Home Rack Programming the STARLINE A9 keyword. Instructions for use and installation of SRARLINE A9 car alarm. Control of the engine voltage onboard network

Rack

Programming the STARLINE A9 keyword. Instructions for use and installation of SRARLINE A9 car alarm. Control of the engine voltage onboard network

Greetings, dear readers of the site!
I want to tell you a story about replacing the block for the Starline car alarm.
If briefly, it works, it works, I recommend!

From recently, I started to join me on the main key chain of the alarm, it was sold and triggered one time. It was decided to disassemble and see what happened there.
The autopsy showed that due to the design curve of the buttons and the frequent use of the same button, the legs could not withstand the tension and decided to break away from the board.
The button first soldered at home, was enough for a week. Next was soldered on a soldering station with a special, more solid tin, also had a short time, fell off three weeks later.

so it turned out in the end

This button is just tied to the power on / off, so very necessary. Of course, there is a second, programmable button, with which you can also put on guard, but it is inconvenient.
Therefore, it was decided to purchase the second key chain.
I have a fairly old alarm and the original keyfobs are practically not found, and what can be found is not a fact that it turns out to be the original. + Translate price tag.
The fluid search has shown that there are key rings on Ali, but under different veiled names, it very complicated the search. For example, this seller called her Tamarack, the other was Twace, everything is looking for on the word Starline - with a horse price tag.

Also upset the fact that the keyfobs specifically for StarLine A8 are not only for A9. The officially STARLINE state reports that the key rings are not compatible, but at the same time on the profile forum the people wrote that partially compatible and there may be problems with the key fob in the signaling of the signaling, as well as some functions may not work.
A deeper google led to the conclusion that all the same key chains are compatible and basic functions work.

For A9, the choice is much more diverse (against zero for A8). I came across this lot, the price tag was one of the lowest. Of course, it was embarrassed by a small rating of the seller and a modest assortment in the store, but I took the final decision after reading one of the comments that one buyer was successfully stitched by A8. Mostly all the other reviews are good, it was decided to buy.

I ordered, paid, everything is OK. I sent the seller about the 3rd or 4th day, I don't remember exactly already.
Track with tracking. Delivery on current standards is not fast - exactly a month.

Packaging on a troeuchka, a yellow package, the key chain itself in the puppete package, unreliable however. On the way, all the puppies were pleased with mail employees, while they were thrown by my parcel. Therefore, it was worth packing better, they could have broken the screen.

The seller even put this postcard, signed himself. Again, 5 stars asks.

At the sight of a large similarity with the original, although I also can't know if I have the original, because I received a signal from the car and I don't know anything about her biography.
Differences can be reduced that after all, my key chain from A8, and this one from A9.
The case is absolutely the same, quite a bit deeper than the hole under the button and the buttons themselves are made from another material, slightly larger out of the housing.
Pictograms on the screen are a bit brighter from the new, perhaps on the old one they focused on time.
Illumination of the same color. The resulting keyfob seems a little worse the screen in quality, if you look at the top, then the badges are flexible, the old one was also, but not so much expressed.
In general, more visual differences did not find.

External comparison

Even there is a holographic sticker StarLine :)

I stitched the key chain with a bang, works as a native. Programmatically distinguished by the A9 key chain from A8 consists only that the cursor of the programmable button 2 over time hesitates to the default position, there was no such thing on the old old one.

I stitched on this instruction:
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
1. Turn the ignition.
2. Press and hold the VALET service button until 4 siren signals appear.
3. To write the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
4. Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
5. Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.

When I stitched new keychain, missed very much important moment, the button then on the old one is broken and it will not work it. Thus, if something went wrong, I would stay without a signal for a while, but everything went like on the oil, the new key chain was lying without any problems. Now it remains to fall the old old and flash it, it will be a spare.

Checked the main functions, accurately work:
- Removal / arming, with sound and without.
- alarm on the shock sensor 1 and 2 levels with feedback
- autorun and engine stop.
- Request information about the status of the car (temperature, whether the engine is launched, do the doors, the position of the handbrake, ignition)
- Opening the trunk on the second channel.
In the rest of the functions I do not need, so I did not check.

To whom it is interesting, for comparison, photos of the insides, on top of the old keychain, under it overlooked sabzh.

It can be seen in the naked eye that in the version A8 screen on the loop, in A9 Wpayan on the legs

Separate fees did not, reluctant to gut a new key chain, but visually there are differences in circuitry

And again these buttons that, I hope this time stretches for a long time. (Photo after the 3rd propios of the old key fob)

By the time the review is published, the old keychain was released, the button started again. Both key products have been successfully recorded in the signal of the signal. Unfortunately, they do not work in a pair, that is, when the alarm is triggered, the key chain, from which they put on guard, will be silent. The status of protection does not change dynamically on both keyboards, only on the one from which you install / remove the security.
In general, they work according to the principle - who is the last, that and dad.

