Installation is designed for washing outdoor vertical and horizontal surfaces. truck vehicles, buses, trolley buses and trams.
Installation operation is allowed in a closed room with a temperature ambient from +1 to +40 ° C.
| type of instalation | |
| Installation performance, aut., Gr.Avt. / Hour | 6-20 |
| Number of vertical brushes | 4 |
| 125 | |
| Rod Toka | 3 ~ / 50Hz / 380 V |
| Power consumption, kW | 9,7 |
MPa (kg.С / cm2) |
0,3 - 0,7 (3 - 7) |
| Water consumption for sink one |
500 |
| 6-9 | |
| 5000 - 5280 - 3710 | |
| Installation weight, kg | 5330 |
Semi-automatic Washing Installation PMU-1 (PSK) with a horizontal brush
Stationary washing installation PMA - 1 Designed for surface washing heavy trucksbuses. The sink consists of four vertical brushes and one horizontal brush. Brushes are mounted in a durable frame made of welded profile pipelines. Vertical brushes carry out a mechanized sink of side surfaces. Horizontal - flushing the front, rear and upper parts of vehicles. The rotation of the dual brushes is carried out in different directions, which allows rinse the surface in hard-to-reach places. The brush consists of a brush pipe and the screws attached to it, easily replaced brush elements with a length of 295 mm, 100 mm wide. Installation management performs one operator from the control panel.
Performance - 6 cars per hour.
| type of instalation | Stationary, semi-automatic |
| Installation performance, avt., Gr.Avt. / hour |
6 |
| Number of vertical brushes | 4 |
| The number of horizontal brushes | 1 |
| Rotation frequency brushes, rpm / min. | 125 |
| Drive unit | motor deuctor |
| Pressure in water supply pipelines, MPa (kg.С / cm2) |
0,3 - 0,7 (3 - 7) |
| Overall engine power, kW | 9,7 |
| Water consumption for sink one c. car / bus, liters |
500 |
| The speed of movement of the gr. Automobile, bus in the process of washing, km / h |
4-9 |
| Dimensions of the installation (w x in x d), mm | 3000 - 4800 - 5100 |
Semi-automatic washing installation of buses and trolleybuses PMU-A / T-7 (PSK)
The installation is designed for the mechanized sink of external, vertical surfaces of trolleybuses and car-type buses.
Operation of the installation is allowed in a closed room with an ambient temperature from 1 to 40 ° C.
| type of instalation | Stationary, semi-automatic |
| Installation performance, avt., Troll. / hour |
20-30 |
| Number of vertical brushes | 4 |
| Rotation frequency brushes, rpm / min. | 170 |
| Brushes drive: | eL.Tigator AIR 90 L 6 1.5 kW: 1000 rpm. |
| Pressure in water supply pipelines, MPa (kg.С / cm2) |
0,3 - 0,7 (3 - 7) |
| Overall engine power, without engine water pump drive, kW |
3,0 |
| water pump engine power, kW | 4,0 |
| Water consumption for a sink of one bus, trolleybus, Lithrov |
500 |
| Bus Movement / Trolleybus in the process of washing, km / h |
4-9 |
| Dimensions of the installation (w x in x d), mm | 4000 - 3500 - 3500 |
| Installation weight, kg | About 1200. |
 |
The semi-automatic washing of trolleybuses works in conjunction with the conveyor. The conveyor is designed to ensure uniform movement of trolleybus in the process of washing at a speed of 7.6 m / min. Operation of the conveyor is allowed in a closed room at positive ambient temperatures. Operation on the conveyor:
|
Portal Washing (PSK)
Description:
The installation consists of the following parts:
- The contour of the preliminary wizard of the front, side, rear parts vehicle And the bottoms with wheels:
The outline consists of 2 vertical racks, a height of 4.5 m with high-pressure nozzles with fan spraying and lower horizontal installation of the bottom and wheels.
The pipe wiring represents a single contour from pipes 20mm with nozzles installed on it for washing vertical surfaces and the bottom of the vehicle.
The pressure of 26-30 bar with a total water consumption of 250 l / min, provides a vertical multistage pump with a power of 15kW XVM series production "ESPA". - The circuit of applying a detergent solution on the front, side and rear parts of the vehicle. The outline consists of 2 vertical racks, a height of 4.5 m with nozzles for applying a detergent solution. The operation of the contour provides the horizontal pump K20 / 30 4kW.
- The outline of the final wizard is identical to the contour of the preliminary reconstruction.
- Control panel for operation in automatic and manual modes.
The location of the contours of the attached scheme.
The setting also includes 2 5m3 polyethylene tank for clean water, and 2m3 for detergent solution. Automatic tank filler water supply valves provide float valves.
The contour of the pre-wizard and the outline of the final wash work from one pump and the tank.
Switching is carried out by an electroclap automatically.
The principle of operation of the sink is as follows:
The vehicle drives up to the installation, for 2m runs on the pedal log, the red light light turns on on the left vertical rack, the vehicle stops. Pumps are included and the contours of the pre-wizard and the application of the detergent solution are started. After 10-15 seconds light up green light, the vehicle begins to move with a minimum speed through these 2 contours.
