Alarm "Starline A9" is very popular with drivers different cars. The system package includes detailed instructions. It allows you to connect and configure alarm. The manual also spelled out the principles of system operation. After studying user feedback and the provisions of the instruction, you can highlight the basic principles of working with Starline A9. Programming a keychain will be a simple task. Tips of experienced motorists will allow you to configure quickly. It will give the opportunity to enjoy all options. The alarm can be configured to work in or without autorun mode. The blocking function is also adjusted.
General
"Starline A9", the instruction manual of which requires studying before starting to install the system and programming a key fob, is alarm with remote engine start. It has a double-sided radio channel. Its range on the area without obstacles is 600 m. In the pager mode, this indicator increases by 2 times.
Radio signal coding is dynamic. The selection of control commands is carried out on the cursor principle. Each command is controlled by its button. It is displayed on the key fob. The system provides sound and vibrating signals alert.
In addition to the main data on the condition of the car, the keychain shows the user time, the temperature in the cabin, as well as alarm clock.
You can install the presented system on machines with diesel, gasoline or turbocharged engine type. The gearbox can be automatic or manual.
Safety regulations
Taking advantage of remote or automatic launch Engine, managing machine nodes, it is necessary to follow the safety measures to use the Starline A9 system. The instruction manual clearly indicates.
The car is important to park on a well-viewed area. In this case, it must be installed on parking brake. Lever arm automatic transmission Must be in the PARK position, and the handmade gearbox is in neutral.
You can not run the engine in the absence of a driver in the cabin, if someone is located in front of or car. The keychain is unacceptable to give to children or persons who can not manage this device. The machine must be in good condition, in its system there must be a sufficient amount of all supplies and fuel.
Keychain management
The laid signaling functions are performed automatically or by key fob signals. Some of them can be changed. The procedure is spelled out in the instructions for the Starline A9 system. Programming the keychain is simply carried out. For this, the device has three buttons. Information is displayed on a liquid crystal display.
Driving a car can be performed by one or more keyfobs. If the main device is lost, you can use the spare console. This is a key chain with buttons that has no information for providing information to the user. With it, you can manage almost all system functions.
If the owners of the car use several keyfobs with the display, then all information about the status of car systems and alarm will be displayed on the device screen from which the command was served.
Purpose buttons
Setting the "Starline A9" keychain with a liquid crystal display is performed using the three buttons on the housing. Their combinations make it possible to manage system functions.
Button I may include the programming command if it is quickly pressing once. Holding her 3 seconds, the driver remotely starts or stops the engine. The user can enable security mode. To do this, with the engine running, this button also holds 3 seconds.
Button II with a short press sets the position of the cursor on the screen. If you hold it 3 seconds, the trunk will open.
Button III also allows you to manage the cursor position when you click. It interrupts key fob alert signals. To do this, it is kept pressed 0.5 seconds. To enable or disable clock setting mode, alarm clock, energy saving, this button hold 3 seconds. If you hold it squeezed for 6 seconds, you can enter the i button programming mode.
Pictures on display
All information about the state of the car and the signaling itself can be viewed on the Starline A9 system display. Icons on the key chain will help to navigate in setup and control modes. The instructions are clearly spelled out which picture corresponds to a function or another.
The indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general view of the device functions. To fully understand the appointment of each of them, you need to carefully examine the instructions.
The first picture that is located on the left corresponds to the anti-label mode. If it is on the display, this command is turned on. Next, the function of the additional channel 3. Moved to the right side, you can see the motor autorun mode in terms of temperature. Next is the function of daily autorun or turn on the an alarm engine. This picture follows the remote switching on or off of the motor.
After that, the modes of silent protection are followed. In this case, confirmation sound signals are not triggered. The following picture corresponds to the protection function with the beep. It goes off at a distance of the shock sensor.
A little more about the picture of the Valet service mode is. It should be displayed a picture of the state of car systems and salon temperature indicators. Next, there is an additional channel 2. Ends the chain of the pictures remote opening of the trunk.
Button I.
The i button on the main keychain is programmed by the user. This can be made an unlimited number of times. Most often it is used to shut down or switch on the security mode in the Starline A9 system. Programming a new keychain is simply performed.
Use the III button to move the cursor over the screen. When the desired mode is selected, for example, the inclusion of the protection function or any other, the movement is stopped. The III button is held for 6 seconds. First, two beeps will sound. Then more 3. Then then button are pressed to activate the selected function.
After such a programming, with a short press of the button I, the previously selected mode will be turned on. To set a new feature for it, again perform the above operation.
Button II.
You can assign a function for a button II. You need to press quickly button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue to move, it will move counterclockwise.
The pictures listed above will be selected one after another. When the cursor comes to the desired program, the movement of the III button is stopped. To execute the selected program, the user presses the ii button.
After 10 seconds after pressing any button, the cursor will return to the original CHECK state. This command controls the condition of the machine and temperature in its cabin. It does not change the status of alarm. Knowing this, the user will not have a question how to see the temperature on the Starline A9 key chain. When operating, it is this team that is the most sought-after.
Installation of watch
Starting to work with the system, you need to know how to set up time on the "Starline A9" key chain. You need to hold the III button until two beeps appear. The clock on the display will flash.
To enlarge the digital value of the clock, minutes, you need to press the i button, and to reduce the II button. The transition from the clock to minutes is carried out by a short press of the III button.
Upon completion of the settings, you need to exit the clock setting mode. To do this, hold the III clad button before the appearance of one beep. According to the manufacturer's instructions, you can set the alarm or timer readings.
Code recording
The driver can independently enter into memory system "Starline A9". Programming the keychain is performed in the protection mode. You can bind up to 4 remotes. This must be done if the alarm for some reason does not see the key fob signal or the machine with the already installed system.
To log in to the programming mode, you must enable ignition. The Valet service button is held before the appearance of four beeps.
First set up the main key chain. It clauses the I and II buttons. For additional remote controls, buttons III and IV are pressed without display. After successfully recording the first keyfob, one siren signal will sound.
For all keyfobs, the same procedure is performed. The interval between the record should not be more than 5 seconds. Otherwise, the programming mode will be completed automatically. Next you need to turn off the ignition. The success of the operation will be confirmed 5 outbreaks overall lights cars.
Engine starting
Many drivers are interested in how to make the car with a keychain. "Starline A9" when connecting alarm involves programming the type of gearbox. If it is manual, when installing a wire loop is cut (as indicated in the instructions). If on the car it costs automatic boxThis element is saved.
The engine type is also set. There are two features of the remote launch of the motor. In the first case, you need to put the cursor on the corresponding icon on the display screen. Then you need to press the II button. Or simply clamping button i for 3 seconds.
With the first attempt to start 3 beeps of sirens, 3 outbreaks of overall lights. The keychain will publish a melodic signal. The icon on the display will burn constantly. You can set the engine warming time.
Reset installations
Sometimes the driver may need information how to reset the Starline A9 keyword settings. Actions are manufactured in a specific sequence. Ignition first turns on. Next, the Valet service button is pressed 10 times. After that, the user turns off the ignition. The entrance to the discharge mode is made if 10 beeps of sirens sound after these manipulations.
The service button must be pressed another 1 time. After that, another siren signal will sound. The driver presses the i button on the main key chain. A short signal will sound. This means that the reset was produced. From the settings mode, the system will automatically come out in 5 seconds. Overall lights flashed 5 times. The keychain will publish a melodic signal.
Having considered the features of the automotive alarm "Starline A9", programming the keyboard you do easily and simply. Before working with equipment, you must read the manufacturer's instructions. This will allow the enjoyed functions fully. If necessary, you can return the system to the factory settings. Control keychain will allow you to use security system The car is comfortable and fully.
Alarm "Starline A9" is very popular with drivers of different cars. The system package includes a detailed instruction. It allows you to connect and configure alarm. The manual also spelled out the principles of system operation. After studying user feedback and the provisions of the instruction, you can highlight the basic principles of working with Starline A9. Programming a keychain will be a simple task. Tips of experienced motorists will allow you to configure quickly. It will give the opportunity to enjoy all options. The alarm can be configured to work in or without autorun mode. The blocking function is also adjusted.
General
"Starline A9", the instruction manual of which requires studying before starting to install the system and programming a key fob, is alarm with remote engine start. It has a double-sided radio channel. Its range on the area without obstacles is 600 m. In the pager mode, this indicator increases by 2 times.
