Without knowledge of a caring car to buy a spare wheel set - a big problem. The number and diameter of the holes for fastening the disc with bolts are important. If you contact the store and give incomplete information, you will definitely sell it.

For example, the wheels of the wheels of Lancer 10 compared to the 9 generation model is another. Even if the hole diameter seems the same, the difference can be. Deviation in a couple of millimeters eyes will not determine. The wheel will "dress", but it will not be necessary to drive - due to the axial disk offset.

Mitsubisi Lancer 10

Mitsubishi Lancer. X leaves the conveyor in full-time complete sets. Disc parameters are as follows:

Owners of restyling "dozen" if desired can put discs with other parameters. But it is important to take into account that the breakdown of Mitsubishi Lancer 10 should correspond to the one that is in the service book. Ignore the manufacturer's requirements - deprive the guarantees!

Drying wheels Mitsubishi Lancer 9

Lancer models have 9 somewhat different breaks:

What do the figures and letters of marking mean?

We provide decryption on the example of the complete marking of 8.5J × 18 H2 5 / 114.3 ET40 D 67.1:

• 8.5 - Planting width of the disc, in inches,

• J - constructive features Top. The angle of inclination is encrypted, radius of rounding. JJ may indicate the disk for full drive, accordingly, one letter is a sign of a monolon.
• X is the type of construction. X means the rim has a solid design with a base / cast disk.
• 18 - installation disk diameter (in inches).
• H2 - the number of rings holding a tire. H is a reduction from HAMP. Hamp can be single, double (as in example), flat, asymmetric, combined. And maybe there is no one at all.
• 5/114.3 - The first digit of the fraci indicates the number of holes and nuts / fastening bolts. The second to the ratio of the distance of the diameter from the mounting holes of the nuts to the central (hub) hole. In the technical literature, such an indicator is indicated as PCD. In our example, it is equal to 114.3 (the classical value for the tenth lancer).

Conformity PCD.extremely important. Even 2 millimeters of incomprehension will lead to a violation of the characteristics and failures in the work of the chassis. Between 114.3 and 112 you will not notice the difference. Wheel freely sit down in place. But when fixing with nuts, one will delay firmly, and 4 others, losing the center, will go to the lobe of the millimeter to the side. After that, the nuts will be constantly unscrewed when moving - if you are not shifted. If you drag, the wheel will be installed with distortion, which will lead to the biotis and acceleration of the wear of parts. Thread size nuts - M12 x 1.5.

• ET40 - protrusion / departure of the disk;
• D (Dia) 67.1 - the diameter of the hub hole.

There are valid values \u200b\u200bfor each parameter. Changes in parameters within the range will not affect wear resistance and technical parameters vehicle. However, even in machines of one model, but different generations Indicators may be different. Mitsubishi Lancer Wheels The wheels 9 differs significantly from the characteristics of the wheels "dozens".

Saying new wheel disks On Mitsubishi Lancer 9, many motorists blindly trust the calculators of online stores and recommendations of sales consultants. Meanwhile, on sites and in catalogs of conscientious companies, it is indicated that the information provided is not exhaustive and does not guarantee the exact compliance of the manufacturer's requirements.

Installing new wheels - This is a simple and affordable way for most owners a way of correction of car appearance. The design of these accessories can be selected, guided by its own tastes. The remaining characteristics must be observed based on reliable technical documentation. When buying, you should consider all parameters specified in the marking.

1. Landing diameter . It depends on it, what kind of tire you can use in the future.
2. Width rim . It limits the minimum and maximum width tires
3. Departure . This characteristic indicates the distance from the bustal plane of the disk, which it touches the wheel hub, to its longitudinal plane of symmetry.
4. The diameter of the location of the holes Under the mounting bolts. If this parameter is inconsistent, it is simply impossible to install the item on the car. The drilling hole for the mounting bolts is standardized and depends on the other characteristics.
5. The diameter of the central (installation) hole . Ideally, he must coincide with the size landing On the hub. Sometimes manufacturers, calculated on various models Techniques make a hole somewhat more and attached transition rings (inserts).

Used designations

In classical European labeling, the information looks like this: 5.0 × 16 "4 × 113 ET28 D58.4, where 5.0 - the width of the disk, 16" - landing size, 4 × 113 - the number and diameter of the location of the fastening bolts, ET28 - departure, and D58.4 - the caliber of the planting opening.It would seem that everything is simple. But the fact is that original details Mitsubishi Lancer 9 Disc size marked otherwise. Most likely, you will have to face such designation: 15 × 6JJ OFS46,OPC: B41, PCD114.3.The difference is as follows.