Without reaching 2m to the contour of the final wrap, the vehicle runs the wheel to the pedal log, the red light light on the left side of the circuit lights up, the pumps of the first two circuits are disconnected, the vehicle stops. After 4 minutes, the green light lights up, the high pressure pump is turned on, the vehicle is starting to move and drives the contour at the minimum speed.
Technological cargo washing - Makes it possible to remove dirt remnants from the car before conducting a diagnostic examination or maintenance. Made without the use of any chemistry. The main assistant is AVD (high pressure apparatus), allowing a high-pressure water jet to knock down the dirt from wheels, body and cabins of a passenger car or truck. By time, this procedure takes from 15 to 40 minutes, depending on pollution.
Contactless cargo washing - AND used special compositionsforming an active cleansing foam. The pneumatic sprayer inflicts a layer of such a substance and cleansing the contaminants due to chemical processes. It is worth noting that the properly selected composition of the foam is safe for LCP and structural elements of the car. The time of this washing is from 25 to 50 minutes.
In addition to the cargo sink, we have the opportunity to give a prime appearance and passenger cars. Washing dimensions, as well as high pressure devices, calculated on trucks allow you to maintain sedans and hatchbacks faster and better than on ordinary sinks. To any client, a convenient expectation zone in which there is a coffee machine and the ability to charge the phone. We regularly track the market and guarantee the optimal price for your car washing. Come and see for yourself!
Cargo sink services for passenger cars
|
Passenger, crossovers |
SUVs, minivans, minibuses |
|
|
Technological washing |
||
|
Express washing with foam + mats |
||
|
With wipping (drying) + mats |
||
|
Complex (foam, drying, vacuum cleaner, wet cleaning) |
||
|
Vacuum cleaner salon |
||
|
Cleaning trunk (vacuum cleaner) |
||
|
Dry cleaning of the 1st seating |
||
|
Dry cleaning 1st door |
||
|
Dry cleaning trunk |
||
|
Washing DVS (with chemistry) |
We offer to use our new lineup of equipment and units for high-performance car wash / trolley buses and other motor vehicles With rectangular bodies contours.
| We offer to install equipment that can rinse up to 500 units of equipment daily. Own production and team of professional installers makes it possible to guarantee the speedy implementation of your plans to modernize the responsible stage in the technology of commercial transportation of passengers. Construction material Sink system - AISI 304 stainless steel. On the left is available viewing of the rollers of the system of the system of buses and trucks AVIK BW-01 / TW-01, mounted at different stations of buses. The station on the bottom roller was mounted in 2013, the top - in 2018. Cost of the system of car wash and commercial vehicles |
Same, own production Allows us to optimize the basic system for working brushes, and create a cleaning complex Maximum suitable for your park of buses or minibuses.
Minimum requirements for the installation of this system:
- 13.0 m in length with pass-through pass,
- 6.0 M width,
- 6 m height
- Estraging 7 kW / 380 V / 3 f,
- compressed air, 1/2 ", 8-10 bar
- Water supply and sewage by project.
The washing procedure looks very simple (see Hashe):
- the driver independently enters the minimum speed to the post of washing
- Automation determines the presence of the bus and includes the filing of the shampoo on the application arch
- Continuing to move forward the bus crosses the following pair of sensors and includes a brush block
- The program of operation of the brush module is aimed at full coverage of the contour with a double passage along the side walls
- The process of the washing ends with rinsing the bus with clean water from the arc of the rinsing
The design of the brush module and the arches of the application of reagents and rinsing are made of stainless steel, the control valve and sensors operate from 24 V, minimizing the risk of personnel electric shock. The controller allows you to track the modes of operation of the aggregates and leads the statistics of the operation of the complex.
The complex works in fully automatic mode, leaving the operator only control over the amount of detergent shampoo in the barrel.
If there is a rearview mirror mirrors on the front of the bruise or trolleybuses and not folding if necessary, you will have to abandon the possibility of automatically washing the front of the body. These are restrictions of travel technology. But the solutions of this problem exist - the system can be recycled by contactless high-pressure modules for washing the front (and rear as necessary) part of the TC.
As options to this complex, we can offer the installation of contactless modules for flushing wheels, bottoms and roofs. Adding contactless car wash units will also question the recirculation of water is sharper. We can help here - depending on the needs, we have several options for recycling systems.
If necessary, the bus drying system can be added to the system. This is done in consistently after washing, the body is processed by drying reagent or prepared by the water "Spot Free", after which the bus falls under the arch with the installed high-pressure fans that create air flow with a speed of more than 200 km / h.
Block with suspended fans for drying trucks and buses.
Block of drying commercial vehicles on a manual sink or on the road from the portal or tunnel washing of a travel type.
Drying unit on domestic fans.
Power: 7.5 kW fans, 380V / 50
Bearing stainless steel structures.
