Home Heating Connect the STARLINE A9 alarm. Car alarm connection schemes - Starline A9 car alarm installation. Remote shutdown shock sensor

Heating

Connect the STARLINE A9 alarm. Car alarm connection schemes - Starline A9 car alarm installation. Remote shutdown shock sensor

To use remote engine start functions, you must always adhere to the safe operation of the car and this device. The STARLINE A9 key chain is easy to program if you follow the following instructions.

How to remotely disable the shock sensor

ATTENTION! Found a completely simple way to reduce fuel consumption! Do not believe? Auto mechanic with 15 years old also did not believe, until he tried. And now it saves 35,000 rubles per year in gasoline!

This option has several levels. You can use it as many times as you need. It will be considered during one security cycle. To carry out this action, Move the cursor on, and make two clicks with a button located on the key chain. After that, you will see this icon, and hear the sounds - sirens and keyfob melodies. This means that the first level of this sensor has occurred. To turn off the second, do the same actions. If you need to turn on this feature again, then repeat the manipulation, and the image will disappear. One signal will also sound.

How to control the central lock from the keychain when the ignition is enabled

If in this position to sequentially press the button 1, you will see how the locks close and open the locks. On the screen, the StarLine A9 keychain will appear suitable characters and. The ignition sign looks like this.

How to start the engine remotely by keychain

There are two ways, and both of them do not depend on what state is the security mode.

The position of the car will be reflected familiar to display Starline A9. Next will see - the designation of the running engine. When heating is over, the icon will disappear. There may be only four such attempts.

Engine autorun programmed for every day

You can prescribe these parameters to the same thing. necessary time. To implement this, select, and press the button 2. In case of success, you will see the image. Now it will occur every 24 hours. To disable autorun, repeat the manipulation, and this sign will fall.

How to program the autorun of the engine at temperature

These parameters are needed to warm the engine on cold days. Time and temperature are also installed. It can be repeated up to 12 times a day. You need an image. After pressing the button 2 you will see a sign. Disconnection is similar.

Alarm autorun.

For this keychain starline alarm Must have a right time set. You need the designation. After pressing the button 2, you will see. Also disconnect.

Service mode Valet.

It is necessary in order to be able to temporarily disconnect the alarm functions, for example, when you give the car to a hundred. To do this, select a sign. After pressing the 2 button, the flashing designation appears on the screen. Also follows the signals of sirens, keychain and outbreaks of dimensions. Shutdown is similar.

Recording codes Brecks

The maximum number of keyfobs that can be used to record in memory of auto alarms are four. You need to do this when the security is turned off. Plan next.

Turn on the ignition.
Next locate the Valet service button. Now you need to press and hold it until the siren appears. Total 4 signals.
In order to record the main keyfoot with the screen, simultaneously pressing the buttons 1 and 2. Additional key rings without screens are recorded by clamping buttons 3 and 4. This action is made with all additional key rugs. The main thing is to comply with the interval - not more than 5 seconds.
At the end, turn off the ignition. It will be accompanied by outbreaks of dimensions in the amount of 5 pieces.

Important! When you need to record new key rings, overwriting both old, since otherwise they will be removed from the system.

Additional channel №1

This is the opening of the trunk remote method. This channel looks like a yellow-black wire. Activation does not depend on the Starline car alarm system. There are two ways to programming.

Right result - image

Every year, all new alarm models for the car appear on the market, radically different from previous models for internal functionality. The exception did not become the StarLine A9 product, which has new software settings and additional options.

Equipment

The company won confidence due to the fact that it makes the most complete equipment sets and guarantees a light and simple installation. In particular, the Starline A9 alarm package includes:

1 keychain with LCD display;
1 Additional keychain remote control;
processor block;
module with antenna;
various sensors for installation (engine temperature, hood and other);
manual for use and warranty card.

What is noteworthy, additional keychain of remote control car is coming without feedback. Most often, it is resorted to its use in case of loss of the head. It has only 4 buttons that serve to open-closing the doors and start the engine.

According to experts, Starline offers its customers maximum car protection with a set of additional features (timer, alarm clock, autorun, panic modes, etc.) at affordable prices.