Radio signal coding is dynamic. The choice is carried out on the cursor principle. Each command is controlled by its button. It is displayed on the key fob. The system provides sound and vibrating signals alert.
In addition to the main data on the condition of the car, the keychain shows the user time, the temperature in the cabin, as well as alarm clock.
You can install the presented system on machines with diesel, gasoline or turbocharged engine type. The gearbox can be automatic or manual.
Safety regulations
Using the functions of the remote or automatic engine start, the control of the machine nodes, it is necessary to follow the safety measures to use the Starline A9 system. The instruction manual clearly indicates.
The car is important to park on a well-viewed area. In this case, it must be installed on the parking brake. The automatic transmission lever must be in PARK position, and the handmade gearbox is in neutral.
You can not run the engine in the absence of a driver in the cabin, if someone is located in front of or car. The keychain is unacceptable to give to children or persons who can not manage this device. The machine must be in good condition, in its system there must be a sufficient amount of all consumables and fuel.
Keychain management
The laid signaling functions are performed automatically or by key fob signals. Some of them can be changed. The procedure is spelled out in the instructions for the Starline A9 system. Programming the keychain is simply carried out. For this, the device has three buttons. Information is displayed on a liquid crystal display.
Driving a car can be performed by one or more keyfobs. If the main device is lost, you can use the spare console. This is a key chain with buttons that has no information for providing information to the user. With it, you can manage almost all system functions.
If the owners of the car use several keyfobs with the display, then all information about the status of car systems and alarm will be displayed on the device screen from which the command was served.
Purpose buttons
Setting the "Starline A9" keychain with a liquid crystal display is performed using the three buttons on the housing. Their combinations make it possible to manage system functions.
Button I may include the programming command if it is quickly pressing once. Holding her 3 seconds, the driver remotely starts or stops the engine. The user can enable security mode. To do this, with the engine running, this button also holds 3 seconds.
Button II with a short press sets the position of the cursor on the screen. If you hold it 3 seconds, the trunk will open.
Button III also allows you to manage the cursor position when you click. It interrupts key fob alert signals. To do this, it is kept pressed 0.5 seconds. To enable or disable clock setting mode, alarm clock, energy saving, this button hold 3 seconds. If you hold it squeezed for 6 seconds, you can enter the i button programming mode.
Pictures on display
All information about the state of the car and the signaling itself can be viewed on the Starline A9 system display. Icons on the key chain will help to navigate in setup and control modes. The instructions are clearly spelled out which picture corresponds to a function or another.
The indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general view of the device functions. To fully understand the appointment of each of them, you need to carefully examine the instructions.
The first picture that is located on the left corresponds to the anti-label mode. If it is on the display, this command is turned on. Next, the function of the additional channel 3. Moved to the right side, you can see the motor autorun mode in terms of temperature. Next is the function of daily autorun or turn on the an alarm engine. This picture follows the remote switching on or off of the motor.
After that, the modes of silent protection are followed. In this case, confirmation does not work. The following picture corresponds to the protection function with the beep. It goes off at a distance of the shock sensor.
A little more about the picture of the Valet service mode is. It should be displayed a picture of the state of car systems and salon temperature indicators. Next, there is an additional channel 2. Ends the chain of the pictures remote opening of the trunk.
Button I.
The i button on the main keychain is programmed by the user. This can be made an unlimited number of times. Most often it is used to shut down or switch on the security mode in the Starline A9 system. Programming a new keychain is simply performed.
Use the III button to move the cursor over the screen. When the desired mode is selected, for example, the inclusion of the protection function or any other, the movement is stopped. The III button is held for 6 seconds. First, two beeps will sound. Then more 3. Then then button are pressed to activate the selected function.
After such a programming, with a short press of the button I, the previously selected mode will be turned on. To set a new feature for it, again perform the above operation.
Button II.
You can assign a function for a button II. You need to press quickly button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue to move, it will move counterclockwise.
The pictures listed above will be selected one after another. When the cursor comes to the desired program, the movement of the III button is stopped. To execute the selected program, the user presses the ii button.
After 10 seconds after pressing any button, the cursor will return to the original CHECK state. This command controls the condition of the machine and temperature in its cabin. It does not change the status of alarm. Knowing this, the user will not have a question how to see the temperature on the Starline A9 key chain. When operating, it is this team that is the most sought-after.
Installation of watch
Starting to work with the system, you need to know how to set up time on the "Starline A9" key chain. You need to hold the III button until two beeps appear. The clock on the display will flash.
To enlarge the digital value of the clock, minutes, you need to press the i button, and to reduce the II button. The transition from the clock to minutes is carried out by a short press of the III button.
Upon completion of the settings, you need to exit the clock setting mode. To do this, hold the III clad button before the appearance of one beep. According to the manufacturer's instructions, you can set the alarm or timer readings.
Code recording
The driver can independently enter into memory system "Starline A9". Programming the keychain is performed in the protection mode. You can bind up to 4 remotes. This must be done if the alarm for some reason does not see the key fob signal or the machine with the already installed system.
To log in to the programming mode, you must enable ignition. The Valet service button is held before the appearance of four beeps.
First set up the main key chain. It clauses the I and II buttons. For additional remote controls, buttons III and IV are pressed without display. After successfully recording the first keyfob, one siren signal will sound.
For all keyfobs, the same procedure is performed. The interval between the record should not be more than 5 seconds. Otherwise, the programming mode will be completed automatically. Next you need to turn off the ignition. The success of the operation will confirm 5 outbreaks of the machine lights.
Engine starting
Many drivers are interested in how to make the car with a keychain. "Starline A9" when connecting alarm involves programming the type of gearbox. If it is manual, when installing a wire loop is cut (as indicated in the instruction). If an automatic box is worth a car, this element is saved.
The engine type is also set. There are two features of the remote launch of the motor. In the first case, you need to put the cursor on the corresponding icon on the display screen. Then you need to press the II button. Or simply clamping button i for 3 seconds.
With the first attempt to start 3 beeps of sirens, 3 outbreaks of overall lights. The keychain will publish a melodic signal. The icon on the display will burn constantly. You can set the engine warming time.
Reset installations
Sometimes the driver may need information how to reset the Starline A9 keyword settings. Actions are manufactured in a specific sequence. Ignition first turns on. Next, the Valet service button is pressed 10 times. After that, the user turns off the ignition. The entrance to the discharge mode is made if 10 beeps of sirens sound after these manipulations.
The service button must be pressed another 1 time. After that, another siren signal will sound. The driver presses the i button on the main key chain. A short signal will sound. This means that the reset was produced. From the settings mode, the system will automatically come out in 5 seconds. flare out 5 times. The keychain will publish a melodic signal.
Having considered the features of the automotive alarm "Starline A9", programming the keyboard you do easily and simply. Before working with equipment, you must read the manufacturer's instructions. This will allow the enjoyed functions fully. If necessary, you can return the system to the factory settings. Managing the keychain will allow you to use the car's security system comfortably and fully.
System Starline Twace It can be installed on cars with a voltage of battery 12V and a negative pole on the housing.
The central block is placed in the cabin in a hidden place, preferably under the dashboard - in this case the length of the connecting wires will be minimal. To prevent entering the moisture block, it is recommended to establish it in such a way as to eliminate the flow of water droplets on the wires inside the housing. Secure the block on a flat surface with screw screws or bilateral tape so as to exclude its movement during vibrations.
Module of the transceiver with an antenna fasten on lobby glass The car so that from the antenna to the metal parts of the body was at least 5 cm. In this case, the maximum range of keychains is ensured. Also, when installing, it should be noted that the temperature meter of the cabin is in this module, so the module should be placed as far as possible from heat sources and avoid the sun rays on it. Otherwise, temperature testimony may differ from the real temperature of the cabin.
Remove the engine temperature sensor to secure on the engine housing under one of the M6 \u200b\u200bbolts available on the engine, ensuring good contact with the engine housing. The position of the sensor will determine the correctness of the temperature determination of the engine.
The impact sensor is rigidly fasten in the car, ensuring access to its adjustments.
LED indicator fasten on a prominent place on dashboard.
The Valet service button and the activation mode button set to the hidden, but available to the user.
