How to secure your car from the hijacking? Today, this question worries every motorist, and therefore the range of security systems offered to help him is constantly expanding. What to make a bet? On attractive characteristics or budget value? Alarm Starline A9 eliminates the owner of the machine from making a decision (it successfully combines both the first and second).
Protection 100%
The automotive system for the protection of this model is rightfully considered one of the best. And there is reason: a high indicator of the degree of protection. Such enviable safety is due to two moments:
- Complex original encryption principle. It is he who is based on a dynamic code, reliably protected from interception. Hacking an individual cipher is practically unrealistic (but the manufacturer decided to progress and strengthen the effect using a non-standard solution).
- An extraordinary innovative approach. This model of auto alarms is successfully applied and the principle of zoning. Each individual plot is guarded (internal combustion engine, parking brake, hood, doors, trunk, windows, ignition lock). And for it corresponds to a specific device (switch, sensor, relay). All information about trying to hack or cause harm is displayed on the alarm key chain. Alarm signals are included when exposed to any of the above zones.
The impeccable work of protective functions is also due to the fact that the state of all elements of the system is constantly under control. The failure of one of them is diagnosed by the device itself in a matter of seconds (the owner of the car learns about an existing problem immediately after their detection). This option (self-diagnostics) completely eliminates any risks (provided that the motorist will take the necessary measures to eliminate them in a timely manner).
Comfort class "Lux"
Another advantage of the STARLINE A9 alarm is to combine its ability to combine pleasant. It is replete with options that greatly facilitate the life of the owner of the machine, and at times increasing the degree of its comfort during operation vehicle. To such decent attention, the functions of this model of the security system can be attributed:
- Autostart. Runs the engine at a certain time (the setting can be produced in three directions: depending on the temperature mode, the waiting timer, the alarm time)
- Anti-Frame mode. It triggers when, after opening a driver's door, confirmation of the displayed cipher of the owner, through a given number of meters the system blocks the engine operation.
- Immobilizer mode. Relevant for those who forget to step by step press the buttons on the keychain, is activated after 30 second lack of actions from the driver (blocks the motor after half a minute after the ignition is turned off).
- GSM Module Starline. Allows you to control the alarm from your mobile device, as well as receive messages about the state of the system.
- Indication. The alarm keychain can replace the clock, and alarm clock, and a timer, he will also inform the engine time (such information may also be needed by motorist).
This is not all the possibilities of this model, the table shows only the most sought-after from them.
Cares and energy efficiency. Situations when the keychain does not respond to the commands of his host most often associated with the wear of its power elements, in the Star Line A9 panel of the batteries serve at least 2 months (more often to six months).
Installation without problems
Automotive alarms of this brand and the model are good and the fact that they can be installed independently. This process can be characterized as complicated and simple at the same time. The difficulty lies in the fact that it involves a large amount of work, which must be implemented in accordance with the strict algorithm of actions regarding:
- location and fixation of system elements (Recommendations: The central unit is desirable to fasten under the dashboard, the transceiver module on the windshield, the shock sensor in any place of the cabin, the LED indicator near the instruments, the temperature remote sensor on the motor hull, siren in open space shore down away from highly heated parts of the engine);
- connection schemes(Wire gaskets, installation of electrical wiring connections, connecting the circuit responsible for the operation of sound and light equipment, systems with auto start, doors activator, locking system, engine lock, engine operation control over one of the options: tachometer, onboard network voltage, generator).
Easy to install Starline A9 is that the instruction manual is included in each implemented product of this type, gives a clearly detailed view of everything that concerns its installation. It can also find a description of the reasons that can lead to incorrect. unstable work Installed security system (errors made during the installation process).
Setup without much effort
All of the owners of the cars, which establish the alarm of this model, are interested in two important questions: how to tie a key chain to the system and how to configure the desired parameters for each of the modes offered by the manufacturer. To help car enthusiast detailed instructionsconcerning its interests:
- Binding keychain. We act step by step:
- we bring the car;
- press the "Valet" button (Before the appearance of 4 sound signals, we hold it);
- at the same time, press the buttons 1 and 2, release after 1 audio signal (to program the keychain with the LCD display - the main PU);
- simultaneously press the button 3 and 4 (relevant to record additional keychains).
- Programming parameters. We follow the next action algorithm:
- press 6 times the service button when the ignition is turned on (We will make the response of the system: 6 flashes of LEDs + 6 audible signals);
- press the "Valet" button several times. (before going to a specific function);
- select the desired value, confirm the action either short or long pressing the buttons 1 and 2 (half a second or 30 seconds);
- returning to "Start"by pressing the service button;
- repeat actions for all functionsin need of special settings other than factory parameters;
- we leave from programming mode (turn off and turn on the ignition or wait for an automatic shutdown, accompanied by 5 outbreaks overall lights).
Convenient management
In order to competently manage the automotive security complex called Starline A9, you do not need to have a special education. The key chain with the LCD display is a kind of book with pictures, you just need to choose the right picture. Another thing is an optional control panel (push-button panel may puzzle). However, the instruction manual included in the alarm summary For use, the task of the motorist will be simplified. These carriers crucial information Will help you find answers to all questions. There are all: connection schemes, mounting cards, methods of binding and controlling control panel (keychain), programming methods of options and parameters, and even a list possible faults and their removal techniques.
The virtues of Starline A9 is enough. Why not take advantage of them!
Greetings, dear readers of the site!
I want to tell you a story about replacing the block for the Starline car alarm.
If briefly, it works, it works, I recommend!
From recently, I started to join me on the main key chain of the alarm, it was sold and triggered one time. It was decided to disassemble and see what happened there.
The autopsy showed that due to the design curve of the buttons and the frequent use of the same button, the legs could not withstand the tension and decided to break away from the board.
The button first soldered at home, was enough for a week. Next was soldered on a soldering station with a special, more solid tin, also had a short time, fell off three weeks later.
so it turned out in the end
This button is just tied to the power on / off, so very necessary. Of course, there is a second, programmable button, with which you can also put on guard, but it is inconvenient.
Therefore, it was decided to purchase the second key chain.
I have a fairly old alarm and the original keyfobs are practically not found, and what can be found is not a fact that it turns out to be the original. + Translate price tag.
The fluid search has shown that there are key rings on Ali, but under different veiled names, it very complicated the search. For example, this seller called her Tamarack, the other was Twace, everything is looking for on the word Starline - with a horse price tag.
Also upset the fact that the keyfobs specifically for StarLine A8 are not only for A9. The officially STARLINE state reports that the key rings are not compatible, but at the same time on the profile forum the people wrote that partially compatible and there may be problems with the key fob in the signaling of the signaling, as well as some functions may not work.
A deeper google led to the conclusion that all the same key chains are compatible and basic functions work.
For A9, the choice is much more diverse (against zero for A8). I came across this lot, the price tag was one of the lowest. Of course, it was embarrassed by a small rating of the seller and a modest assortment in the store, but I took the final decision after reading one of the comments that one buyer was successfully stitched by A8. Mostly all the other reviews are good, it was decided to buy.