Control in three buttons

The control key chain has a display on which you can easily consider all the characters even with bright sunlight or in complete darkness. When you click on a specific button, you can turn on the screen backlight for the convenience of viewing.

An instruction manual for the STARLINE A9 alarm is simple, since programming is only in setting the three buttons located on the upper surface. All of them have a different functional significance both separately and in a certain combination. The first button closer to the antenna allows you to program the following functions:

admission to programming all major commands;
running and stopping the engine (remotely);
staging a car for protection with the engine running.

The second button, located in the middle, allows you to program the current position of the cursor on the key chain and the trunk opening command.
The third button, the most distant from the antenna, has four commands and mainly they have the functions of an additional service. Their description is as follows:

control cursor on key chain;
interrupting sound alert signals;
changing modes in alarm clock and timer, clock setting and power saving mode;
programming a button.

Understand the keychain management is easy, the main thing is initially when you buy the optimal value for the owner and change them only in certain situations. For example, the car warming timer is absolutely not needed for summer time, and in the winter it is a sharp need.

Combinations from buttons

In addition to the fact that each button is programmed separately and sets a specific function, you can configure key fob with key combination. In the STARLINE TWAGE A9 alarm, the instructions for using which comes in the kit gives full programming information, there are many interesting modes.

The combination of buttons 1 and 2 allows you to adjust panic modes, as well as a car search. The essence of the panic mode is controlled by the alarm response.

For example, this mode may be useful in that situation when the owner found suspicious personalities near his car. By pressing the button triggers a sound siren, repeating ill-wishers. This is one of the simplest programmable panic modes, and there are up to three in the STARLINE TWAGE A9 key chain.

The combination of buttons 1 and 3 has a less simple value: it allows you to adjust the keyfilt backlight. The combination of keys 2 and 3 can configure the timer on the communicator if necessary.

Advantages and advantages of the model

Each new model Alarms appearing on the market should be surprised by buyers and have new features, otherwise there will be no interest in purchasing it. Thus, STARLINE A9 alarm has the main advantage - intelligent motor autorun. And also, among the important advantages of this model, the following advantages include:

many sensors (doors, hood, impact and other elements);
communication with the machine within a radius of up to 600 meters due to 128 radio channels;
the ability to start the engine from mobile phone (With the appropriate setting of specialists).

Starline A9 carnage is inserted by AAA type battery. The validity period directly depends on the frequency of use and many other factors, but on average - from 3 to 6 months.
The equipment has a dynamic control code, that is, protection against selection and interception. Thanks to such safety parameters vehicle It turns out a completely new level.

First of all, you need to get acquainted with the TWAGE A9 delivery package. This includes the following elements.

Managing processor, central. It is placed in plastic housing.
Device for transmission and receptions of the signal. It has a sensor for measuring temperature in the cabin of the machine, as well as equipped with a built-in antenna.
The basic control key chain is needed for bilateral communication. It has a display, a technically complicated device.
Auxiliary key chain. It is not so functional, provides one-sided connection. His radius is significantly less.
Stop application will determine the sensor having two levels of sensitivity.
The temperature in the engine compartment is also fixed by an additional sensor.
Assembly with wiring there is a setup key.
You can view the overall state of the system by visually thanks to the indicator.
Completed in the kit and wiring harnesses.
There is a terminal switch on the hood of the machine.
If the car's hijacking attempt is made, you can activate the anti-label option using a special button.

Be sure to comes with a complete package of technical documentation.

Specifications

Denote key specifications:

The basic control panel has a maximum range of 600 meters.
The operating frequency of the chains is 434 MHz.
The main unit functions at temperatures from -40 to +85 ° C.
An additional keychain works normally within a radius of 15 meters.
The pager in the base unit can receive a signal at a distance of 1,200 meters.
In the range of 9 - 18 V is supply voltage.

It is important to understand that the radius of the pager action, the remotes can decline. Here, a number of negative factors have its influence: these are interference and density of development, weather conditions and an antenna mounting zone in the car, the battery charge and the relative position of the transmitter with the receiver.