When installing push-button switches under the hood and in the trunk, check the correctness of their operation. With a closed hood or trunk, the gap between the contacts in the switch should be at least 3 mm. Incorrect installation of push-button switches is often the cause of false alarms.
Conducting the wires as far as possible from the sources of electrical interference of the ignition, high-voltage wires, etc. Note that the wires do not come into contact with the moving parts of the design of the car - pedals, steering traction, etc.
Installation of electrical wiring connections must be made when the car battery is disconnected.
Attention! If the car is equipped with an air cushion or has a coded receiver, when the power is turned off, follow the instruction manual for the car or receiver.
All of all-point connections are performed using soldering and isolate well.
Connect the central unit and other signaling components to connect to cable connectors only after the installation is completed. Installation of alarm Machine in accordance with the connection scheme.
Connecting transceiver
The antenna transceiver module is connected to a five-pin connector located in the central unit under the folding lid, with a cable that is included in the alarm kit.
Connecting a two-level shock sensor
The shock sensor is connected to the central unit using a four-wire cable included in the alarm kit. Power supply (body potential) on the sensor is carried out only in the mode of protection. Sensor sensitivity in levels is regulated by potentiometers on the sensor housing.
Connecting a LED indicator
Connect the LED plug into the two-contact connector, located in the central block under the folding lid.
Connecting the engine temperature sensor
The engine temperature sensor connects to the central unit using a 2-wire cable. One of the cable wires, connect to an orange-gray wire (input of the hood key switch) of the 18-pin connector of the central unit, and connect the second wire to the car housing. Connection polarity is not important. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.
Connecting the 6-pin power connector of the central unit
Red wire (№4) - plus power + 12V, connect to a positive battery terminal.
Blue Wire (# 2) - Output Control Management, Connect the ignition Castle ACC terminal.
Yellow wire (№5) - Exit ignition support # 1, connect to terminal 15 ignition lock.
Green wire (№6) - Exit ignition support # 2. The output algorithm is programmed (Function 7). See "Temporary system work charts when remotely start the engine."
Black and white wire (№3) - the output control of the starter, plug the ignition lock terminal 50/1.
Black and yellow wire (№1) - the output of the starter lock control. Connect after the ignition lock from the starter side, having previously cutting the standard wire that runs from the ignition lock to the starter.
Connecting the 18-pin Central Block Connector
Red wire (№1) - plus power + 12V, connect to a positive battery terminal.
Black wire (№9) - minus power, connect with a car housing, ensuring good contact.
Green-black wire (№10) - Connect to lamps of dimensional lights or rotation pointers. Maximum exit load current 7,5A.
Green-yellow wire (№11) - connect to lamps of overall lights or turning pointers. Maximum exit load current 7,5A.
Gray wire (№13) is a positive output for connecting to siren. Maximum output current 2a.
Blue-black wire (№17) - Connect the doors closed on the housing to the button switches when opening the doors.
Blue-red wire (№7) - plug the doors to a + 12V button switches when opening the doors.
Orange-gray wire (№18) - Connect the hood closer to the hood when opening the hood. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.
Orange-white wire (№8) - Connect the trunk to the housing to the push-button switches when opening the trunk.
Yellow-black wire (№15) - negative yield of an additional channel number 1. The duration of the 1 second control signal. Maximum load current 300mA. The channel can be used to control the solenoid spilling trunk. The connection requires an additional relay. An example of a connection scheme is shown in the figure.
The yellow-red wire (No. 5) is a negative yield of an additional channel number 2. Maximum load current 300mA. The duration of the output signal pulse is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). Channel can be used to control additional equipment car. The connection requires an additional relay.
Yellow-blue wire (№14) - negative yield of an additional channel number 3. Maximum load current 300mA. The duration of the output signal pulse is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). The channel can be programmed to implement the function of two-step unlocking door locks or to control other car devices. The connection requires an additional relay.
Blue wire (№2) - negative yield of an additional channel number 4. Maximum load current 300mA. The channel can be programmed to connect to salon lighting or windows control module. The connection requires an additional relay.
Black and yellow wire (№4) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the protection mode is turned on, the operation of the turbotimer, the activation of the function of anti-grab, activation of the immobilizer. When remote and automatically start in the protection mode, the output is not turned off. It is recommended to use to lock the starter circuit. When connected, an additional relay is required.
Black and white wire (No. 12) - negative output of the status of alarm. Maximum load current 300mA. It can be used to block the engine with normally open (HP) or normal-closed (NZ) work algorithm. The connection requires an additional relay.
Black and Red Wire (No. 3) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the turbotimer and the engine starts. In start mode, it can be used to restore the locked engine circuits.
Orange-purple wire (№16) is a negative input of controlling the status of the parking brake or the pedal of a foot brake. The lack of negative potential on this wire in the security mode will trigger alarm operation, and in the mode of running remotely or automatically engine - the engine stop. An example of a connection scheme is shown in the figure.
Serious-black wire (№6) - input control of the engine operation. Input resistance of at least 100 com. Input sensitivity - 1.0V.
Choosing a way of controlling the engine operation (Connecting a gray-black wire
STARLINE A9 alarm)
Motor Control by Tank
The gray-black wire is connected to the delta. The engine start diagnostics is carried out by changing the frequency of the tip signal. On the correctness of the connection of the black and gray wire, it is possible to judge the duration of the starter after turning off the starter during the engine start and receiving the start confirmation on the alarm key chain.
For proper connection A black and gray wire starter must turn off simultaneously with the start of the engine, regardless of the programmed starter scroll duration.
Motor control over the generator
The gray-black wire is connected to the generator output, which is connected to the lamp on the dashboard. Successful engine launch will be monitored by the presence of a positive voltage + 12V at the output of the generator with the engine running. When the black and gray wire is properly connected, the starter must turn off simultaneously with the start of the engine, regardless of the programmed duration of the starter scroll.
Attention! When a gray-black wire is connected to the generator output, it is used to use the quenching resistor 510 com ... 680 com.
Controlling the engine voltage on-board network
In case of the difficulty of detecting the chains of the band or generator, it is allowed to use the engine start monitoring mode over the on-board network. In this case, the gray-black wire does not connect and it is necessary to isolate it. Start confirmation will occur automatically after starting the engine. The disadvantage of this method of control is the fixed starter time. For proper operation of the starter without a twist, you will need to select the necessary duration, programming the function number 3 to the values \u200b\u200bof 800, 1200, 1800 or 3000 ms.
Connecting the built-in engine lock circuit
Run the chain between the ignition lock and starter. In the chain break, connect the black and white wire of the 6-pin connector from the ignition lock and the black and yellow wire 6-pin connector from the starter side. The maximum current of the built-in lock relay is 40a.
Connecting an external engine lock circuit using conventional relays
Run one of the standard engine start circuits and connect the additional relay into the circuit break. The type of contacts of the NR lock relay (normally open) or NZ (normally closed) is programmed (function 15). Initially, the factory is programmed by the NZ Type of Relay Contacts. An example of a connection scheme of one of the chains is shown in the figure.
Connecting an external engine blocking circuit using a Universal Starline Wireless Lock Set
This method of blocking the engine significantly increases anti-theft alarm properties. To control the module included in the Universal Starline Wireless Lock Kit, use a black and white alarm wire, pre-programmed it on a normally open (HP) type of contacts. Possible engine blocking schemes are given in the installation instructions for installing the Universal Wireless Lock Starline.
Connection to Solenoid Unlocking Trudge
Alarm has an outlet for remote spilling trunk (yellow-black wire). Maximum load Exit - 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connect to salon lighting
An additional alarm channel 2 can be used to connect to the neighbor headlights and the implementation of the "Lightway" function (yellow-red wire). The maximum output load is 300 mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connecting an orange-purple wire on cars with manual and automatic gearbox
On vehicles with manual gearbox, connect this wire to the parking brake button switch, which closes to the housing when the brake is turned on.
On vehicles with automatic gearbox, connect this wire to the brake pedal button closed to + 12V when the brake pedal is pressed.
The alarm has an output that can be used to connect to salon lighting and implementing the function of the "polite illumination of the cabin" (blue wire). The maximum output load is 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connecting to neighbor headlights
Connect to the central locking system
Starline Twage alarm has built-in central lock control relays. Relay contacts are displayed on a 6-pin connector. Load capacity of built-in relay 15a. The duration of control pulses is programmed (Function 9).
