralization system (afterburning) of exhaust gases, which meets the requirements and standards "Euro2"
• Because of this, fundamentally new (increased) requirements for the properties of lubricants began to occur.
• Therefore, in the late 90s, the AvtoVAZ manufacturer made special amendments to its own system of standards and tolerances of lubricants, which was developed in the 70s
• Taking into account the specifics of the "VAZ" car park, the VAZ Scientific and Technical Center developed a two-step system of motor oil standards
• They were two main classes - super "and" Standard "
• "Standard" is recommended to apply in the "Classics" engines, which is released no later than 1.10.2000 years
• According to aPI classification - The "Standard" oil belongs to the SF class, which is now mainly complied with mineral products, as an example - "TNK Motor" (SAE 10W-30 or 15W-40 and 20W-50)
• For VAZ-2108 .. -1111 models, and VAZ cars, released later than 1.10.2000, recommended super-class oils that correspond to SG properties
• Oil class "Super" recommended for cars issued on Zaporizhia and Lutsk and factories in the same period
• For example: in the assortment of the most widely represented oils TNK class "Super" have semi-synthetic "TNK Super" (corresponding to SAE 10W-40 and 5W-40) and mineral water "TNK Super" (corresponding to SAE 15W-40)
• They are recommended for use in injection engines, which are equipped with system neutralization systems (exhaust) gases
• In 2003, the TNK Super oil was repeated technical tests, following which it was allowed to use newest models cars with periodicity of replacement 15 thousand kilometers
• This means that the "service period" in the "Super" products are significantly increased, so they provide reliable operation more than other lubricants with the usual 8 - 10 thousand mileage between shifts
• However, it is necessary to take into account such factors as: the quality of the fuel used, the engine operation mode, the contamination of roads, as well as the ability of the filter elements of the machine to operate more than 10 thousand kilometers
• Now that it becomes clear for the VAZ 2109 - VAZ 21093 What to fill the oil, go to questions when and how much.

When to fill

The deadlines for the replacement specifically for each motor, the type of lubricant and the operating conditions of its own, because for each manufacturer, it is different, plus the mileage is of great importance overhaul Motor, so we take on average:

• Under standard operating conditions of the car, lubrication should be changed every 10,000 mileage kilometers
• In Russia, the interval between replacements is better to reduce to 7-8 thousand, since the operation of transport, by the experience of many motorists, is under difficult conditions
• Intimately when changing the oil should be changed and

We define the quantity required for the fill

To determine the amount of oil in the engine, there is special Property - The meter, which is located in the middle of the cylinder block on the right side, as indicated in the photo.

To add (pour) lubricant to the motor you need to have at hand:

• Fresh engine oil with viscosity appropriate specifications for your motor
• Bulk funnel, instead of which a cropped polyethylene bottle is suitable
• Pure rubbish

Useful tips:

• To reliably determine the amount of oil in the motor crankcase after the trip, it is necessary to drown out the engine, give the oil to the pallet, waiting 5-10 minutes
• If you tighten the lubricant, use the same brand and firm that poured into the engine when changing
• It is not allowed to exceed the level above the label maximum on the probe - the meter to avoid leakage through the glands and gaskets, and increase the flow rate
• Perform level measurement by installing the machine on a horizontal level platform

Order procedure

In order not to be mistaken, and do not stop higher than the required level, and thereby not creating yourself unnecessary problems with the motor, you should check the lubricant level of the PCP, as the instruction and the following tips:

• Remove the dipstick - the meter from the motor and wipe its surface with clean rag, then insert it into place
• Remove the dipstick again, the oil level in the motor must be located between "min" and "Max"
• If its level is lower, then drop to the required level

Marks of the minimum and maximum allowable level on the probe - meter

• Remove the cover with the oil-colored neck
• Insert the funnel in the neck and plot the oil by checking periodically the dipstick - the meter its level
• To correctly check the level, let's quit 2-3 minutes after the top
• If suddenly the level after the topping exceeds the "Max" mark, it is necessary to remove excess lubricant
• It is easy to do with a medical syringe, putting on it a flexible tube, inserting the tube of the syringe into the hole of the probe, and by pumping the excess
• In winter, it is not necessary to use lubricant in the engine with a viscosity higher than necessary, otherwise in frosts will be difficulties with the start of the engine

Now questions like on the VAZ 21093 how much oil is pouring, they disappeared by themselves, fill in the level and when changing the attached instructions for the operation of the machine. In addition, you can easily pour the right amount in your own hands.