I ordered, paid, everything is OK. I sent the seller about the 3rd or 4th day, I don't remember exactly already.
Track with tracking. Delivery on current standards is not fast - exactly a month.
Packaging on a troeuchka, a yellow package, the key chain itself in the puppete package, unreliable however. On the way, all the puppies were pleased with mail employees, while they were thrown by my parcel. Therefore, it was worth packing better, they could have broken the screen.
The seller even put this postcard, signed himself. Again, 5 stars asks.
At the sight of a large similarity with the original, although I also can't know if I have the original, because I received a signal from the car and I don't know anything about her biography.
Differences can be reduced that after all, my key chain from A8, and this one from A9.
The case is absolutely the same, quite a bit deeper than the hole under the button and the buttons themselves are made from another material, slightly larger out of the housing.
Pictograms on the screen are a bit brighter from the new, perhaps on the old one they focused on time.
Illumination of the same color. The resulting keyfob seems a little worse the screen in quality, if you look at the top, then the badges are flexible, the old one was also, but not so much expressed.
In general, more visual differences did not find.
External comparison
Even there is a holographic sticker StarLine :) 
I stitched the key chain with a bang, works as a native. Programmatically distinguished by the A9 key chain from A8 consists only that the cursor of the programmable button 2 over time hesitates to the default position, there was no such thing on the old old one.
I stitched on this instruction:
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
1. Turn the ignition.
2. Press and hold the VALET service button until 4 siren signals appear.
3. To record the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
4. Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
5. Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.
When I stitched new keychain, missed very much important moment, the button then on the old one is broken and it will not work it. Thus, if something went wrong, I would stay without a signal for a while, but everything went like on the oil, the new key chain was lying without any problems. Now it remains to fall the old old and flash it, it will be a spare.
Checked the main functions, accurately work:
- Removal / arming, with sound and without.
- alarm on the shock sensor 1 and 2 levels with feedback
- autorun and engine stop.
- Request information about the status of the car (temperature, whether the engine is launched, do the doors, the position of the handbrake, ignition)
- Opening the trunk on the second channel.
In the rest of the functions I do not need, so I did not check.
To whom it is interesting, for comparison, photos of the insides, on top of the old keychain, under it overlooked sabzh.
It can be seen in the naked eye that in the version A8 screen on the loop, in A9 Wpayan on the legs 
Separate fees did not, reluctant to gut a new key chain, but visually there are differences in circuitry 
And again these buttons that, I hope this time stretches for a long time. (Photo after the 3rd propios of the old key fob) 
By the time the review is published, the old keychain was released, the button started again. Both key products have been successfully recorded in the signal of the signal. Unfortunately, they do not work in a pair, that is, when the alarm is triggered, the key chain, from which they put on guard, will be silent. The status of protection does not change dynamically on both keyboards, only on the one from which you install / remove the security.
In general, they work according to the principle - who is the last, that and dad.
The goods are purchased for money and on its own initiative. If someone decides to buy a key chain from this seller, write in the comments, I will try to negotiate a discount for Muskovchan.
For Sim I speak, thanks for watching!
I plan to buy +16. Add to favourites I liked the review +24 +52Alarm "Starline A9" is very popular with drivers different cars. The system package includes a detailed instruction. It allows you to connect and configure alarm. The manual also spelled out the principles of system operation. After studying user feedback and the provisions of the instruction, you can highlight the basic principles of working with Starline A9. Programming a keychain will be a simple task. Tips of experienced motorists will allow you to configure quickly. It will give the opportunity to enjoy all options. The alarm can be configured to work in or without autorun mode. The blocking function is also adjusted.
General
"Starline A9", the instruction manual of which requires studying before starting to install the system and programming a key fob, is alarm with remote engine start. It has a double-sided radio channel. Its range on the area without obstacles is 600 m. In the pager mode, this indicator increases by 2 times.
Radio signal coding is dynamic. The selection of control commands is carried out on the cursor principle. Each command is controlled by its button. It is displayed on the key fob. The system provides sound and vibrating signals alert.
In addition to the main data on the condition of the car, the keychain shows the user time, the temperature in the cabin, as well as alarm clock.
You can install the presented system on machines with diesel, gasoline or turbocharged engine type. The gearbox can be automatic or manual.
Safety regulations
Using the functions of the remote or automatic engine start, the control of the machine nodes, it is necessary to follow the safety measures to use the Starline A9 system. The instruction manual clearly indicates.
The car is important to park on a well-viewed area. In this case, it must be installed on the parking brake. Lever arm automatic transmission Must be in the PARK position, and the handmade gearbox is in neutral.
You can not run the engine in the absence of a driver in the cabin, if someone is located in front of or car. The keychain is unacceptable to give to children or persons who can not manage this device. The machine must be in good condition, in its system there must be a sufficient amount of all supplies and fuel.
Keychain management
The laid signaling functions are performed automatically or by key fob signals. Some of them can be changed. The procedure is spelled out in the instructions for the Starline A9 system. Programming the keychain is simply carried out. For this, the device has three buttons. Information is displayed on a liquid crystal display.
Driving a car can be performed by one or more keyfobs. If the main device is lost, you can use the spare console. This is a key chain with buttons that has no information for providing information to the user. With it, you can manage almost all system functions.
If the owners of the car use several keyfobs with the display, then all information about the status of car systems and alarm will be displayed on the device screen from which the command was served.
Purpose buttons
Setting the "Starline A9" keychain with a liquid crystal display is performed using the three buttons on the housing. Their combinations make it possible to manage system functions.
Button I may include the programming command if it is quickly pressing once. Holding her 3 seconds, the driver remotely starts or stops the engine. The user can enable security mode. To do this, with the engine running, this button also holds 3 seconds.
Button II with a short press sets the position of the cursor on the screen. If you hold it 3 seconds, the trunk will open.
Button III also allows you to manage the cursor position when you click. It interrupts key fob alert signals. To do this, it is kept pressed 0.5 seconds. To enable or disable clock setting mode, alarm clock, energy saving, this button hold 3 seconds. If you hold it squeezed for 6 seconds, you can enter the i button programming mode.
Pictures on display
All information about the state of the car and the signaling itself can be viewed on the Starline A9 system display. Icons on the key chain will help to navigate in setup and control modes. The instructions are clearly spelled out which picture corresponds to a function or another.
The indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general view of the device functions. To fully understand the appointment of each of them, you need to carefully examine the instructions.
The first picture that is located on the left corresponds to the anti-label mode. If it is on the display, this command is turned on. Next, the function of the additional channel 3. Moved to the right side, you can see the motor autorun mode in terms of temperature. Next is the function of daily autorun or turn on the an alarm engine. This picture follows the remote switching on or off of the motor.
After that, the modes of silent protection are followed. In this case, confirmation sound signals are not triggered. The following picture corresponds to the protection function with the beep. It goes off at a distance of the shock sensor.
