RECOMMENDED FUELS Unleaded petrol HYONDE vehicles must use unleaded petrol with an octane rating of 91 RON (Research Method, "Normal") or higher. The use of leaded gasoline will lead to failure of the catalytic converter (exhaust gas) and to failure of the emission control systems. It can also lead to ...
For greater convenience, all locks of your car can be unlocked with one key. However, since the doors can be locked without using a key, it is recommended that you carry a spare key with you in case you accidentally lock the key inside your own vehicle. Keys that unlock all car locks Key number To prevent unauthorized persons from finding out your key number, this number ...
The immobilizer is designed to minimize the possibility of theft of your vehicle. EMERGENCY OPERATIONS If the immobilizer warning lamp blinks for 5 seconds after turning the ignition key to the "ON" position, this indicates that the engine start interlock system is malfunctioning. You will not be able to start the engine without performing operations for ...
This system is designed to prevent unauthorized entry into the vehicle. This system has three states: the first is "Ready", the second is "Alarm" and the third is "Disabled". When the anti-theft system is triggered, the sound alarm (siren) is turned on and the direction indicators start flashing. Ready state Park the car ...
Warning Before driving (especially if there are children in the car), make sure that all doors are securely closed and locked and cannot be accidentally opened from inside the car. Also, with the correct use of seat belts, door locking helps prevent passengers from being thrown out of the vehicle in the event of a traffic accident. Before...
Location of the rear door child safety lock Your HYONDE vehicle is equipped with a rear door lock ("childproof lock"). If the lock levers are in the locked position, the rear doors cannot be opened from the inside of the vehicle. It is recommended to use the rear door locks if there are small children in the rear seat. For h ...
The prevention Adjust the seat only when the vehicle is stationary. Failure to do so could result in loss of vehicle control and road traffic accidents, which could result in vehicle damage, serious injury or death. Adjusting the fore-and-aft position of the front seat
To raise or lower the door glass, rotate the power window handle clockwise or counterclockwise. Directions of rotation of the power window handle to raise or lower the glass ELECTRIC WINDOWS The power windows only operate when the ignition key is in the ON position. The main power window switches are located ...
This system controls the passenger door locks from the driver's door lock. When the driver's door is locked, the passenger door locks are automatically locked. If the tailgate is open when the inner door lock interlock button is pressed, the door will be locked after being closed. If the front door is open when the interior door lock button is pressed, ...
1.10 Safety Precautions
Seat belts must always be worn by the driver and all adult passengers, as well as children large enough to be properly fastened with the seat belts. Following basic safety precautions can minimize the risk of serious injury in the event of a road traffic accident. Infants and young children In some countries, it is mandatory to use a baby ...
1.11 Caring for seat belts
It is not allowed to remove or modify the seat belt system. In addition, care must be taken to ensure that seat belts and related parts are not damaged by seat hinges, doors or improper use. Warning When returning the rear seat back to the upright position, be careful not to damage the tape or the belt buckle of the safety ...
The height of the front seat belt anchorage can be adjusted in one of 4 positions. Location of the locking button and direction of movement for adjusting the height of the upper belt anchorage When adjusting the seat belt anchorage, adjust it at a sufficient height to ensure that the belt is firmly in contact with your shoulder and at the same time that the belt DOES NOT TOUCH your neck. What...
Fastening the seat belt To fasten the seat belt, pull it out of the retractor and insert the belt strip (latch plate) into the buckle until you hear a click. Fastening the seat belt buckle The seat belt automatically selects the correct length only after you manually adjust the waist belt so that it fits snugly around your thighs. NS...
To fasten the two-point seat belt, insert the latch tab into the buckle. Locking the lock will be accompanied by a characteristic click. Check that the seat belt buckle is secure and that the seat belt is not twisted. Fastening a two-point seat belt buckle (rear center seat belt) Adjust ...
When transporting children in a vehicle, they should always be seated and strapped in the back seat to minimize the risk of injury in the event of a traffic accident, sudden braking or turning. Traffic accident statistics show that children who are restrained with an appropriate device are less likely to be at risk in the back seat than in the front. D ...
The car is equipped with an additional passive safety system (airbags) SRS. The presence of this system can be identified by the "SRS AIR BAG" lettering on the steering wheel airbag cover and on the front passenger side panel trim above the glove compartment. The SRS system consists of airbags installed under the pads ...
Instrument panel 1 - side deflector of the ventilation system; 2 - headlight range control switch; 3 - rear window cleaner / washer switch; 4 - combined switch for headlights and direction indicators; 5 - sound signal and additional passive safety system - driver's airbag; 6 - windscreen wiper / washer switch ...
