1. Raise the wiper leash and remove the wiper brush from it assembly.
2. Install a new wiper brush assembly, inserting the central part (1) in the groove (2) in the leash of the wiper, so that it snaps into place.
3. Make sure the wiper brush is reliable, slightly pulling it.
In case the wiper cleans the glass poorly, their surface can be labeled or crack, therefore they must be replaced. Attention to avoid damage to the wiper lever or ... Warning - the dangers of the battery carefully read these instructions before starting work with the battery. Keep burning cigarettes or other outdoor fire or sparks as far as possible ...Other online:
Sliding armrests
To move forward pick the front of the armrest (1) and pull it forward to move back to press the armrest back. Caution Do not keep the front of the armrest (1) ...
Clutch excitation coil
Removing the order of execution 1. Remove the clutch sleeve and pulley of the air conditioner compressor. 2. Install the safety tool on the open hole of the compressor shaft. 3. Install the puller on ...
SIMOS 2P Injection Components - Injectors of Injection and Fuel Mainer
If there are suspicion of the malfunction of the injectors, you should not immediately begin with their removal. First, try to clean the injectors by adding a special additive to fuel (ask ...
Replacing janitors by car Kia Rio is made as their wear. Usually, the service life of the coils of janitors is at least a year, after which the rubber tape of the wiper is clogged and deformed. On the windshield, this is reflected in the form of distinctly not washed dirty stripes. If only the cleaning element is impossible to replace, then the janitor, together with the frame, is changing entirely.
The process of replacing janitors is very simple and takes no more than 2-3 minutes, even a novice car enthusiast can cope. Work can be performed in any atmosphere - in the garage, in the parking lot or on the side of the route. It produces in such a sequence: raise and fix the janitor, flexing the latch fixing the janitor on the leash, weching the wiper brush down the hook. Installing a new brush We produce in reverse order.
It is important to remember that the need for replacement may occur at any time, for example on the track while driving, with a sharp deterioration of weather conditions, therefore experienced motorists Always have a suitable replacement in stock so that the items are always at hand.
Attention! This video is not official Instructions and guidance on the repair of the car.
Video with more simple way replacements -
br /\u003e
On some kIA equipment Rio 2011-2018 Hybrid Wipers Denso Wiper Blade are installed, but new wipers are quite expensive, and the replacement of the rubber band is a good way to return the old wipers to life. Gum with Aliexpress will cost only 250-300 rubles per set.
Elastic size for Kia Rio 3 - 26 "and 16" inches (65 mm and 40 mm)
Http://kiariofaq.ru.
How to replace wipers (wiper brushes) on the example Kia Picanto. Or any car with leashes in the form of hooks. Brushes - Lynx. As well as replacing the gum of the wiper brush.
Avtotests, travels here: Er-erka.Ru
It is not well saved, and instead of "janitors" assembly, we change the gum on them. 🙂
For the most impatient: Repair starts at 3:22
Many fresh and actual articles read on my channel Yandex.Dzen Over 9000: https://zen.yandex.ru/over9000
Sign up!
# Over9000 # auto # repairAvto # Over9000 # jannors # rubberries # wiper # brush
Subscribe to My Channel: httpse.com/www.youtube.com/channel/ucioxjdi_pjmd_l95wrx3kvg
And on my second channel about radio-controlled models:
https://www.youtube.com/channel/ucot_a0fynxs-cnntwm0nrcg.
See also:
How to choose Saab 9000? Part 1: Body
br /\u003e How to choose Saab 9000? Part 2: Salon
br /\u003e How to choose Saab 9000? Part 3: Electrician (1/2)
What you need to know in order to change the wipers on your car. Replacing brushes glass windshield cleaner.
How to protect the wheels from theft. Secret bolts (nuts)
We elect and change the wipers on Kia Sportyj.