• Added marking JJ (letters can be different), clarifying the shape of the rim.
• Number of holes The bolts are not specified at all, and the diameter of their placement is indicated as PCD.
• OPC. - The size of the planting opening.
• Ofs. - Departure.

Try not to get confused

Tuning lovers often do not see a special misfortune in the acquisition of wheels, the size of which differ from the recommended for use. They do not suspect the number of problems that arise as a result of a similar attitude to the technique. What is affected by the size of the discs of Mitsubishi Lancer 9? Judge for yourself.

1. The large diameter wheels involve the installation of tires, the dimensions of which can simply not fit into the space of the wheel arches. Often, this inconsistency makes itself felt already in motion. When the tire suspension is started to touch the elements of the body and the chassis, as a result of which the details are damaged.
2. When developing a car design, engineers perform many complex calculations, trying to achieve optimal work of all components of the equipment. The outer diameter of the wheel directly affects the loads arising from the engine operation, gearbox, gearbox, drive shafts. Together with him, in fact, change transmission numbers Transmissions affecting fuel consumption and dynamic characteristics of the car.
3. Dispensing disk by departure means changing the load on hub bearings, hub and suspension elements. At first glance, insignificant, these changes are the cause of destruction of responsible parts.

Optimally, when Mitsubishi Lancer 9 disks 9 corresponds to the parameters recommended by the manufacturer for a particular configuration of a popular car. Below, the table shows the data for six modifications issued.

Modification index, engine volume (cube cm) and body modification	Landing diameter (inches)	Width rim	Bolt hole layout diameter	Setting hole size (mm)	Departure (mm)
		(inches)	(mm)
CS1A 1300 Sedan.	15	6	114.3	41	46
CS3A 1600 Sedan.	15	6	114.3	41	46
CS3W 1600 WAGON	16	6	114.3	41	46
CS9A 2000 Sedan.	16	6	114.3	41	46
CS9W 2000 WAGON	16	6	114.3	41	46
CT9A 2000 TURBO SEDAN	17	8	114.3	54	38

You should not use this data by selecting the discs for Mitsubishi Lancer 10. There are other sizes.

Materials and production technology

The market offers details made from different materials and on distinguished technologies:

• stamped from steel sheet;
• cast from lung alloys;
• forged from lung alloys.

All listed varieties have their advantages and disadvantages. Much depends on the operating conditions of technology.

1. Stamped discs - inexpensive and unpretentious. They look not too presentable, and their appearance It is necessary to improve, acquiring and installing decorative caps. But in heavy conditions of operation - on roads with a bad coating or in winter - the use of such components is quite justified. They are well withstanding shock loads, and the damage obtained is restored after rolling on a special machine and recovery. paint coating. The main disadvantages are considered fairly high weight and low manufacturing accuracy, worsening balancing.
2. Products cast from lung alloys well balancing and, from aesthetic point of view, look flawless. Their cost is slightly higher than that of steel analogs. But it applies to them to be carefully. Despite the fact that there are repair technologies, when making damage, the part, with a large probability, will have to be sent to the smelter. Disks cast Mitsubishi. Lancer 9 includes regular equipment more expensive complete sets Auto.
3. Accessories made from lung alloys According to the forging technology, beautiful and most expensive. Repair also arise problems. But the strength is no doubt. For conscientious manufacture there are no difficulties and balancing.

Execution option You are free to choose yourself. But to retreat from the parameters specified by the manufacturer. Is that if you know how to make calculations better than the team of engineers of the Japanese concern.

The Lancerix.ru website has already published the parameters of the Disk for Lancer 9. Given the large ascent of this topic of the car owners, we publish another news on the topic "Discs Lancer 9". In this publication, I wanted to show more clearly to show that all the parameters used by the auto owner to select the disks on Lancer 9. All disk parameters are indicated in the figure below, and are presented in the table. So, staten parameters Discs for Lancer 9 depending on the volume of the engine

lancer Lancer 9, l.