A little more about the picture of the Valet service mode is. It should be displayed a picture of the state of car systems and salon temperature indicators. Next, there is an additional channel 2. Ends the chain of the pictures remote opening of the trunk.
Button I.
The i button on the main keychain is programmed by the user. This can be made an unlimited number of times. Most often it is used to shut down or switch on the security mode in the Starline A9 system. Programming a new keychain is simply performed.
Use the III button to move the cursor over the screen. When the desired mode is selected, for example, the inclusion of the protection function or any other, the movement is stopped. The III button is held for 6 seconds. First, two beeps will sound. Then more 3. Then then button are pressed to activate the selected function.
After such a programming, with a short press of the button I, the previously selected mode will be turned on. To set a new feature for it, again perform the above operation.
Button II.
You can assign a function for a button II. You need to press quickly button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue to move, it will move counterclockwise.
The pictures listed above will be selected one after another. When the cursor comes to the desired program, the movement of the III button is stopped. To execute the selected program, the user presses the ii button.
After 10 seconds after pressing any button, the cursor will return to the original CHECK state. This command controls the condition of the machine and temperature in its cabin. It does not change the status of alarm. Knowing this, the user will not have a question how to see the temperature on the Starline A9 key chain. When operating, it is this team that is the most sought-after.
Installation of watch
Starting to work with the system, you need to know how to set up time on the "Starline A9" key chain. You need to hold the III button until two beeps appear. The clock on the display will flash.
To enlarge the digital value of the clock, minutes, you need to press the i button, and to reduce the II button. The transition from the clock to minutes is carried out by a short press of the III button.
Upon completion of the settings, you need to exit the clock setting mode. To do this, hold the III clad button before the appearance of one beep. According to the manufacturer's instructions, you can set the alarm or timer readings.
Code recording
The driver can independently enter into memory system "Starline A9". Programming the keychain is performed in the protection mode. You can bind up to 4 remotes. This must be done if the alarm for some reason does not see the key fob signal or the machine with the already installed system.
To log in to the programming mode, you must enable ignition. The Valet service button is held before the appearance of four beeps.
First set up the main key chain. It clauses the I and II buttons. For additional remote controls, buttons III and IV are pressed without display. After successfully recording the first keyfob, one siren signal will sound.
For all keyfobs, the same procedure is performed. The interval between the record should not be more than 5 seconds. Otherwise, the programming mode will be completed automatically. Next you need to turn off the ignition. The success of the operation will confirm 5 outbreaks of the machine lights.
Engine starting
Many drivers are interested in how to make the car with a keychain. "Starline A9" when connecting alarm involves programming the type of gearbox. If it is manual, when installing a wire loop is cut (as indicated in the instructions). If on the car it costs automatic boxThis element is saved.
The engine type is also set. There are two features of the remote launch of the motor. In the first case, you need to put the cursor on the corresponding icon on the display screen. Then you need to press the II button. Or simply clamping button i for 3 seconds.
With the first attempt to start 3 beeps of sirens, 3 outbreaks of overall lights. The keychain will publish a melodic signal. The icon on the display will burn constantly. You can set the engine warming time.
Reset installations
Sometimes the driver may need information how to reset the Starline A9 keyword settings. Actions are manufactured in a specific sequence. Ignition first turns on. Next, the Valet service button is pressed 10 times. After that, the user turns off the ignition. The entrance to the discharge mode is made if 10 beeps of sirens sound after these manipulations.
The service button must be pressed another 1 time. After that, another siren signal will sound. The driver presses the i button on the main key chain. A short signal will sound. This means that the reset was produced. From the settings mode, the system will automatically come out in 5 seconds. Overall lights flashed 5 times. The keychain will publish a melodic signal.
Having considered the features of the automotive alarm "Starline A9", programming the keyboard you do easily and simply. Before working with equipment, you must read the manufacturer's instructions. This will allow the enjoyed functions fully. If necessary, you can return the system to the factory settings. Control keychain will allow you to use security system The car is comfortable and fully.
The alarm provides the opportunity remote disconnection / Turns on the shock sensor in the levels an unlimited number of times during a single security cycle.
If you need to disable only the preliminary level of the shock sensor, set the cursor to the icon, press the 2 button once. An additionally icon will be displayed on the display display, the 2 siren signals and a melodic signal keychain will be displayed. The first level of the sensor will be disconnected. If you need to turn off both levels of the shock sensor, set the cursor to the icon and click 2 keyword the second time. The icon appears on the keyboard display, and 3 beeps will be performed. Both levels of the shock sensor will be disabled. If you need to re-enable the shock sensor, set the cursor to the icon and click 2 keyword the third time. The icon will disappear from the display of the keychain, and 1 beep sounds. Both levels of the shock sensor will be turned on again.
Manage the central lock with a keychain when the ignition is turned on
When the ignition is turned on, the sequential pressing of the 1 keychain will lead to alternate closure and opening door locks.
On the display keychain will be displayed icons:
When closing locks;
When opening locks.
The ignition enabled is indicated by the icon.
Automatic control of the central lock from the ignition key (programmable function)
At your request, a function can be introduced automatic control Door locks when the ignition is turned on and off. If this function is turned on, then when the ignition is turned off, the door locks will be automatically open.
You can program 3 castle control options when the ignition is turned on:
- castles are not locked;
- locked after 10 seconds after the ignition is turned on;
- locked 30 seconds after switching on the ignition.
Attention! If one of the doors is open at the moment of inclusion of ignition or after switching on the ignition within 10 or 30 seconds, the locking of the door locks will not occur.
Open Door Alarm (Programmable Function)
At your request, the open door alert function can be programmed when the security mode is turned off. When opening any of the doors, the dimensions will flash for 10 seconds or until the door closing.
Control service life switches
Car search mode
To search for your car in the parking lot in dark time Tap simultaneously buttons 1 and 2 keychain.
If before this, the protection mode turned on or turned off with sound signals
confirmation, follow 6 siren signals and 6 outbreaks of dimensions. If the mode
The protection turned on or turned off silently, then by the team from the STARLINE alarm
TWAGE A9 will follow only 6 outbreaks of dimensions.
In both cases, a melodic signal keychain will sound.
Monitoring car condition
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow.
On the display, the temperature is displayed in the car's cabin (for example,) and the status of the alarm protection mode, the melodic signal will sound.
Note. Temperature display scale (Celsius or Fahrenheit) is programmed.
The temperature indicated by the keychain may differ from the real value depending on the installation location of the transceiver module in the car (for example, when the module is located on the Sun, the indicator temperature value will be more real.
Call from car
To serve a call signal from the car to the alarm keychain, press the button located on the case of the transceiver module. 6 outbreaks of dimensions follow (2 series of 3 flash). The icon appears on the keyboard display, and 20-second call sound signals are turned on. To interrupt the signals and display on the display, press the 3 keychain button.
