Alarm "Starline A9" is very popular with drivers different cars. The system package includes detailed instructions. It allows you to connect and configure alarm. The manual also spelled out the principles of system operation. After studying user feedback and the provisions of the instruction, you can highlight the basic principles of working with Starline A9. Programming a keychain will be a simple task. Tips of experienced motorists will allow you to configure quickly. It will give the opportunity to enjoy all options. The alarm can be configured to work in or without autorun mode. The blocking function is also adjusted.
General
"Starline A9", the instruction manual of which requires studying before starting to install the system and programming a key fob, is alarm with remote engine start. It has a double-sided radio channel. Its range on the area without obstacles is 600 m. In the pager mode, this indicator increases by 2 times.
Radio signal coding is dynamic. The choice is carried out on the cursor principle. Each command is controlled by its button. It is displayed on the key fob. The system provides sound and vibrating signals alert.
In addition to the main data on the condition of the car, the keychain shows the user time, the temperature in the cabin, as well as alarm clock.
You can install the presented system on machines with diesel, gasoline or turbocharged engine type. The gearbox can be automatic or manual.
Safety regulations
Using the functions of the remote or automatic engine start, the control of the machine nodes, it is necessary to follow the safety measures to use the Starline A9 system. The instruction manual clearly indicates.
The car is important to park on a well-viewed area. In this case, it must be installed on the parking brake. Lever arm automatic transmission Must be in the PARK position, and the handmade gearbox is in neutral.
You can not run the engine in the absence of a driver in the cabin, if someone is located in front of or car. The keychain is unacceptable to give to children or persons who can not manage this device. The machine must be in good condition, in its system there must be a sufficient amount of all supplies and fuel.
Keychain management
The laid signaling functions are performed automatically or by key fob signals. Some of them can be changed. The procedure is spelled out in the instructions for the Starline A9 system. Programming the keychain is simply carried out. For this, the device has three buttons. Information is displayed on a liquid crystal display.
Driving a car can be performed by one or more keyfobs. If the main device is lost, you can use the spare console. This is a key chain with buttons that has no information for providing information to the user. With it, you can manage almost all system functions.
If the owners of the car use several keyfobs with the display, then all information about the status of car systems and alarm will be displayed on the device screen from which the command was served.
Purpose buttons
Setting the "Starline A9" keychain with a liquid crystal display is performed using the three buttons on the housing. Their combinations make it possible to manage system functions.
Button I may include the programming command if it is quickly pressing once. Holding her 3 seconds, the driver remotely starts or stops the engine. The user can enable security mode. To do this, with the engine running, this button also holds 3 seconds.
Button II with a short press sets the position of the cursor on the screen. If you hold it 3 seconds, the trunk will open.
Button III also allows you to manage the cursor position when you click. It interrupts key fob alert signals. To do this, it is kept pressed 0.5 seconds. To enable or disable clock setting mode, alarm clock, energy saving, this button hold 3 seconds. If you hold it squeezed for 6 seconds, you can enter the i button programming mode.
Pictures on display
All information about the state of the car and the signaling itself can be viewed on the Starline A9 system display. Icons on the key chain will help to navigate in setup and control modes. The instructions are clearly spelled out which picture corresponds to a function or another.
The indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general view of the device functions. To fully understand the appointment of each of them, you need to carefully examine the instructions.
The first picture that is located on the left corresponds to the anti-label mode. If it is on the display, this command is turned on. Next, the function of the additional channel 3. Moved to the right side, you can see the motor autorun mode in terms of temperature. Next is the function of daily autorun or turn on the an alarm engine. This picture follows the remote switching on or off of the motor.
After that, the modes of silent protection are followed. In this case, confirmation does not work. The following picture corresponds to the protection function with the beep. It goes off at a distance of the shock sensor.
A little more about the picture of the Valet service mode is. It should be displayed a picture of the state of car systems and salon temperature indicators. Next, there is an additional channel 2. Ends the chain of the pictures remote opening of the trunk.
Button I.
The i button on the main keychain is programmed by the user. This can be made an unlimited number of times. Most often it is used to shut down or switch on the security mode in the Starline A9 system. Programming a new keychain is simply performed.
Use the III button to move the cursor over the screen. When the desired mode is selected, for example, the inclusion of the protection function or any other, the movement is stopped. The III button is held for 6 seconds. First, two beeps will sound. Then more 3. Then then button are pressed to activate the selected function.
After such a programming, with a short press of the button I, the previously selected mode will be turned on. To set a new feature for it, again perform the above operation.
Button II.
You can assign a function for a button II. You need to press quickly button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue to move, it will move counterclockwise.
The pictures listed above will be selected one after another. When the cursor comes to the desired program, the movement of the III button is stopped. To execute the selected program, the user presses the ii button.
After 10 seconds after pressing any button, the cursor will return to the original CHECK state. This command controls the condition of the machine and temperature in its cabin. It does not change the status of alarm. Knowing this, the user will not have a question how to see the temperature on the Starline A9 key chain. When operating, it is this team that is the most sought-after.
Installation of watch
Starting to work with the system, you need to know how to set up time on the "Starline A9" key chain. You need to hold the III button until two beeps appear. The clock on the display will flash.
To enlarge the digital value of the clock, minutes, you need to press the i button, and to reduce the II button. The transition from the clock to minutes is carried out by a short press of the III button.
Upon completion of the settings, you need to exit the clock setting mode. To do this, hold the III clad button before the appearance of one beep. According to the manufacturer's instructions, you can set the alarm or timer readings.
Code recording
The driver can independently enter into memory system "Starline A9". Programming the keychain is performed in the protection mode. You can bind up to 4 remotes. This must be done if the alarm for some reason does not see the key fob signal or the machine with the already installed system.
To log in to the programming mode, you must enable ignition. The Valet service button is held before the appearance of four beeps.
First set up the main key chain. It clauses the I and II buttons. For additional remote controls, buttons III and IV are pressed without display. After successfully recording the first keyfob, one siren signal will sound.