Whether flushing is needed when changing lubrication in the motor

The last question that stands in front of any owner of the car when changing lubrication is needed whether flushing is needed.
Flushing is necessary:

• If you do not know which oil was used at the previous replacement or forgotten
• If we decided to change the brand
• If the engine fused from the motor is strongly contaminated

In other cases, washing is the personal matter of each owner. She has its pros and cons.
The advantages include:

• Removal of soot, row of precipitation and sediments from the lubricant system, as well as the wear products of parts that are not washed with oil
• Cleaning from the previous lubrication will be removed new on the occurrence of precipitation and loss of properties in case of incompatibility with the previous brand

Minuses:

• Flushing is washed out of the motor not all, the remnants of it, dilute the new lubricant, from this it loses a little in the properties

therefore best washing is a lubricant that will be used subsequently, although it can be expensive to use it as flushing. Flushing usually require motors having a large mileage.
That's all, the question is on the VAZ 2109 where to pour oil to close once and for all, I hope. If you forgot something or not completely understood, read from the beginning or watch the video.

One of the key nodes of any machine is a power unit. Motor service life is largely affected by the overall reliability of the vehicle. To extend the motor testing, it is necessary to take care of the timely replacement of oil in the VAZ 2109 engine. First you need to figure out which oil to fill.

Motor oil varieties

There are several different types of lubricants for engines of cars that we will briefly consider now to make it easier to make the right choice.

Mineral

Traditionally, such oils are made on a mineral basis, but they are poorly suitable for VAZ 2109 engines. The fact is that they do not meet the requirements for the replacement of oil and do not satisfy the tight operational characteristics of the power units.

Such oils for VAZ 2109 are also made on a mineral basis, but they add some synthetic components to improve the characteristics of lubricants during the cold start of the motor. Semi-synthetic oils Support the purity of the inner surfaces of the motor and reliably protect it from wear.

Synthetics

On basic synthetic oils, motor oils are created with high performance characteristics. They are suitable for pouring both gasoline and diesel power units. Guarantee reliable protection against wear and well lubricate working mechanisms even at the moments of cold start. Synthetic oils Minimize friction harmful to the engine and maintain it in full purity. They satisfy the highest quality standards on the API system and correspond to the tolerances of automotive companies.

All-season oil

All-season oil can be any of the above. It is intended for the operation of the engine in a temperate climate and suitable for year-round use. In the winter months, such oils almost do not thicken, and in the heat under the influence of high temperatures environmental Lubricant is not very strong. Similar oils for VAZ 2109 include lubricants that have the following parameters for SAE: 5W-40, 10W-40, 15W-40.

Features of oil replacement

Filter and Tube Location

Replacing the oil in the VAZ 2109 engine - the process is not the easiest, but you can cope with this case if necessary. If you buy a used car from another person, you need to replace the lubricant in the engine, as soon as possible. It is recommended to wash the motor special fluidSo you are definitely unknown, which was flooded earlier.

The oil is also recommended to change if you have not exploited the VAZ 2109 for a long time. When the motor does not roll for a long time, condensate accumulates in it and mixed with lubricant, causing the deterioration of its property and as a result, increasing the wear of all internal parts power aggregate.

In order to extend the service life of the oil filled into the engine, we will unsubscribe dramatically or accelerate hard. We strongly recommend that you pour a certain type of oil for every season - winter or summer. Always refuel only high-quality fuel on verified gas stations. Dirty fuel burns not completely, causing lubricant contamination.

Methods for replacing oil

If you want to know how to change the oil in the VAZ 2109 engine with your own hands, you will be interested to know that there are two ways to do it:

1. Without flushing the power unit before the fill of the oil.
2. With washing the aggregate. IN this case to the bottom mark of the probe pour a special flushing fluid, the motor will plant and leave to work for 10 minutes on idling, after which the oil is drained.

What is required to replace?

To replace oil in VAZ 2109 you will need a filter, suitable oil, if necessary washing fluid. Also be robbed with rags and prepare a set of keys.

The amount of oil in the VAZ 2109 engine reaches 3.5 liters, but in practice only 3 liters typically fit into the motor. What oil pour into the VAZ 2109 engine you can learn from the car operating manual, but we recommend flooding semi-synthetic or 10W-40 synthetics from Castrol, Shell or domestic brands that have more accessible cost.

So, how many litters of oil in the VAZ 2109 engine and which oil choose you know, which means you can proceed to the process itself lubricant.