Turbotimer Mode (Programmable Function)
For turbocharged machines, a special turbotimer mode is provided, which allows you to keep the engine operation after turning off the ignition with the key for some time required to complete the turbine stop. Thanks to this algorithm, the resource of the turbine sliding bearings is preserved.
The duration of the turbotimer is programmed 1, 3 or 6 minutes. If during operation of the turbo mode, accompanied by the lighting of the LED indicator, the protection mode will be turned on with locking locking locks, then the system will turn off the ignition inputs and the shock sensor during the turbotimer. Engine locking will not happen. The engine will be stopped automatically, and the ignition zones and the impact sensor will be protected only after turning off the turbotimer mode. The LED will start slowly flashed.
Attention.
Control of the health of limit translation switches STARLINE TWAGE
A9.
In the alarm, it is possible to control the health of the end switches of the doors, the hood and trunk when the security mode is turned off. Opening the doors, hood and trunk when the ignition is turned on, must be accompanied by flashes of the LED indicator. If the LED does not light up when they open, it means that the corresponding terminal switch is faulty.
Monitoring the condition of the car and temperature in the cabin
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow. On the display, the temperature is displayed in the car's cabin and the status of the alarm protection mode, the melodic signal will sound.
Note. The temperature displayed on the display of the keychain may differ from the real temperature in the cabin as it depends on the installation site in the car of the transceiver module (for example, when the module is in the sun, the indicator temperature value will be more real).
Service mode Valet.
For
temporary disconnection of anti-theft and security functions of the STAR auto alarm
Line A9, for example, when transferring a car to a service station
for prophylactic or repair work It is recommended to include
Walt service mode.
Before switching on the VALET mode, make sure that the previously programmed modes of the turbotimer and the immobilizer are turned off. Otherwise, log in to the programming mode and setting the alarm and switch the specified modes to the state - off.
To enable the service mode, set the cursor to the icon and click 2 keychain. The confirmation will follow 4 of the siren signals, 4 outbreaks of dimensions and sound a melodic signaling signal. A flashing icon appears on the display, when Valet is enabled, only the remote control function of the locking and unlocking door locks and control of the additional channel No. 1 continues to operate.
To turn off the service mode, set the cursor to the icon, press the 2 keychain button. keychain The confirmation will follow 3 Siren Signals, 3 outbreaks of dimensions and a melodic keychain signal. Icon goes out. If necessary, program the disconnected modes of the turbotimer and the immobilizer again.
Control of additional channel number 1 (remote spilling trunk)
Channel number 1 (yellow-black wire) It can be activated independently of the system of the system and used for remote spilling of the trunk. If the channel is activated when the protection mode is enabled, the trunk zones and the shock sensor are temporarily disconnected.
There are two options for the inclusion of an additional channel number 1:
Option 1 - Press and hold the 2 keychain button for 3 seconds.
Option 2 - Use the 3 keychain button. Set the cursor to the icon and click the 2 keychain button.
The confirmation will follow 3 outbreaks of dimensions and 3 beeps of the keychain.
When the security mode is turned off, the flashing image will appear on the display. open trunk.
With the mode of protection on the display, the keychain will appear flashing images of an open trunk and a disabled shock sensor
At the output of the channel there will be a negative impetus with a duration of 1 second - the trunk will open. If, when you activate the channel, the trunk will not open, then the indications of the open trunk and the disabled shock sensor on the display the keychain will not follow.
If at the time of the trunk closing the alarm will be in the mode of protection, then the zones of the trunk and the impact sensor will be taken under protection again after 5 seconds. The confirmation will sound 1 Siren Signal and 1 Sound Sound. Flashing outdoor trunk icons and shock sensor will disappear.
Advanced Channel Management 2 (Programmable Function)
An additional channel number 2 (yellow-red wire) can be activated regardless of the status of the protection mode by 0.8, 10, 30 seconds or before switching off by the keychain. The duration of the output signal is programmed when the system is set (Function 4). Channel can be used for remote control additional equipment car.
To turn on (off) the channel, set the cursor to the icon and click 2 keychain. The confirmation will follow 1 Siren Syrene, 1 outbreak of the dimensions and 1 sound keychain. On the display keychain displaying icon,
The icon disappears when the keychain is turned off.
Control of an additional channel number 3 (programmable function)
Additional
Channel number 3 (yellow-blue wire) can be activated regardless of the state
Starline A9 car alarm protection modes. When working in the mode of protection of the channel
Can be programmed for two options:
Option 1 - Channel activation without shutting down the security mode. The duration of the channel for this option is programmed: 0.8, 10, 30 seconds or shutdown by keychain.
Option 2 - Activation of the channel with simultaneous shutdown of the protection mode and unlock all door locks. The duration of the channel for this option is fixed - 0.8 seconds.
To turn on (off) the channel, set the cursor to the icon and click 2 keychain.
When the channel is activated by option 1, the confirmation will follow 3 of the siren signal, 3 outbreaks of dimensions and 3 beeps of the keychain. When operating the channel for option 2, only 2 sirens and 2 flash outbreaks will follow.
An example of using an additional channel number 3 to implement the function of two-step unpiration of door locks when the security mode is turned off
Before using the channel number 3, to implement a two-step unlocking door locks with simultaneous shutdown of security mode, it is necessary:
- Connect the driver's door activator and the remaining doors activators in accordance with the scheme below
- Enter the programming mode of functions and auto alarm installations and program a function 10 (an algorithm of operation of an additional channel No. 3) according to option 2.
To turn off the security mode with unscrupuling only the driver's door, press the button 1 keychain. When the security mode is turned off, the keyboard display shows the icon and follow the audio and light confirmation signals.
To unlock the rest of the doors, set the cursor to the icon and press the 2 keychain button, follow 2 siren signals and 2 flash outbreaks.
Control of an additional channel number 4 (automatic raising of glass or the inclusion of "polite" interior backlight)
Additional channel number 4 (blue wire) can be programmed for two options:
Option 1 - The channel is automatically activated when the protection mode is turned off and simultaneously with the appearance of alarms when the security mode is enabled. The duration of the channel 20 or 30 seconds is programmed when the system is installed. This algorithm can be used, for example, to include a "polite" interior backlight.
Option 2 - The channel is automatically activated only when the security mode is turned on. The duration of the channel 20 or 30 seconds is programmed when the system is installed. At the time of channel activation, the system does not respond to the shock sensor to avoid false positives. This algorithm can be used to automatically raise the glasses when the protection mode is turned on.