For all keyfobs, the same procedure is performed. The interval between the record should not be more than 5 seconds. Otherwise, the programming mode will be completed automatically. Next you need to turn off the ignition. The success of the operation will be confirmed 5 outbreaks overall lights cars.
Engine starting
Many drivers are interested in how to make the car with a keychain. "Starline A9" when connecting alarm involves programming the type of gearbox. If it is manual, when installing a wire loop is cut (as indicated in the instruction). If on the car it costs automatic boxThis element is saved.
The engine type is also set. There are two features of the remote launch of the motor. In the first case, you need to put the cursor on the corresponding icon on the display screen. Then you need to press the II button. Or simply clamping button i for 3 seconds.
With the first attempt to start 3 beeps of sirens, 3 outbreaks of overall lights. The keychain will publish a melodic signal. The icon on the display will burn constantly. You can set the engine warming time.
Reset installations
Sometimes the driver may need information how to reset the Starline A9 keyword settings. Actions are manufactured in a specific sequence. Ignition first turns on. Next, the Valet service button is pressed 10 times. After that, the user turns off the ignition. The entrance to the discharge mode is made if 10 beeps of sirens sound after these manipulations.
The service button must be pressed another 1 time. After that, another siren signal will sound. The driver presses the i button on the main key chain. A short signal will sound. This means that the reset was produced. From the settings mode, the system will automatically come out in 5 seconds. flare out 5 times. The keychain will publish a melodic signal.
Having considered the features of the automotive alarm "Starline A9", programming the keyboard you do easily and simply. Before working with equipment, you must read the manufacturer's instructions. This will allow the enjoyed functions fully. If necessary, you can return the system to the factory settings. Control keychain will allow you to use security system The car is comfortable and fully.
The basic instruction attached to the STARLINE A9 signal contains all information about its connection and operation. How to conduct a setting, the instructions also said. The tips that are formed on the basis of feedback will be listed here. It will also be indicated how to quickly configure the main keychain to start using any of the options. You can connect an alarm with auto-start or without, as well as apply either not to use blocking. In all cases there will be several options. By the way, here we are talking about one model - Starline Twage A9, and not a9 dialog.
How to implement autorun
Let's see what is provided in the basic instruction attached to the Starline A9 signal.
Scroll of power connector
The six wires indicated above are connected to the ignition lock terminals. For example, the "red" cord is connected to the 30th terminal, on which the "+12" voltage remains all the time. And the 15th terminal receiving the potential when turning the key must be connected to the "yellow" wire. Last requirement is always observed, even if you perform installation without autorun.
Wiring power connector
Immediately list, what all cables are connected:
- Red - lock terminal 30;
- Yellow - Terminal 15 (ignition);
- Blue - lock terminal, voltage on which is missing during the starter operation, but appears when the key turns to the ACC label;
- Green - can duplicate the yellow or blue wire, and the first option is chosen by default;
- Black and white - included in the gap of the starter cable, connecting the cord of the signaling with the terminal 50;
- Black and yellow - starter nutrition.
"Blue cord" is usually connected to the "15/2" terminal to feed the second ignition line. If it is missing, you can serve a current into the accessory chain. It all depends on the standard scheme - the auto alarm is compatible with any of them.
When the start of the autorun is performed, the signaling emulates the behavior of the standard lock. But some lines, such as the power of accessories, is not necessarily connected. But the starter must receive the power in any case:
Sparking lock terminals
If it is known that the autorun does not use the owner, connect only one wire - "yellow". We need a turbo-timer - add a "red" cord here. In the second case, all compounds must withstand a significant current (up to 30 A). In the first version, this requirement is missing.
Installation of signal chains
If everything is done, as indicated above, you can not start the motor motor. The car alarm must "know", whether the car is in the parking lot, and it is also desirable that the engine operation is controlled. By connecting only the brake ender, you can observe the following: the sound of the starter operation appears, and then the motor will start and stalls. The fact is that you still need to install a commander. Three wires that are listed here are mainly connector:
- Black and red (3) - managing a cross;
- Orange-violet (16) - monitoring the state of the brake pedal or the "handler";
- SERO-Black (6) - Engine Control Input: The cord is connected to a delivery or to the terminal on which the potential "+" appears when starting.
Note that the third cord can not be connected to anything, and then it is not even necessary to perform programming.
In the last option, the car alarm "monitors" for the voltage of the network, controlling the operation of the motor on it. But the instructions say that such a method is the most unreliable. It is better not to use control during operation at all, assigning the option 6 value 3.
Unlike most car alarms, the STARLINE TWAGE A9 system recognizes only the presence of the "mass" potential, if we talk about the brake control input. So, in the basic scheme is better to add a diode:
Connecting control wires
The resistor extends the excess voltage, and the condenser makes the signal symmetrical. In standard instructions, these details are not considered.
Connect the cord in the gray-black shell or to the generator terminal, or to the delta. By default, the second option is specified in the settings - "Danger".
Of course, the STARLINE A9 system can control the bypass. The coating relay winding is connected as follows:
- Black and Red Cord - Minus Power Supplies;
- Terminal 15 - "Plus" supply voltage.
This option, as the only correct, is specified in the basic instruction. Suppose the motor will start "once" or stall immediately after launch. Try then to connect the winding not to the 15th terminal, but by the 30th. The essence of the last sentence is clear: Alarm can enable ignition later than you need. Immobilizer will then not perceive the presence of a key.
Trial launch
If the signaling is installed, the engine test starts. Make sure that:
- PPC selection loop is cut if the system was installed on a car with MCP;
- Connecting the brake sensor for machines with MCP produced according to the circuit - the wire is connected to the "handler" button;
- Even for machines with "mechanics", preparation is carried out, then performed during operation.
The test looks simple: taking the main key chain, press the key 1. Pressing duration - 3 seconds.
Display of the main console
The sound of the working starter will appear, but the main thing is not in this! The keychain should display the smoke icon.