The fuel gauge arrow shows the approximate fuel level in the fuel tank. The fuel tank has a capacity of 45 liters. Fuel gauge ...
Warning Do not open the radiator cap when the engine is hot, as the cooling system is under pressure, and opening the cap can lead to the release of hot fluid, which can cause severe burns. Wait for the engine to cool before opening the radiator cap. The transition of the instrument arrow from the permissible range towards the "H" position indicates ...
1.21 Odometer (trip meter)
The odometer shows the total distance in kilometers or miles that the vehicle has traveled and is very useful for monitoring periodic maintenance intervals. ...
1.22 Daily mileage counter
The daily mileage counter shows the distance traveled for a single trip or for a certain period of time. Press the reset (zero) button to reset the counter. ...
The tachometer displays the engine speed in revolutions per minute (rpm). The tachometer can help you select a more economical driving mode, and also warns when the engine speed is exceeding the maximum allowed value. Tachometer Warning While driving, follow the tachometer readings. Arrow showing frequency ...
Direction indicator switch When the combination switch is moved downward, the direction indicators on the left side of the vehicle will flash. When you move the combination switch up, the direction indicators on the right side of the vehicle will flash. After completing the turn, the switch will automatically return to neutral and, at the same time, the direction indicators ...
The switch can be set in the following three positions: 1 - intermittent brush movement; 2 - slow movement of the brushes; 3 - fast movement of the brushes. Windshield Wiper Switch Positions Warning To prevent damage to the wiper system, do not attempt to clear heavy snow or ice, but accumulated snow or ice must ...
The rear window wiper and washer are activated by pressing the switch located on the instrument panel. When a button on the switch is pressed, washing liquid is supplied to the rear window. Do not operate the rear window washer for more than 15 seconds or when there is no fluid in the washer reservoir; this could damage the system. Rear Window Wiper and Washer Switch Location ...
The headlight beam corrector is designed to adjust the angle of inclination of the headlight beam depending on the number of passengers and the weight of the cargo transported by the vehicle. Headlamp leveling position The higher the headlamp leveling switch position number, the lower the headlamp beam will be directed. Always use the headlight range control switch to adjust the distance illuminated by the headlights (to ...
Hazard warning light switch location The flashing light acts as a warning to other drivers to act with extreme caution when approaching, overtaking or passing near the vehicle. The system should be used when absolutely necessary or when the vehicle comes to a stop near the edge of the road. Press the switch in any off position ...
Location of the button for turning on the rear window heater The heater is designed to eliminate frost, fogging and icing of the rear window inside and outside the car. The ignition must be on to turn on the heater. The heater will turn on when the rear window defroster button is pressed. Heated rear window will turn off automatically after 15 minutes or when off.
To turn on the fog lights, press the switch. The front fog lamps can only be switched on when the headlamp switch is in the first or second position. Location of the front fog lamp switch ...
Press the switch to turn on the rear fog light. The rear fog light can be switched on when the headlights are on. Location of the rear fog light switch ...
Electronic clock The electronic clock has three control buttons with the following functions: HOUR - Press the "H" button to set the hours. MIN (Minute) - Press the "M" button to set the minutes. RESET - Press the "R" button to reset the minutes to zero. In this case: - pressing the "R" button between 10:30 and 11:29 changes until ...
The location and direction of pressing the cigarette lighter to turn it on The cigarette lighter can be used when the key in the ignition switch is in the "ON" ("On") or "ACC" ("Optional Equipment") position. To use the cigarette lighter, press the cigarette lighter handle all the way. When the cigarette lighter is heated, it will automatically ...
Front ashtray To open the front ashtray, pull it out using the handle. To remove the ashtray from its slot for cleaning, press down on its inner spring-loaded tab and pull it completely out of the rails. The ashtray light is on only when the vehicle's exterior lighting is switched on. ...
Rear ashtray To open the rear ashtray, pull it out from the top edge. To remove the rear ashtray from the cleaning slot, lift it up and out from the top edge. ...
Cup holder A cup holder is located on the front main console to hold glasses and bottles in the openings provided. To use it, pull it out by the top file. Warning If the cup holder is not in use, put it back in its original position. Do not place foreign objects on the cup holder. Such items can be thrown into the passenger compartment and can waste ...
Removal of the sun blind PERFORMANCE ORDER 1. Pull the handle of the sun blind towards its front part, then lower the rear part of the sun blind. Direction of movement of the sun shade removal handle 2. After that, you can easily remove the sun shade. Installation of a sun blind PERFORMANCE ORDER ...
Roof tilt The hatch can be opened and closed manually. PERFORMANCE ORDER 1. Pull the handle down and then forward and up as shown by the arrows in the figure. 2. Press in the center of the handle to lock the sunroof in the open position. 3. After tilting the sunroof, make sure the handle is locked in place. Closing the hatch PERFORMANCE ORDER 1. Pull the handle ...