"It tries not only to maintain the highest level of services, but also to constantly expand their list. Along with the sink of passenger cars, dry cleaning salon and car wash "Megapolis M" offers its customers a service associated with a sink of buses. After all, neat and tidy appearance The bus is the face of the carrier. Among other things, the periodic washing of such a large transport allows you to save the good performance of nodes and units as long as possible, because a significant amount of dirt accumulates, and thanks to the timely washing, you can reduce costs for costly repairs.
Buses at Megapolis M stations - a fully automated complex of work, during which not only high-level equipment is used, but also a number newest technologiesas well as foaming means. During the washing of buses is cleared of contamination not only the vehicle body, but also cleaning, dry cleaning and salon washing. So, passengers such buses do not have to doubt the high quality of the services provided by the carrier if they are in the sparkling cleanliness of the cabin.
On the car's houses of Megapolis M, it is possible to clean even the most difficult-to-reach places of the engine and the bottom, and it is not necessary to fear any damage from all kinds of pollution. paint coating. Due to the fact that the square of the Meshopolis M car washes is large enough, you do not have to languish in the queues and long wait for the end of work. It will be performed not only very high quality, but also quite quickly. On average, the bus washing will take about 20 minutes. First, a transport foam will be applied to it, which is designed to soften pollution, then it will be melted with a stream of high power water, and then a solution of polymer wax will be applied.
Employees of Maker "Megapolis M" are professionals of their case, so any bus will be washed as much as possible and quickly. If you want your buses to be the perfect reflection of your transport company, Choose the car wash "Megapolis M", and then your customers will never doubt the high quality of your work. And Megapolis M employees, in turn, will make every effort so that your buses are pleasantly surprised and pleased your customers with your neat appearance.
archive
Sink of large-sized transport and manipulators
Recently, the number of specialized sinks for large-tonnant trucks Continuously grows.
Washing tilt trucks
With the modern development of machine-made services to provide cleanliness a passenger car It is not difficult, but the washing of tilt trucks, as well as another heavy truck and large equipmentAs long as the difficult task is.
The procedure for washing tank trucks
The complexity of the tank washing process is that obsolete methods for cleaning tanks with hot steam are quite expensive and long-term (large amount of water, considerable consumption of electricity, several swap cycles, etc.).
Transportation of people is a very responsible work, the main purpose of which is that passengers remain as satisfied with the service provided. As it is customary to speak on clothes, and this is as true as possible in the provision of services for the transportation of passengers. Agree, if you have a chic, comfortable modern bus with all the conditions for a safe journey, but what will the customer response be, if this "liner" is filled with dirty or dusty? The whole effect will be spoiled due to a trifling problem. Therefore, high-quality services of the washing of buses in Moscow are pretty in demand.
There is no such bus that we would not wash!
Thanks to the existing modern specialized washing complex and highly qualified personnel, we will cope with any task. Our masters know all the subtleties of bringing to the brilliance of buses. different types and sizes. It is worth noting that compliance with the correct sequence of the external washing of the bus is a guarantee of its flawless look.
- The primary treatment of water jet is carried out in order to remove large dirt, particles of road dust, sand, reagents and insects. After all, there will be a thorough processing special brushesand if this is not done, then education small scratches On the body can not be avoided. It is important that the Wozer cracker checked completely removed the large particles of dirt or not before it processes the next operation.
- Then the process of "washing" or creating a steady layer of special foam on the buses body. IMPORTANT! Here it is necessary to use only high-quality and certified car chemistry, so that the foam remove the dirt and did not leave behind the traces of the so-called divorce.
- The specialist with the help of sliding brushes removes traces of dirt and various chemical divorces that are located on the lacquer-colorful bus coverage. A special telescopic brush device and optimally selected stiffness of the bristles will provide glossy purity in any, even hard-to-reach places.
- Further, it is flushed a thick foam layer using modern devices of a contactless car wash under high pressure. Without their use, it is impossible to completely wash off auto chemistry from the bus, and the remaining soap solution can harm the paint and varnish coating.
At this stage, the washing procedure does not end, and goes into the second stage, which is important for the carrier, as the buse's salon appearance reflects the level of attitude to passengers. Our experts fulfill the entire range of work in this direction in a short time.
- Start wet cleaning from the ceiling, as all the water will drip down and if there was a floor cleaning or chairs, then you have to repeat this procedure again. In order not to damage the seats, our masters will wear special protective covers.
- For travelers, the most interesting occupation is to consider what is happening from the window of the bus and if they are dirty, the pleasure of the trip will be spoiled. Therefore, it is important to create the perfect cleanliness of the windows.
- Next, workers remove protective covers with seats and begin to vacuuming each of them, moving from the back to the seat. If the skin coating is treated with a special solution that eliminates the smell.
- Then wipe plastic handles of seats, as well as the floor washed, completing the full cleaning of the cabin.
At the request of the client, we will bring impeccable order and in the driver's cockpit to create comfortable conditions during the trip. An additional service in the dry cleaning of the cabin is offered. We create the atmosphere of comfort and care in your bus affordable priceAnd passengers will certainly appreciate it.
Convenient location in Moscow
The car wash is located two hundred meters from Food City in six hundred meters from the Moscow Ring Road. It is equipped with sufficient parking sites and a comfortable waiting area.