Connection CHEMA to the locking system with positive or negative control
Connection CHEMA to two-wire locking system drives
CHEMA connection to a pneumatic locking system
Driver Door Activator Connection Diagram for Door Double-Step
Connection schemes
Connecting the 6-pin motor autorun connector
Greetings, dear readers of the site!
I want to tell you a story about replacing the block for the Starline car alarm.
If briefly, it works, it works, I recommend!
From recently, I started to join me on the main key chain of the alarm, it was sold and triggered one time. It was decided to disassemble and see what happened there.
The autopsy showed that due to the design curve of the buttons and the frequent use of the same button, the legs could not withstand the tension and decided to break away from the board.
The button first soldered at home, was enough for a week. Next was soldered on a soldering station with a special, more solid tin, also had a short time, fell off three weeks later.
so it turned out in the end
This button is just tied to the power on / off, so very necessary. Of course, there is a second, programmable button, with which you can also put on guard, but it is inconvenient.
Therefore, it was decided to purchase the second key chain.
I have a fairly old alarm and the original keyfobs are practically not found, and what can be found is not a fact that it turns out to be the original. + Translate price tag.
The fluid search has shown that there are key rings on Ali, but under different veiled names, it very complicated the search. For example, this seller called her Tamarack, the other was Twace, everything is looking for on the word Starline - with a horse price tag.
Also upset the fact that the keyfobs specifically for StarLine A8 are not only for A9. The officially STARLINE state reports that the key rings are not compatible, but at the same time on the profile forum the people wrote that partially compatible and there may be problems with the key fob in the signaling of the signaling, as well as some functions may not work.
A deeper google led to the conclusion that all the same key chains are compatible and basic functions work.
For A9, the choice is much more diverse (against zero for A8). I came across this lot, the price tag was one of the lowest. Of course, it was embarrassed by a small rating of the seller and a modest assortment in the store, but I took the final decision after reading one of the comments that one buyer was successfully stitched by A8. Mostly all the other reviews are good, it was decided to buy.
I ordered, paid, everything is OK. I sent the seller about the 3rd or 4th day, I don't remember exactly already.
Track with tracking. Delivery on current standards is not fast - exactly a month.
Packaging on a troeuchka, a yellow package, the key chain itself in the puppete package, unreliable however. On the way, all the puppies were pleased with mail employees, while they were thrown by my parcel. Therefore, it was worth packing better, they could have broken the screen.
The seller even put this postcard, signed himself. Again, 5 stars asks.
At the sight of a large similarity with the original, although I also can't know if I have the original, because I received a signal from the car and I don't know anything about her biography.
Differences can be reduced that after all, my key chain from A8, and this one from A9.
The case is absolutely the same, quite a bit deeper than the hole under the button and the buttons themselves are made from another material, slightly larger out of the housing.
Pictograms on the screen are a bit brighter from the new, perhaps on the old one they focused on time.
Illumination of the same color. The resulting keyfob seems a little worse the screen in quality, if you look at the top, then the badges are flexible, the old one was also, but not so much expressed.
In general, more visual differences did not find.
External comparison
Even there is a holographic sticker StarLine :) 
I stitched the key chain with a bang, works as a native. Programmatically distinguished by the A9 key chain from A8 consists only that the cursor of the programmable button 2 over time hesitates to the default position, there was no such thing on the old old one.
I stitched on this instruction:
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
1. Turn the ignition.
2. Press and hold the VALET service button until 4 siren signals appear.
3. To write the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
4. Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
5. Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.
When I stitched new keychain, missed very much important moment, the button then on the old one is broken and it will not work it. Thus, if something went wrong, I would stay without a signal for a while, but everything went like on the oil, the new key chain was lying without any problems. Now it remains to fall the old old and flash it, it will be a spare.
Checked the main functions, accurately work:
- Removal / arming, with sound and without.
- Anxiety on the shock sensor 1 and 2 levels with feedback
- autorun and engine stop.
- Request information about the status of the car (temperature, whether the engine is launched, do the doors, the position of the handbrake, ignition)
- Opening the trunk on the second channel.
In the rest of the functions I do not need, so I did not check.
To whom it is interesting, for comparison, photos of the insides, on top of the old keychain, under it overlooked sabzh.
It can be seen in the naked eye that in the version A8 screen on the loop, in A9 Wpayan on the legs 
Separate fees did not, reluctant to gut a new key chain, but visually there are differences in circuitry 
And again these buttons that, I hope this time stretches for a long time. (Photo after the 3rd propios of the old key fob) 
By the time the review is published, the old keychain was released, the button started again. Both key products have been successfully recorded in the signal of the signal. Unfortunately, they do not work in a pair, that is, when the alarm is triggered, the key chain, from which they put on guard, will be silent. The status of protection does not change dynamically on both keyboards, only on the one from which you install / remove the security.
In general, they work according to the principle - who is the last, that and dad.
The goods are purchased for money and on its own initiative. If someone decides to buy a key chain from this seller, write in the comments, I will try to negotiate a discount for Muskovchan.
For Sim I speak, thanks for watching!
I plan to buy +16. Add to favourites I liked the review +24 +52Operating and Installation Instructions
Mandatory security measures when using the remote or automatic engine launch function.
It must be remembered that the car is a means of increased danger. Section 12.8. rules road Person: "The driver can leave his place or leave the vehicle if they are taken by the necessary measures that exclude spontaneous movement. vehicle or use it in the absence of the driver. "
Before servicing the Starline Twage A9 car alarm, carefully read the measures of safe use of the function of the remote or automatic engine launch set out below.
- Always park a car on an open, well-ventilated area.
- Always put the car on the parking brake, which should be in good condition and eliminate the possibility of moving the car.
- Leaving the car, be sure to install the control lever of the automatic transmission in the PARK position, and the shift lever of the manual gearbox - to the neutral position.
- If a manual gearbox is used in your car, then before turning on the function of the remote or automatic start of the engine, be sure to prepare the procedure for the start of the engine neutral engine.
- Never run the car engine in the absence of a driver if anyone is in front of the car or behind it.
- Never transmit car alarm management tracks to children, as well as other persons without their preliminary familiarization with this Instruction.
- On cars with a manual gearbox, it is not recommended to be remote or automatic starting the engine if the car is outside the visibility zone, and the auto alarm user is not able to control the engine start process.
- Before you include the remote or automatic engine start function:
- make sure in good condition of the car;
- make sure there is enough fuel, oil, coolant, etc.;
- set the operating parameters of the salon heater (air conditioner), glass heating and other accessories for the required levels;
- install a regulator of blowing a salon on air circulation, which will make it possible to warm more efficiently or cool the air in the car.
Technical characteristics of car alarm
| Carrier Control Radio Signal | 433.92 MHz |
| Maximum radius of the main key | 600 m * |
| Maximum radius of pager | 1200 m * |
| Maximum range of additional keychain | 15 m * |
| Type of shock sensor | piezoelectric |
| Working temperature | from -40 to +85 ° С |
| Supply voltage direct current | 9-18V. |
| Current consumed by signaling in security mode | 25ma |
| The maximum allowable current at the outputs: | |
| Sirena connection circuits | 2A. |
| Meat circuits of overall lights | 2x7,5A. |
| Electric Drive Control Chains Door locks | 15A. |
| Ignition switching circuits | 40A. |
| Chains of Inclusion Ass | 40A. |
| Starter switching circuits | 40A. |
| Engine lock circuits | 40A. |
| chains of additional control channels | 300 Ma |
| Food basic keychain | 1.5V (1 AAA Battery) |
| Power supply additional keychain | ZV (1 Battery type CR2032) |
* The range of the keychain and the pager may decrease depending on the place of installation of the transceiver, the location of the car and the user, radio frequency interference, weather conditions, voltage car battery and voltage element of the battery.
STARLINE TWAGE car alarm is allowed to use on the territory of the Russian Federation and meet all requirements. regulatory documents RF.
Life time car alarms Starline The TWAGE installed by the manufacturer is 5 years, provided that they are installed and operated in strict accordance with this instruction.