We merge the old lubricant

So that the oil is better merged from the engine, pre-warm the motor. Heat the car on the overpass or the observation pit, and you can also use the lift or lift it with the help of a jack in a flat place. Raise the front of the car by laying the stops under the wheels.

Place the tank for a drain plug, disconse it with the key and carefully unscrew your hands. Be careful and do not bother, as the motor we pre-warmed. When draining the oil, it is recommended to unscrew the lid of the oil-tank neck, which will speed up the drain process (vacuum will be disappeared at the top of the motor).

We change the filter

After draining oil from the VAZ 2109 you need to screw the bolt in drainer and unscrew oil filter. If you do not have a special key, and you cannot unscrew the filter with your hands, use a conventional screwdriver: Junk the filter across and use it as a lever for twisting. Next, lubricate the gasket and threads of the new filter and gently push it to not thread the thread. When you twist it, do not use the key, but do all your hands. It is also recommended to fill the new oil filter by approximately half to prevent oil starvation in the first instantaneous operation of the motor after starting.

The main component of the vehicle is the engine internal combustion. Its service life largely depends on the regular maintenance. To extend the resource of the power unit, you need to think about replacing the oil in the VAZ 2109 engine.

When to change?

The car manufacturer provides the replacement regulations. According to the official document, the oil replacement must be carried out once twice a year or every 10-15 thousand mileage kilometers. From time to time oil, its condition and color is checked. If it is unsatisfactory, it is also required to replace it.

Additional signs of the need to replace:

• Year of making a power unit;
• Mileage of the vehicle;
• TCA operation style;
• Seasons in which operated vehicle;
• Fuel quality;
• Loads for the engine (long work at idle, slip and tow).

Oil fluid color black, and viscous and elastic parameters are lost? In such a situation, the fluid varies regardless of the deadlines. It is done to maintain the power and extension of the motor.

Select Oil

How to choose the right oil? Such fluids are divided into three main types:

• Mineral oil;
• Synthetics;
• Semi-synthetic.

For VAZ 2109, mineral car is not suitable. Such lubricant does not satisfy the requirements if the car is operated in difficult conditions.

Semi-synthetic used for VAZ 2109 . Fluid base - mineral oil With the addition of synthetic components. This allows it to reliably cope with the protection of the inner surfaces of the motor and reliably protect it from excessive wear.

Synthetic is created taking into account high performance characteristics. It protects the power unit from wear, high quality lubricating internal mechanisms even at the moment of cold start. Synthetic components Reduce the friction of internal parts and maintain them clean.

But there is another type of car - all-season. This is the perfect option for VAZ 2109. Suitable for the Russian climate. IN winter time The year does not thicken the liquid, and in the heat is not strongly diluted. The main parameters of the viscosity for the motor of this vehicle: 5W-40, 10W-40, 15W-40.

Replacing the oil in the engine VAZ 2109 do it yourself

Required tools and materials:

• Set of wrenches;
• Screwdriver (slotted and cruciform);
• Capacity for spent oil;
• Overalls;
• Fresh lubricant;
• Wash liquid (if necessary).

The volume of engine oil according to the operation manual - 3.5 liters. In practice, only 3 liters are fitted. It is recommended to cast semi-synthetic or the synthetic of popular brands (Castrol, Shell). It is possible to use domestic analogues that have an affordable cost.

To qualitatively drain oil, before replacing, the engine must be warm up.

Replacing oil on VAZ 2109 carburetor and injector

Replacing the oil fluid on the VAZ 2109 carburetor and the injector does not require auto knowledge from the owner. The oil replacement procedure is similar to both the carburetor and the injector:

1. Heat the engine. Hot oil is less viscous. This allows it to more quickly and efficiently merge into the container.
2. Put the vehicle on a flat surface, tighten the handbrake.
3. Remove the engine protection (if present).
4. Substitute an engine tank for a used oil fluid crankcase and unscrew the key to 17 mm drain plug.
5. Wait 10-15 minutes. Oil alters in a prepared capacity.
6. While the lubricant merge, dismantle the oil filter to replace. A special key or screwdriver is used. A new filter element is installed.
7. Oil completely glass? Wrap a drain plug in place.
8. Pour in a new filter a little car. Wipe the sealing gum with a rag. Install the filter into place. Twisted with hands.
9. Pour motor oil through the neck. It is on the engine. Pour neatly, slowly.
10. Pour about 3 liters of fluid. Wait until it spreads in internal mechanisms.
11. Slowly add still half liters of the car. At the same time control the oil level through the dipstick. If the washing of the system was not produced, then, as a rule, there will be less than 3.5 liters of oil into the engine.
12. Spin the lid, start the internal combustion engine in neutral transmission. Wait 5 min. During this time, all channels and an oil filter are filled with liquid.
13. Slide the power unit. Re-check the level of the car. If necessary, add.
14. Check the system. Outputs and other traces of oil should not be.