Wipers Kia Sportsji It can be attributed to the consumables of the car, which sometimes require substitution. In order for the car throughout its service life remained reliable, comfortable and non-hazardous, you need to make it maintenance. Remove the lighting plafof how to remove front bumper kia Rio-3 How to remove the front headlights of Kia. The list of such works is clearly established by the manufacturer, and their list depends on the mileage. Kia Kia Sportage 1, 2, 3, 3 selection and replacement. In addition to the interval of replacement of some details, there are reasons for which the consuming replacement is required earlier.
Kia wiper brushes Sportsji Perform the function of cleaning the heat from dust, dirt, insects, water. How to replace the wipers at Kia Sportage 3. They are rubber tips on a metal frame or without it, which move along the surface of the windshield or rear braid, cleaning them from contamination. Kia Club Kia Club Kia Kia Rio Club Club All about Kia Korean Lovers Club But how to remove wipers. During operation and under the influence of loads and external environment wipers may fail. This is manifested in reducing the quality of the glass cleaning, the appearance of foreign sounds, jamming or breakage. All this can be avoided if you replace the brushes on new on time.
Selection of new janitors on Sportage
To choose the right brushes on this car We need to take into account several features:
Read the same way
- construction of fastening
- size Kia janitors Sportsji
- manufacturer of wiper brushes
The manufacturer recommends using original kia wipers, their 988503w000 details code (amkm0139). You can order them in any online store, which is available. original spare parts Kia and Hyundai. How to remove wipers at Kia Sportage 3? How to remove the cover of the mechanical lock kia Sportage. You can also use high-quality substitutes from reliable manufacturers. It is important to use products of companies that have proven themselves and having positive reviews Buyers. Among them you can highlight Boch, Lynx and others. But the choice is not limited to them. Even in the low price segment you can find good brushes Wiper.
Replacing janitors At Kia Rio 3 (2011-2016) / Replacement Wiper Blade for Kia Rio 3 (2011-2016)
Replacing janitors simple procedure and takes no more than 2- 3 minutes. Simplicity of replacement is due to very comfortable.
KIA SPORTAGE: Factory Brushes Resource (Wipers) Wipers
Good afternoon, today we will consider the question of the wear resistance of factory brushes or wipers janitors.
Follow an important parameter is the size of Kia Sporty janitor. Ignition coil Kia Rio 3 (2012), price. Signs of breakage, check quickly how to remove the coil. What lamp to choose and as a highlighting license plate of your Kia Rio. Remove them. It is different depending on the generation and year of release of the car.
- 20 "(508 mm) for the first generation
- 24 "(610 mm) from the driver, 16" (508 mm) from the passenger side for the second and third generations
- 16 "or 14" Size of the janitor rear glass
Back to the category
Read the same way
Replacing janitors At Kia Sportyj
To replace wipers At Kia Sportage, 1, 2, 3, 4 no tool will be required. Kia Sportage. 2014. Replacing the oil in the MCPP. Kia Sportyj 3 Replacing Oil Replacing Oil in ACPP!. Where is he located. Time to diagnose KIA and search if Kia Sportage 3 is not. The procedure can be performed with your own hands in a few minutes.
Let's start with brushes of windshield janitors. Move the metal brush holder before fixing in this position. Turn the wiper brush by 180 degrees, and then carefully remove it from the "C" - shaped bracket. New janitor put in reverse order. We check that it was reliably fixed in the bracket.
To replace the rear janitor Kia Sportsji need to remove Protective plastic case. In what cases is required replacement of candles? In accordance with technical Regulations, at Kia Rio or Kia Sportage 3 replacement of the SZ should be carried out every 30 thousand km of run. Make it can be carefully lifting it with landing As shown in the photo. After that, you can replace the wiper brush to the new one. After replacing the plastic case put in place.
How to replace the wipers at Kia Rio? Such, not the first glance, a minor item when it comes out of order, immediately becomes necessary. If you want to install new, non-standard wipers Or just replace your old, it will require a little work. In our article you will learn everything you need to know when choosing brushes for Kia Rio.