The interior lighting lamp has a three-position switch that can be set to the following positions: - 014 "MIDDLE" position, the interior lighting lamp comes on when a door is open and goes out when it is closed; - "OFF" "RIGHT" position, the interior lighting lamp does not light up even when any door is open; - "ON" & quo ...
Pull the handle to open the glove compartment. Warning While the car is moving, the door of the glove box must be closed in order to exclude the possibility of injury to the passenger in the event of sudden braking or a road accident. Pulling direction of the handle to open the glove compartment ...
Manual Mirrors For convenience, the exterior mirrors are equipped with a remote control. They are adjusted using a control lever installed in the front lower part of the door glass. Direction of movement of the lever for adjusting the position of the outside rearview mirror Before driving, make sure you have a good view behind you from the left and ...
Pressing the switch for the heated rear window also activates the heating of the outside rearview mirrors. The location of the button for turning on the rear window defogger and outside rear-view mirrors To eliminate fogging or icing, press the rear window defroster switch. The glass of the mirrors will be heated, which will provide a good view from behind in any weather. To...
To fold down the door mirrors, push them towards the rear of the vehicle. Pressing direction for folding the outside rearview mirror The outside side mirrors can be pressed against the vehicle door windows when parking in tight spaces. ...
The car is equipped with an interior rear-view mirror. To select the "night" (anti-glare) position, pull the lever at the bottom of the mirror toward you. In this position, the glare from the headlights of cars driving behind you at night is reduced. Location of the day / night switch in the interior rearview mirror ...
Always apply the parking brake before leaving the vehicle. When the parking brake is applied with the ignition key in the ON or START position, the parking brake warning lamp in the instrument cluster comes on. Before you start driving, make sure that the parking brake is completely disengaged and that the warning lamp is off ...
For added convenience, the entire seatback can be folded down or the rear seatbacks can be folded down separately. To unlock the backrest, pull up on the release handle and then tilt the backrest forward. Position and direction of pulling out the release knob to unlock the back of the right rear seat Position and direction of pulling out the lever ...
Warning When the car is moving, the rear door or the boot lid must always be fully closed, since if it is opened or slightly opened, poisonous exhaust gases can get into the car interior. To open the tailgate or boot lid, turn the key clockwise in the lock and then lift the tailgate or boot lid with your hands. Forward ...
If someone is locked in the luggage compartment, they can open the lock from the inside by pulling the red lever on the lock cover. Location of the emergency release lever for the boot lid lock We recommend that the car is always locked and the keys are kept out of the reach of children, and that parents explain to their children that it is dangerous to play in the luggage compartment of the car. ...
The tailgate or tailgate can be opened by pressing the tailgate or tailgate lock actuator lever, after which it must be lifted up by hand. To close the tailgate or boot lid, fold it down and then push it down until it locks into place. To make sure that the tailgate or trunk lid is securely locked, try lifting it again. ...
The fuel filler cap can be opened from inside the vehicle by pulling up on the fuel filler cap release lever located on the floor on the front left side of the vehicle. Location of the lever for remote opening of the fuel filler cap Warning If you cannot open the fuel filler cap ...
To unlock the bonnet lock, pull the bonnet lock actuator toward you. Directions of pulling the handle of the drive of the lock of the bonnet While pressing the safety lever, raise the bonnet. Directions for pressing the bonnet safety lever Support the bonnet with a support rod. To close the hood, remove the support bar and secure it in the latch. Slowly lower the hood to the ...
Your HYONDE is equipped with sun visors for the driver and front passenger to help prevent glare from the front and sides. Sunshades are fitted on both sides on all vehicle models. Tilt the sun visor downward to reduce glare or protect from direct sunlight. The vanity mirror is mounted on the back of the sunscreen ...
To adjust the height of the steering wheel, do the following: PERFORMANCE ORDER 1. Press the lever down to unlock the lock. Directions for pressing the lever to lock and unlock the steering wheel 2. Raise or lower the steering wheel to the desired position. 3. After adjusting, securely lock the steering wheel by lifting the lever up ...
AUDIBLE SIGNAL FOR VEHICLES WITH AIRBAGS Location of the horn on the airbag steering wheel To sound the horn, press the horn symbol located on the steering wheel. Check the horn regularly to make sure it works properly. SOUND SIGNAL OF VEHICLES WITHOUT AIRBAGS Sound signal ...