Replacing the oil in the engine VAZ 2108

Replacing the oil in the VAZ 2108 engine is no different from the replacement of the car in the VAZ 2109. These cars are installed the same carburetor and injector engines. Therefore, the replacement process is similar to the above described.

The choice of oil in the VAZ 2108 should be left on domestic manufacturers. Good quality, affordable price And the duration of work is the basis for choice. Recommended viscosity 5W-40, 10W-40, 15W-40.

Replacement frequency

As already mentioned in the article, the oil change in the engine VAZ 2109 is carried out every 10-15 thousand mileage kilometers.

How often does the oil change in practice? In heavy russian conditions Change the oil is required once every 7-8 thousand kilometers. In addition, the regularity of checking the level of oil fluid should be carried out once every 1000 kilometers.

The late replacement of the car adversely affects the performance of the power unit.

Imprints of late replacement:

• Turning connecting rods;
• Wear of parts of the turbocharger;
• Wear engine parts.

Oil fluid does not have time to lubricate the engine mechanisms when driving in urban conditions in the short distance. As a result, after a short time, the effectiveness of additives is reduced. The replacement of oil with your own hands according to the instructions described in the article can be carried out without problems.

Replacing the oil VAZ 2109 does not represent complexity, which allows the car owner to perform this work independently, saving on the services of the workshops of the service station.

Even with a minimum of work experience, every car owner will be able to independently perform all the necessary service work.

Preparing for replacement

The manufacturer plays an axervice interval at 10,000 mileage kilometers. It is recommended to perform a regular change of oil, which will allow to ensure the performance of the car engine.

What oil pouring

VAZ cars are traditionally unpretentious to quality technical fluidsThat allows you to use inexpensive self-samples. Plant The manufacturer recommends using lubricant with viscosity indicators in 5W-30.

Engineers advise using viscous compositions, which allows you to reliably protect the moving elements of the power unit, and at the same time cooling the motor.

We can recommend you to use inexpensive semi-synthetic, which provides high-quality motor lubrication and at the same time having an affordable cost. Remember that by acquiring semi-synthetic, you must consider the volume of the engine of your car.

Engine oil volume

First of all, you need to define you need to purchase for this work. The volume of oil in the car VAZ 2109 car is 3.3 liters. When conducting service work, 3 liters of technical fluid change.

Note that the oil volume in the engine depends on the specific modification of the power unit, so you need to clarify this data in the technical documentation for your car.

Where to fill the oil

The procedure for replacing oil on VAZ 2109 does not represent complexity. Opening the hood, you can see on the engine the cover of the plug-in neck. Remember only that opening it with a hot engine is not recommended.

Instruments

To perform this work, you will need a flat screwdriver in case of problems with the oil pump and the key to 17, which we will unscrew the plug in the pallet.

You also need to take care of the presence of vessels and capacity of 3-4 liters for old oil.

Remember that at the same time the oil filter is replaced, so you will purchase it in advance in the auto parts store.

Step-by-step instruction

Replacing the oil in the VAZ 2109 engine does not represent complexity. Every car owner will cope with this work. We are offering to you step-by-step instructions to perform this service.

Service work does not depend on the specific volume of the engine in the VAZ 2109 and the modification of the power unit.

1. Previously, you need to warm up the engine, for which we let it work for about 5 minutes.
2. The car is rushing on a garage or overpass pit. With a certain proportion of skills, it is possible to carry out all the work without a pit and overpass. In this case, you need to gently climb under the car and substitute a flat container for the old lubricant under the carter.
3. We find a drain plug on the pallet crankcase and a key to 17 unscrew it. The dark waste fluid will flow out of the crankcase. We are waiting for it until it follows, usually it takes 20-30 minutes.
4. After that, we change the filter that is unscrewed manually without using the tool. In rare cases, the filter carving can be rusted, and it is impossible to unscrew it manually. In this case, you can use the special key or simply break the filter housing with a screwdriver and act like a lever.
5. As soon as the old auto shock stops from the drain plug, you need to twist a new filter, then screw the plug in place and gently clamp it with the key. Spinning filter, you should pour some oil and lubricate rubber gasketThat will not allow her to burn to the thread and provide better sealing of the system.
6. We unscrew the plug plug located on the head of the cylinder block. We recommend pouring the oil using a funnel, which will avoid spilling it into the engine. Subsequently, such spilled liquid will burn long and cause an unpleasant odor.
7. The bay of three liters should check the dipstick, which will determine how much butter you flooded into the engine. If necessary, the fluid should be addressed so that the level is between the maximum and minimum.
8. We close the filler cork and start the car. Give the Motor to work for a few minutes, then drip the engine and check the level of motor samples again.
9. Inspect the car for the presence of outers and, if necessary, tighten the oil filter or drain plug in the crankcase.