[Hide]
Sizes of brushes
When choosing a wiper brushes to replace its old, you need to consider several nuances. So, cars Kia. Rio in his already enough long history Several generations of development passed. And for each of them the size of these parts, both for the driver and the passenger, are somewhat different. This nuance must be taken into account when choosing.
Necessary sizes for different options This car model is as follows:
- For the first generation (2000-2005) you will need wiper 53 cm longs for the driver and 45 cm for the passenger.
- For the second generation (2005-2011), the length is 56 cm and 41 cm for the driver's and passenger seat, respectively.
- For the third generation (2011-2016) 66 cm long brushes at the driver and 41 cm for the passenger.
In principle, it is possible to install brushes and other sizes, but you will not receive high-quality cleaning glass in this case. Therefore, it is recommended to choose the models of the above size, based on how your particular car belongs to which generation. It is also necessary to take into account other details, such as windshield.
Types of janitor
There are three main types of wipers suitable for installation on Kia LED, Rio, etc. Each of them has both its own significant advantages and certain cons.
The classic option is frame wipers. IN this case A certain "skeleton" is attached to a brush, which is cleaned with glass. From the main part this device Rockers also move away, a number of 2.3,4 pieces. It is on them that the cleaning tape itself is fixed. Each of such small lateral parts is movable, thereby ensuring quite a good cleaning quality.
A plus of such a device is the ability to replace not all the item, but only the cleaner tape, if the quality of its work does not suit you. This in case of some replacement work provides sufficiently significant cash savings.
The second popular today is a skeleton model. She has no "skeleton". The ribbon includes a special pressed part, most often it is a steel plate. Cheaper models are produced under a specific machine to accurately fit her front glass. Dear options create in such a way that they can be installed on all vehicles, you only need to pay attention to the length parameter.
The disadvantage of the frameless version is that such wipers need to be very careful. Otherwise, you risk the fact that the clamping force will not be enough for effective cleaning, if the brushes are not suitable for the bending of the windshield.
The hybrid elements have a frame, but it is hidden under the shell of rubber, which hides it from ice and other external influences. Pressing the glass in such models is quite good, even at high speeds.
Video below is an overview different species Janitors (author of the video - AutoProfi Team).
As already mentioned above, you need to navigate to which generation your Kia Sportage 3, Rio, etc. belong to. The main parameter that needs to be considered when choosing any type of janitors is the length of this part.
It is not recommended to install models of a smaller length than above. Also, with too long, the wipers simply will not be able to walk through the windshield, as they will interfere with each other. It is best to choose specific models produced by your car. In this case, you are the least risk. Otherwise, you may encounter the fact that your windshield wipers do not cope with the abundance of snow or cleaning on fast speed.
Manufacturers
As for manufacturers, almost all world leaders in this area worked on brushes for machines Kia. Rio.
Among them, such as:
- Bosch;
- DENSO;
- Champion;
- Kamoka;
- Valeo.
Some of these manufacturers produce all types of brushes, other only frameless or hybrid. Below you will find several examples indicating the price of the model.
13.12.2017
To ensure stable visibility in any weather, you need to use good wipers. From this, it would seem, safety on the road depends on a minor element. Therefore, let's look at how to choose and install Kia Rio wipers.
Selection of janitors in size, type and manufacturer
In order to choose the most suitable optionThe following criteria must be taken into account:
- The size;
- Material making basic elements;
- Type of fastening;
- Cost;
- Manufacturer.
The size of Rio janitors differs for different generations Machines, like the size and shape of windshield. For the first generation vehicles (year of release 2000-2005), it is necessary to use brushes with a length of 53 (from the driver) and 45 cm (from the passenger side). On the second generation (2005-2011) - 55 and 40 cm. For Kia Rio 3 (2011-2015) - Driving - 65 cm, passenger - 40 cm. For Rio 4 and cars x-Line series (2015, 2016, 2017) Brushes go 60 and 40 cm.