Main features

When the STARLINE STARLIZATION is operated with autorun, the instruction is necessary for correct operation with the system. Car alarms provide protection of the car from theft, and also allows you to control multiple areas at the same time. Station and additional terminats guarantee the safety of the opened body elements. Motor is protected from launch due to the modern electronic block. Lever arm manual brakes Also protected from shutdown.

The system has several levels of protection.

The code signal used in the control circuit is dynamic. The code is changing constantly, so it is impossible to pick up, there is reliable protection from the interception.
You can turn off siren, and leave the security.
If the power source is turned off, the system itself will remember the state.

There is a wide additional feature, described in detail in the instructions.

Additional functions

You can also use, program additional features. Motorists use:

clock setting
remote running motor
alarm clock.

The most popular is the function of the remote starting of the motor.

Description of the alarm key chain

Full key rings are needed to control the system, programming and control. Mostly keychain provides a vibration, beep. They apply when informing and configuring.

Key chains have replaceable batteries. In an additional, this is a lithium element, and mostly - the usual battery of the AAA type.

The instructions are especially noted that water should not fall into the device. If the keychain is still a wink, it needs to be disassembled, dried.

On the main key chain, you can use three buttons. We numbered them in order. Used as short-term pressing, less seconds and long-term - 3 and 6 seconds.

Buttons Base Charehouse

Consider the functions of the buttons on the basic keychain. For example, many are interested in how to turn on the STARLINE autorun. Find out.

First button:

the system is turned on short press;
in case of an initiated engine, protection is turned on by a long pressing;
the engine can be turned off or on in automatic start mode, using a long press;
if you press for a long time, sequentially with button 2, it turns on panic mode;
short pressing, in turn with a short press button 2, starts searching for the machine.

The second button is needed to open the castle on the trunk (long press). She also confirms the command that was chosen by the cursor. Here you need a short press.

Button 3 also has many features:

short press moving on the display the cursor;
you can turn off the alarm signal message by short press;
the function of the button 1 is also specified, with a long press;
it is possible to configure different keyfire functions to a long press, and it is necessary to monitor the display;
the timer is installed, while pressing the short one, in turns with a short pressing button 2;
the button also adjusts the alert system (pressing serials with button 1, short).

Buttons of additional blocks

There is also an additional keychain. It is equipped with four buttons with a fairly wide functionality. Apply short and long press.

The first button of the additional keyfob is used in the following cases:

control of an additional third channel (long press);
shutdown, or the inclusion of the protection mode (short);
managing the work of the sensor fixing the blow (pressing short, together with a short press button 3);
you can activate panic mode (briefly, along with button 2);
it also turns on the service mode (click briefly, simultaneously with the button 4).

With button 2, such actions are performed on the additional keychain:

can be long pressing to increase the engine time;
short press turn off and turn on the engine;
the daily automatic start mode is activated, with a brief press along with the 4 button;
you can turn on the temperature autorun (short press, sequential with button 3);
the security system is also included when the engine is running (pressing long).

The fourth and third buttons are also effective:

the trunk lock opens the button 3, with a long press;
the car can be found in the parking lot, if you briefly press the 3 button;
anti-Frame mode is activated while simultaneously pressing the 4 and 3 buttons;
you can record the parameters during the programming process, if you press the 4 and 3 button to be pressed for a long time;
also silently turns off and the system is turned on, with a short press button 4.

The options are quite a lot, while the system is easily programmed using both keyfobs.

Installing STARLINE A9

Now the high-quality installation of car alarm Starline is guaranteed from official dealers. There will definitely make everything competently, perform all the necessary settings, and if necessary, there will be exhaustive consultations, they will answer questions about the operation of the system.

Of course, you can set the alarm and in the service. But there often arise questions. Then car enthusiasts have to return, ask to finish work. There is another option - independently set the alarm on personal car. It is not so difficult if there is instructions for steps, as well as special installation cards Starline.

Independent installation: Step by step instructions

Consider in more detail the alarm installation algorithm.