The heating and ventilation system panel is shown in the figure. Heating and ventilation system panel: 1 - fan operating mode switch; 2 - knob for selecting the ventilation mode; 3 - knob for adjusting the air temperature; 4 - switch for selecting the air intake mode. FAN OPERATION MODE SWITCH The switch is designed to turn the fan on and off ...
The air purifier is located in the evaporator in front of the glove compartment and is designed to prevent dirt from entering the vehicle interior and to clean the air. Evaporator and Fan Air Purifier Location Warning Replace the filter every 20,000 km or once a year. When operating a car in difficult road conditions, more frequent inspection and replacement is required ...
How the car stereo works Signals in the AM and FM bands are transmitted through repeaters located around the city. The signals coming from them are received by the car's antenna. When a strong radio signal is received at the antenna of the radio receiver, the state-of-the-art audio system provides high-quality reproduction. However, in some cases, the incoming signal is not strong and does not ...
Fixed-stem antenna The vehicle uses a detachable fixed-stem antenna to receive AM and FM signals. To remove the antenna, rotate it counterclockwise, and to install it, rotate it clockwise. Directions of rotation when removing and installing a removable antenna with a fixed rod Warning Before washing the car in automatic ...
1.59 Driving a car
The prevention It is dangerous to start the engine at idle speed in the garage, even if the garage doors are open. Do not allow the engine to run in the garage longer than is necessary to start the engine and drive the vehicle out of the garage. If it is necessary to run the engine at idle for a long time, when there are people in the car, park the car in an open, well ventilated ...
Starting the engine If your Hyundai car is equipped with a manual transmission, shift the gear lever to neutral and fully depress the clutch pedal. If your Hyundai car is equipped with an automatic transmission, move the selector to the "P" ("Parking") position. To start the engine, insert the key into the ignition lock and turn ...
Normal engine start PERFORMANCE ORDER 1. On a car with a manual transmission, set the gear shift lever to the "N" ("Neutral gear") position and depress the clutch pedal. On a car with an automatic transmission, move the selector lever to the "P" (Park) position. Warning Make sure ...
The position of the gear lever is the traditional five-speed forward, as shown in the figure. Positions of the gear shift lever Warning When engaging the reverse gear, after the car has come to a complete stop, hold the gear shift lever for at least 3 s in neutral position. After that, move the lever to the rear transmission position.
Mode selector lever positions for automatic transmission The HYONDE high-performance automatic transmission has four forward gears and one reverse gear. It has the usual gearshift pattern shown in Figure 117. At night, in the first position of the multifunction switch on the gearshift pattern, the corresponding light will be ...
1.64 Anti-lock braking system
CORRECT BRAKING TECHNIQUES Before driving after parking, make sure that the parking brake is released and that the brake warning lamp is off. Brakes may become wet after driving on water or washing your car. Wet brakes are very dangerous because the car will not be able to stop quickly. To dry the brakes, apply light pressure while driving, ...
1.65 Economical driving
By following these guidelines, you can save fuel and increase your vehicle's mileage without refueling: - Drive smoothly and avoid sudden accelerations. Try to move at a constant speed and do not accelerate before stopping; - try to maintain the speed of the traffic flow in order to avoid unnecessary changes in speed. Avoid driving in heavy traffic conditions as much as possible.
1.66 Smooth cornering
Avoid braking or changing gears when cornering, especially on wet roads. It is best to take turns with a slight acceleration. If you follow this advice, you will minimize tire wear. ...
1.67 Driving in winter conditions
More severe operating conditions in winter lead to more severe wear of parts and other problems. To minimize winter operating problems, you should follow these guidelines: Driving on Snow or Ice Driving in deep snow may require winter tires or snow chains. If it is necessary to install winter tires, it is necessary ...
1.68 Towing a trailer or vehicle
Warning Refrain from towing a trailer during the first 2000 km of run to ensure the break-in of parts of a new car. Failure to observe this precaution could result in serious engine or transmission damage. Towing hooks Choose the right combination of towing hitch, making sure its position matches the anchorage point.
1.69 Engine does not start
If the engine does not crank with the starter or cranks very slowly If the car is equipped with an automatic transmission, move the selector to the "P" or "N" position and apply the emergency brake. Check the wire connections to the battery terminals to be sure they are clean and tight. Turn on the interior lamp. If the lamp is lit with ...
PERFORMANCE ORDER 1. Check the fuel level in the tank. 2. Check the connections of all wires of the ignition system, coil and spark plugs. Reconnect disconnected or loose connections. Connections of wires of the ignition system, coil and spark plugs 3. If you smell gasoline, the air-fuel mixture may have been over-enriched (`` ...
1.71 If the engine stalls while driving
PERFORMANCE ORDER 1. Gradually reduce the speed of the car, moving in a straight line. Pull carefully off the road to a safe place. 2. Turn on the alarm. 3. Activate the alarm. ...