Possibilities of this car alarm
Protected car zones and ways to protect them
- Engine - from start-up (lock electron)
- Doors, hood, trunk - from opening (push-button switches)
- Parking brake-from shutdown (push-button switch)
- Body, wheels, windows, from shocks and beats (two-level impact sensor)
- Ignition - from inclusion
Auto alarm protection
- Dynamic control code, protected from selection and interception
- Memoring the state when power outages and return to the same condition when recovering nutrition
- Restriction of the number of distress alarm cycles
- Interrupting alarms without shutdown mode
Protective auto alarm functions
- Turn on the alarms when triggered sensors in security mode
- Feed alarm alarm alert
- Remote inclusion of "Panic" regime
- Anti-Frame mode included by remotely keychain
- Immobilizer mode
- Turbotimer mode
- Engine lock and save it when dismantling alarm system
Self-diagnosis and indication of modes of operation
- Automatic control of security sensors with disabling faulty and message about it
- Indication of alarm status LED and on the display keychain
- Indication of the causes of alarm operation for 7 protection zones
- Indication of faulty zone when the protection mode is turned on
- Displaying alarm factory indication by sound signals
- Light outdoor light alarm when the security mode is turned off
- LED indication of the service life switches
Service functions of car alarm
- Silent security mode
- Protection Mode with Operating Engine
- Silent Enable / Off Protection Mode
- Enable protection mode without keychain
- Delay in the inclusion of the regime for the population of the salon light
- Automatic return to the protection mode during accidental shutdown
- Self-diagnostics when the security mode is turned on / off
- in levels of protection
- Remote control of the central lock
- Management of the central lock from the ignition castle
- Two-step unlocking door locks
- Two-pulse unlocking door locks
- The possibility of implementing the "Comfort" function
- 4 additional control channels
- Car Lighting Control
- "Panic" mode
- Car search mode
- Service mode Valet.
- Emergency Disable Protection Mode without a key
- Temperature indication in the car
- Current time indication, timer, alarm clock
- Remote programming of new and erasing of lost key chains
- Remote programming modes and signaling functions
- The ability to reset programmable functions to factory presets
- Power Saving Mode Singling with Liquid Crystal Display
- Call mode from car
Engine start functions
- Remote Start and Engine Warming
- Automatic engine start at temperature, daily timer or alarm
- Remote or automatic stop of the running engine
- Engine type selection: gasoline / diesel
- Transmission type selection: automatic / manual
- Selecting the starter scroll time at startup
- Motor control over the signal of the tank, generator or voltage of the on-board network
- Indication of running time running on the display keychain
- Remote extension of running engine operation
Keychains management
Car alarm performs the functions laid in it or automatically, or by the signals of the keychain when the buttons are pressed. Some of the features provided and some system operation parameters may vary by programming.
Starline Twage auto alarm has a 3-button control key chain with a liquid crystal display. Assign button 1 keychain is programmed. The purpose of the button 2 is selected by quickly moving the cursor on the display of the keychain using the button 3. When you press the keychain buttons for a few seconds, the fluorescent illumination of the display is turned on.
When performing a signaling of the command, the proprietary information is displayed on the display and the melodic beep is fed.
When performing any actions, any action automatically, the corresponding information is also displayed on the display of the keychain and is accompanied by sound signals or vibration.
If more than one keychain is used to control the alarm, then the condition of the car and car alarm will only be displayed on the display of that keychain from which the last command was filed.
In the case of the inoperability or loss of the main keypad with a double-sided connection and a liquid crystal display, the system has an additional 4-button keychain feedback with a standard radius of action. Most functions and operation modes of alarm can be activated from this keychain also, but then the instruction manual is written for the use of the main keypad with the LCD display.
Button 1.
- Programmable Team (0.5 sec)
- Remote Running and Stopping Engine (3 sec)
- Inclusion of the protection mode with the engine running (3 seconds)
Button 2.
- The command corresponding to the current cursor position on the keychain display (0.5 seconds)
- Runger unlocking (3 sec)
Button 3.
- Managing the cursor position on the keyboard display (0.5 seconds)
- Interrupt signals alert keychain (0.5 sec)
- Turning on and off clocking hours, alarm clock, timer, energy saving (3 seconds)
- Programming Button 1 (6 seconds)
1 + 2 buttons
- Search mode (0.5 sec)
- Panic Mode (3 sec)
Buttons 3 + 1
- Select alert mode keychain (0.5 sec)
Buttons 3 + 2
- Fast installation timer keychain (0.5 sec)
The keychain with the LCD is the "aaa" type unit, 1.5V. The battery life depends on the frequency of using the keychain, from the frequency of the pager, from the selected alert mode, on the type of power installed. The capacity of nutrition elements on sale may differ several times. Accordingly, the average operation of one battery keychain can be from 3 to 6 months. When the battery discharge the display shows the icon, which indicates the need to replace the battery keychain. Replacing the battery can be performed by the owner independently in the following order:
- Open the lid on the back of the keychain and remove the old battery.
- Briefly press 1 keychain button.
- Install new batteryBy observing polarity, and close the lid. (The correct position of the battery is indicated on the keychain case under the lid).
- After replacing the battery, adjust the readings of the clock and alarm. Re-programming button 1 keychain is not required.
Button 1.
- Turning on and off protection regime (0.5 sec)
- Channel control №3 (3 sec)
Button 2.
- Running and stopping the engine (0.5 sec)
- Extension of engine operation time (3 sec)
- Inclusion of the protection mode with the engine running (3sek)
Button 3.
- Search mode (0.5 sec)
- Unlocking the trunk - channel number 1 (3 sec)
Button 4.
- Silent switching on and off protection (0.5 sec)
- Channel control №2 (3 sec)
1 + 2 buttons
- Panic Mode (0.5 sec)
1 + 3 buttons
- Turning off the shock sensor (0.5 or 3 seconds)
1 + 4 buttons
- Turning on the service regime (0.5 or 3 seconds)
2 + 3 buttons
- Enable temperature start mode (0.5 or 3 seconds)
2 + 4 buttons
- Enable daily automatic launch mode (0.5 or 3 seconds)
Buttons 3 + 4
- Inclusion of anti-diagnosis mode (0.5 or 3 seconds)
- Record keychain in programming mode (3 sec)
In the four-button keychain without feedback, the CR2032 lithium battery is used, Sv. The battery life of the battery itself also depends on the frequency of using the keychain and on the type of the installed item. When the battery is discharged, it is necessary to replace it. The replacement of the battery must be performed in the following order:
- Unscrew the screw on the bottom of the keychain and open the lid.
- Remove the old battery element and install a new one, observing the polarity.
- Close the keyboard lid and tighten the fastening screw.
Liquid crystal display keychain
Icons with alphabetic designation- indication of commands, modes and signaling functions
- Anti-Frame mode (on / off)
- Additional channel 3 (on / off)
- Resource Auto Tackage Mode (On / Off)
- Daily autorun mode or Starting on alarm (on / off)
- Remote Start / Engine Stop (On / Off)
- Silent protection mode without confirmation sound signals when you turn on / off mode (on / off)
- Sound Signal Protection Mode (ON / OFF)
- Remote shutdown shock sensor
- Service Mode Valet (On / Off)
- Indication of the condition of the car and the temperature of the cabin
- Additional channel 2 (on / off)
- Remote opening trunk
Icons with digital designation- indication of the status of alarm and car
- Indication of the discharged battery keychain
- Activation of additional channel 2
- Temperature autorun mode
- Engine running
- The trunk is open
- Doors are open
- Vibration alert mode
- Service mode Valet.
- Automatic Security Real Mode
- Silent security mode
- Sound Signal Protection Mode
- Hood is open
- Punch on the body (1 or 2 level of impact sensor)
- Parking brake is turned off 15. Door locks
- Unlocking door locks (including when opening doors)
- Standby mode (only the receiver keychain works)
- Team indication by keychain
- Call from car
- Energy saving mode keychain enabled
- Inclusion of ignition
- Enabled alarm clock
- Time of day - PM
- Time of day - am
- Daily autorun mode or start-up
- Indication of time, temperature and autorun mode
- Temperature scale indication (Celsius)
- Reverse Timer Included
Programming button 1 keychain
The purpose of the button 1 keychain is programmed and can change the car owner itself unlimited number. For ease of use, the alarm is recommended to program this button to enable / off the security mode.
Programming is performed in the following order:
In the future, when using alarm, a short press of the 1 button, the keychain will lead to the execution of the command assigned to it (turn on and off the security mode). At the time of pressing the button, the icon corresponding to the programmed function will light up.