First of all, the basic module is set. His place is on the instrument panel, in the recess. It is important to make sure that there are no water leaks. The block is important to fasten with plastic screeds or self-drawing, so that it does not shift due to vibration.
Sensor motor compartment Mounted on the box or attached to the engine.
Antenna with a temperature sensor, with a block, fixed on lobby glass. At the same time, the minimum distance from the body panel should be 50 mm.
The shock sensor is tightly fasten in the cabin. It should be in the access area for configuration.
Under the hood put Sirena. It must be fenced from overheating, from wetting. Sirena is acquired separately. The model S.20.3 is suitable.
It is necessary to take care of the reliable contact of additional terminivities to avoid false alarm response.
The diode is installed on the instrument panel, in sight.
Additional button to activate the system when trying to robbery, hijacking, as well as the VALET button is hidden, but in the access area for the owner.
Interference can create a ignition system. Therefore, all the wires should be packed from it.

Any wiring twists are definitely isolated.

Alarm operation Starline A9

For maximum convenience, when operating the system, it is advisable to always have both key chains with you. They should not be exposed to moisture, do not blame them, hit. It is also important to change the elements in time, because when the charge is reduced, the key rings begin to work worse, they have less radius.

Programming functions

When the system is already connected to on-board network Car, it is important to do the settings. Remember a step-by-step algorithm:

First of all, the ignition is activated. You need to press the VALET key six times in a row.
Then the ignition turns off. Six beeps of sirens will sound, a diode will break six times dashboard. This means that the system is ready for programming.
Each function is chosen by the Valet key. The number of clicks is the function number. Each press will be confirmed by a diode and siren.
In 10 seconds you need to press keys 1 or 2 on the key chain.
When one function is recorded, you can go to the next option by pressing the service key.
If all options are recorded, you need to leave the setup mode. You can wait. After a few seconds of downtime, the system itself will finish programming. Five emergency alarm migra - exit confirmation.

When something goes wrong, you can reset the settings. Just press VALET 10 times.

Key chare key combinations

We have already considered most of the key combination, studying the features of the chains. But there are some combinations that are particularly often used. Let us dwell on them.

Greetings, dear readers of the site!
I want to tell you a story about replacing the block for the Starline car alarm.
If briefly, it works, it works, I recommend!

From recently, I started to join me on the main key chain of the alarm, it was sold and triggered one time. It was decided to disassemble and see what happened there.
The autopsy showed that due to the design curve of the buttons and the frequent use of the same button, the legs could not withstand the tension and decided to break away from the board.
The button first soldered at home, was enough for a week. Next was soldered on a soldering station with a special, more solid tin, also had a short time, fell off three weeks later.

so it turned out in the end

This button is just tied to the power on / off, so very necessary. Of course, there is a second, programmable button, with which you can also put on guard, but it is inconvenient.
Therefore, it was decided to purchase the second key chain.
I have a fairly old alarm and the original keyfobs are practically not found, and what can be found is not a fact that it turns out to be the original. + Translate price tag.
The fluid search has shown that there are key rings on Ali, but under different veiled names, it very complicated the search. For example, this seller called her Tamarack, the other was Twace, everything is looking for on the word Starline - with a horse price tag.

Also upset the fact that the keyfobs specifically for StarLine A8 are not only for A9. The officially STARLINE state reports that the key rings are not compatible, but at the same time on the profile forum the people wrote that partially compatible and there may be problems with the key fob in the signaling of the signaling, as well as some functions may not work.
A deeper google led to the conclusion that all the same key chains are compatible and basic functions work.

For A9, the choice is much more diverse (against zero for A8). I came across this lot, the price tag was one of the lowest. Of course, it was embarrassed by a small rating of the seller and a modest assortment in the store, but I took the final decision after reading one of the comments that one buyer was successfully stitched by A8. Mostly all the other reviews are good, it was decided to buy.

I ordered, paid, everything is OK. I sent the seller about the 3rd or 4th day, I don't remember exactly already.
Track with tracking. Delivery on current standards is not fast - exactly a month.

Packaging on a troeuchka, a yellow package, the key chain itself in the puppete package, unreliable however. On the way, all the puppies were pleased with mail employees, while they were thrown by my parcel. Therefore, it was worth packing better, they could have broken the screen.

The seller even put this postcard, signed himself. Again, 5 stars asks.