Starting with connecting cables can be dangerous if done incorrectly. Therefore, to avoid personal injury or damage to the vehicle or battery, follow the procedure below. Keep all sources of flame or sparks away from the battery. The battery generates hydrogen, which can explode if exposed to ...
1.73 If the engine is overheated
If the arrow of the coolant temperature gauge is in the overheating zone, you feel a loss of engine power or hear a loud hiss or knocks, the engine may be overheated. In this case, you must do the following: - turn off the road and stop the car in a safe place; - put the selector in position "P" ("Parking") (automatic ...
Towing a vehicle with the drive wheels raised off the ground As a general rule, vehicles should be towed with the drive wheels raised off the ground. If, due to significant damage to the vehicle or other circumstances, the vehicle cannot be towed with the drive wheels raised, use a cart. Towing a vehicle with a manual transmission ...
The prevention Before towing, check the fluid level in the automatic transmission. If it is below the HOT (Hot) mark on the dipstick, add fluid. If you are unable to add fluid, you must use a towing cart. In case of emergency towing, when it is not possible to use the services of a tow truck, attach the towing cable ...
1.76 Prevention of corrosion and periodic maintenance
Car Corrosion Protection Using the most advanced technologies and methods of corrosion protection, HYONDE produces high quality cars. However, in order to provide long-term corrosion protection for your Hyundai car, your help and assistance is also required. Common causes of corrosion The most common causes of corrosion on your car are: - road salt, dirt and moisture ...
The Vehicle Identification Number (VIN) is the number used to register vehicle ownership. It is located on the dividing wall between the passenger compartment and the engine compartment on the engine side and on the floor panel in the luggage compartment on the right side. Vehicle Identification Number (VIN) Location Engine Number The engine number is stamped on the cylinder block ...
1.78 Vehicle specifications
Dimensions For 4-door models For 3/5 door models Overall length 4235 4200 Overall width 1670 1670 Overall height (unloaded) 1395 1395 Wheelbase 2400 2400 Front wheel track 1435 1435 Rear wheel track 1425 1425 Steering Type Rack and pinion Steering wheel play 0-30 mm Steering rack travel 134 mm Pump type hydraulic booster ...
A book in a series of full-color illustrated DIY car repair manuals. The manual contains design features of units and systems of Oka VAZ-1111, -11113 vehicles, as well as their modifications for disabled drivers. The main malfunctions, their causes and remedies are described in detail. Disassembly and repair processes are illustrated and annotated. A separate section is devoted to car care. The Appendices contain tools, lubricants and operating fluids, lip seals, bearings, tightening torques for threaded connections, and an electrical diagram. The book is intended for drivers who want to repair a car on their own, as well as for service station workers.
On our website you can download the book "Oka VAZ-1111, -11113 with engines 0.65; 0.75. Device, maintenance, diagnostics, repair. Illustrated manual" free of charge and without registration in fb2, rtf, epub, pdf format, txt, read a book online, or buy a book from an online store.
Cars VAZ-1111 "Oka" and their modifications - front-engined, with a transverse engine, front-wheel drive four-seater. Body - two-volume, supporting structure, all-metal, welded. Engines - two-cylinder, in-line, four-stroke, carburetor, with a volume of 0.65 liters (currently not produced) and 0.75 liters, with a capacity in accordance with GOST 14846-81 (net) from 25.9 to 33.0 hp. Engines of the VAZ-1110 model were produced in a small batch. Cars were produced by Kamsky (KamAZ) and Serpukhovsky (SeAZ) automobile plants. At present, the production of Oka cars remains only at the Serpukhov Automobile Plant, which also produces modifications for the disabled. Vehicle model and number, engine model and spare part number are indicated on the nameplate attached to the upper cross member of the radiator frame.
Ignition system
Spark moment sensor:
1 - holder of the front roller bearing; 2 - sensor support plate; 3 - screen; 4 - the spring of the weight of the centrifugal regulator; 5 - regulator weight, 6 - driving plate of the centrifugal regulator; 7- oil seal; 8 - roller; 9 - clutch; 10 - bushing of the rear end of the roller; 11 - driven plate of the centrifugal regulator; 12 - vacuum regulator; 13 - connection for vacuum supply; 14 - thrust; 15 - contactless sensor (Hall sensor); 16 - case; 17 - a block of wires of the Hall sensor; 18 - cover; a - scheme of the centrifugal regulator; ἁ - ignition timing.