LED signaling status indication
In various signaling modes, the LED indicator flashes in different ways. If you do not have a keychain with a liquid crystal display, indicating the alarm and car status, then you can define the current signaling mode of the alarm by the type of flashing LED indicator. Types of flashing LED indicator in accordance with the signaling modes are shown in the table.
| Star Line Twage A9 Alarm Mode | Type of flashing LED indicator |
|---|---|
| The engine runs remotely | Lit constantly burning |
| Turbotimer mode included | Lit constantly burning |
| Immobilizer mode is turned on | Lit constantly burning |
| Protection mode is off | Does not burn |
| Protection mode is turned on | Slow flashes |
| Open doors, hood or trunk (with ignition on) | Quickly flashes |
| Included Mode of Daily Engine Auto Tackle or Start Budilin | Series of 2 outbreaks |
| Increased temperature autorun mode | Series of 3 outbreaks |
| Included autorun modes daily or starting the alarm clinic and temperature | 4 series of outbreaks |
| The Valet service mode is enabled. | 5 series outbreaks |
Engine starting
To implement the function of remote and automatic engine launch, at the steps of the alarm, must be programmed:
Type of car shift box (PPC) - automatic or manual. With manual gearbox, it is necessary to cut a wire loop in the central block, with an automatic gearbox - the loop must be saved.
Motor type of car - gasoline or diesel (programmable function No. 8). When the engine type is selected, the presence or lack of a starter is delayed after turning on the ignition at the first start attempt. For diesel engines Such a delay is necessary to warm up candles before starter starter. The value of the delay can be programmed by 4, 6 or 10 seconds (programmable function No. 8).
Remote engine start can not be implemented in the following cases:
- Included ignition;
- The hood is opened;
- Parking brake is turned off;
- On cars with manual gearbox did not prepare for the engine start.
Preparation for starting the engine on cars with manual gearbox (PPC)
Preparations for the start of the engine on cars with manual gearbox lies in the activation of "software neutral", which should protect the car from the engine start when the transfer is enabled.
The inclusion of "software neutral" depends on the programmed engine support mode. If AUTO mode is programmed, the inclusion is made as follows:
- Stop the car without turning off the ignition.
- Install the gear knob to the neutral position and place the car on the parking brake.
- Turn off the ignition and remove the key from the ignition lock. Engine is running.
- Within 30 seconds, leave the car, close all the doors, turn on the security mode by pressing the 1 key button. The engine will be stopped immediately or will continue to work until the turbotimer mode is turned off.
If the security mode is not turned on, the engine will continue to work for 30 seconds or turn off the turbotimer mode.
After the successful procedure described above, the car will be prepared for the start of the engine.
Attention! If after turning off the ignition according to claim 3, there is a sharp change idling The engine or motor stalls, it is recommended to program the SAFE engine support mode. In this case, to enable the "program neutral" mode, the actions of claim 3 must be performed as follows:
When the engine is running, press and hold the 1 channel button until 3 outbreaks of the dimensions and a melodic keychain appears. The display shows the icon and the engine operating time will display. If the turbotimemer is not programmed, the R 00 symbol appears. If the turbo-timer is programmed, the icon with the corresponding turbotimer R 01, R 03 or R 06 will appear. Now you can turn off the ignition and remove the ignition key from the lock. The engine will continue to work.
Remote Engine Start with Starline A9 alarm
There are two versions of the remote engine start regardless of the status of the security mode.
Option 1 - Install the cursor to the icon and press the 2 keyword button;
Option 2 - Press 1 keychain button for 3 seconds.
The first attempt to start the engine is accompanied by 3 siren signals, 3 outbreaks of dimensions and a melodic signal keychain. In the case of successful engine launch, additional 3 flash outbreaks will appear and the keychain can sound. The LED indicator will constantly light up.
On the display, the engine startup process is displayed as follows:
For one engine start cycle, the system can take 4 start-up attempts. If after 4 attempts the engine will not start, then the display shows the inscription, and the keychain will give 4 beeps, indicating the end of the start attempt. Four sirens and 4 outbreaks are followed by 4 signals.
If the engine running will stroke until the warming up time is completed, a new engine start cycle will be taken.
Note. The maximum time of the first attempt to scroll through the starter can be programmed 0.8; 1.2; 1.8; 3.0 seconds when installing alarm. The time of each subsequent attempt at the starter scroll automatically increases by 0.2 seconds.
If the engine is launched before the start of the maximum starter scroll time, then subject to the operation of the engine on the signal and generator signals, the starter will be turned off early. When controlling the operation of the engine voltage, the starter scroll time is determined by the programmed value.
Daily automatic engine start
The system has the ability to automatically start and warm up the engine at the same time (for example, every morning).
To enable the function of daily automatic start and warming up the engine, set the cursor to the icon and click the 2 button
1 Siren signal and 1 outbreak of dimensions follow. The keychain will give a melodious beep. The keyboard display shows the icon indicating the included daily autorun mode. The LED will flash a series of 2 outbreaks.
Simultaneously with the first inclusion of the function will occur automatic start Engine and its warming during the programmed time. All subsequent automatic engine launches will be made every 24 hours.
To turn off the daily autorun function, re-set the cursor to the icon and click 2 keychain. The keychain will give a melodious beep, the icon will disappear.
Attention! The unsuccessful start of the engine for any reason cancels the further programmed daily engine launches.
Automatic engine start time
Alarm has the ability to automatically start and warm up the engine with a decrease in the ambient temperature. Temperature control is carried out along the temperature sensor installed on the engine housing. Thus, the automatic start of the engine occurs when the engine temperature is reduced to -5 ° C, -10 ° C, -15 ° C or -20 ° C. Startup function, temperature value and engine warming duration are programmed. The maximum number of motor autoruns at a temperature for one day is - 12. The interval between repeated autoruns is 1 hour. The time to the subsequent launch is counting from the moment of starting the engine and does not depend on the warming time.
To enable the automatic engine start function, set the cursor to the icon and click 2 keychain. 1 siren signal will follow, 1 outbreak of dimensions, and a melodic signal keychain will sound. On the display, the icon appears the indicating power on the temperature in temperature, and the temperature value in which the engine will be launched, for example, the LED indicator will flash a series of 3 flashes. To turn off the temperature of the autorun temperature, set the cursor to the icon and click 2 keychain. Follow 2 sirens and 2 outbreaks of dimensions. The keychain will give a melodic signal, the icon will disappear.
Attention! The unsuccessful start of the engine for any reason cancels further programmed automatic launches by temperature.
Automatic Starting Engine Budil
The alarm is able to automatically start and warm the engine at any set time on the alarm clock.
To enable the auto-start function on the alarm, check the current time setting on the key chain and set the desired engine start time, programming the alarm keychain to the desired time and turning on the alarm clock. The enabled alarm mode on the display of the keychain is indicated by the icon. The engine start time is calculated as the difference between the alarm time and the current value of the time. Programming an alarm clock must be considered that only dozens of minutes are taken into account for autorun in time.
Example. Current time by keychain 7:18 PM. Set time alarm clock 7:20 PM. Starting the alarm clock will occur exactly after 10 minutes.
After checking the current time and set the alarm, set the cursor to the icon and click 2 keychain. 1 Siren signal and 1 outbreak of dimensions follow. The keychain will give a melodious beep. On the display, the icon is displayed, indicating together with the icon included the autorun mode on the alarm. The LED will flash a series of 2 outbreaks.