The goods are purchased for money and on its own initiative. If someone decides to buy a key chain from this seller, write in the comments, I will try to negotiate a discount for Muskovchan.

For Sim I speak, thanks for watching!

I plan to buy +16. Add to favourites I liked the review +24 +52

Starline Twace A9. - Automobile security complex with a 2-sided communication radio channel and remote engine start. Communication range in open area - 600m with keychain and 1200m in pager mode. Coding of control radio signals dynamic.

System Starline Twage A9. It can be installed on cars with a gasoline, diesel or turbocharged engine, with an automatic or manual gearbox.

Starting the engine can be carried out by a command of the keychain, on the temperature sensor installed on the engine housing, in time every 24 hours and at any time of the day. Control over the operation of the engine can be carried out by the signal signals, generator or by changing the on-board network voltage.

In alarm Starline Twage A9. The temperature determination function in the passenger compartment is preserved, the second temperature sensor is set to the alarm transceiver, which is usually attached to the windshield or installed under the torpedo. For many owners of Star Line systems, it has already become a habit to communicate with your car, sending him a Check team. In response, in addition to full information about the enabled mode of protection and the state of the sensors, the temperature in the car is displayed on the display. For example, in the summer, seeing that the temperature in the cabin rises above the laid, you can remotely start the engine, and therefore air conditioning, for air conditioning.

Description:

feedback
engine starting
trinket remote control Included 1.
keychain-pager with LCD display included 1
the remote module is to increase the connection radius.
communication module included
consemist included 1
valet switch button included
anti-Hi-Jack switch button complete
vibrating alerts on the pager key chain
maximum radius of the pager channel 1200 meter
maximum range of block channel D / U 600 meters
valet mode
"Panic" mode
passive immobilizer mode is programmed
personal PIN emergency shutdown code
disconnecting sensors when arming
disabling the warning zone of sensors when arming
finding a car in the parking lot
active Anti-Hi-Jack
passive Anti-Hi-Jack
bypassing a faulty zone
entry for an additional sensor
hood / trunk entrance / trunk
number of engine locks 1
external Engine Lock Relay 1
programmable engine lock (NZ or but) 1
pulse duration for electric locks 0.8 seconds.
pulse duration for pneumatic locks 3.6 sec.
other possible centerpieces management pulses (open / close) 0.8-2x0.8 / 0.8-30 seconds.
exit to dimensions 2
exit to the trunk lock is programmed
fM Managing Code Type
output of the control of El Doors of the Power
number of extra beds 4
additional channel I 1 sec.
additional channel II 0.8 / 10/130 / Latch sec.
additional channel III 0.8 / 10/130 / Latch sec.
additional channel IV salon. Changing / Flods. sec.
comfort mode is programmed
mode "Turbotimer" 1/3/6 min.
running the engine by timer 24 hours
running the engine at -5 / -10 / -15 / -20 degrees.
the program "Neutral" for MCPP is
starter start delay for diesel 4/6/10 seconds.
starter time when starting the engine 0.8 / 1.2 / 1.8 / 3 sec.
engine warming time after starting 10/20 / 30 / without limit min.
Starline A9 equipment:
Control block
Feedback key chain with LCD
Keychain without feedback
Stroke 2-level shock sensor
Engine temperature sensor
Antenna module
Kontevik Kapota
LED indicator
Service Button Valet.
Anti-Hi-Jack mode mode
Wire set
Instructions for installation and operation in Russian
Color memo user car alarm Starline. A9.

Alarm "Starline A9" is very popular with drivers different cars. The system package includes detailed instructions. It allows you to connect and configure alarm. The manual also spelled out the principles of system operation. After studying user feedback and the provisions of the instruction, you can highlight the basic principles of working with Starline A9. Programming a keychain will be a simple task. Tips of experienced motorists will allow you to configure quickly. It will give the opportunity to enjoy all options. The alarm can be configured to work in or without autorun mode. The blocking function is also adjusted.

General

"Starline A9", the instruction manual of which requires studying before starting to install the system and programming a key fob, is alarm with remote engine start. It has a double-sided radio channel. Its range on the area without obstacles is 600 m. In the pager mode, this indicator increases by 2 times.

Radio signal coding is dynamic. The selection of control commands is carried out on the cursor principle. Each command is controlled by its button. It is displayed on the key fob. The system provides sound and vibrating signals alert.

In addition to the main data on the condition of the car, the keychain shows the user time, the temperature in the cabin, as well as alarm clock.

You can install the presented system on machines with diesel, gasoline or turbocharged engine type. The gearbox can be automatic or manual.

Safety regulations

Taking advantage of remote or automatic launch Engine, managing machine nodes, it is necessary to follow the safety measures to use the Starline A9 system. The instruction manual clearly indicates.