Turn off or turn on the motor can be single and the same key. Note that after stopping the engine, the icon should disappear. If the condition is not fulfilled, it is impossible to use autorun. By the way, the system can not work correctly if "training" was not conducted. What is true for one option - control by the dress.
Consider how the preparation procedure looks like:
- Involve "handbrake" without turning off the ignition;
- The key is made (the engine is working);
- In 30 seconds leave the salon and closed the doors;
- The motor will stall when half a minute after step 2.
Let one of the conditions: the sound of the working motor changes either the engine stalls until step 3. It is possible to correct the situation: when programming the function 15 is assigned to 2 or 4. Then between the steps 1-2 another action will be added between the steps 1-2. Taking a key chain, you will need to press button 1, without releasing it to a melodic signal.
Setting butter keys
Note that any of the additional keychains in this case Not suitable.
Each key chain, on which there is no display, is equipped with one key that allows you to perform remote launch. The button is indicated by number 2, and you need to press it half a second.
Connecting the temperature sensor - error
If we talk about the STARLINE A9 alarm, it leads to the temperature control:
- If an external sensor is connected, the engine temperature is controlled, and the keychain displays the temperature of the cabin;
- Do not connect the sensor, know that the car alarm is measured in the temperature inside its housing.
It seems the option using an external sensor is the most suitable. Connection, in turn, spend in parallel with microcopki contacts:
Basic Sensor Installation Scheme
The button closes when opening the hood.
The above is true for STARLINE TWAGE A9, and in general for any car alarms installed additionally. Sensor itself, that is, the resistor is connected to a standard microcopder. But when operating an effect arises:
- When the hood is open, contacts are closed - everything is right here;
- Closing the hood, you can get a "plus" potential on the signal output, which is invalid.
The latter is due to the fact that in the standard microcopka scheme is connected to the lamp, which, in turn, always gets nutrition. Lamp thread has low resistance, and "12 volts" remains at the input of the signal. Well, or "almost 12".
The problem considered above has two solutions. If during operation, the light under the hood is not used, the cord is cut, which goes to the lamp:
Improved connection scheme
But interference with the standard wiring is incorrect. It is better to install an additional microcal. In addition, in the StarLine A9 sets, it is always present.
Obviously, do something in accordance with the instructions. But at the same time, the features characteristic of each car are also taken into account. This rule uses, by mounting any alarm. We wish you success.
Adding blocks
Again, we present the basic scheme taken from the instructions:
Installing a blocking relay
Here, as you can see, one pair of contacts is used - normally closed (NZ). Interestingly, another option (HP) will be set in the processor memory. When setting, assign functions 15 The value 3. and the diagram will start working.
The starter chain rupture, as indicated in the first chapter, includes two wires from the power connector. Thus, another blocking is implemented: the alarm is not closed by contacts when the protection is involved. Bad is that blocking the starter is almost useless. Motor with hijacking "from handles".
Each car alarm can monitor and normally open contacts. But the STARLINE TWAGE A9 system, as well as other StarLine signaling to such a relay, is better not to connect. Simply, it is not always possible to start the engine. We are talking about starting "from the key."
What and how to program
For the system under consideration here, a simple settings table is suitable:
Software changed parameters
The number of options characteristic of the Starline TWAGE A9 model is 16. Seven of them, as we see, are connected by autorun. To configure, you will need any of the keychains. Values \u200b\u200b3 and 4 are specified like this: the key 1 or 2 is humbered and held three seconds. This is true if the main keychain is used.
An additional alarm console is equipped with four separate keys. Of course, they correspond to the values \u200b\u200bfrom "1" to "4". Know about it.
Here is a comment on paragraph 15. Suppose three conditions:
- The signaling was installed on a car with MCP;
- Everything is connected according to the instructions;
- When removing the key from the lock, the sound motor sound changes.
If all statements are correct, use the SAFE setting. In any other case, leave an AUTO version. As you can see, everything is simple.
The above council is important in two cases: if autorun is implemented or if a turbo-timer is needed. We are talking about a timer embedded in the signaling. By the way, the latter still needs to be enabled (option 16).
By using the SAFE item, the owner will have to press the key fob button - the ignition support does not turn on. Here it was about the procedure performed during operation.
First - the handbrake, then the button
Important was considered, one list remained:
- Turning on the ignition, the Valet button is pressed 6 times;
- Ignition turn off - the sound of sirens and 6 flares of the indicator will follow;
- The Valet button is pressed 1 time, a short siren sound follows, the button is pressed again, etc.;
- Choosing an option number in step 3, set a new value, for which any of the keychains is used;
- Car alarm can return to the "usual mode": it is enough to turn on the ignition or wait 10 seconds.
That is how, not otherwise, the STARLINE TWAGE A9 system needs to be programmed.
"Training" and the meaning of its use
Suppose each of the conditions:
- The engine control is carried out at a touchscreen;
- The sound starter sounds when automatic starts stops later than the motor is started.
Only if both conditions are made, it makes sense to conduct "training". System
"Learn" to recognize idling. The keychain for learning will not need.
Talk signal
These difficulties, in theory, are characteristic of any car alarm, and not just for the Starline brand systems. So, take patience.
Below is a sequence that is not in the basic instruction:
- Ignition include, the Valet button is pumped 9 times;
- Turn off the ignition - the indicator is constantly lit;
- Perform the start of the engine "from the key";
- When idling are installed, the VALET button is set 1 time - follows 1 siren sound;
- The indicator should go out - the training is completed!
When the alarm is trained correctly, it controls the motor without errors. By the way, the connection to the tank is recommended. That is, "simplify the task", moving to control over the generator, no sense.
Use the functions of the block
Consider a simple operation: how to turn off the sound in the remote control itself. Press and hold the 1-3 keys. The display will display the MUTE symbol, the vibration signal will follow.
Station speaker inside the console
Return everything as it was possible by pressing.
Now turn on the protection without sound emanating from the siren. Here the cursor method is activated: the 3 button is swing twice, and then by pressing the same button, move the cursor over the icons. Going to the desired label, the key 2. That is how the STARLINE A9 system is controlled.