Simultaneously with the first turning on the function, an automatic start of the engine and its heating during the programmed time will occur. If there is no need to warm the engine you can stop the engine while clicking on the 1 keychain button. Another engine start will occur during the shown on the alarm clock. The presence of a keychain in the zone of alarm at the time of autorun on the alarm clinic is not required.
Note. The engine start time on the alarm clock and the response time of the alarm can not accurately not coincide as such a autorun takes into account the time of multiple only dozens of minutes.
To turn off the autorun function on the alarm, re-set the cursor to the icon and press the 2 keychain button. The keychain will give a melodious beep, the icon will disappear.
Note. When a power transducer + 12V, the alarm does not remember the installation of the engine start mode on the alarm.
Remote Extension of Engine Operation
To prompt extension of the running engine running time by 10, 15 or 20 minutes, set the cursor to the icon and press the 2 button the required number. Each new press, accompanied by 1 siren signal, 1 flash of the dimensions and a melodic signal keychain, increases the engine warming time for 5 minutes. The maximum engine operation time can be installed 20 minutes. At the same time on the display the keychain displays the total time remaining until the engine is stopped. If in the alarm, the engine heating is programmed without time limit, then the activation of the extension function can be used to limit the engine operation. In this case, the extension of work time leads to an automatic restriction of engine operation time. The engine will work 20 minutes and will be stopped.
Preparation of the car to the movement (shutdown of the security mode without stopping the engine)
To turn off the security mode without stopping the engine, briefly press the 1 keyword button. The keyboard display shows the condition of the vehicle with the disabled protection mode and the luminous icon.
Within 30 seconds, open the door, paste the key to the ignition lock and turn on the ignition. Disconnect the parking brake. 1 outbreak of dimensions will follow. Car ready for movement.
Remote engine stop
Without shutting down the security mode
To stop the running engine without shutting down the security mode, press and hold the 1 keychain button until 4 siren signals are appeared, 4 outbreaks of the size or melodic keychain signal. On the display, the vehicle is displayed on the state of the vehicle with the security mode, the icon _ will go out.
With shutdown of security mode
To stop the running engine with the shutdown of the security mode, press the 1 keychain button twice. The first press must be long, before the appearance of 4 signals of sirens and 4 outbreaks of dimensions. The second press should be short-term. In response, 2 siren signals will follow, 2 flash outbreaks and a melodic keychain will sound. The keyboard display shows the condition of the vehicle with the disabled security mode, the icon will go out.
Recording codes Brecks
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
- Turn on the ignition.
- Press and hold the Valet service button until 4 siren signals appear.
- To record the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
- Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
- Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.
Attention! When recording new key chains, you must overwrite both old, otherwise they will be deleted from the system's memory.
Programming functions and auto alarm installations
Some functions and installations of auto alarms can be changed using a service button and a keychain without the need to access the center block. The list of functions is shown in the table below.
Programming procedure Next:
- Turn the ignition and press the service button 6 times.
- Turn off the ignition. Flash outbreaks will follow, and 6 sirens signals indicate input to programming mode will be performed.
- Press the service button the required number times equal to the number of the selected function. Each pressing of the service button will be accompanied by the lighting of the LED indicator and short beeps, indicating the number of the currently selected function. Each fifth pressing a long beep.
- For 10 seconds, press 1 or 2 keychain (0.5 sec) or for a long time (3 sec), depending on the desired state of the selected function. A confirmation will follow 1, 2, 3 or 4 short Siren sounds and a keychain, depending on the function set function.
- To go to the next function, press the service button, and then press the keyword button to set the desired function value. Repeat this procedure for all functions requiring changes.
- To exit the programming mode, step ignition or wait for the automatic system output. The confirmation will follow 5 outbreaks of dimensions.
Note. When programming an alarm with an additional keychain function of the buttons 1 and 2 of the main keychain 3 and 4 additional keychain are performed.
Programming modes using the VALET service button
Some signaling modes can be turned on or off without using remote control key chains using the VALET service button.
The list of modes is shown in the table.
Silent The table marked the factory setting of alarm.
The procedure for programming the operation modes of the alarm is as follows:
- Turn off the ignition.
- Press the VALET service button the required number of times corresponding to the programmable mode. Each press of the service button will be accompanied by the lighting of the LED indicator.
- Turn on the ignition. Sirena short signals will follow. According to the table below, the number of sirens signals can be judged by the choice of programmable mode.
- To turn on or off the programmable mode, press the VALET service button again one or twice. In confirmation of the mode, 1 siren signal follows, in confirmation of the mode shutdown - 2 siren signals.
- Turn off the ignition. 5 outbreaks of dimensions will follow, confirming the output from the programming mode.
Note. When you turn on the daily autorun mode, the engine will start immediately after the ignition is turned off. You can turn off the engine using a control keypad.
When powering + 12V, the alarm does not remember the mode setting daily launch Engine.
The SRARLINE A9 security complex is characterized by the presence of such functions as autorun, anti-primilation, as well as panic and others. A9 contains the sections needed for mounting and setting up the system. Before starting the installation of the complex, you should carefully examine the management and think about the location of the components.
[Hide]
Technical characteristics A9.
Model of automotive signaling Starline Twace Has characteristics:
- operating frequency of the radio transmitter - 433.92 MHz;
- radius of signal feed communicative keychain (with display) - 600 m;
- radio reception by the pager signals submitted by the head unit - 1200 m;
- the distance of the auxiliary control panel is not more than 15 m;
- type of sand sensor design - piezoelectric element;
- the permissible temperature of the head unit is from minus 40 ºС to plus 85 ºС;
- voltage on power terminals - not higher than 18 V and not lower than 9 V;
- current taking by alarm in standby mode - 0.25 mA.
The stated flow and reception distances are achieved only in the open space. In urban development and with no interference, the reception distance is reduced several times.
The design of the Tweez A9 head unit mounting boards allows the operating current values \u200b\u200bindicated in the table.
Equipment
The mounting set includes:
- a keychain-communicator equipped with a liquid crystal screen and a receiver-transmitter for two-way communication;
- auxiliary key chain, working only on the transmission of signals;
- the main unit, which includes the control processor and the relay module;
- antenna module (with an additional transmitter and temperature sensor);
- temperature sensor B. motor compartment;
- adjustable shock sensor;
- control diode;
- tuning and service button with wiring;
- control key of the anti-label function;
- terminal dispersion;
- a set of connective harnesses;
- technical documentation, including the Installation and Setup Guide.
A9 alarm is supplied in a cardboard box, the components are laid in a foam substrate, protecting parts from shocks.
Photo Gallery
The photo shows the type of components included in the alarm set.
General Type of Supply Set
Dismantled with car set Additional control panel Main keychainMain features
Key features provided by alarm:
- The security complex creates several individual protection zones by car. Separate zone is protected by electrical circuits to ensure the start and operation of the engine. End switches are triggered with unauthorized unlocking doors and lever release parking brake. The shock sensor performs the protection of body panels and glasses from damage applied. Additionally ensures the protection of the chains and the ignition lock.