The car is important to park on a well-viewed area. In this case, it must be installed on the parking brake. Lever arm automatic transmission Must be in the PARK position, and the handmade gearbox is in neutral.

You can not run the engine in the absence of a driver in the cabin, if someone is located in front of or car. The keychain is unacceptable to give to children or persons who can not manage this device. The machine must be in good condition, in its system there must be a sufficient amount of all supplies and fuel.

Keychain management

The laid signaling functions are performed automatically or by key fob signals. Some of them can be changed. The procedure is spelled out in the instructions for the Starline A9 system. Programming the keychain is simply carried out. For this, the device has three buttons. Information is displayed on a liquid crystal display.

Driving a car can be performed by one or more keyfobs. If the main device is lost, you can use the spare console. This is a key chain with buttons that has no information for providing information to the user. With it, you can manage almost all system functions.

If the owners of the car use several keyfobs with the display, then all information about the status of car systems and alarm will be displayed on the device screen from which the command was served.

Purpose buttons

Setting the "Starline A9" keychain with a liquid crystal display is performed using the three buttons on the housing. Their combinations make it possible to manage system functions.

Button I may include the programming command if it is quickly pressing once. Holding her 3 seconds, the driver remotely starts or stops the engine. The user can enable security mode. To do this, with the engine running, this button also holds 3 seconds.

Button II with a short press sets the position of the cursor on the screen. If you hold it 3 seconds, the trunk will open.

Button III also allows you to manage the cursor position when you click. It interrupts key fob alert signals. To do this, it is kept pressed 0.5 seconds. To enable or disable clock setting mode, alarm clock, energy saving, this button hold 3 seconds. If you hold it squeezed for 6 seconds, you can enter the i button programming mode.

Pictures on display

All information about the state of the car and the signaling itself can be viewed on the Starline A9 system display. Icons on the key chain will help to navigate in setup and control modes. The instructions are clearly spelled out which picture corresponds to a function or another.

The indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general view of the device functions. To fully understand the appointment of each of them, you need to carefully examine the instructions.

The first picture that is located on the left corresponds to the anti-label mode. If it is on the display, this command is turned on. Next, the function of the additional channel 3. Moved to the right side, you can see the motor autorun mode in terms of temperature. Next is the function of daily autorun or turn on the an alarm engine. This picture follows the remote switching on or off of the motor.

After that, the modes of silent protection are followed. In this case, confirmation sound signals are not triggered. The following picture corresponds to the protection function with the beep. It goes off at a distance of the shock sensor.

A little more about the picture of the Valet service mode is. It should be displayed a picture of the state of car systems and salon temperature indicators. Next, there is an additional channel 2. Ends the chain of the pictures remote opening of the trunk.

Button I.

The i button on the main keychain is programmed by the user. This can be made an unlimited number of times. Most often it is used to shut down or switch on the security mode in the Starline A9 system. Programming a new keychain is simply performed.

Use the III button to move the cursor over the screen. When the desired mode is selected, for example, the inclusion of the protection function or any other, the movement is stopped. The III button is held for 6 seconds. First, two beeps will sound. Then more 3. Then then button are pressed to activate the selected function.

After such a programming, with a short press of the button I, the previously selected mode will be turned on. To set a new feature for it, again perform the above operation.

Button II.

You can assign a function for a button II. You need to press quickly button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue to move, it will move counterclockwise.

The pictures listed above will be selected one after another. When the cursor comes to the desired program, the movement of the III button is stopped. To execute the selected program, the user presses the ii button.

After 10 seconds after pressing any button, the cursor will return to the original CHECK state. This command controls the condition of the machine and temperature in its cabin. It does not change the status of alarm. Knowing this, the user will not have a question how to see the temperature on the Starline A9 key chain. When operating, it is this team that is the most sought-after.

Installation of watch

Starting to work with the system, you need to know how to set up time on the "Starline A9" key chain. You need to hold the III button until two beeps appear. The clock on the display will flash.

To enlarge the digital value of the clock, minutes, you need to press the i button, and to reduce the II button. The transition from the clock to minutes is carried out by a short press of the III button.

Upon completion of the settings, you need to exit the clock setting mode. To do this, hold the III clad button before the appearance of one beep. According to the manufacturer's instructions, you can set the alarm or timer readings.

Code recording

The driver can independently enter into memory system "Starline A9". Programming the keychain is performed in the protection mode. You can bind up to 4 remotes. This must be done if the alarm for some reason does not see the key fob signal or the machine with the already installed system.

To log in to the programming mode, you must enable ignition. The Valet service button is held before the appearance of four beeps.

First set up the main key chain. It clauses the I and II buttons. For additional remote controls, buttons III and IV are pressed without display. After successfully recording the first keyfob, one siren signal will sound.