It is known that not any car alarm is equipped with a built-in timer. From which it follows that the main keychain must be kept near the antennas. But to the system discussed here, this requirement does not apply. And yet, despite all the "pluses", you warn the reader about the following: the Starline TWAGE A9 signal does not use the dialog code. Reliability and simplicity settings are two important qualities characteristic of the TWAGE family. Need resistance to hacking - go to the Dialog family.
How the new keychain is prescribed
System Starline Twace It can be installed on cars with a voltage of battery 12V and a negative pole on the housing.
The central block is placed in the cabin in a hidden place, preferably under the dashboard - in this case the length of the connecting wires will be minimal. To prevent entering the moisture block, it is recommended to establish it in such a way as to eliminate the flow of water droplets on the wires inside the housing. Secure the block on a flat surface with screw screws or bilateral tape so as to exclude its movement during vibrations.
The transceiver module with an antenna fasten on the windshield of the car so that from the antenna to the metal parts of the body it was at least 5 cm. In this case, the maximum range of keychains is ensured. Also, when installing, it should be noted that the temperature meter of the cabin is in this module, so the module should be placed as far as possible from heat sources and avoid the sun rays on it. Otherwise, temperature testimony may differ from the real temperature of the cabin.
Remove the engine temperature sensor to secure on the engine housing under one of the M6 \u200b\u200bbolts available on the engine, ensuring good contact with the engine housing. The position of the sensor will determine the correctness of the temperature determination of the engine.
The impact sensor is rigidly fasten in the car, ensuring access to its adjustments.
LED indicator fasten on a prominent place on dashboard.
The Valet service button and the activation mode button set to the hidden, but available to the user.
When installing push-button switches under the hood and in the trunk, check the correctness of their operation. With a closed hood or trunk, the gap between the contacts in the switch should be at least 3 mm. Incorrect installation of push-button switches is often the cause of false alarms.
Conducting the wires as far as possible from the sources of electrical interference of the ignition, high-voltage wires, etc. Note that the wires do not come into contact with the moving parts of the design of the car - pedals, steering traction, etc.
Installation of electrical wiring connections must be made when the car battery is disconnected.
Attention! If the car is equipped with an air cushion or has a coded receiver, when the power is turned off, follow the instruction manual for the car or receiver.
All of all-point connections are performed using soldering and isolate well.
Connect the central unit and other signaling components to connect to cable connectors only after the installation is completed. Installation of alarm Machine in accordance with the connection scheme.
Connecting transceiver
The antenna transceiver module is connected to a five-pin connector located in the central unit under the folding lid, with a cable that is included in the alarm kit.
Connecting a two-level shock sensor
The shock sensor is connected to the central unit using a four-wire cable included in the alarm kit. Power supply (body potential) on the sensor is carried out only in the mode of protection. Sensor sensitivity in levels is regulated by potentiometers on the sensor housing.
Connecting a LED indicator
Connect the LED plug into the two-contact connector, located in the central block under the folding lid.
Connecting the engine temperature sensor
The engine temperature sensor connects to the central unit using a 2-wire cable. One of the cable wires, connect to an orange-gray wire (input of the hood key switch) of the 18-pin connector of the central unit, and connect the second wire to the car housing. Connection polarity is not important. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.
Connecting the 6-pin power connector of the central unit
Red wire (№4) - plus power + 12V, connect to a positive battery terminal.
Blue Wire (# 2) - Output Control Management, Connect the ignition Castle ACC terminal.
Yellow wire (№5) - Exit ignition support # 1, connect to terminal 15 ignition lock.
Green wire (№6) - Exit ignition support # 2. The output algorithm is programmed (Function 7). See "Temporary system work charts when remotely start the engine."
Black and white wire (№3) - the output control of the starter, plug the ignition lock terminal 50/1.
Black and yellow wire (№1) - the output of the starter lock control. Connect after the ignition lock from the starter side, having previously cutting the standard wire that runs from the ignition lock to the starter.
Connecting the 18-pin Central Block Connector
Red wire (№1) - plus power + 12V, connect to a positive battery terminal.
Black wire (№9) - minus power, connect with a car housing, ensuring good contact.
Green-black wire (№10) - Connect to lamps of dimensional lights or rotation pointers. Maximum exit load current 7,5A.
Green-yellow wire (№11) - connect to lamps of overall lights or turning pointers. Maximum exit load current 7,5A.
Gray wire (№13) is a positive output for connecting to siren. Maximum output current 2a.
Blue-black wire (№17) - Connect the doors closed on the housing to the button switches when opening the doors.
Blue-red wire (№7) - plug the doors to a + 12V button switches when opening the doors.
Orange-gray wire (№18) - Connect the hood closer to the hood when opening the hood. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.
Orange-white wire (№8) - Connect the trunk to the housing to the push-button switches when opening the trunk.
Yellow-black wire (№15) - negative yield of an additional channel number 1. The duration of the 1 second control signal. Maximum load current 300mA. The channel can be used to control the solenoid spilling trunk. The connection requires an additional relay. An example of a connection scheme is shown in the figure.
The yellow-red wire (No. 5) is a negative yield of an additional channel number 2. Maximum load current 300mA. The duration of the output signal pulse is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). Channel can be used to control additional equipment car. The connection requires an additional relay.
Yellow-blue wire (№14) - negative yield of an additional channel number 3. Maximum load current 300mA. The duration of the output signal pulse is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). The channel can be programmed to implement the function of two-step unlocking door locks or to control other car devices. The connection requires an additional relay.
Blue wire (№2) - negative yield of an additional channel number 4. Maximum load current 300mA. The channel can be programmed to connect to salon lighting or windows control module. The connection requires an additional relay.
Black and yellow wire (№4) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the protection mode is turned on, the operation of the turbotimer, the activation of the function of anti-grab, activation of the immobilizer. When remote and automatically start in the protection mode, the output is not turned off. It is recommended to use to lock the starter circuit. When connected, an additional relay is required.