At the sight of a large similarity with the original, although I also can't know if I have the original, because I received a signal from the car and I don't know anything about her biography.
Differences can be reduced that after all, my key chain from A8, and this one from A9.
The case is absolutely the same, quite a bit deeper than the hole under the button and the buttons themselves are made from another material, slightly larger out of the housing.
Pictograms on the screen are a bit brighter from the new, perhaps on the old one they focused on time.
Illumination of the same color. The resulting keyfob seems a little worse the screen in quality, if you look at the top, then the badges are flexible, the old one was also, but not so much expressed.
In general, more visual differences did not find.

External comparison

Even there is a holographic sticker StarLine :)

I stitched the key chain with a bang, works as a native. Programmatically distinguished by the A9 key chain from A8 consists only that the cursor of the programmable button 2 over time hesitates to the default position, there was no such thing on the old old one.

I stitched on this instruction:
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
1. Turn the ignition.
2. Press and hold the VALET service button until 4 siren signals appear.
3. To write the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
4. Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
5. Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.

When I stitched new keychain, missed very much important moment, the button then on the old one is broken and it will not work it. Thus, if something went wrong, I would stay without a signal for a while, but everything went like on the oil, the new key chain was lying without any problems. Now it remains to fall the old old and flash it, it will be a spare.

Checked the main functions, accurately work:
- Removal / arming, with sound and without.
- alarm on the shock sensor 1 and 2 levels with feedback
- autorun and engine stop.
- Request information about the status of the car (temperature, whether the engine is launched, do the doors, the position of the handbrake, ignition)
- Opening the trunk on the second channel.
In the rest of the functions I do not need, so I did not check.

To whom it is interesting, for comparison, photos of the insides, on top of the old keychain, under it overlooked sabzh.

It can be seen in the naked eye that in the version A8 screen on the loop, in A9 Wpayan on the legs

Separate fees did not, reluctant to gut a new key chain, but visually there are differences in circuitry

And again these buttons that, I hope this time stretches for a long time. (Photo after the 3rd propios of the old key fob)

By the time the review is published, the old keychain was released, the button started again. Both key products have been successfully recorded in the signal of the signal. Unfortunately, they do not work in a pair, that is, when the alarm is triggered, the key chain, from which they put on guard, will be silent. The status of protection does not change dynamically on both keyboards, only on the one from which you install / remove the security.
In general, they work according to the principle - who is the last, that and dad.

The goods are purchased for money and on its own initiative. If someone decides to buy a key chain from this seller, write in the comments, I will try to negotiate a discount for Muskovchan.

For Sim I speak, thanks for watching!

I plan to buy +16. Add to favourites I liked the review +24 +52

System Starline Twace It can be installed on cars with a voltage of battery 12V and a negative pole on the housing.

The central block is placed in the cabin in a hidden place, preferably under the dashboard - in this case the length of the connecting wires will be minimal. To prevent entering the moisture block, it is recommended to establish it in such a way as to eliminate the flow of water droplets on the wires inside the housing. Secure the block on a flat surface with screw screws or bilateral tape so as to exclude its movement during vibrations.

The transceiver module with an antenna fasten on the windshield of the car so that from the antenna to the metal parts of the body it was at least 5 cm. In this case, the maximum range of keychains is ensured. Also, when installing, it should be noted that the temperature meter of the cabin is in this module, so the module should be placed as far as possible from heat sources and avoid the sun rays on it. Otherwise, temperature testimony may differ from the real temperature of the cabin.

Remove the engine temperature sensor to secure on the engine housing under one of the M6 \u200b\u200bbolts available on the engine, ensuring good contact with the engine housing. The position of the sensor will determine the correctness of the temperature determination of the engine.

The impact sensor is rigidly fasten in the car, ensuring access to its adjustments.

LED indicator fasten the domestic location on the dashboard.

The Valet service button and the activation mode button set to the hidden, but available to the user.

When installing push-button switches under the hood and in the trunk, check the correctness of their operation. With a closed hood or trunk, the gap between the contacts in the switch should be at least 3 mm. Incorrect installation of push-button switches is often the cause of false alarms.