For all keyfobs, the same procedure is performed. The interval between the record should not be more than 5 seconds. Otherwise, the programming mode will be completed automatically. Next you need to turn off the ignition. The success of the operation will confirm 5 outbreaks of the machine lights.

Engine starting

Many drivers are interested in how to make the car with a keychain. "Starline A9" when connecting alarm involves programming the type of gearbox. If it is manual, when installing a wire loop is cut (as indicated in the instructions). If on the car it costs automatic boxThis element is saved.

The engine type is also set. There are two features of the remote launch of the motor. In the first case, you need to put the cursor on the corresponding icon on the display screen. Then you need to press the II button. Or simply clamping button i for 3 seconds.

With the first attempt to start 3 beeps of sirens, 3 outbreaks of overall lights. The keychain will publish a melodic signal. The icon on the display will burn constantly. You can set the engine warming time.

Reset installations

Sometimes the driver may need information how to reset the Starline A9 keyword settings. Actions are manufactured in a specific sequence. Ignition first turns on. Next, the Valet service button is pressed 10 times. After that, the user turns off the ignition. The entrance to the discharge mode is made if 10 beeps of sirens sound after these manipulations.

The service button must be pressed another 1 time. After that, another siren signal will sound. The driver presses the i button on the main key chain. A short signal will sound. This means that the reset was produced. From the settings mode, the system will automatically come out in 5 seconds. Overall lights flashed 5 times. The keychain will publish a melodic signal.

Having considered the features of the automotive alarm "Starline A9", programming the keyboard you do easily and simply. Before working with equipment, you must read the manufacturer's instructions. This will allow the enjoyed functions fully. If necessary, you can return the system to the factory settings. Managing the keychain will allow you to use the car's security system comfortably and fully.

Alarm "Starline A9" is very popular with drivers of different cars. The system package includes a detailed instruction. It allows you to connect and configure alarm. The manual also spelled out the principles of system operation. After studying user feedback and the provisions of the instruction, you can highlight the basic principles of working with Starline A9. Programming a keychain will be a simple task. Tips of experienced motorists will allow you to configure quickly. It will give the opportunity to enjoy all options. The alarm can be configured to work in or without autorun mode. The blocking function is also adjusted.

General

Radio signal coding is dynamic. The choice is carried out on the cursor principle. Each command is controlled by its button. It is displayed on the key fob. The system provides sound and vibrating signals alert.

In addition to the main data on the condition of the car, the keychain shows the user time, the temperature in the cabin, as well as alarm clock.

You can install the presented system on machines with diesel, gasoline or turbocharged engine type. The gearbox can be automatic or manual.

Safety regulations

Using the functions of the remote or automatic engine start, the control of the machine nodes, it is necessary to follow the safety measures to use the Starline A9 system. The instruction manual clearly indicates.

The car is important to park on a well-viewed area. In this case, it must be installed on the parking brake. The automatic transmission lever must be in PARK position, and the handmade gearbox is in neutral.

Keychain management

If the owners of the car use several keyfobs with the display, then all information about the status of car systems and alarm will be displayed on the device screen from which the command was served.

Purpose buttons

Setting the "Starline A9" keychain with a liquid crystal display is performed using the three buttons on the housing. Their combinations make it possible to manage system functions.

Button II with a short press sets the position of the cursor on the screen. If you hold it 3 seconds, the trunk will open.

Pictures on display

After that, the modes of silent protection are followed. In this case, confirmation does not work. The following picture corresponds to the protection function with the beep. It goes off at a distance of the shock sensor.

Button I.

After such a programming, with a short press of the button I, the previously selected mode will be turned on. To set a new feature for it, again perform the above operation.

Button II.

Installation of watch

Starting to work with the system, you need to know how to set up time on the "Starline A9" key chain. You need to hold the III button until two beeps appear. The clock on the display will flash.

Code recording

To log in to the programming mode, you must enable ignition. The Valet service button is held before the appearance of four beeps.

Engine starting

Many drivers are interested in how to make the car with a keychain. "Starline A9" when connecting alarm involves programming the type of gearbox. If it is manual, when installing a wire loop is cut (as indicated in the instruction). If an automatic box is worth a car, this element is saved.

Reset installations

The service button must be pressed another 1 time. After that, another siren signal will sound. The driver presses the i button on the main key chain. A short signal will sound. This means that the reset was produced. From the settings mode, the system will automatically come out in 5 seconds. flare out 5 times. The keychain will publish a melodic signal.

Instructions for Alarm Starline A9 includes all the main points for setting up and installing. Therefore, before exploiting the anti-theft complex, it is necessary to familiarize yourself with the service leadership.

[Hide]

Technical characteristics A9.