Note. To reprogram the purpose of the button 1, you need to do a newly described procedure. The 1 button assignment will be replaced with a new one. Next, the instruction manual is written with the fact that the button 1 is programmed to turn on and off the security mode.
Purpose button 2 keychain
Purpose of the 2 button keychain is determined by the current cursor position on the keyboard display. Moving the cursor is made by pressing the 3 keychain button in the following order:
- Quickly press 3 or more times button to start the cursor movement. Pause and repeated fast press button 3 The keychain changes the direction of movement of the cursor.
- When you press the 3 button, the cursor will cyclically move on the icons indicated by the letters on the display diagram. Sequential press of the 3 button keychain Set the cursor to the position corresponding to the desired command.
The subsequent short press of the 2 button keychain will lead to the execution of the selected command.
Automatic cursor position return to Check command
For ease of use of the keychain and eliminating the accidental inclusion of modes and functions of car alarm after 10 seconds after the last press of the keychain buttons, the current cursor position is automatically returned to the Check command. The Check command monitoring the condition of the car and temperature in the cabin does not change the status of the alarm and is the most frequently used during operation.
Installation of watch readings
For ease of use, the main keychain of the alarm has a built-in clock. To set the clock, press the 3 keychain button and hold down until 2 short beeps appear. The clock indicator will flash.
To increase the readings of the clock, the key 1 button is used, to reduce - button 2 keychain. To quickly increase or reduce the readings of hours, hold down the appropriate keychain button.
To go to the installation of minutes, click the 3 keychain button. To increase the readings, the minutes button is used 1 keychain, to reduce the readings - button 2 keychain. To quickly increase or decrease the readings of minutes, hold down the appropriate keychain button.
To exit the time setting mode, press and hold the 3 button to the key before the appearance of one short beep or wait for the automatic output.
Installation of alarm clock
The alarm keychain has a built-in alarm clock. To set the alarm, press the 3 keychain button and hold down until 2 short beeps appear.
Press the 3 keychain button sequentially before the alarm indicator appears. An alarm clock indicator will flash.
To increase the parameter value, a button 1 is used to reduce the value - button 2. To quickly increase or decrease the value of the parameter value, hold down the appropriate keychain button.
To go to the setup of the alarm minutes, click the 3 keychain button.
After setting the clock values \u200b\u200band the alarm minutes, click the 3 keychain button to set the alarm mode (on-enabled / ff-turned off). To turn on the alarm, press button 1 (indication ON.), to turn off-button 2 (indication Off).
To exit the installation mode, press and hold the 3 button button until a short audio signal appears or wait for automatic exit.
The enabled alarm mode on the display of the keychain is indicated by the icon.
When the alarm is triggered, a melodic signal will sound, it is necessary to press the 3 button for its early interrupt.
Timer Installation
In addition to the clock and alarm, the alarm keychain has a built-in time countdown timer. To set the timer, press the 3 keychain button and hold down until 2 short beeps appear.
Press the 3 keychain button sequentially before the timer indicator appears. Setting time and turn on the timer is made similar to the alarm.
The maximum value of the timer time is 19 hours 59 minutes.
When the timer is turned on, the display shows its current status and flashing indicator. After the set time expires, 8 beeps will follow, and the timer indication will disappear. To interrupt audio signals, you need to press the 3 key button.
Fast installation of timer
To quickly promptly set the timer value, press the buttons 3 and 2 at the same time. A flashing indicator will appear on the display and the timer time value. To change the value, click simultaneously buttons 3 and 2. Possible values \u200b\u200bfor quickly installing the timer - 10 minutes, 20 minutes, 30 minutes, 1 hour, 1 hour 30 minutes, 2 hours.
When the timer is turned on, the display shows its current status and flashing indicator. After the set time expires, 8 beeps will follow, and the timer indication will disappear.
Select alert mode
The control keychain provides 2 alert mode: sound signals or vibration. To select a type of alert signals, press the 3 and 1 buttons at the same time.
When you turn on the vibration alert mode, 2 vibrating signals will follow, the indicator appears on the display.
When the sound alert mode is turned on, a melodic signal will follow, the indicator will disappear.
Note. Next, the instruction manual is written according to the enabled alert mode with sound signals. When the warning mode is enabled, instead of sound signals, the keychain will follow the vibro signals.
Energy saving mode
To increase the battery life of the main keychain, a special power saving mode is provided. In this mode, the keychain is reduced to a minimum after 2 minutes after turning off the alarm protection mode. Reducing consumption occurs due to shutdown electrical circuit Receiver.
To enable power saving mode, you must do the following procedure:
When the power saving mode is enabled on the display, the keychain will constantly display the indicator after 2 minutes after the protection mode is turned off on the display of the keychain goes out the icon, confirming that the power saving mode is activated.
Note: In power saving mode, the receiver keychain will be automatically activated each time for 2 minutes to obtain a confirmation signal on the execution of the command signaling sent from the keychain. For example, if the trunk unlocks the trunk command when the security mode is turned off, the keychain will confirm the execution of the audio signals, after which it will switch to power saving mode.
Enable Sound Signal Protection Mode
Before turning on the security mode, make sure that the ignition is turned off, doors, the hood, the trunk is securely closed, the parking brake is turned on. To activate the security mode, press the 1 keychain button ( button 1 must be programmed to enable / off guard mode).
1 Siren signal and 1 flash of dimensions will confirm the inclusion of the security mode. Automatic locking door locks will occur if they are connected to the alarm. The LED will flash, indicating that the car is guarded.
On the display, the icon will appear on the display and will follow a short beep.
Attention! If the doors, the hood, the trunk will be bad closed, or one of the button switches of doors, the hood, trunk, or the parking brake is not turned on, then the alarm will warn about this 4 siren sound signals and 4 outbreaks of dimensions. See the item "Self-Diagnosis when the protection regime".
Turning on the mode of silent protection
Before turning on the security mode, make sure that the ignition is turned off, doors, the hood, the trunk is securely closed, the parking brake is turned on. To enable silent security mode, set the cursor to the icon and click the 2 keychain button.
1 The outbreak of the dimensions will confirm the inclusion of the security mode. Automatic locking door locks will occur if they are connected to the alarm. The LED will flash, indicating that the car is guarded.
On the display, the icon will display and follow 1 short beep.
Attention! If the doors, the hood, the trunk will be bad closed, or one of the button switches of doors, the hood, trunk, or the parking brake is not turned on, then the alarm will warn about this 4 siren sound signals and 4 outbreaks of dimensions. See the item "Self-Diagnosis when the protection regime".
Inclusion of the protection mode when the engine running
The alarm provides the possibility of incorporating the protection mode when the engine running. It may be necessary with short-term stop. The maximum time during which the engine will operate, is determined by the programmed function number 1.
The protection mode is included in the following order:
Keychain will give 1 short beep. It will display icons on his display, and the current time will be displayed.
After automatic engine stop, the security mode will remain on. The ignition zones and the impact sensor will be taken under protection. LED indicator will flash.
Attention! With simultaneously programmed turbo mode and engine support mode, the SAFE engine function is not available for the engine operation mode. With this condition and the alarms specified in this section will perform the function of the turbotimer. See More Camera Mode. Turbotimer.
Automatic Protection Mode (Programmable Function)
If the function of automatically enable protection mode is programmed, then after turning off the ignition and closing the last door follow 1 Siren signal and 1 flash of dimensions. After 10 seconds, the alarm will automatically turn on the security mode. The inclusion confirmation will be 1 Siren Signal, 1 Sound Sound Sound and 1 Flash Dimensions. Doors locks close. On the display keychain will display icons.
Attention! If one of the door button switches is faulty, the automatic switching on the security mode will not happen (see section "Control of the health of the limit switches").
If the parking brake is not included, then after automatically inclusion of the security mode, 4 beeps and 4 outbursts are followed.
Emergency Enable Protection Mode without a keychain
To include the security mode in emergency cases, for example, when losing or inoperability remote control, it is necessary to do the following:
- Turn on the ignition, without a winding engine.
- Press the service button 8 times.
- Turn off the ignition. The confirmation will follow 1 signal of the siren and 1 outbreak of dimensions.
- For 20 seconds, exit the car and close all doors with the key. First 1 siren signal will follow, then 1 sound keychain.
After 20 seconds after turning off the ignition, regardless of the door state, the system will turn on the security mode. The confirmation will follow 1 outbreak of dimensions. The LED will flash, indicating that the car is guarded.