Conducting the wires as far as possible from the sources of electrical interference of the ignition, high-voltage wires, etc. Note that the wires do not come into contact with the moving parts of the design of the car - pedals, steering traction, etc.

Installation of electrical wiring connections must be made when the car battery is disconnected.

Attention! If the car is equipped with an air cushion or has a coded receiver, when the power is turned off, follow the instruction manual for the car or receiver.

All of all-point connections are performed using soldering and isolate well.

Connect the central unit and other signaling components to connect to cable connectors only after the installation is completed. Installation of alarm Machine in accordance with the connection scheme.

Connecting transceiver

The antenna transceiver module is connected to a five-pin connector located in the central unit under the folding lid, with a cable that is included in the alarm kit.

Connecting a two-level shock sensor

The shock sensor is connected to the central unit using a four-wire cable included in the alarm kit. Power supply (body potential) on the sensor is carried out only in the mode of protection. Sensor sensitivity in levels is regulated by potentiometers on the sensor housing.

Connecting a LED indicator

Connect the LED plug into the two-contact connector, located in the central block under the folding lid.

Connecting the engine temperature sensor

The engine temperature sensor connects to the central unit using a 2-wire cable. One of the cable wires, connect to an orange-gray wire (input of the hood key switch) of the 18-pin connector of the central unit, and connect the second wire to the car housing. Connection polarity is not important. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.

Connecting the 6-pin power connector of the central unit

Red wire (№4) - plus power + 12V, connect to a positive battery terminal.

Blue Wire (# 2) - Output Control Management, Connect the ignition Castle ACC terminal.

Yellow wire (№5) - Exit ignition support # 1, connect to terminal 15 ignition lock.

Green wire (№6) - Exit ignition support # 2. The output algorithm is programmed (Function 7). See "Temporary system work charts when remotely start the engine."

Black and white wire (№3) - the output control of the starter, plug the ignition lock terminal 50/1.

Black and yellow wire (№1) - the output of the starter lock control. Connect after the ignition lock from the starter side, having previously cutting the standard wire that runs from the ignition lock to the starter.

Connecting the 18-pin Central Block Connector

Red wire (№1) - plus power + 12V, connect to a positive battery terminal.

Black wire (№9) - minus power, connect with a car housing, ensuring good contact.

Green-black wire (№10) - Connect to lamps overall lights or rotation pointers. Maximum exit load current 7,5A.

Green-yellow wire (№11) - connect to lamps of overall lights or turning pointers. Maximum exit load current 7,5A.

Gray wire (№13) is a positive output for connecting to siren. Maximum output current 2a.

Blue-black wire (№17) - Connect the doors closed on the housing to the button switches when opening the doors.

Blue-red wire (№7) - plug the doors to a + 12V button switches when opening the doors.

Orange-gray wire (№18) - Connect the hood closer to the hood when opening the hood. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.

Orange-white wire (№8) - Connect the trunk to the housing to the push-button switches when opening the trunk.

Yellow-black wire (№15) - negative yield of an additional channel number 1. The duration of the 1 second control signal. Maximum load current 300mA. The channel can be used to control the solenoid spilling trunk. The connection requires an additional relay. An example of a connection scheme is shown in the figure.

The yellow-red wire (No. 5) is a negative yield of an additional channel number 2. Maximum load current 300mA. The duration of the output signal pulse is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). Channel can be used to control additional equipment car. The connection requires an additional relay.

Yellow-blue wire (№14) - negative yield of an additional channel number 3. Maximum load current 300mA. The duration of the output signal pulse is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). The channel can be programmed to implement the function of two-step unlocking door locks or to control other car devices. The connection requires an additional relay.

Blue wire (№2) - negative yield of an additional channel number 4. Maximum load current 300mA. The channel can be programmed to connect to salon lighting or windows control module. The connection requires an additional relay.

Black and yellow wire (№4) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the protection mode is turned on, the operation of the turbotimer, the activation of the function of anti-grab, activation of the immobilizer. At remote i. automatic launch In the security mode, the output is not turned off. It is recommended to use to lock the starter circuit. When connected, an additional relay is required.