Description of the main features of the auto start center for the car:

the magnitude of the carrier frequency for the transmission of control signals is 433.92 MHz;
the maximum range in which the main automotive signaling remote control can transmit pulses equal to 600 meters;
in the mode of receiving messages from the microprocessor unit, this parameter is 1200 m;
the range of operation of an additional communicator in the mode of transmitting pulse data - 15 meters;
the sensitivity regulator refers to the class of piezoelectric;
the temperature range in which the security complex works efficiently and without failures is from -40 to +85 degrees;
the value of the power supply voltage of the anti-theft system is 9-18 volts, which allows you to set alarm with remote start on passenger cars and motorcycles;
the value of the current that consumes the system during the started protection mode is 25 mA;
at the outlet of the electrical circuit along which the siren is connected, this indicator is equal to two amperes;
the maximum permissible value of the current on the electrolyney section is 2x7.5 A;
at the output of the electrical caps to connect drive devices of the door locks, this indicator is 15 amperes;
maximum permissible current values \u200b\u200bon electrolycles block connection power aggregate, starter, ignition system - 40 A;
at the output of the electrical caps of additional control channels, this indicator is 300 mA;
to power the main communicator, an AAA class battery is required, designed for 1.5 volts;
in an additional pager, a CR2032 type battery is installed on 3 V.

It is necessary to consider that the range of action of the keychain and the antenna adapter will depend on several factors:

pajor Installation Places;
voltage values \u200b\u200bof the battery of the machine - its decline will lead to incorrect operation of the protection system;
the location of the electrolytes in the area from the antenna to the microprocessor module (interference may be interfered with electronic devices next to wires);
location of vehicle and car owner;
battery voltage in the communicator;
weather conditions;
radio frequency interference.

Equipment

Elements and parts included in the Startline A9 Signal Set with Engine Run Function:

The main communicator. It has a higher radius of action, its body is equipped with a liquid crystal screen. The device has the option of two-way communication.
Spare Communicator. Made in a plastic case without a screen.
Main microprocessor unit. TO this device All elements of the anti-theft complex are connected.
Transceiver with antenna adapter. This device is equipped with a temperature controller. Used to determine this parameter in the vehicle cabin.
Power unit temperature controller. The sensor is required to evaluate this parameter if you need to start the engine.
Two-level impact controller and sensitivity.
Diode indicator. It determines the state of the anti-theft complex.
Special device to turn on the service mode - the currency button.
Keys to activate and disconnect the anti-label function.
The end switch of the hood.
Mounting set of wires in order to connect all items.
Instructions Starline A9, which allows you to step by step and register the communicator to use the system.
Consumer memo.

Main features

Protection methods and sections protected by the system:

motor machine is provided by setting a lock relay that prevents unauthorized launch of the unit;
the hood locks, the luggage compartment and doors are protected from the opening; button switches are used;
lever arm manual brakes The machines are protected from shutdown, it is also provided by a terminal;
the presence of the impact controller allows you to protect the wheels, windows and body from the illegal movement of the vehicle, as well as shocks;
the ignition system is protected from unauthorized activation.

Provide effective protection at the same time several zones of the car will allow the correct A9 TEGA.

For the full protection of the vehicle in the alarm, the following features are implemented:

Dynamic code. The new algorithm for which it has been developed allows you to prevent interception of commands.
Ability to memorize the status when turned off rechargeable battery. When the battery is activated, the alarm will automatically go into the mode that was before turning off the power.
A limited number of disturbing cycles from controllers.
The ability to interrupt the siren signal without disabling the security mode.

Separately select the protective options that the system has:

Anti-primilation that allows you to block a motor in case of robbery attack on the machine. The function is activated by the communicator or a special button.
The possibility of remote activation of the panic regime when the siren is triggered when suspicious people approaching the car.
Alarm triggering when the sensitivity regulator is turned on.
Immobilizer that allows you to activate the engine blocking machine.
Turbo timer.
On all the events that occur with the signaling, the system is notifying a car owner by sending a message to the main communicator.
With unauthorized removal of the anti-theft installation, the power unit is blocked.

One of the main features of the alarm of this model is the ability to remotely start the engine engine. Moreover, the start can be carried out both by the command and timer. It is allowed to adjust this option in accordance with the air temperature or voltage value in the onboard network of the vehicle. To disable the function, special combinations are used, which are described in detail in the service manual.

About the problem In the work of the two-way function in his videos, the user Alexey Muravyev told.

Pros and cons

Advantages that allocate A9 alarm consumers:

The ratio of value and quality. All elements of the anti-theft complex are made in durable enclosures, which eliminates the likelihood of their physical damage.
The presence of a temperature controller in the cabin. This allows the consumer using a keychain equipped with a screen, learn about the temperature level in the car.
The presence of additional channels. Thanks to them, the user has the ability to install and configure the auxiliary equipment. For example, closers of electrical windows or hatch.
Detailed installation and configuration guide system. With its help, the consumer has the ability to independently install a security complex and adjust the main parameters.
Availability of display. Using the screen on the communicator allows you to simplify the procedure for setting up and operating a security complex.