PCD (seat hole or drilling)

Diameter disk

ET (departure), mm

Dia (hub diameter), mm

We will analyze the parameters specified in the table, for example, 6JJ × 16 PCD 5 × 114.3, ET46 DIA67.1.
The parameters are decrypted so:
6 - mounting width wheel wheel in inches.
JJ. - wheel rim profile (example: jj, c, ch, hj, etc.). In this letter is encrypted technical information On the closures of the rim of the disk (design, shape, height). The most common types of disc drives and all-wheel drive cars Today are J and JJ. Color rims are influenced by the installation of rubber compensating for weights, as well as resistance to the offset of the tire on the disk in extreme conditions. The differences between the types of clouds denoted by different letters can be minor, but it is impossible to neglect them.
The area of \u200b\u200badjustment of the tire to the rim is very critical, small changes in the tire board profile lead to difficulty and even the impossibility of mounting, as well as to the inability to hold the required pressure inside the wheel.
The designations A and D circuit rim fall under the category "Bicycles, Motorcycles and Scooters" (Cycles, Motorcycles, and Scooters), and also possible in the Industrial Vehicles and Lift Trucks category. Naturally, contours have completely different geometry in the same designation in two different categories.
Crates with the designation S, T, V and W are categories in " Trucks, COMMERCIAL VEHICLES, FLAT BASE RIMS), and the designations E, F G H - to the category "Trucks, wheels with collapsible rim" (Commercial Vehicles, Semi-Drop Center Rims). Obviously, despite the external interchangeability, it is better to choose the parameter recommended by the car manufacturer.
16 - Mounting wheel diameter of wheels in inches.
PCD 5 × 114.3 - the number of fasteners, in this case 5 × diameter on which the centers of the holes are located, and in our case it is 114.3 mm.
ET46. - departure of the wheel plane of the wheel (the plane that the wheel is pressed against the hub), relative to the center of the rim. Departure is like a positive and minus (example: ET40 - a carET-4 "Jeep") is measured in mm. In this case, it is 46 mm.
DIA67,1 - Diameter central openingwhich is responsible for the center of the entire wheel assembly on the car hub. Measured from the partial plane. In our case, equal to 67.1 mm. Many wheel manufacturers make a larger diameter DIA, and transition rings (adapters) are used on the hub.

Mitsubishi Lancer IX SW (CSW) dischair of Mitsubishi 2005 1.6 (98 hp, gasoline). Tools of wheels Mitsubishi Lancer 9

Discs Lancer IX (Lancer 9) - drilling, departure, diameter, width | Mitsubishi Lancer IX, Lancer 9, Wagon, Classic. Disk Disc Mitsubishi Lancer 9

Mitsubishi Dzbashchka Lancer IX SW (CSW) 2007 G.V. 1.6 (98 hp, gasoline). Tools of wheels Mitsubishi Lancer 9

Discs Lancer IX (Lancer 9) - drilling, departure, diameter, width

The Lancerix.ru website has already published the parameters of the Disk for Lancer 9. Given the large ascent of this topic of the car owners, we publish another news on the topic "Discs Lancer 9". In this publication, I wanted to show more clearly to show that all the parameters used by the auto owner to select the disks on Lancer 9. All disk parameters are indicated in the figure below, and are presented in the table. So, regular disk parameters for Lancer 9, depending on the volume of the engine, the following

We will analyze the parameters specified in the table, for example, 6JJ × 16 PCD 5 × 114.3, ET46 DIA67,1. These parameters as follows: 6 - mounting width wheel rim in inches.jj - wheel rim profile (example: JJ, C, CH, HJ, etc.). This letter is encrypted technical information about the rim collar (design, shape, height). The most common types of discs for mono-drive and all-wheel drive cars today are J and JJ. Color rims are influenced by the installation of rubber compensating for weights, as well as resistance to the offset of the tire on the disk in extreme conditions. The differences between the types of clouds denoted by different letters can be minor, but it is impossible to neglect them. The area of \u200b\u200badjustment of the tire to the rim is very critical, small changes in the tire board profile lead to difficulty and even the impossibility of mounting, as well as to the inability to hold the required pressure inside the wheel. The designations A and D circuit rim fall under the category "Bicycles, Motorcycles and Scooters" (Cycles, Motorcycles, and Scooters), and also possible in the Industrial Vehicles and Lift Trucks category. Naturally, contours have completely different geometry in the same designation in two different categories. Color with the designation S, T, V and W are categories in "Trucks, Flat Rimes" (Commercial Vehicles, Flat Base Rims), and the designations E, FGH - to the category "Trucks, wheels with collapsible rim" ( Commercial Vehicles, Semi-Drop Center Rims). Obviously, despite the external interchangeability, it is better to choose the parameter recommended by the car manufacturer.16 - the mounting diameter of the wheel rim in inches.pcd 5 × 114.3 is the number of fasteners, in this case, 5 × diameter on which centers are located Holes, and in our case it is 114.3 mm.Et46 - departure of the wheel plane (the plane that the wheel is pressed against the hub), relative to the center of the rim. The departure is like a positive and minus (example: ET40 - a passenger car, ET-4 "Jeep") is measured in mm. In this case, it is equal to 46 mm.dia67.1 - the diameter of the central opening, which is responsible for the center of the entire wheel assembly on the hub of the car. Measured from the partial plane. In our case, equal to 67.1 mm. Many wheel manufacturers make a larger diameter DIA, and transition rings (adapters) are used on the hub.