Attention! If the automatic switching on the security mode is programmed, then after closing the last door first follow the 1 Siren signal, then 1 sounding signal, then 1 additional siren signal and 1 outbreak of dimensions.
If the parking brake is not turned on, then after switching on the security mode, 4 beeps follows and 4 flash outbreaks.
If the security mode is enabled in an emergency (without a keychain), then in case of triggering any of the security sensors, only alarms will follow only the alarms - 4 siren signals and 4 outbreaks of dimensions. Then, if the security mode is not turned off, after 20 seconds it turns on full cycle Alarms.
Delayed sensor activation after the protection mode is turned on (programmable function)
Alarm has the ability to program the delay in activating the sensors after switching on the protection mode 5,15.30 or 45 seconds.
This delay may be necessary to bypass the door zone at the time of the smooth outset of the cabin light of the car or to calm the shock and volume sensors. When you turn on the mode of protection by keychain, the engine is blocked instantly. Automatic locking locks will occur if they are connected to the alarm.
After the programmed delay time expires, 1 outbreak of the dimensions follows, after which the zones of the end switches of doors, the hood, trunk and sensors are taken under protection. If at this moment the door zone still turns out to be open, then the alarm cycle will follow. When open hood or the trunk at the time of the expiration of the delay, these zones will be temporarily excluded from the security circuit. The warning signals of poorly closed hood or trunk follow immediately at the time of the protection mode.
Self-diagnosis when the protection regime is on
If, when you turn on the security mode, 4 siren signals and 4 flashes of dimensions appear, which means that the doors, the hood, the trunk can be badly closed, one of the key button switches of doors, hood, trunk or the parking brake is not turned on. The keychain will give 4 short beeps, and a faulty zone will appear on the display. This zone will be temporarily excluded from the security circuit. An open door indication is simultaneously accompanied by display icons.
It is necessary to close the doors, the hood and trunk, turn on the parking brake, and the system will automatically take this zone under protection. The confirmation will follow a short beeping keychain, the image of a faulty zone will go out on the display. In order for in the protection mode, the icon is displayed. You must turn off and re-enable the protection mode with normally closed doors.
If the reason for the malfunction of the push-button switches cannot be eliminated on the spot, the system will turn on the protection mode by bypassing the faulty zone. In the case of spontaneous troubleshooting, when the mode is enabled, the alarm will automatically automatically take this zone under protection.
Turning off the security of confirmation sound signals
To turn off the security mode with sound signals, press the 1 keychain button ( button 1 must be programmed to enable / off guard mode).
If in the protection mode did not occur alarm operation, only a shock sensor was triggered, then 2 siren signals and 2 outbreaks of dimensions will confirm the protection of the protection mode. Automatic unlocking door locks and the inclusion of the cabin light will occur if they are connected to the alarm. Engine lock will turn off. The LED indicator goes out.
The icon will appear on the keyboard display, and 2 sounding beeps will follow.
Attention! If, when the security mode is turned off, 4 beeps and 4 flash of dimensions are followed, this means that security sensors have been triggered in the protection mode. See the item "Self-Diagnosis When the Security Mode is turned off."
Silent Protection Mode
To turn off the security mode without confirmation sound signals, set the cursor to the icon and click 2 keychain.
2 flashes of dimensions will confirm the protection of the security mode. Automatic unlocking door locks and the inclusion of the cabin light will occur if they are connected to the alarm. Engine lock will turn off. The LED indicator goes out.
The icon appears on the keyboard display, and 2 short beeps will follow.
Attention! If, when you turn off the security mode, you follow 4 beeps of the keychain and 4 flashes of dimensions, which means that security sensors have been triggered in the protection mode. See the item "Self-Diagnosis When the Security Mode is turned off."
Turning off the security mode when the engine running
To turn off the security mode when the engine running briefly press the 1 keyword button. 2 siren signals and 2 flash outbreaks will be confirmed off. Automatic unlocking door locks will occur if they are connected to alarm. The engine continues to work.
On the display, the icons will appear 2 short beeps.
Emergency shutdown of security regime
For emergency shutdown Protection modes, for example, during the loss or inoperability, the remote control keychain is necessary:
- Open the car door, the alarm will turn on the alarms.
- Turn on the ignition, not a winding engine.
- For 20 seconds, press the service button 4 times.
- Turn off the ignition. The confirmation will follow 2 signal sirens and 2 outbreaks of dimensions, the protection mode will turn off.
Attention! If the automatic security mode function is programmed, then after executing item 4, turn on the ignition for no less than 10 seconds, then turn off. Otherwise, the system will turn on the protection mode again.
Automatic return to the protection mode during accidental shutdown (programmable function)
If within 30 seconds after turning off the vehicle's door protection mode, the alarm will automatically turn on the protection mode. It protects from shutting down the protection mode by accident by pressing the keychain button, as well as if you, turning off the alarm, change your intention to sit in the car, and turn on the security mode will forget. Alarm will turn on the security mode yourself.
If the security mode was turned off with sound confirmation signals, the security mode translate is confirmed by 1 short beep and 1 flash of dimensions. On the display, the keychain will display icons, and. 1 short beep will follow.
If the protection mode was turned off silently, the conversion of the security mode is confirmed only by 1 flash of dimensions. On the display, the icon will appear on the display, and 1 short beep will follow.
Automatic locking door locks will occur if they are connected to the alarm. The engine will be blocked. The LED will flash, indicating that the car is guarded.
Self-diagnosis when the protection mode is turned off
If the alarms appeared in the security mode as a result of the triggering of the door zone, the hood, trunk, turn on the ignition or turn off the manual brake, and the alarms were not interrupted from the keychain, then when the security mode is turned off, 4 beeps follow 4 sound signals and 4 outbreaks. On the display, the icons corresponding to the reasons for the alarm response will display.
If the alarms were interrupted with a keychain, then when the security mode is turned off, only 2 sound signals and 2 flash of dimensions will follow. In this case, on the display, the indication of the indication of the causes of the alarm response will not follow.
Protective functions
Alarms
If in the security mode there will be a trigger of any of the security sensors, it will cause it automatic inclusion Alarms: Siren sound signals, flashing overall lights and inclusion of salon light; The engine will be blocked. The keychain will serve sound alarms, and the display shows the reason for the alarm operation. During the sound of the signaling sirens on the display will flash the icon; While the dimensions are blinking, the headlights of the car will flash on the display.
Alarms are fed by cycles. The duration of one alarm cycle and the maximum possible number of cycles for various causes of signaling is listed in the table.
If, after the end of the alarm cycle, the reason for the signaling is not eliminated (for example, the doors remained open), then the corresponding security area is temporarily excluded from the security circuit until the cause of the cause of the trigger (before closing doors), but on the display keychain continues.
| Reason anxiety | Icon on display | Duration of one alarm cycle | Max, the number of cycles with a constantly triggering sensor | Max, number of cycles with a periodically triggering sensor |
|---|---|---|---|---|
| 1 Strop Sensor Level | 3 Flash Signals | 8 in a row | 8 in a row | |
| 2 Start Sensor Level | 20 sec. sound 20 sec. shine |
8 in a row | 8 in a row | |
| Doors | 30 sec. sound 35 seconds. shine |
1 | 3 | |
| Hood | 30 sec. sound 35 seconds. shine |
1 | 3 | |
| Trunk. | 30 sec. sound 35 seconds. shine |
1 | 3 | |
| Ignition | 30 sec. sound 35 seconds. shine |
4 in a row | 3 | |
| Parking brake | 30 sec. sound 35 seconds. shine |
1 | 3 |
Note. If an interruption of alarms with a keychain occurred, then the number of alarm cycles with a periodically triggering sensor begins again.
If there is no silent security mode, then when the alarm signal is triggered, the alarms will not follow.
Interrupt alarm alarm
If you want to interrupt the alarms without turning off the security mode, for example, you checked the operation of the sensors, press the 1 keychain button. In this case, the alarm will remain in the mode of protection.
If, at the time of interrupting alarm, the reason for the operation of the alarm was eliminated, then the sound signals and the indication on the display the keychain will stop.
If at the time of interruption alarm, the reason for the signaling will not be eliminated, then the corresponding icon will be displayed on the display. The security zone will be temporarily excluded from the security circuit. The icon on the display will go out only after eliminating the cause of the triggering, 1 short beep sounds to confirm.