Cons characteristic of this model:

The timer option incorrectly works. Because of this, consumers may arise difficulties with the launch of the machine motor through a certain time interval.
Low radius action of the communicator when operating in urban conditions. This drawback is particularly manifested in major cities. The range of the chapel work is influenced by interference from power plants and other equipment, which in the megalopolises more than enough. Despite the manufacturer's statements, the communication channel is not reliably protected from the effects of external factors.
Some consumers note such a disadvantage as the lack of dialog code. Old models of security complexes do not have this function, as a result of which they can be easily hacked with a grabber code. According to the manufacturer's application, it is almost impossible to do this, but on the fact the alarm is susceptible to hacking.
Sliding keys on a key chain in a few years of operation. Over time, the buttons begin to mess, resulting in inconvenience when arming and disable protection.

How to install?

After examining the instruction of Staline A9, the installation of the anti-theft complex can be independently. But for this it will be necessary to deal with the card that comes in the kit.

If the Starline A9 is installed and errors are allowed during connectivity, security system It will work incorrectly, it can be arbitrarily disconnected, which will reduce the safety of the car.

Connection scheme

General scheme for connecting alarm Starline A9.

Step-by-step instruction

Anti-theft Installation Guide:

Procedures are turned off terminals from acb. For this, the wrench must be loosen the clip at the battery output.
Installation of a microprocessor module in which the board is located, is made in a hidden place, it is best to place it under the control panel. This will ensure the minimum length of cables when connected. To prevent moisture from getting inside the microprocessor module, it is recommended to install it down by the connector. It is necessary to qualitatively fix the block on a flat surface to eliminate the negative impact of vibrations. You need to fix the device with the help of screws or bilateral scotch.
Antenna block is installed inside the cabin on the surface windshield. It must be placed so that the distance from the device to metal on the body amounted to at least 5 cm. This will prevent the negative impact of interference that affect the radius of the communicator.
Before installing antenna, the surface of the windshield must be cleaned and degreased. Since the temperature controller is located inside the device, the adapter is not recommended to be placed next to the stove or other heat sources. It is desirable that solar rays do not affect him. Otherwise, the testimony that gives the temperature sensor will differ from the actual one.
The external controller is installed on the power unit under the hood. Its fixation is carried out on the cylinder body for one of the existing M6 screws. It is important to provide high-quality contact of the temperature sensor with the COF Case.
Installation of the siren is made in the engine compartment. The place of its placement should be away from the sources of moisture and heat. The device is put on the mouth down, thanks to this, water will not be gathered. When installing, you need to make sure that from under the bottom there is no access to the siren, as well as the conductors for which it is connected.
The shock controller is installed in the cabin of the machine. It is recommended to place it in the center of the body so that it can effectively determine the impact on the car on any side. When installing, it is necessary to ensure unobstructed access to the controller adjustment elements.
The diode indicator is fixed in a prominent place on the control panel. The cable laying is carried out under the dashboard.
The cash key of the currency is mounted in a hidden place. The same principle must be adhered to the installation of the anti-label button. But the consumer must have direct access to these items if necessary.
Installation of push-button switches is performed on the doors of the luggage compartment and under the hood. They must be installed so that with closed locks to the devices there were no access. After installation, the diagnosis of the correctness of their functioning is performed. If errors will be made when installing the terminats, will result in false alarm response.
Under facing plastic cabin, in particular, under the thresholds, all wires are locked. Cables must go from the alarm elements to the microprocessor module and connect in accordance with the scheme.

Indicator designation on the pager screen

Description of the Icons on the display of the Communicator:

1 - a discharged battery icon in the device;
2 - the inclusion of the second additional channel;
3 - launched the automatic dvc mode in accordance with the temperature of the unit;
4 - Machine Motor is equipped;
5 - open door of the luggage compartment;
6 - not locked door locks;
7 - indicator of the function alert function of events by vibration;
8 - a symbol of the included service mode of the currency;
9 - an automatic reactivation icon of a protective function;
10 - This indicator reports on silent protection mode included;
11 - a security function with sound accompanies is launched;
12 - Open indicator motor compartment car;
13 - a symbol of triggering a sensitivity regulator, reports the activation of the first or second level of the impact controller;
14 - shut off hand brake car;
15 - indicator in the form of a locked lock reports about closing the door of the machine;
16 - if the same symbol is modified on the open, the door products are not locked;
17 - wait indicator, when activated it, the alarm reports that only the receiver of the communicator functions;
18 - Icon transmission of pulse data by a pager;
19 - Symbol for calling a car owner from the car;
20 - This indicator reports activation of the communicator power saving mode;
21 - inclusion of ignition;
22 - activation of alarm clock;
23 - Symbol of the morning day;
24 is also a daily indicator, only afternoon;
25 - the icon of the daily start of the DVS either its start in accordance with the testimony of the alarm clock;
26 - a symbol of time, temperature, as well as modes of the remote start of the power unit;
27 - Indication of the temperature scale;
28 - indicator of the timer.