- The head processor unit has a non-volatile memory that saves the state of the system when the power is turned off.
- Built-in anti-primilation mode. It is activated by a button on the keychain or a separate key set.
- Panic mode with remote activation.
- Functions of an additional immobilizer and built-in turbo-timer.
- Automatic start and heating of the motor at a distance and on the laid program.
- It is possible to extend work power aggregate With the keychain.
Installation Instructions
- Installation of the complex is carried out on vehicles equipped with electrical scheme direct current With a voltage of 12 V. The negative pole is connected to the bodybuch.
- All connection work is carried out with disconnected battery terminals.
- Before turning off the power, you need to get acquainted with the recommendations of the car manufacturer relating to the system of inflatable airbags and standard radio (device encoding).
- The elongation of wiring harnesses should be carried out by a conductor from a similar material with a cross section of no less source.
- The wire connection is recommended to be disappeared, and then protected by a tape or shrink tube.
The literacy of the layout and accuracy of the installation depends on the further operation of not only alarm, but also the entire electronics of the car.
What do you need?
The minimum set for mounting includes:
- instructions for Starline A9 on installation and configuration;
- self-tapping screws or screeds (preferably several sizes);
- bolts M6;
- wrench or end heads (set);
- plastic blades;
- broach for wires through the engine shield and car interior;
- drill and set of metal drills;
- installation and insulation materials;
- pulbs for removing isolation if you need to eliminate wiring.
Connection schemes
Below are the main component connection schemes. Detailed information is available in the Installation Guide.
General compound scheme Auto-starting module Block of the Central Castle Solding sensors
Step-by-step action
Approximate component installation sequence:
- Disable terminals from acb. For this, the wrench must be loosen the clip at the battery output.
- Place the processor block system in the hidden cavity of the car, protected from moisture access. Usually, the node is placed inside the instrument panel, on the removal of the aircraft climatic installation. The location is selected in such a way as to eliminate the flow of condensate on the wires inside the connector. The block is fixed to the metal frame of the panel with screws or tie through the regular attachment points. Installation is allowed using bilateral tape.
- Place an antenna node on the inner surface windshield At a distance of at least 45-55 mm from metal panels of the body. If the glass has a metallized film, the module is recommended for free space. Only in this case the maximum range of the transmitter and the receiver is achieved. When installing antenna, avoid places exposed to sunlight. This is due to the presence within the temperature sensor module. Overheat item will report inaccurate information.
- Install the temperature sensor on the block or motor head using a regular bracket. The hole is designed for the M6 \u200b\u200bsize bolt. The installation point should provide a good thermal contact, because this data runs autorun.
- To place Siren under the hood. The node is installed by a shore down at a point inaccessible from the bottom of the car or through the wheel arch. If the owner uses autonomous siren, it is necessary to provide unhindered access to the larch of the Deactivator Castle.
- Sensor hit in the cabin. Mounting place should not prevent access to adjustable potentiometers.
- Install an indicator diode on dashboard or facing front racks. Details are allowed to drilled in advance with a drill hole.
- Thinking through the installation location and mount the buttons of service and anti-grab. The location of the devices should provide quick access to them.
- Install end switches on doors. Decorative upholstery is removed using plastic blades.
- If it is necessary to establish end swipes under the hood and lid of the trunk. When installing, it should be gap within 3 mm and more between the contacts (with covered covers). With a reduced distance, the risk of false positives occurs. The place of installation of the opener should not be in the zone of the cluster of rainwater.
- Using the broach, pave the wiring to the main alarm elements. The gasket route must be kept on the removal from the ignition system and other interference sources.
- Connect wiring harnesses in accordance with the schemes. The head module should be connected last.
- Imagine all connections.
- Turn on the power and program the system in accordance with the recommendations set forth in the instructions.
User's manual
Download user manual and installation StarLine A9
Designation of buttons and icons on the keychain
The purpose of the button A (nearest to the antenna is mainly with the icons of locks on an additional communicator):
- switching on and off protection (including when a power unit running);
- direct autorun and motor stop (only on the main keychain);
- search for a car (together with the B button).
The B button (average on the main remote and with the key icon on optional) is used for functions:
- confirmation of the label selected by the cursor;
- unlocking the luggage compartment;
- auto-starting and engine operation time (optional only);
- choosing a autorun mode (on an additional remote), etc.
Button with (with an open trunk icon) is used for:
- cursor movement;
- shutdown signal sounds;
- keychain settings (including buttons a);
- timer programming;
- machine search (for an additional console).
The D button installed only on an additional remote control is necessary in some cases:
- silent system management;
- enabling additional functions (collaborated with other keys).
The screen has labels of functional and information destination. Functional icons are selected by the cursor method and pressing the buttons turn on or disconnect various modes of operation. Information indicators displays the current status of the functions of the security complex.
Display with labels on keychain Starline A9.
List of functional labels on the screen:
- A - mapping the function of the anti-grab;
- B - the work of Dopcinal 3;
- C - automatic launch of temperature values;
- D - turning on the motor according to the data from the alarm clock;
- E - engine launch at a distance (keychain);
- F - switching on and off protection without filing Siren signals;
- G is the standard mode of operation (with lilac);
- H - disabling shock sensor at a distance;
- I - service mode;
- J - Displays the temperature in the cabin, as well as a survey of the condition of the car;
- K - the work of Dopkanal 2;
- L - remote control Electric drive lock of the luggage compartment.
Information icons:
- 1 - the state of the battery installed in the keychain;
- 2 - inclusion of DPKANA 2;
- 3 - automatic launch depending on the ambient temperature;
- 4 - working force unit;
- 5 - the lid of the trunk;
- 6 - open the terminal side doors;
- 7 - vibration;
- 8 - tuning mode;
- 9 - the function of automatic resetting of the protection of active;
- 10 - protection without feeding sound signals when alarm;
- 11 - standard protection regime (with lilac);
- 12 - open the hood ender;
- 13 - Detection of a strike on the body or windows (various mapping for the first or second sensitivity zone of the sensor);
- 14 - indication of the active parking brake;
- 15 - turning on locking locks on the doors;
- 16 - disabling lock lock;
- 17 - indication of the standby mode, in which only the receiver of the control panel is active;
- 18 - turns on when sending a command;
- 19 - There is a challenge from the car's salon;
- 20 - actively reduced energy consumption by keychain;
- 21 - ignition activation;
- 22 - inclusion of alarm clock;
- 23 - indication of time after lunch RM;
- 24 - similarly - before dinner AM;
- 25 - Start on the signal from the alarm or daily;
- 26 - Displays additional information;
- 27 - selection of temperature measurement scales;
- 28 - Indication of the countdown timer.
How to set up a key chain
The setting sequence is:
- Press the button with select the desired function icon.
- Drown and keep the key from for six seconds during which the buzzer will give a double, and then a triple signal.
- Check the operation of the programmed function by pressing the button A. If the owner is required to change the key assignment, the rewriting procedure has a similar view.