Details of the spark moment sensor: 
1 - clutch; 2 - case; 3 - vacuum regulator of the ignition timing; 4 - stuffing box; 5 - contactless sensor (Hall sensor); 6 - the driving plate of the centrifugal regulator; 7 - weight of the centrifugal regulator; 8 - roller of the driving plate; 9 - spring; 10 - driven plate of the centrifugal regulator with a screen; 11 - lock washer; 12 - sensor support plate with bearing; 13 - bearing lock plate; 14 - front bearing holder; 15 - cover.
The ignition system is non-contact. Consists of a spark torque sensor, switch, ignition coil, spark plugs, ignition switch and high and low voltage wires. The spark moment sensor is of type 5520.3706 (until 1989 the sensor of type 55.3706 was installed) with built-in vacuum and centrifugal ignition timing controllers. It sets the moment of sparking depending on its initial setting, the number of revolutions of the crankshaft and the load on the engine.
The reading of the control pulses is based on the Hall effect. There is one impulse for each revolution of the crankshaft (two for each revolution of the camshaft). The initial ignition timing for the VAZ-1111 engine is 1 ± 1 ° to TDC, for VAZ-11113 - 4 ± 1 ° to TDC. You can check the performance of the Hall sensor with a voltmeter by connecting it between the terminals of the green and white-black wires. Slowly rotating the roller of the spark moment sensor, we follow the readings of the voltmeter. The voltage should change sharply from the minimum (no more than 0.4 V) to the maximum (no more than 3 V less than the supply voltage). If the steel screen with slots touches the sensor (determined by a slight jamming or scratching sound during the rotation of the roller, as well as after partial disassembly of the spark moment sensor), check the axial play of the roller (no more than 0.35 mm, adjustable by the selection of washers) and the fit of the screen on roller.
Replace the assembly if necessary. A defective Hall sensor cannot be repaired and must be replaced with a new one (except for a wire break between the sensor itself and the block on the spark moment sensor housing). You can roughly assess the serviceability of the vacuum regulator directly on the car. With the engine running, disconnect the vacuum hose leading to the regulator from the carburetor fitting. If you now create a vacuum in the hose (you can use your mouth), the engine speed should increase, and when the vacuum is removed, decrease again. The vacuum should be maintained for at least a few seconds if the hose is pinched.
Visually, you can make sure that the vacuum regulator is working properly by partially disassembling the spark torque sensor (see "Removing and disassembling the spark torque sensor", p. 86) and applying a vacuum to the inlet fitting at the regulator. In this case, the screen of the sparking torque sensor should be rotated by an angle of 10 ± 1 °, and when the vacuum is removed, it should be returned without jamming. Accurate testing and tuning of the vacuum and centrifugal ignition timing controllers is carried out at special stands. It is not recommended to do this at home. If the vacuum regulator fails, it is replaced; if the centrifugal regulator fails, the spark moment sensor is replaced.
The switch type 3620.3734, or 36.3734, or HIM-52 opens the power supply circuit of the primary winding of the ignition coil, converting the sensor control pulses into current pulses in the ignition coil. The switch is checked by an oscilloscope using a special technique, if you suspect a malfunction (engine interruptions, shots at the muffler), replace it with a known good one. Do not disconnect the switch connector while the ignition is on - this can damage it (as well as other components of the ignition system). Ignition coil - two-lead, dry, type 29.3705 - with an open magnetic circuit, or type 3012.3705 - with a closed magnetic circuit. Data for verification: resistance of the primary winding at 25 ° C - (0.5 ± 0.05) Ohm, secondary - (11 ± 1.5) kOhm. Insulation resistance to ground - not less than 50 megohms. Spark plugs - type A17DVR, or A17DVRM, or their imported counterparts (with interference suppression resistors with a resistance of 4-10 kOhm). The gap between the electrodes should be within 0.7-0.8 mm (checked with a round wire probe).
High-voltage wires - type PVVP-8 with distributed resistance (2000 ± 200) Ohm / m or PVPPV-40 with distributed resistance (2550 ± 270) Ohm / m. Do not touch high-voltage wires while the engine is running, as this may result in electrical injury. It is also forbidden to start the engine or allow it to operate with a broken high-voltage circuit (wires removed) - this can lead to burnout of insulation, failure of electronic components of the ignition system. Ignition switch type 2108-3704005-40 or KZ813 with anti-theft locking device, interlocking against re-starting the starter without first turning off the ignition. When the key is turned to the "ignition" position, voltage is applied to the control input of an additional relay of type 113.3747-10, which, in turn, supplies voltage to the ignition coil and the switch. This relieves the ignition switch contacts (see also Electrical Equipment).
Non-contact ignition system diagram: 
1 - ignition switch relay; 2 - ignition switch; 3 - fuse box; 4 - switch; 5 - spark moment sensor; 6 - ignition coil; 7 - spark plugs.