Black and white wire (No. 12) - negative output of the status of alarm. Maximum load current 300mA. It can be used to block the engine with normally open (HP) or normal-closed (NZ) work algorithm. The connection requires an additional relay.

Black and Red Wire (No. 3) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the turbotimer and the engine starts. In start mode, it can be used to restore the locked engine circuits.

Orange-violet wire (№16) - negative status control input parking brake Or foot brake pedals. The lack of negative potential on this wire in the security mode will trigger alarm operation, and in the mode of running remotely or automatically engine - the engine stop. An example of a connection scheme is shown in the figure.

Serious-black wire (№6) - input control of the engine operation. Input resistance of at least 100 com. Input sensitivity - 1.0V.

Choosing a way of controlling the engine operation (Connecting a gray-black wire
STARLINE A9 alarm)

Motor Control by Tank

The gray-black wire is connected to the delta. The engine start diagnostics is carried out by changing the frequency of the tip signal. On the correctness of the connection of the black and gray wire, it is possible to judge the duration of the starter after turning off the starter during the engine start and receiving the start confirmation on the alarm key chain.

For proper connection A black and gray wire starter must turn off simultaneously with the start of the engine, regardless of the programmed starter scroll duration.

Motor control over the generator

The gray-black wire is connected to the generator output, which is connected to the lamp on the dashboard. Successful engine launch will be monitored by the presence of a positive voltage + 12V at the output of the generator with the engine running. When the black and gray wire is properly connected, the starter must turn off simultaneously with the start of the engine, regardless of the programmed duration of the starter scroll.

Attention! When a gray-black wire is connected to the generator output, it is used to use the quenching resistor 510 com ... 680 com.

Control of the engine voltage onboard network

In case of the difficulty of detecting the chains of the band or generator, it is allowed to use the engine start monitoring mode over the on-board network. In this case, the gray-black wire does not connect and it is necessary to isolate it. Start confirmation will occur automatically after starting the engine. The disadvantage of this method of control is the fixed starter time. For proper operation of the starter without a twist, you will need to select the necessary duration, programming the function number 3 to the values \u200b\u200bof 800, 1200, 1800 or 3000 ms.

Connecting the built-in engine lock circuit

Run the chain between the ignition lock and starter. In the chain break, connect the black and white wire of the 6-pin connector from the ignition lock and the black and yellow wire 6-pin connector from the starter side. The maximum current of the built-in lock relay is 40a.

Connecting an external engine lock circuit using conventional relays

Run one of the standard engine start circuits and connect the additional relay into the circuit break. The type of contacts of the NR lock relay (normally open) or NZ (normally closed) is programmed (function 15). Initially, the factory is programmed by the NZ Type of Relay Contacts. An example of a connection scheme of one of the chains is shown in the figure.

Connecting an external engine blocking circuit using a Universal Starline Wireless Lock Set

This method of blocking the engine significantly increases anti-theft alarm properties. To control the module included in the Universal Starline Wireless Lock Kit, use a black and white alarm wire, pre-programmed it on a normally open (HP) type of contacts. Possible engine blocking schemes are given in the installation instructions for installing the Universal Wireless Lock Starline.

Connection to Solenoid Unlocking Trudge

Alarm has an outlet for remote spilling trunk (yellow-black wire). Maximum load Exit - 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.

Connect to salon lighting

An additional alarm channel 2 can be used to connect to the neighbor headlights and the implementation of the "Lightway" function (yellow-red wire). The maximum output load is 300 mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.

Connecting an orange-purple wire on cars with manual and automatic gearbox

On vehicles with manual gearbox, connect this wire to the parking brake button switch, which closes to the housing when the brake is turned on.

On vehicles with automatic gearbox, connect this wire to the brake pedal button closed to + 12V when the brake pedal is pressed.

The alarm has an output that can be used to connect to salon lighting and implementing the function of the "polite illumination of the cabin" (blue wire). The maximum output load is 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.

Connecting to neighbor headlights

Connect to the central locking system

Starline Twage alarm has built-in central lock control relays. Relay contacts are displayed on a 6-pin connector. Load capacity of built-in relay 15a. The duration of control pulses is programmed (Function 9).