Black and white wire (No. 12) - negative output of the status of alarm. Maximum load current 300mA. It can be used to block the engine with normally open (HP) or normal-closed (NZ) work algorithm. The connection requires an additional relay.
Black and Red Wire (No. 3) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the turbotimer and the engine starts. In start mode, it can be used to restore the locked engine circuits.
Orange-violet wire (№16) - negative status control input parking brake Or foot brake pedals. The lack of negative potential on this wire in the security mode will trigger alarm operation, and in the mode of running remotely or automatically engine - the engine stop. An example of a connection scheme is shown in the figure.
Serious-black wire (№6) - input control of the engine operation. Input resistance of at least 100 com. Input sensitivity - 1.0V.
Choosing a way of controlling the engine operation (Connecting a gray-black wire
STARLINE A9 alarm)
Motor Control by Tank
The gray-black wire is connected to the delta. The engine start diagnostics is carried out by changing the frequency of the tip signal. On the correctness of the connection of the black and gray wire, it is possible to judge the duration of the starter after turning off the starter during the engine start and receiving the start confirmation on the alarm key chain.
For proper connection A black and gray wire starter must turn off simultaneously with the start of the engine, regardless of the programmed starter scroll duration.
Motor control over the generator
The gray-black wire is connected to the generator output, which is connected to the lamp on the dashboard. Successful engine launch will be monitored by the presence of a positive voltage + 12V at the output of the generator with the engine running. When the black and gray wire is properly connected, the starter must turn off simultaneously with the start of the engine, regardless of the programmed duration of the starter scroll.
Attention! When a gray-black wire is connected to the generator output, it is used to use the quenching resistor 510 com ... 680 com.
Controlling the engine voltage on-board network
In case of the difficulty of detecting the chains of the band or generator, it is allowed to use the engine start monitoring mode over the on-board network. In this case, the gray-black wire does not connect and it is necessary to isolate it. Start confirmation will occur automatically after starting the engine. The disadvantage of this method of control is the fixed starter time. For proper operation of the starter without a twist, you will need to select the necessary duration, programming the function number 3 to the values \u200b\u200bof 800, 1200, 1800 or 3000 ms.
Connecting the built-in engine lock circuit
Run the chain between the ignition lock and starter. In the chain break, connect the black and white wire of the 6-pin connector from the ignition lock and the black and yellow wire 6-pin connector from the starter side. The maximum current of the built-in lock relay is 40a.
Connecting an external engine lock circuit using conventional relays
Run one of the standard engine start circuits and connect the additional relay into the circuit break. The type of contacts of the NR lock relay (normally open) or NZ (normally closed) is programmed (function 15). Initially, the factory is programmed by the NZ Type of Relay Contacts. An example of a connection scheme of one of the chains is shown in the figure.
Connecting an external engine blocking circuit using a Universal Starline Wireless Lock Set
This method of blocking the engine significantly increases anti-theft alarm properties. To control the module included in the Universal Starline Wireless Lock Kit, use a black and white alarm wire, pre-programmed it on a normally open (HP) type of contacts. Possible engine blocking schemes are given in the installation instructions for installing the Universal Wireless Lock Starline.
Connection to Solenoid Unlocking Trudge
Alarm has an outlet for remote spilling trunk (yellow-black wire). Maximum load Exit - 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connect to salon lighting
An additional alarm channel 2 can be used to connect to the neighbor headlights and the implementation of the "Lightway" function (yellow-red wire). The maximum output load is 300 mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connecting an orange-purple wire on cars with manual and automatic gearbox
On vehicles with manual gearbox, connect this wire to the parking brake button switch, which closes to the housing when the brake is turned on.
On vehicles with automatic gearbox, connect this wire to the brake pedal button closed to + 12V when the brake pedal is pressed.
The alarm has an output that can be used to connect to salon lighting and implementing the function of the "polite illumination of the cabin" (blue wire). The maximum output load is 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connecting to neighbor headlights
Connect to the central locking system
Starline Twage alarm has built-in central lock control relays. Relay contacts are displayed on a 6-pin connector. Load capacity of built-in relay 15a. The duration of control pulses is programmed (Function 9).
Connection CHEMA to the locking system with positive or negative control
Connection CHEMA to two-wire locking system drives
CHEMA connection to a pneumatic locking system
Driver Door Activator Connection Diagram for Door Double-Step
Connection schemes
Connecting the 6-pin motor autorun connector
The SRARLINE A9 security complex is characterized by the presence of such functions as autorun, anti-primilation, as well as panic and others. A9 contains the sections needed for mounting and setting up the system. Before starting the installation of the complex, you should carefully examine the management and think about the location of the components.
[Hide]
Technical characteristics A9.
Starline Twage Car Signal Model has characteristics:
- operating frequency of the radio transmitter - 433.92 MHz;
- radius of signal feed communicative keychain (with display) - 600 m;
- radio reception by the pager signals submitted by the head unit - 1200 m;
- the distance of the auxiliary control panel is not more than 15 m;
- type of sand sensor design - piezoelectric element;
- the permissible temperature of the head unit is from minus 40 ºС to plus 85 ºС;
- voltage on power terminals - not higher than 18 V and not lower than 9 V;
- current taking by alarm in standby mode - 0.25 mA.
The stated flow and reception distances are achieved only in the open space. In urban development and with no interference, the reception distance is reduced several times.
The design of the Tweez A9 head unit mounting boards allows the operating current values \u200b\u200bindicated in the table.
Equipment
The mounting set includes:
- a keychain-communicator equipped with a liquid crystal screen and a receiver-transmitter for two-way communication;
- auxiliary key chain, working only on the transmission of signals;
- the main unit, which includes the control processor and the relay module;
- antenna module (with an additional transmitter and temperature sensor);
- temperature sensor B. motor compartment;
- adjustable shock sensor;
- control diode;
- tuning and service button with wiring;
- control key of the anti-label function;
- terminal dispersion;
- a set of connective harnesses;
- technical documentation, including the Installation and Setup Guide.