Discs on Mitsubishi Lancer 9 Wheels: how to choose

Wheel Discs Lancer 9

Looking for new wheels on Mitsubishi Lancer 9, many motorists blindly trust the calculators of online stores and recommendations of sellers of consultants. Meanwhile, on sites and in catalogs of conscientious companies, it is indicated that the information provided is not exhaustive and does not guarantee the exact compliance of the manufacturer's requirements.

Main settings

The installation of new wheels is simple and accessible to most owners a way of correction of car appearance. The design of these accessories can be selected, guided by its own tastes. The remaining characteristics must be observed based on reliable technical documentation. When buying, you should consider all parameters specified in the marking.

1. Landing diameter. It depends on it, what kind of tire you can use in the future.
2. Rim width. It limits the minimum and maximum width of the tire.
3. Departure. This characteristic indicates the distance from the bustal plane of the disk, which it touches the wheel hub, to its longitudinal plane of symmetry.
4. The diameter of the location of the holes under the mounting bolts. If this parameter is inconsistent, it is simply impossible to install the item on the car. The drilling hole for the mounting bolts is standardized and depends on the other characteristics.
5. The diameter of the central (installation) hole. Ideally, he must coincide with the size of the landing place on the hub. Sometimes manufacturers, in the calculation of various techniques, make the hole slightly more and attached transition rings (inserts).

How to correctly choose discs

Used designations

In classical European labeling, the information looks like this: 5.0 × 16 "4 × 113 ET28 D58.4, where 5.0 - the width of the disc, 16" - landing size, 4 × 113 - the number and diameter of the location of the mounting bolts, ET28 - departure, and D58.4 - Caliber of the planting hole. It would seem that everything is simple. But the fact is that on the original details of Mitsubishi Lancer 9 the size of the disks is marked otherwise. Most likely, you will have to face such designation: 15 × 6JJ OFS46, OPC: B41, PCD114.3. The difference is as follows.

• Added jJ marking (letters can be different), clarifying the shape of the rim.
• The number of holes for the bolts are not specified at all, and the diameter of their placement is indicated as PCD.
• OPC - the size of the planting hole.
• OFS - departure.

Try not to get confused

Tuning lovers often do not see a special misfortune in the acquisition of wheels, the size of which differ from the recommended for use. They do not suspect the number of problems that arise as a result of a similar attitude to the technique. What is affected by the size of the discs of Mitsubishi Lancer 9? Judge for yourself.

1. The large diameter wheels involve the installation of tires, the dimensions of which can simply not fit into the space of the wheel arches. Often, this inconsistency makes itself felt already in motion. When the tire suspension is started to touch the elements of the body and the chassis, as a result of which the details are damaged.
2. When developing a car design, engineers perform many complex calculations, trying to achieve optimal work of all components of the equipment. The outer diameter of the wheel directly affects the loads arising from the engine operation, gearbox, gearbox, drive shafts. Together with him, in fact, the gear ratios of transmissions affect the fuel consumption and dynamic characteristics of the car are changed.
3. Disconnecting disk by departure means changing the load on the wheel bearings, the hub and the elements of the suspension. At first glance, insignificant, these changes are the cause of destruction of responsible parts.