A book in a series of full-color illustrated DIY car repair manuals. The manual contains design features of units and systems of Oka VAZ-1111, -11113 vehicles, as well as their modifications for disabled drivers. The main malfunctions, their causes and remedies are described in detail. Disassembly and repair processes are illustrated and annotated. A separate section is devoted to car care. The Appendices contain tools, lubricants and operating fluids, lip seals, bearings, tightening torques for threaded connections, as well as an electrical diagram. The book is intended for drivers who want to repair a car on their own, as well as for service station workers.
"Oka" VAZ (SeAZ, KamAZ) -1111 - Soviet and Russian minicar of the first group of an especially small class (segment A - mini cars). The car was developed at the Volga Automobile Plant, produced at VAZ, ZMA, KAMAZ and SeAZ in 1988-2008.The Oka car began to be developed in the late 1970s at the Serpukhov Automobile Plant (SeAZ) to replace the obsolete S3D motorized carriage. Then the development was transferred to AvtoVAZ, where the project turned from a motorized carriage into a full-fledged, albeit small, car.
A very modern, for its time, body design and corresponding to the ideas of cars of this class in the world, was created at UGK AvtoVAZ by the designer (at that time, an artist-constructor) Yuri Aleksandrovich Vereshchagin. It should be noted that this development is one of the few cases when a domestic car (USSR) was not the result of direct borrowing and adaptation of a foreign analogue.
The Japanese micro-car Daihatsu Cuore of the 1980 model is considered the prototype of "Oka", but apart from the basic concept of body design and a number of technical solutions, the structure of "Oka" was actually developed anew (especially the power unit and chassis).
Initially, "Oku", like Daihatsu Cuore, was supposed to be equipped with an original 3-cylinder engine, but due to its unavailability at the time of the start of car production, a 2-cylinder engine was used, which in fact was equipped with two balancing shafts and counterweights on the flywheel and pulley " half "1.3-liter engine VAZ-2108. The all-new 3-cylinder engine was ready by the early 90s, but the industry crisis prevented its implementation.
The first full-scale mockups of the new car were created in October 1982. After that, three experimental series of the car were produced, each of which had differences from the previous one. At the beginning of 1987, an experimental-industrial batch of VAZ-1111 was produced. Serial production of "Oka" began in 1988.
Address: Moscow city , 1 Nagatinsky proezd, house 13 (M. Nagatinskaya)
Working hours: daily 9: 00-23: 00
Professional body repair of any complexity: (straightening dents, removing scratches, completely restoring the geometry of the body). - Repair of internal combustion engines, chassis; - Painting; - Stack work; - Maintenance; - Comprehensive diagnostics.
answers: 1
"Our" cars are in good hands!
Service request
Address: Moscow city , 2nd Nagatinsky proezd, house 6, building 1 (metro Nagatinskaya)
Working hours: 9-00 22-00
Gearbox repair car service. Repair of the VAZ 2101-2107 gearbox _____ 2500r. Repair of the VAZ 2108-21099 gearbox _____ 2500r. Repair of the VAZ 2110-2115 checkpoint _____ 2500r. Repair of the checkpoint Kalina, Priora _____ 2500r. Repair of the GAZEL-VOLGA checkpoint _____ 2500r. Our Car Service is fully equipped for the repair of VAZ, GAZ, GAZEL, UAZ, IZH ODA, ...
Car service "Superstore"
replies: 2 276
SuperService
Service request
Address: Moscow city , Shcherbinka, st. Cosmonauts house 1, building "B", building 33 (metro Buninskaya alley)
Working hours: 10.00-19.00
For the clients of the Karpis website - a DISCOUNT at the Superstor car service - 30%. Autoservice Superstor performs: - maintenance, - repair, - car body repair, - muffler repair, - air conditioner repair and refueling. Constantly in stock spare parts for Chevrolet Aveo, Chevrolet Lanos, Chev ...
answers: 248
Complete service for your car
Service request Address: Moscow city , Rostokinsky proezd house 3, building 5 (metro VDNKh)
Working hours: 8.00-22.00
We do everything related to Mitsubishi cars. Here you can find used and new spare parts of this manufacturer. Any repair of any complexity. Our company carries out in a short time at low prices repairs of any complexity of Japanese-made cars. Repair types: locksmith ...
Silencers and catalysts: installation, replacement, repair
Service request
Address: Moscow city , Yuzhnoportovaya house 15, building 23 (metro Kozhukhovskaya)
Working hours: Daily from 10.00 to 19.00
Direct flow-Service is a specialized station for the repair of car exhaust systems. A team of professionals will perform work of any complexity for the repair, replacement of mufflers, catalysts, corrugations. Installs a lambda probe emulator (oxygen sensor blende). Will make a direct-flow exhaust system. Station...