Varieties of janitor
One of the most important criteria from which you need to repel when choosing is a variety. Different models Janitors have their own design features - they need to be compared with the car brand and operating conditions. Total distinguished 3 main varieties:
Frame. It is a kind of classic cleaner brushes, since it was just such a kind of appeared first. Consist only of 2 elements: fastening (most models are a simple hook) and rubber seal. The advantages of this species should include a relatively low price and high-strength of the frame (largely due to the simplicity of the design). The disadvantages include: too rapid pollution of elements, increased sensitivity to icing (due to the hinge type of compound), low aerodynamic indicators and corrosion. Frame wipers are often found at Kia Rio from the plant.
Frame wipers
Frameless. These wipers appeared in the late 80s and quite quickly won popularity. Such models consist of a rigid base (in most cases it is made of light metal or plastic and covered with rubber to compensate for the friction force), rubber seal and replacement fastening. The advantages of this type include: elevated aerodynamic indicators, stability to icing (due to the absence of ball joints), smooth clamp, which gives uniform cleaning of glass, regardless of its design features and a reduced profile that does not interfere with the review. Among the minuses should be noted: relatively high cost, the inability to replace the cleaning tape (therefore, when it is excessive wear, it is necessary to fully change the design) and the need to pick up brushes under specific brand vehicle. Frameless wipers Kia are usually put on expensive equipment Rio.
Frameless design brushes
Hybrid. As can be seen from the name, it is a combination of the above varieties. Invented such wipers in Japan, and today they are the most practical option. The case in such structures is highlighted by increased strength and, as a result, the last operational period. Also worth noting both high aerodynamic characteristics. Due to the large weight of the design, such wipers cannot be installed on cars, which windshield It has a strong bend. Another drawback is an increased value. However, the price is more affected by the brand.
Hybrid brushes
There are also models of wipers with a specific specification. One of these - winter, which are designed for regions with a harsh climate. Their main feature - they can shoot a small crust of ice from glass. However, they have a significant drawback - very low aerodynamic properties.
In a separate type, it is worth turning on the rear wipers that are intended exclusively for the rear window of the vehicle. Still in stores you can find original wipers for specific models Auto. According to mine constructive features They do not always differ significantly from "ordinary", therefore, most likely, this is a banal trick of autocontracens who want to increase their income by selling consumables.
Review manufacturers
Other no less important factor The choice of wiper brushes Rio is the manufacturer. Among the variety, we note a few most famous and popular:
ANCO CONTOUR. This is a Mexican manufacturer, which is quite exotic for this sphere. On official trials, this kit was estimated 3.8 (maximum score - 5). Among the disadvantages can be noted the lack of instructions in Russian, but if you at least once installed wipers - there will be no problems. The installation procedure is practically independent of the manufacturer. The advantages of this brand include the possibility of installing on the pin lever, which gives it the variability.
Bosch Aerotwin. Buyers noted not quite standard packaging, from which it is quite difficult to deliver wipers - high likely to damage the finger. This brand of janitors received 4.36 points. According to mine performance characteristics It is comparable to the previous option, but a higher estimate was obtained due to the fact that the price is almost 30% lower. Instructions in Russian are also not. It is also worth noting from drawbacks that as a result of the work of brushes on the glass in some places, stripes remain.
Heyner Hybrid. This is one of the most popular brands. hybrid janitans. MAIN TRANSFER - low price. There are 2 adapters for different types Levers. The installation is made without the backlash, while the wipers are fixed quite tight (the only nuance - you have to make a lot of effort). When working, there are very few uncleaned bands. Other Advantage - concise appearanceThanks to which the wipers are not striking. The minuses should include instructions only in German, although it is unlikely someone will be interested in the details that are written on the packaging. On official tests of this brand, 4.5 points were assigned, largely due to low cost.