Optimally, when Mitsubishi Lancer 9 disks 9 corresponds to the parameters recommended by the manufacturer for a particular configuration of a popular car. Below, in the table, indicate data for six release

Discs Lancer IX (Lancer 9) - drilling, departure, diameter, width | Mitsubishi Lancer IX, Lancer 9, Wagon, Classic

The Lancerix.ru website has already published the parameters of the Disk for Lancer 9. Given the large ascent of this topic of the car owners, we publish another news on the topic "Discs Lancer 9". In this publication, I wanted to show more clearly to show that all the parameters used by the auto owner to select the disks on Lancer 9. All disk parameters are indicated in the figure below, and are presented in the table.
So, regular disk parameters for Lancer 9, depending on the volume of the engine, the following

lancer Lancer 9, l.

PCD (seat hole or drilling)

Diameter disk

ET (departure), mm

Dia (hub diameter), mm

We will analyze the parameters specified in the table, for example, 6JJ × 16 PCD 5 × 114.3, ET46 DIA67,1. These parameters are: 6 - Mounting wheel width in inch

website

Disk Disc Mitsubishi Lancer 9

discs Lancer

Disclaimed Works Work. Wheel Spacers. Installing on Lancer X. Overview of parameters.

Wheels Lancer 9.

How does the wheel size affect overclocking? (H-AUTO)

Where to see the size of rubber on the car and how to choose the size of the tires (tips from the RDM import)

Buying casting and rubber by 17 inches.

All about MITSHUBISHI LANCER 9

Disks on Lanser

Also see:

• Hyundai Solaris Dimensions Hatchback
• How to remove the rear bumper Daewoo Nexia
• Peugeot fuse diagram 406
• New Skoda Octavia reviews
• Dimensions Renault Duster
• Nissan Murano video
• Fiat Linea Reviews Owners
• Replacing oil in automatic Ford Focus 3 PowerShift
• Honda Crosstur Characteristics
• Lexus Px characteristics

Home »Mitsubishi» Mitsubishi Lancer Disk Disc

det23sad.ru.

What wheels breaking on Mitsubishi Lancer 9

Lancer 9. Valbrem discs. Rubber Bridgestone. Rugs in the salon.

All about MITSHUBISHI LANCER 9

Alloy wheels Yamoto Segun for Mitsubishi Lanser X (Cast Disks Yamato Segun for Mitsubishi Lanser X)

Spacers for disks

Opel Astra GTC. goes away. 1.4T VS 2.0 Lancer 10.

Lancer x gt tuning

Lancer Cedia 4WD Work Viscounts

Replacing studs on rear wheels Machines.Toyota and other brands. (Popular version)

195 Repair brake system on Mitsubishi

Also see:

• Bumper for Suzuki aryio car
• How to turn off the mass on Kamaj
• Sound exhaust BMW x6m video
• Engine protection for Ford Ecosport 2014
• Repair of the steering rack on Mercedes W211
• UM 327 Ford Focus Programs
• How many oil lithres in Dr. Peugeot 206
• Warrow Mitsubishi Pajero 4 EGR
• Engines BMW m and n series
• Kia Rio rear suspension Scheme
• What drives are suitable for Mazda 323
• Volkswagen LT 35 in himself
• Hyundai Stareks out south Korea
• Honda Suspension Accord 7 D2
• Chevrolet Cruze Leather on the steering wheel

Home »Choice» Which wheeled wheels on Mitsubishi Lancer 9

aUTO-ARSELON.RU.

Mitsubishi Lancer IX SW (CSW) Mitsubishi Disk (CSW) 2005 1.6 (98 hp, gasoline)

1. Dzboboltovka.ru.
2. Mitsubishi.
3. Lancer IX SW (CSW)
4. 1.6 (98 hp, gasoline)
5. 2005 G.V.

Find the parameters of the Mitsubishi Lancer IX SW (CSW) disc / 1.6 (98 HP, gasoline).

Table of parameters and breaks of disks Mitsubishi model Lancer IX SW (CSW) 1.6 (98 ls, gasoline) - 2005

• LZ (number of holes)
• ET (disk departure)
• Dia (hole diameter)

Save just in case not to lose!

razboltovka.ru.

Disk breakdown Mitsubishi Lancer 9

Lancer 9. Valbrem discs. Bridgestone rubber. Rugs in the salon.

All about MITSHUBISHI LANCER 9

animation disks on Mitsubishi Lancer 10.mp4

Alloy wheels Yamoto Segun for Mitsubishi Lanser X (Cast Disks Yamato Segun for Mitsubishi Lanser X)

Spacers for disks

Wheel rotation After replacing the Lancer IX caliper repair kit

MITSUBISHI LANCER 9 (skillful handles !!!)