A9 alarm is supplied in a cardboard box, the components are laid in a foam substrate, protecting parts from shocks.
Photo Gallery
The photo shows the type of components included in the alarm set.
General Type of Supply Set Dismantled with car set Additional control panel Main keychain
Main features
Key features provided by alarm:
- The security complex creates several individual protection zones by car. Separate zone is protected by electrical circuits to ensure the start and operation of the engine. The end switches are triggered with unauthorized unlocking doors and releasing the parking brake lever. The shock sensor performs the protection of body panels and glasses from damage applied. Additionally ensures the protection of the chains and the ignition lock.
- The head processor unit has a non-volatile memory that saves the state of the system when the power is turned off.
- Built-in anti-primilation mode. It is activated by a button on the keychain or a separate key set.
- Panic mode with remote activation.
- Functions of an additional immobilizer and built-in turbo-timer.
- Automatic start and heating of the motor at a distance and on the laid program.
- It is possible to extend work power aggregate With the keychain.
Installation Instructions
- Installation of the complex is carried out on vehicles equipped with electrical scheme direct current With a voltage of 12 V. The negative pole is connected to the bodybuch.
- All connection work is carried out with disconnected battery terminals.
- Before turning off the power, you need to get acquainted with the recommendations of the car manufacturer relating to the system of inflatable airbags and standard radio (device encoding).
- The elongation of wiring harnesses should be carried out by a conductor from a similar material with a cross section of no less source.
- The wire connection is recommended to be disappeared, and then protected by a tape or shrink tube.
The literacy of the layout and accuracy of the installation depends on the further operation of not only alarm, but also the entire electronics of the car.
What do you need?
The minimum set for mounting includes:
- instructions for Starline A9 on installation and configuration;
- self-tapping screws or screeds (preferably several sizes);
- bolts M6;
- wrench or end heads (set);
- plastic blades;
- broach for wires through the engine shield and car interior;
- drill and set of metal drills;
- installation and insulation materials;
- pulbs for removing isolation if you need to eliminate wiring.
Connection schemes
Below are the main component connection schemes. Detailed information is available in the Installation Guide.
General compound scheme Auto-starting module Block of the Central Castle Solding sensors
Step-by-step action
Approximate component installation sequence:
- Disable terminals from acb. For this, the wrench must be loosen the clip at the battery output.
- Place the processor block system in the hidden cavity of the car, protected from moisture access. Usually, the node is placed inside the instrument panel, on the removal of the aircraft climatic installation. The location is selected in such a way as to eliminate the flow of condensate on the wires inside the connector. The block is fixed to the metal frame of the panel with screws or tie through the regular attachment points. Installation is allowed using bilateral tape.
- Place an antenna node on the inner surface of the windshield at a distance of at least 45-55 mm from metal body panels. If the glass has a metallized film, the module is recommended for free space. Only in this case the maximum range of the transmitter and the receiver is achieved. When installing antenna, avoid places exposed to sunlight. This is due to the presence within the temperature sensor module. Overheat item will report inaccurate information.
- Install the temperature sensor on the block or motor head using a regular bracket. The hole is designed for the M6 \u200b\u200bsize bolt. The installation point should provide a good thermal contact, because this data runs autorun.
- To place Siren under the hood. The node is installed by a shore down at a point inaccessible from the bottom of the car or through the wheel arch. If the owner uses autonomous siren, it is necessary to provide unhindered access to the larch of the Deactivator Castle.
- Sensor hit in the cabin. Mounting place should not prevent access to adjustable potentiometers.
- Install the indicator diode on the dashboard or facing of the front racks. Details are allowed to drilled in advance with a drill hole.
- Thinking through the installation location and mount the buttons of service and anti-grab. The location of the devices should provide quick access to them.
- Install end switches on doors. Decorative upholstery is removed using plastic blades.
- If it is necessary to establish end swipes under the hood and lid of the trunk. When installing, it should be gap within 3 mm and more between the contacts (with covered covers). With a reduced distance, the risk of false positives occurs. The place of installation of the opener should not be in the zone of the cluster of rainwater.
- Using the broach, pave the wiring to the main alarm elements. The gasket route must be kept on the removal from the ignition system and other interference sources.
- Connect wiring harnesses in accordance with the schemes. The head module should be connected last.
- Imagine all connections.
- Turn on the power and program the system in accordance with the recommendations set forth in the instructions.
User's manual
Download user manual and installation StarLine A9
Designation of buttons and icons on the keychain
The purpose of the button A (nearest to the antenna is mainly with the icons of locks on an additional communicator):
- switching on and off protection (including when a power unit running);
- direct autorun and motor stop (only on the main keychain);
- search for a car (together with the B button).
The B button (average on the main remote and with the key icon on optional) is used for functions:
- confirmation of the label selected by the cursor;
- unlocking the luggage compartment;
- auto-starting and engine operation time (optional only);
- choosing a autorun mode (on an additional remote), etc.
Button with (with pictogram open trunk) is used for:
- cursor movement;
- shutdown signal sounds;
- keychain settings (including buttons a);
- timer programming;
- machine search (for an additional console).
The D button installed only on an additional remote control is necessary in some cases:
- silent system management;
- enabling additional functions (collaborated with other keys).
The screen has labels of functional and information destination. Functional icons are selected by the cursor method and pressing the buttons turn on or disconnect various modes of operation. Information indicators displays the current status of the functions of the security complex.
Display with labels on the STARLINE A9 key chain
List of functional labels on the screen:
- A - mapping the function of the anti-grab;
- B - the work of Dopcinal 3;
- C - automatic launch of temperature values;
- D - turning on the motor according to the data from the alarm clock;
- E - engine launch at a distance (keychain);
- F - switching on and off protection without filing Siren signals;
- G is the standard mode of operation (with lilac);
- H - disabling shock sensor at a distance;
- I - service mode;
- J - Displays the temperature in the cabin, as well as a survey of the condition of the car;
- K - the work of Dopkanal 2;
- L is remote control of the drive of the luggage compartment lock.