Locksmith repair and maintenance
Service request
Address: Moscow city , Kantemirovskaya house 59 A (metro Kolomenskaya)
Working hours: seven days a week from 09:00 to 21:00.
LLC "Techcenter Maximum" carries out maintenance, diagnostics and all types of work on the repair of the engine, chassis and electrical parts of the car, as well as the installation of additional equipment and complex body repair in accordance with the manufacturer's technology. Repair and service zone "...
answers: 51
We remove 97-100% of damage on the body
Service request Address: Moscow city , Bulatnikovskaya str., 2a (metro Prazhskaya)
Working hours: from 9-00
Removing dents without painting The main activity of the company is the paintless repair of dents on the car body using the PDR technology (Paintless Dent Repair). The technology allows, by 97-100%, to remove damage to the car body, without the need to change and / or paint the elements ...
replies: 2 372
Our specialization is working with transmission
Service request
Address: Moscow city , Ogorodny proezd d4 (metro Timiryazevskaya)
Working hours: from 10-00 to 21-00
Manual transmission repair. - Repair of manual transmissions of any complexity is carried out in Avtorusservice by experienced craftsmen. If you need a high-quality manual transmission repair, call. We repair transmissions for VW, Skoda, Fiat, Citroen, Opel, Peugeot, Ford, BYD, Chery, Chevrolet, Daewoo, FAW, Geely, Great Wall, Honda, Hyundai, Isuzu, Ki ...
replies: 4 280
Our goal is your good mood!
Service request
Address: Moscow city , Dmitrovskoe highway 167s3 (metro Altufevo)
Working hours: from 9-00 to 20-00 daily
We specialize in the repair of foreign cars Mercedes, BMW, Toyota, Nissan, Renault, Volvo, Opel and other brands. Our company has been engaged in car repair for over 8 years. All work is carried out by highly qualified specialists using equipment from leading world manufacturers. ...
Technical center "SEKservice"
replies: 1 176
SEK Service can handle any complex work
Service request
Address: Moscow city , Prospect Mira, house 186 (metro VDNKh)
Working hours: 10-00 to 20-00
Repair of steering racks, Gur pumps. Our company has been working in the field of car service since 1992. and provides a wide range of services for engine repair, car painting, car repair, injector flushing and other car maintenance services. The list of services of our car service can be unlimited ...
TRIAAA
answers: 8
Service requestAddress: Moscow city , Bolshoi Volokolomsky passage, 10 (metro Shchukinskaya)
Working hours: 10.00 to 21.00
straightening without painting using modern technologies tuning, ateliers, any non-standard solutions as well as body molar work repair of bumpers of any complexity local painting polishing of the body
replies: 1 142
Free repairs for OSAGO!
Service request
Address: Moscow city , st. Rabochaya 84, building 4 (metro Ilyich Square)
Working hours: 10-20
Our company has been operating in the car services market for over 15 years. We are professionally engaged in body repair, painting and mechanical repair of passenger cars and commercial vehicles. We also provide: - Service for corporate clients. - Replacement of windshields. - Solution of non-standard ...
Car service "Dils-Auto"
replies: 728
We carry out locksmith and body repair of cars of any complexity !!!
Service request
Address: Moscow city , Dobrolyubov building 1 (metro Petrovsko-Razumovskaya)
Working hours: 9-22
Located in the Butyrsky district (SVAO), AutoTechCenter "DILS AUTO" is pleased to offer you its services for a quick and high-quality repair of your car. We will be glad to offer you the best specialists in bodywork, locksmith, reinforcement, tinning and painting works. Well-coordinated work and worked long ago ...
Autocomplex "Lian-Motors"
answers: 872
Car repair and maintenance at the highest level 7 days a week
Service request
Address: Moscow city , Abramtsevo house 30, building 3 (metro Altufevo)
Working hours: Mon-Sun 9.00-21.00
The Lian-Motors technical center has an excellent locksmith and body shop, four professional car wash stations, and also provides a wide range of services for owners of various car brands. Available for you are tire fitting, engine repair, electrical equipment and fittings, flushing ...
Inexpensive high-quality car service "AvtodeloFF"
replies: 271
"Everything for your car"
Service request
Address: Moscow city , Derbenevskaya house 7, building 19 (metro Paveletskaya)
Working hours: 9:00-22:00
Our service station fully meets the criteria for dealer stations, equipped with the latest diagnostic and repair equipment and all the necessary tools. Customers of a car repair center can count on a full range of services for the repair and maintenance of any models. In our car service we have a ...
replies: 8 477
Sidorov R.Yu.