Spacers Starleks 20mm Vektor 35mm

Lancer x gt tuning

Sports cars

Also see:

• Angel eyes Replacing the light bulb on BMW
• Mitsubishi Pajero 3 door years of release
• Repair Moped Suzuki Sepia Video
• How to change the stabilizer bushings on Skoda Octavia Tour
• Starting Heat Heat Chevrolet Cruz
• Cable for bMW diagnostics E34
• Roof trunk for Nissan Almera 2013
• Pixels on dashboard BMW X5 E53.
• Fuel filter for Toyota Camry. V40 2 4.
• Volkswagen conveyor What rights are needed
• Honda XLR 250 valve clearances
• Tom Ford Noir Pour Femme Perfume Water Reviews
• Repairs diesel engine Opel Astra
• How to fix crankcase protection Ford Focus. 2
• Honda Engine Model GX 390

Home »Clips» Disk Tubes Mitsubishi Lancer 9

stk-auto.ru.

Mitsubishi Lancer IX SW (CSW) Mitsubishi Disk (CSW) 10 (98 hp, gasoline)

1. Dzboboltovka.ru.
2. Mitsubishi.
3. Lancer IX SW (CSW)
4. 1.6 (98 hp, gasoline)
5. 2004 G.V.

Find the parameters of the Mitsubishi Lancer IX SW (CSW) 2004, 1.6 (98 hp, gasoline) disk.

Table of parameters and breaks of disks Mitsubishi model Lancer IX SW (CSW) 1.6 (98 ls, gasoline) - 2004

Disk drilling parameters, usually ring up:

• LZ (number of holes)
• PCD (circle diameter of hole centers)
• ET (disk departure)
• Dia (hole diameter)

Save just in case not to lose!

Given the greatest solarity of this topic from the car owners, we publish another news on the topic "Discs Lancer 9". In this publication, I wanted to show more clearly to show that all the parameters used by the auto owner to select the disks on Lancer 9. All disk parameters are indicated in the figure below, and are presented in the table. So, regular disk parameters for Lancer 9, depending on the volume of the engine, the following

We will analyze the parameters specified in the table, for example, 6JJ × 16 PCD 5 × 114.3, ET46 DIA67.1.
The parameters are decrypted so:
6 - mounting width wheel wheel in inches.
JJ. - wheel rim profile (example: jj, c, ch, hj, etc.). This letter is encrypted technical information about the rim collar (design, shape, height). The most common types of discs for mono-drive and all-wheel drive cars today are J and JJ. Color rims are influenced by the installation of rubber compensating for weights, as well as resistance to the offset of the tire on the disk in extreme conditions. The differences between the types of clouds denoted by different letters can be minor, but it is impossible to neglect them.
The area of \u200b\u200badjustment of the tire to the rim is very critical, small changes in the tire board profile lead to difficulty and even the impossibility of mounting, as well as to the inability to hold the required pressure inside the wheel.
The designations A and D circuit rim fall under the category "Bicycles, Motorcycles and Scooters" (Cycles, Motorcycles, and Scooters), and also possible in the Industrial Vehicles and Lift Trucks category. Naturally, contours have completely different geometry in the same designation in two different categories.
Color with the designation S, T, V and W are categories in "Trucks, Flat Rimes" (Commercial Vehicles, Flat Base Rims), and the designations E, FGH - to the category "Trucks, wheels with collapsible rim" ( Commercial Vehicles, Semi-Drop Center Rims). Obviously, despite the external interchangeability, it is better to choose the parameter recommended by the car manufacturer.
16 - Mounting wheel diameter of wheels in inches.
PCD 5 × 114.3 - The number of fasteners, in this case, 5 × diameter on which the centers of the holes are located, and in our case it is 114.3 mm.
ET46. - departure of the wheel plane of the wheel (the plane that the wheel is pressed against the hub), relative to the center of the rim. The departure is like a positive and minus (example: ET40 - a passenger car, ET-4 "Jeep") is measured in mm. In this case, it is 46 mm.
DIA67,1 - The diameter of the central opening, which is responsible for the center of the entire wheel assembly on the hub of the car. Measured from the partial plane. In our case, equal to 67.1 mm. Many wheel manufacturers make a larger diameter DIA, and transition rings (adapters) are used on the hub.