Information icons:
- 1 - the state of the battery installed in the keychain;
- 2 - inclusion of DPKANA 2;
- 3 - automatic launch depending on the ambient temperature;
- 4 - working force unit;
- 5 - the lid of the trunk;
- 6 - open the terminal side doors;
- 7 - vibration;
- 8 - tuning mode;
- 9 - the function of automatic resetting of the protection of active;
- 10 - protection without feeding sound signals when alarm;
- 11 - standard protection regime (with lilac);
- 12 - open the hood ender;
- 13 - Detection of a strike on the body or windows (various mapping for the first or second sensitivity zone of the sensor);
- 14 - indication of the active parking brake;
- 15 - turning on locking locks on the doors;
- 16 - disabling lock lock;
- 17 - indication of the standby mode, in which only the receiver of the control panel is active;
- 18 - turns on when sending a command;
- 19 - There is a challenge from the car's salon;
- 20 - actively reduced energy consumption by keychain;
- 21 - ignition activation;
- 22 - inclusion of alarm clock;
- 23 - indication of time after lunch RM;
- 24 - similarly - before dinner AM;
- 25 - Start on the signal from the alarm or daily;
- 26 - Displays additional information;
- 27 - selection of temperature measurement scales;
- 28 - Indication of the countdown timer.
How to set up a key chain
The setting sequence is:
- Press the button with select the desired function icon.
- Drown and keep the key from for six seconds during which the buzzer will give a double, and then a triple signal.
- Check the operation of the programmed function by pressing the button A. If the owner is required to change the key assignment, the rewriting procedure has a similar view.
Only the first button (a) of the main console can be adjusted. The owner can choose and assign options for this key unlimited number. The standard solution is to set to enable / disable security mode.
The button B does not have a hard binding to execute any command. It is used to confirm the function selected using the C key. Additional control panel is not programmable.
Installation of watch
The procedure is as follows:
- Drive the C button and hold it until the dual signal is fed and started flashing the indicator field of the clock on the screen.
- You can change the value by pressing a (zoom) or in (reduce). For an accelerated clock translation, the button hold is used.
- Press and similar to set the value of minutes.
- Re-use the C button to hold the sound signal confirming the output from the setting. It is possible to automatically exit programming, waiting a few seconds, during which you should not press the keys.
Entering the alarm data memory is somewhat different from the clock setting:
- Drink the button C and hold it until the dual signal is supplied.
- Clicking on with choose a closure label, after that it will flash the configuration field for the awakening time.
- By analogy with the clock, make the value of the signal on.
- After that, an additional an alarm on / off will appear in the menu. To activate, pressing on A, for shutdown - on V.
Active alarm clock on the STARLINE A9 keychain screen is displayed by a burning label. When triggered, a melodic signal is supplied, which is interrupted by pressing on C.
Setting up autorun.
In order for the owner to use autorun, you need to configure the transmission type when installing the head unit. On the housing of the node there is a connecting loop that must be cut (in the case of mechanical transmission). If an automatic is used on the car, then the loop remains closed. The type of motor is laid when programming block. For the correct launch of a diesel engine, a pre-warming of candles is required, so the starter response delay is set.
Before you need to perform the conditions:
- turn off the ignition;
- raise the parking brake lever;
- close all body elements equipped with trumps from alarm;
- install the program neutral position of the box of the box (only on the mechanical transmission, not required on the machine).
Brief instructions for setting neutral in memory block:
- Stop the car on the site of the scheduled parking lot, leave the ignition active.
- Translate transmission control lever to a neutral position, and then activate the parking brake.
- Disable ignition. With the correct procedure, the engine will continue to work.
- The owner has 0.5 minutes to leaving the cabin vehicle. After closing the door, you need to activate the mode of protection according to the standard diagram. The motor will stop instantly either continue to work within the turbotimer mode. If the owner does not include protection, the engine will operate 0.5 minutes or before turning off the programmed turbo-player.
The neutral installation procedure is performed before each alleged auto start.
On some cars there are features of the design, requiring activation of support for the operation of the power unit:
- After stopping the car and translating the lever of the box to neutral, you must press and hold the button A on the keychain.
- Wait for a triple outbreak of overall lights and turn on the melody to the built-in buzzer. The label of the functioning motor is activated on the screen and the operating time will be displayed. In the case of deactivated turbotimer, the text of the type "R00" is included.
- Disable ignition and remove the key from the lock, the power unit must continue to work.
- Further actions are identical to the usual neutral setting (described above).
On alarm clock
Before starting, you need to set the clock and the alarm value.
The setup procedure is simple:
- Button with select the desired icon and confirm the execution of the KE key
- Wait for the supply of a single signal with lilac and dimensions, after which the melody will be played. Two labels will be active on the screen, and the diode will start working a series of two outbreaks.
Starting an alarm clock provides for a single warming of the power unit in the programmed time.
The start time of the power unit according to the alarm clock and the moment of inclusion of the alarm itself does not exactly match. The reason is the rounding of minutes to a dozen during the operation of the autorun.
By timer
Programming is as follows:
- Choose the cursor method the desired shortcut and confirm the action.
- A confirmation will be a single beep of lilac and a flash of light alarm lamps.
- Immediately after that, the first start and engine warming will occur. Repeat launches will be performed 24 hours after the first start time. In case of an error, at least one start, an automatic cancellation of the subsequent heating of the power unit occurs.
Timer Start is the ability to run a power unit daily at a certain time. With an unsuccessful start, the function is turned off, it must be activated again.
By temperature
Step-by-step programming is as follows:
- Move the cursor to select the desired icon on the channel screen.
- Confirm the selection of the function by pressing the button. Get a confirmation signal of the melody, at the same time it should work outward light alarms, and a short siren beep will sound. The display is activated by the mode icon and the threshold temperature value is displayed. An additional confirmation will be an indicator diode that will go into operation mode of three outbreaks.