On this, the oil change in the engine VAZ 2109 is completed.

If you allow a decrease in the lubrication level in mechanical box Carms of the car VAZ 2109 and its modifications, can arise "oil hunger" of the components of the checkpoint and, as a result, breakage of the unit. Therefore, the car owner needs to know how much.

[Hide]

Replacement frequency

Instructions for the operation of the car VAZ 2109 and its modifications recommends changing the lubrication fluid in the transmission machine through 75 thousand km of mileage. In case when annual mileage Minor, such a procedure is carried out after five years of operation of the machine.

Some drivers change lubricating fluid after 12 months of operation, this does not contradict the recommendations of the car manufacturer, but it is economically impractical. Since modern consumable fluids do not lose their qualities for such a period. But sometimes there may be a need for an unscheduled oil change, if his leakage occurred for some reason, and the type of lubricant is unknown.

Select Oil

The first copies of the VAZ 2109 had a carburetor in the system and went out with a checkpoint that was a four-stage. In her crankcase poured the recommended motor lubricantthat ensured the efficiency of the unit both in the summer and in winter. After replacing the main hypoid transfer, improved oil was required by the details of the ososticial engagement. In such quality, TM-1 and TM-2 lubricants have proven well. In addition, LUKOIL TM-5 transmission fluid was developed and implemented.

Specialists advise use in transmissions of VAZ 2109 and their modifications of lubrication that correspond to aPI standards GL-4. If the owner does not know what lubricant in the box of his "nine", it is best to use lubricant liquid aPI class GL-4. Oil TM-4 or TM-5-9P is also associated with relevant requirements. Unfortunately, the last type of lubricating fluid is found on sale is problematic, so it can be successfully replaced by TM-4-12 oil. It is allowed to use liquids that correspond to the class 75W-90, 80W-85, 80W-90 of any manufacturers, but provided that they have high quality indicators.

Level control and required volume

Repair, failed PPC VAZ 2109, operation is not cheap, so check the level of lubrication fluid should be regularly. Experts recommend to do it every 5 thousand km run or once a year. If low oil volume is detected, it should be replenished. This will provide a long service life of the box.

To check the oil level in the checkpoint, you need to use the observation pit or the overpass. At the same time, it is necessary to place the machine so that the right side is somewhat towering. It can be easily done if under the wheel to put the board, brick or other suitable object. After that, you can proceed to check the level of lubrication in the GPP "Nine".

Served

In such a word, drivers call cars with five-speed gearboxes, in which there is a measuring probe in the engine compartment near rechargeable battery. They control the lubrication level. Before removing the probe, the place around it is thoroughly wiped from dirt and dust to eliminate the possibility of getting it into the crankcase boxes. After that, the dipstick is removed and rubbed with a rag, then it is installed in its place. Now the meter must be reached again and look at the next transmission fluid. It must be between two labels, which are indicated as min and max. If so, you can continue using the machine.

Checking the lubrication level by dipstick in the checkpoint VAZ 2109

The instruction manual for this vehicle prescribes to pour at least 3.3 liters of fluid into the transmission mechanism. Experts recommend slightly increase this lubricant lubrication to 4. They explain this by the fact that the details of the fifth gear are located separately from the main mechanism and "oil hunger" can occur periodically for them.

Non-servant

Such a name has a gearbox of the first issues of VAZ 2109, which not equipped with fifth transmission. To control the level of lubricating fluid in such cars serves as a bay hole. To check the amount of lubrication, the key to 17 slightly turns away the filler plug for air pressure leveling. If a lubricant appears from the hole, it means that its level is normal. Otherwise, lubricating fluid should be addressed. In addition, it is possible to test sufficient lubricant in the unit through the hole to install the speedometer drive. It is clearly visible to the fluid level, and access is required under the car.