Setting the keychain

Designation of elements on the case

To program the communicator, you need to tie it the first button. The value of this key is configured and can be changed if necessary. Reprogramble the button can the bus owner an unlimited number of times. To ensure more convenient use of the security system, it is recommended to configure the key to activate and disable the protective mode.

Programming Guide:

The 3 Communicator button clicks two or more times that the cursor on the device screen moves clockwise or against it. So that the direction of movement has changed, you need to make a two-second pause between clicks.
The key must be set to a position that matches the necessary command. For example, it may be the activation of the protective mode and its shutdown with sound.
The button at number 3 is pressed and maintained in this position for six seconds. You must wait until the key chain erupts two, and then three beeps.
To program the first key, it must be briefly clicking on the switching on the desired option.

Subsequently, when operating a security system, one click on this button will contribute to the execution of a specific command. In this example, it is activation and disabling the protective mode. When you press the key, the indicators will be turned on, which correspond to a specific option. If you want to reconfigure the button, the described procedure is repeated to change the purpose of the item.

Installation of watch

Adjusting temporary readings is as follows:

The third communicator key is clamped and maintained in this position for a few seconds. We must wait until the key chain erupts two short-term sound signals. The clock symbol on the pager screen will blink.
To increase the values, you need to click on the first key, reduce - on the second. For a faster increase or lowering the buttons are clamped.
When the clock is set, you need to set up minutes. For this, the third button of the communicator is clicked. The procedure for increasing the readings is carried out similarly - using the first or second key. To speed up this process, the buttons can be clamped.
To leave the temporary settings menu, the third keychain button is held while the device does not emit a beep. You can not take any action, and after a few seconds the Communicator will do it automatically.

The CRSSSOVER 159 channel spoke about the features of adjusting the time parameters in the Starline pager.

Installation of alarm clock

Programming process:

The setup procedure is performed by clamping a third keychain key until the device has emit two short-term sound signals.
The same button is clicked consistently, an icon in the form of a clock appears on the screen. This will lead to the blinking of the alarm symbol.
To increase the time values, the key 1 is used, and to reduce the second button. For accelerated adjustment of the parameters, you must clamp these items.
After setting the clock, you need to configure the minutes, for this, the third page of the pager is clicked.
Then the same button is pressed to go to the activation menu or disable the function. To enable the option, the first key clics, for shutdown - the second. The corresponding character (ON or OFF) will light up after the selected action.
To leave the setup mode of the parameters, the third button is clamping, while the keychain will not emit a beep. This can not be done, but you have to wait a few seconds so that the device came out from the menu automatically. When the alarm clock is on, an icon in the form of a clock is on the screen. When it is activated to shut down, you can press the third button.

How to set a timer?

Timer Programming Algorithm:

To go to the setup menu of this parameter, the key is also clamped at number 3 until two short-term sound pulses are turned out.
This button is sequentially clicked, the cursor on the communicator screen will go to the timer menu. This is an hourglass icon.
The parameter adjustment procedure is performed in the same way as in the case of alarm clock.
The maximum value that can be configured on the timer is 19 h 59 min.
When the function is activated on the Communicator screen, the current state, as well as a flashing indicator in the form of an hourglass, will be displayed. When the option works, there will be eight sound signals and the timer symbol will disappear. To interrupt pulses, you need to click on the third key.
To quickly activate the function, it is necessary to simultaneously clamp the buttons under the numbers 2 and 3. This will lead to the marging of the indicator in the form of an hourglass on the screen, the timer time will also be displayed. The third and second keys are used to adjust the time parameters. When quickly setting up the step is 10 and 30 minutes.
When the option is enabled, the current state is displayed on the device screen and the blinking icon in the form of an hourglass.

Channel " The best choice - BMS "told about the nuances of the settings of the Communicator Starline A9.

Modes

With a short-term stop, the car owner may need to include alarm on the engine installed.

The activation procedure is performed as follows:

While the power unit is running, you need to pull the lever parking brake.
Then the first button cliches and clamping until parking lights Vehicle does not blunt three times. The communicator must publish a melodic signal. A symbol of smoke from the muffler will appear on the pager screen, the time of operation of the power unit will appear. The diode light bulb will burn without a break. If the time parameter for the engine is not configured, the R99 indicator will appear on the display.
Then the key is removed from the ignition lock, it is necessary to leave the car's interior. The motor will remain in working condition.
The doors of the car, the luggage compartment and the hood are closed.
The first button on the communicator is clicked. In confirmation of the inclusion of this feature, one signal of sirens and overall lights are blocked 1 time. With such an inclusion of protection, the sensitivity controller does not work, as well as the zone of protection of the ignition system. If the door locks are connected to the anti-theft installation, they will also close.
In confirmation, the communicator will publish one short-term signal. On its screen, indicators in the form of a closed lock turned on with siren and smoke from the muffler. The current time will also be displayed. If the engine stops, the protection mode will remain on. It will activate the protection of the ignition zone and the impact controller.