Only the first button (a) of the main console can be adjusted. The owner can choose and assign options for this key unlimited number. The standard solution is to set to enable / disable security mode.
The button B does not have a hard binding to execute any command. It is used to confirm the function selected using the C key. Additional control panel is not programmable.
Installation of watch
The procedure is as follows:
- Drive the C button and hold it until the dual signal is fed and started flashing the indicator field of the clock on the screen.
- You can change the value by pressing a (zoom) or in (reduce). For an accelerated clock translation, the button hold is used.
- Press and similar to set the value of minutes.
- Re-use the C button to hold the sound signal confirming the output from the setting. It is possible to automatically exit programming, waiting a few seconds, during which you should not press the keys.
Entering the alarm data memory is somewhat different from the clock setting:
- Drink the button C and hold it until the dual signal is supplied.
- Clicking on with choose a closure label, after that it will flash the configuration field for the awakening time.
- By analogy with the clock, make the value of the signal on.
- After that, an additional an alarm on / off will appear in the menu. To activate, pressing on A, for shutdown - on V.
Active alarm clock on the STARLINE A9 keychain screen is displayed by a burning label. When triggered, a melodic signal is supplied, which is interrupted by pressing on C.
Setting up autorun.
In order for the owner to use autorun, you need to configure the transmission type when installing the head unit. On the housing of the node there is a connecting loop that must be cut (in the case of mechanical transmission). If an automatic is used on the car, then the loop remains closed. The type of motor is laid when programming block. For the correct launch of a diesel engine, a pre-warming of candles is required, so the starter response delay is set.
Before you need to perform the conditions:
- turn off the ignition;
- raise the parking brake lever;
- close all body elements equipped with trumps from alarm;
- install the program neutral position of the box of the box (only on the mechanical transmission, not required on the machine).
Brief instructions for setting neutral in memory block:
- Stop the car on the site of the scheduled parking lot, leave the ignition active.
- Translate transmission control lever to a neutral position, and then activate the parking brake.
- Disable ignition. With the correct procedure, the engine will continue to work.
- The owner has 0.5 minutes to leaving the cabin of the vehicle. After closing the door, you need to activate the mode of protection according to the standard diagram. The motor will stop instantly either continue to work within the turbotimer mode. If the owner does not include protection, the engine will operate 0.5 minutes or before turning off the programmed turbo-player.
The neutral installation procedure is performed before each alleged auto start.
On some cars there are features of the design, requiring activation of support for the operation of the power unit:
- After stopping the car and translating the lever of the box to neutral, you must press and hold the button A on the keychain.
- Wait for a triple outbreak of overall lights and turn on the melody to the built-in buzzer. The label of the functioning motor is activated on the screen and the operating time will be displayed. In the case of deactivated turbotimer, the text of the type "R00" is included.
- Disable ignition and remove the key from the lock, the power unit must continue to work.
- Further actions are identical to the usual neutral setting (described above).
On alarm clock
Before starting, you need to set the clock and the alarm value.
The setup procedure is simple:
- Button with select the desired icon and confirm the execution of the KE key
- Wait for the supply of a single signal with lilac and dimensions, after which the melody will be played. Two labels will be active on the screen, and the diode will start working a series of two outbreaks.
Starting an alarm clock provides for a single warming of the power unit in the programmed time.
The start time of the power unit according to the alarm clock and the moment of inclusion of the alarm itself does not exactly match. The reason is the rounding of minutes to a dozen during the operation of the autorun.
By timer
Programming is as follows:
- Choose the cursor method the desired shortcut and confirm the action.
- A confirmation will be a single beep of lilac and a flash of light alarm lamps.
- Immediately after that, the first start and engine warming will occur. Repeat launches will be performed 24 hours after the first start time. In case of an error, at least one start, an automatic cancellation of the subsequent heating of the power unit occurs.
Timer Start is the ability to run a power unit daily at a certain time. With an unsuccessful start, the function is turned off, it must be activated again.
By temperature
Step-by-step programming is as follows:
- Move the cursor to select the desired icon on the channel screen.
- Confirm the selection of the function by pressing the button. Get a confirmation signal of the melody, at the same time it should work outward light alarms, and a short siren beep will sound. The display is activated by the mode icon and the threshold temperature value is displayed. An additional confirmation will be an indicator diode that will go into operation mode of three outbreaks.
If you want to deactivate the function, then this is done according to an identical procedure. Confirmation is a double sound and light signal feed, ringtone buzzer and disabling the label on the screen.
When the motor start starts, the alarm uses information from the sensor installed on the engine block or in the engine compartment. The sensor has four settings in the range from -20 ºС to -5 ºС. Additionally, the operating time of the motor and the number of repeated launches, which can not be more than 12 per day. There is also a time limit between starts - at least 1 hour. At the same time, it occurs from the moment of the operation of the power unit, the duration of the heating period does not affect the settings.
The owner should be remembered by two rules for using autorun temperature:
- numerous motor starts lead to the battery discharge;
- if an unsuccessful engine start attempted, the continuation of the cycle is automatically canceled.
How to bind a new key chain to Staline A9?
Step-by-step instruction:
- Enable the ignition of the car, and then click and hold the login button in the settings.
- After filing four beeps, the alarm is released to release the button.
- Take a key chain and press two buttons at the same time. On the main remote, the A and B key clicked, on the additional - C and D. Confirmation of it in memory will be a short signal filed by a lilac complex.
- Repeat the previous item for all programmable devices. It is important to withstand the time interval between the keychains in memory, which should not exceed five seconds. In case of violation, the programming procedure is automatically interrupted. The console number in memory is displayed by the number of confirmation of the beeps.
- After recording the last code, exit the setup mode by turning off the ignition. It should be five times to work out external light alarm.
- Check the performance of the remote controls.
In memory of the head block of the system keychains is required if additional remote controls are purchased. In total, it is possible to bind four communicators, when you try to write the fifth, it is deleted from the memory cell of the first device. This is due to the cleaning of the storage module, so new and old consoles should be prescribed.
The video tutorial on the reference of the console to the STARLINE A9 system is provided by the "Raccoon and Panda" channel.
Advantages of alarm
The advantages of the security complex include:
- function of automatic start of the power unit;
- an additional channel that allows you to expand the system functionality;
- built-in temperature sensor inside the car cabin;
- ease of installation and settings;
- loud built-in buzzer buzzer.
disadvantages
According to the reviews of the owners, the alarm has disadvantages:
- there is no possibility of performing repeated starts through programmable time intervals;
- small radius of receivers and transmitters in urban conditions;
- the command encoding is made according to an outdated algorithm that is easily intercepted and decoded;
- cases of acquisition of alarm with an incorrectly operating head unit are noted;
- weak housing keychain, the support elements of the buttons are destroyed;
- software malfunctions are possible.
How much is?
The approximate cost of the STLINLE A9 signaling is indicated in the table.
Video "Programming SRARLINE A9 alarm"
An example of setting up the STLINLE A9 security package is presented in the videot of Anton AUTO.