According to the instructions in the transmission of four-stage VAZ 2109, there are 3 liters of oil. But it is also desirable to acquire lubricant in the amount of 4 liters. A small residue of the liquid may be needed for topping in the CTP Carter during the operation of the machine.

Pulling oil

How many oil is poured into the VAZ 2109 box, it is already known, you can proceed to the plot. The process of adding lubricant to the maintenance-free and serviced boxes is different, this is due to constructive features These nodes. It is important to take into account that only the type of lubricant is used to add to this checkpoint.

In four-stage aggregates, lubricant pour through the bay hole, which can be reached only from below motor compartment. The procedure is performed by a syringe for liquid oils. On his spout dress the flexible hose and fix affordable way on the syringe. After that, the device is inserted into the plug hole and add lubricant. Pour oil into the box is needed to the desired level.

For the fate, this process is performed otherwise. Add the required amount of lubricant liquid through the hole of the measuring probe. The place of its installation is carefully wiped with a rag from dirt, then remove the probe from the nest. Perform the plot is convenient with the help of a syringe, a rubber pear of a large volume or a funnel. The device is installed in the measuring hole and add the desired amount of oil.

Replacing oil with your own hands

You can perform this operation yourself, since there are no special difficulties when replacing lubricating fluid, special equipment or tools will not need.

Instructions on how to change the lubricant in the PPC VAZ with your own hands, shared the canal VAZ 2101-2107 Repair and maintenance.

Tools and materials

To replace it is necessary to prepare the following:

1. New lubricant for fill in the checkpoint. The volume of fluid depends on the design of the mechanism.
2. An empty container for collecting waste fluid, the capacity of which should be a bit more than 3 liters.
3. Rag.
4. Water wrap keys at 12 and 17.
5. Syringe with a hose for the PPC without a probe, a funnel or a rubber pear for boxes with a dipstick.

Before starting work, it is necessary to warm the lubricant in the transmission, for this it is enough to drive 10 km.

We merge oil

Before pouring a new lubricant, it is necessary to merge the old oil spent its resource. This process takes no more than 15 minutes.

The procedure will be like this:

1. Machine is installed on the lift or observation pit.
2. The corks of the fuel and drain hole are wiped with a rapid.
3. The key on 17 slightly turns away the filling lid for the release of air from the checkpoint.
4. The empty container is substituted under the drain hole and turn the tube.
5. It is poured, at the end of the leakage of the liquid, the cover is installed in place.

While the waste fluid merges, inspect the drain plug for metal chips. If it is discovered, you should rinse the CTP Carter.

Drain of oil from PPC VAZ 2109

Pour new oil

The algorithm on the pouring of oil to the serviced and maintenance-free PPC VAZ 2109 is the same as when the oil tank.

Fill fresh oil

How else can you pour lubrication

In order to pour the desired volume of fresh lubrication, you can resort to another way.

This operation is performed via the location of the speedometer drive:

1. Carefully cleanse the place near the speedometer drive from various contaminants.
2. Then turn the speedometer cable fastening nut.
3. The drive of the speedometer is removed and covered with possible contamination.
4. Pour the lubrication fluid with a large-size rubber pear - than it is more, the faster the process of adding will go.

Necessary level transmission Oil The box is determined by the appearance of lubrication from the filling hole. As soon as they saw a fluid stream, the plug of the fuel hole must be wrapped.

On the video from the channel, the home master can be found about the procedure for replacing the oil in the PPC VAZ 21099, which is similar to the process in the VAZ 2109.

Question price

If there is no way to independently replace transmission lubricant In "Nine", the owners turn to service centers or a hundred. The cost of this operation is determined by several factors and will depend on the type of lubricant, the amount of fluid, as well as on the category of the service center. The price of 4 liters of transmission oil on the VAZ 2109 is approximately from 1300 rubles. The fee for the work performed may vary within 300-500 rubles.

Consequences of untimely replacement

If you do not comply with the frequency of replacement of lubrication in the PPC VAZ 2109, the following problems may occur:

1. When "oil starvation" occurs in the unit, the wear of gears, synchronizers and bearings in the box are accelerated.
2. Excess the use of lubrication leads to the deterioration of its technical characteristics.
3. Changes in the chemical composition of the oil, which inevitably affects the quality of lubrication of the rubbing elements.
4. As a result, the displacement of parts is accelerated, the products of their wear in the form of metal chips can lead to a junction of the gearbox.
5. Low oil level worsens the cooling of the gearbox during the car movement.

Photo Gallery

Oil LUKOIL TM-4 Oil Liqui. Moly 75W-90 ZiC G-FF Oil