For interrupting only alert signals, press the 3 keychain button. At the same time, alarm alarm signals and display on the display keychain will continue.
Remote Alarms (Panic Function)
To enable the "Panic" mode, when the ignition is turned off, press and hold the 1 and 2 keychain buttons for 3 seconds.
3 sound signals are followed by sirens and 3 outbreaks of dimensions. The keychain will give a beep.
If the security mode was pre-turned off, then when the "Panic" mode is turned on, the door locks are locked. After turning off the "Panic" mode, the security mode automatically turns on. In this case, the display on the display does not follow.
Anti-Frame mode included by keychain
To turn on the anti-label mode, move the cursor to the icon using the 3 keychain button and when the engine is running (Ignition Enabled), click the 2 keyword button.
The alarm will first turn on the 30-second warning lights, then the audio and light alarms and sound signals are turned on. Doors locks will close, and the engine will be blocked.
On the display keychain will flash the icon
Anti-Frame mode included with a special button
When the engine is running, press the special button to turn on the anti-label mode. The dimensions will flash for 30 seconds, then the 30-second alarms and sound signals are activated, the engine (starter circuit) is locked. On the display keychain will flash the icon
To turn off the anti-label mode in the first 30 seconds, press and hold the special button until 3 siren signals or a melodic keychain appears. Light signals will stop.
To turn off the anti-label mode after 30 seconds, set the cursor to the icon and when the ignition is turned off sequentially with the interval of 3-5 seconds, press the 2 keychain button, then the 1 keychain button. Alarms will stop, the engine is unlocked. Display on the display keychain will stop.
Immobilizer mode (programmable function)
If the immobilizer mode is programmed, the engine will be automatically blocked after 30 seconds after each ignition shutdown, regardless of whether the security mode turned on or not. In immobilizer mode, the LED indicator is constantly lit.
To turn off the immobilizer mode, press the 1 keychain button. Follow 2 outbreaks of dimensions and 2 beeps of the keychain. The LED indicator goes out.
Note. If the turbotimer function is programmed, the immobilizer mode will not be turned on.
Engine lock
Reliable engine blocking is maintained during the entire protection period. Attempts of hijackers to start the engine, despite the alarms, will be useless. Even when the central alarm unit is detected and its shutdown from the cable connectors will remain blocked.
Signal protection from power outage
Any attempt of the hijackers turn off the security mode by temporary power outage will be unsuccessful. When the power is turned off, such as reset the battery terminal, the alarm is remembered. When the power is restored, the alarm will again turn out to be in the same mode (see the status table below), the keychain will give a melodious beep.
If a siren with autonomous power is connected to the system, then when the siren battery terminal turns on the alarms.
Service functions
Remote shutdown shock sensor
In the alarm, it is possible to remotely disconnect / turn on the impact sensor over the levels an unlimited number of times during the same protection cycle.
If you need to disable only the preliminary level of the shock sensor, set the cursor to the icon, press the 2 button once. An additionally icon will be displayed on the display display, the 2 siren signals and a melodic signal keychain will be displayed. The first level of the sensor will be disconnected. If you need to turn off both levels of the shock sensor, set the cursor to the icon and click 2 keyword the second time. On the display keychain display icon
Automatic control of the central lock from the ignition key (programmable function)
At your request, the automatic door lock control function can be entered when the ignition is turned on and off. If this function is turned on, then when the ignition is turned off, the door locks will be automatically open.
You can program 3 castle control options when the ignition is turned on:
- castles are not locked;
- locked after 10 seconds after the ignition is turned on;
- locked 30 seconds after switching on the ignition.
Attention! If one of the doors is open at the moment of inclusion of ignition or after switching on the ignition within 10 or 30 seconds, the locking of the door locks will not occur.
Car search mode
To search for your car in the parking lot in dark time Tap simultaneously buttons 1 and 2 keychain.
If before that, the protection mode turned on or turned off with sound signals of confirmation, 6 siren signals and 6 outbreaks of dimensions follow. If the protection mode turned on or turned off silently, only 6 outbreaks of dimensions will follow.
In both cases, a melodic signal keychain will sound.
Call from car
To serve a call signal from the car to the alarm keychain, press the button located on the case of the transceiver module. 6 outbreaks of dimensions follow (2 series of 3 flash). The icon appears on the keyboard display, and 20-second call sound signals are turned on. To interrupt the signals and display on the display, press the 3 keychain button.
Turbotimer Mode (Programmable Function)
For turbocharged machines, a special turbotimer mode is provided, which allows you to keep the engine operation after turning off the ignition with the key for some time required to complete the turbine stop. Thanks to this algorithm, the resource of the turbine sliding bearings is preserved.
The duration of the turbotimer is programmed 1, 3 or 6 minutes. If during operation of the turbo mode, accompanied by the lighting of the LED indicator, the protection mode will be turned on with locking locking locks, then the system will turn off the ignition inputs and the shock sensor during the turbotimer. Engine locking will not happen. The engine will be stopped automatically, and the ignition zones and the impact sensor will be protected only after turning off the turbotimer mode. The LED will start slowly flashed.
Attention.
Control service life switches
In the alarm, it is possible to control the health of the end switches of the doors, the hood and trunk when the security mode is turned off. Opening the doors, hood and trunk when the ignition is turned on, must be accompanied by flashes of the LED indicator. If the LED does not light up when they open, it means that the corresponding terminal switch is faulty.
Monitoring the condition of the car and temperature in the cabin
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow. On the display, the temperature is displayed in the car's cabin and the status of the alarm protection mode, the melodic signal will sound.
Note. The temperature displayed on the display of the keychain may differ from the real temperature in the cabin as it depends on the installation site in the car of the transceiver module (for example, when the module is in the sun, the indicator temperature value will be more real).
Service mode Valet.
To temporarily disable anti-theft and security functions of car alarm, for example, when transferring a car to the station service for prophylactic or repair work It is recommended to enable the service mode Valet.
Before switching on the VALET mode, make sure that the previously programmed modes of the turbotimer and the immobilizer are turned off. Otherwise, enter the function of programming functions and parameters of the alarm and switch the specified modes to the state - disabled.
To enable the service mode, set the cursor to the icon and click 2 keychain. The confirmation will follow 4 of the siren signals, 4 outbreaks of dimensions and sound a melodic signaling signal. A flashing icon appears on the display, when the Valet mode is enabled, only the remote control function of the locking and unlocking the locks of the door and control of the additional channel No. 1 (unscrupping trunk) continues.
To turn off the service mode, set the cursor to the icon, press the 2 keychain button. keychain The confirmation will follow 3 Siren Signals, 3 outbreaks of dimensions and a melodic keychain signal. Icon goes out. If necessary, program the disconnected modes of the turbotimer and the immobilizer again.
Control of additional channel number 1 (remote spilling trunk)
Channel number 1 (yellow-black wire) It can be activated independently of the system of the system and used for remote spilling of the trunk. If the channel is activated when the protection mode is enabled, the trunk zones and the shock sensor are temporarily disconnected.
There are two options for the inclusion of an additional channel number 1:
Option 1 - Press and hold the 2 keychain button for 3 seconds.
Option 2. - Use the 3 keychain button to set the cursor to the icon and press the 2 keychain button.
The confirmation will follow 3 outbreaks of dimensions and 3 beeps of the keychain.
When the security mode is turned off, the flashing image will appear on the display. open trunk.
With the mode of protection on the display, the keychain will appear flashing images of an open trunk and a disabled shock sensor
At the output of the channel there will be a negative impetus with a duration of 1 second - the trunk will open. If, when you activate the channel, the trunk will not open, then the indications of the open trunk and the disabled shock sensor on the display the keychain will not follow.
If at the time of the trunk closing the alarm will be in the mode of protection, then the zones of the trunk and the impact sensor will be taken under protection again after 5 seconds. The confirmation will sound 1 Siren Signal and 1 Sound Sound. Flashing outdoor trunk icons and shock sensor will disappear.
Control of additional channel number 2 (programmable function)
An additional channel number 2 (yellow-red wire) can be activated regardless of the status of the protection mode by 0.8, 10, 30 seconds or before switching off by the keychain. The duration of the output signal is programmed when the system is set (Function 4). The channel can be used to remotely control the additional car equipment.