About the setting of modes, as well as service options told the user Michael MNS.

The emergency activation mode of the protection system without a communicator will be useful in the event of a breakdown of the latter.

Enabling and setting is done like this:

The ignition is activated, it is not necessary to run the power unit.
The wallest key is pressed eight times.
The ignition system is turned off. The overall lights of the car are blinking once, the siren will publish a beep.
Over the next twenty seconds it is necessary to leave the vehicle salon and close all door locks with the key. Sirena will have a beep, one time should work the communicator.
After 20 seconds after that, the alarm protection mode is activated. Overall lights must blink again. The diode status indicator of the security system will flash by demonstrating the protection mode included.

If the manual brake lever has not been activated, then after connecting the function, four audio impulses will be distributed. The overall headlights of the car are burned as much time.

To disable this mode, you need to do the following:

Opened using the key driver's car door. The anti-theft installation will work, the siren will reproduce the alarms.
The key is installed in the lock, the ignition is activated. The power unit does not need to start this task.
For twenty seconds, it is necessary to click on the service key of the currency four times.
Ignition deactivation is performed. The siren should publish two sound signals, double the overall lights of the car twice. There will be deactivation of the protective regime.

User Alexander Shkurevsky told about the settings of the STARLINE signaling parameters using a keychain.

Setting up autorun.

Before activating this option, you must prepare a power unit of the machine if vehicle Equipped automatic transmission.

Engine preparation is performed as follows:

The car stops, it is not necessary to disable it.
The gear lever is set to a neutral position. Activation of the parking brake is performed to fix the car on the spot.
Ignition turns off, the key can be removed from the switch. The power unit should remain in working condition.
For thirty seconds you need to get out of the car. All door locks are locked, the protective mode is activated. For this, the first key of the communicator is clicked. The power unit of the car will stop immediately or continue to function before turning off the turbotimer mode.

There are two versions of the remote start of the power unit of the car by the team:

On the display of the communicator, you need to translate the cursor to the icon with the inscription "START". Under it is a symbol in the form of an asterisk. Then the second key of the communicator is clicked.
You can also click on the first button of the control panel and hold it for three seconds. This will lead to a commissioning of the command.

User Vavan 176 demonstrated a remote power to turn on the machine with a keychain.

The start of the power unit can be performed daily at a certain time. This option is especially useful in the morning, since it allows you to sit down the driver in an already warm car. To activate the function, you need to translate the cursor on the communicator display on the "START" icon. Then the second pager keys clicked.

If the function is configured, the siren will play a signal, the same communicator will make the same, the overall lights of the machine will be blocked. The pager screen appears in the form of a check mark. The status diode light bulb will blink two outbreaks.

You can adjust the basic parameters according to the temperature mode, for this it is used by the sensor installed on the engine.

DVS starts when:

-5 degrees;
-10 degrees;
-15 degrees;
-20 degrees.

The setting is subject to the DVS warming duration, as well as the startup function. The largest number of automatic starts of the motor in accordance with the temperature for one day is 12, the interval between attempts will be 1 hour.

To activate the function, you must translate the cursor on the symbol with the "START" symbol and the key icon. Then the second pager keys clicked. Sirena will emit one beep, once blinking the overall lights of the machine. Must work the communicator itself, an indicator with a key icon will appear on its screen, as well as the temperature value at which the start will occur. The diode status light bulb will blink with series consisting of three flashes.

The user of NYUR GUN showed how the user can face when setting the automatic startup option.

How to bind a new key chain to Staline A9?

Alarm allows you to drive up to four communicators. Each new keychain makes information about yourself in a microprocessor module. But at the same time, the data on the rest of the communicators are removed from it. Therefore, if you need to reflash one pager, you will have to re-introduce information about other devices.

The procedure is performed when the protection mode is disabled:

Ignition activation is performed.
The honeystone is clicked and maintained until the siren leaves four beeps.
To make information about the communicator in memory, you must simultaneously click on the first and second key. If a pager is programmed without a display, a spare, then the buttons under the numbers 3 and 4. On the successful email information to the microprocessor module, will report one siren sound signal.
The previous item is repeated for all communicators. The time between the recording of each subsequent device should be not more than five seconds, otherwise the security system will leave the binding mode.
Then the ignition is turned off. Overall lights of the car must blink five times.