If you want to deactivate the function, then this is done according to an identical procedure. Confirmation is a double sound and light signal feed, ringtone buzzer and disabling the label on the screen.
When the motor start starts, the alarm uses information from the sensor installed on the engine block or in the engine compartment. The sensor has four settings in the range from -20 ºС to -5 ºС. Additionally, the operating time of the motor and the number of repeated launches, which can not be more than 12 per day. There is also a time limit between starts - at least 1 hour. At the same time, it occurs from the moment of the operation of the power unit, the duration of the heating period does not affect the settings.
The owner should be remembered by two rules for using autorun temperature:
- numerous motor starts lead to the battery discharge;
- if an unsuccessful engine start attempted, the continuation of the cycle is automatically canceled.
How to bind a new key chain to Staline A9?
Step-by-step instruction:
- Enable the ignition of the car, and then click and hold the login button in the settings.
- After filing four beeps, the alarm is released to release the button.
- Take a key chain and press two buttons at the same time. On the main remote, the A and B key clicked, on the additional - C and D. Confirmation of it in memory will be a short signal filed by a lilac complex.
- Repeat the previous item for all programmable devices. It is important to withstand the time interval between the keychains in memory, which should not exceed five seconds. In case of violation, the programming procedure is automatically interrupted. The console number in memory is displayed by the number of confirmation of the beeps.
- After recording the last code, exit the setup mode by turning off the ignition. It should be five times to work out external light alarm.
- Check the performance of the remote controls.
In memory of the head block of the system keychains is required if additional remote controls are purchased. In total, it is possible to bind four communicators, when you try to write the fifth, it is deleted from the memory cell of the first device. This is due to the cleaning of the storage module, so new and old consoles should be prescribed.
The video tutorial on the reference of the console to the STARLINE A9 system is provided by the "Raccoon and Panda" channel.
Advantages of alarm
The advantages of the security complex include:
- function of automatic start of the power unit;
- an additional channel that allows you to expand the system functionality;
- built-in temperature sensor inside the car cabin;
- ease of installation and settings;
- loud built-in buzzer buzzer.
disadvantages
According to the reviews of the owners, the alarm has disadvantages:
- there is no possibility of performing repeated starts through programmable time intervals;
- small radius of receivers and transmitters in urban conditions;
- the command encoding is made according to an outdated algorithm that is easily intercepted and decoded;
- cases of acquisition of alarm with an incorrectly operating head unit are noted;
- weak housing keychain, the support elements of the buttons are destroyed;
- software malfunctions are possible.
How much is?
The approximate cost of the STLINLE A9 signaling is indicated in the table.
Video "Programming SRARLINE A9 alarm"
An example of setting up the STLINLE A9 security package is presented in the videot of Anton AUTO.
Starline Twage A9. - Automobile security complex with a 2-sided communication radio channel and remote engine start. Communication range in open area - 600m with keychain and 1200m in pager mode. Coding of control radio signals dynamic.
System Starline Twage A9. It can be installed on cars with a gasoline, diesel or turbocharged engine, with an automatic or manual gearbox.
Starting the engine can be carried out by a command of the keychain, on the temperature sensor installed on the engine housing, in time every 24 hours and at any time of the day. Control over the operation of the engine can be carried out by the signal signals, generator or by changing the on-board network voltage.
In alarm Starline Twage A9. The function of determining the temperature in the passenger compartment is preserved, the second temperature sensor is set in the signaling transceiver, which is usually attached to windshield Or is installed under the torpedo. For many owners of Star Line systems, it has already become a habit to communicate with your car, sending him a Check team. In response, in addition to full information about the enabled mode of protection and the state of the sensors, the temperature in the car is displayed on the display. For example, in the summer, seeing that the temperature in the cabin rises above the laid, you can remotely start the engine, and therefore air conditioning, for air conditioning.
Description:
- feedback
- engine starting
- trinket remote control Included 1.
- keychain-pager with LCD display included 1
- the remote module is to increase the connection radius.
- communication module included
- consemist included 1
- valet switch button included
- anti-Hi-Jack switch button complete
- vibrating alerts on the pager key chain
- maximum radius of the pager channel 1200 meter
- maximum range of block channel D / U 600 meters
- valet mode
- "Panic" mode
- passive immobilizer mode is programmed
- personal PIN emergency shutdown code
- disconnecting sensors when arming
- disabling the warning zone of sensors when arming
- finding a car in the parking lot
- active Anti-Hi-Jack
- passive Anti-Hi-Jack
- bypassing a faulty zone
- entry for an additional sensor
- hood / trunk entrance / trunk
- number of engine locks 1
- external Engine Lock Relay 1
- programmable engine lock (NZ or but) 1
- pulse duration for electric locks 0.8 seconds.
- pulse duration for pneumatic locks 3.6 sec.
- other possible centerpieces management pulses (open / close) 0.8-2x0.8 / 0.8-30 seconds.
- exit to dimensions 2
- exit to the trunk lock is programmed
- fM Managing Code Type
- output of the control of El Doors of the Power
- number of extra beds 4
- additional channel I 1 sec.
- additional channel II 0.8 / 10/130 / Latch sec.
- additional channel III 0.8 / 10/130 / Latch sec.
- additional channel IV salon. Changing / Flods. sec.
- comfort mode is programmed
- mode "Turbotimer" 1/3/6 min.
- running the engine by timer 24 hours
- running the engine at -5 / -10 / -15 / -20 degrees.
- the program "Neutral" for MCPP is
- starter start delay for diesel 4/6/10 seconds.
- starter time when starting the engine 0.8 / 1.2 / 1.8 / 3 sec.
- engine warming time after starting 10/20 / 30 / without limit min.
Starline A9 equipment:
- Control block
- Keychain S. feedback With LCD
- Keychain without feedback
- Stroke 2-level shock sensor
- Engine temperature sensor
- Antenna module
- Kontevik Kapota
- LED indicator
- Service Button Valet.
- Anti-Hi-Jack mode mode
- Wire set
- Instructions for installation and operation in Russian
- Starline A9 Color Memo
