What oil pour into Logan 1.4. Recommended motor oil for Renault Logan. Oil selection by type, parameters and brands

From this article you will learn how to replace motor oil in Renault Logan., Replacement frequency, which oil to fill in 1.4 and 1.6 liter eight and sixteen valve engines.

So, let's begin.

Maintenance No one canceled

Renault Logan is one of the most popular cars in the budget segment. Inexpensive, unpretentious and quite reliable, he won recognition among motorists.

But, like any other car Reno Logan. Requires periodic maintenance, moreover, these are all components of the car - power plant, transmissions, chassis, body, etc.

Concerning power aggregate, perhaps, one of the most important maintenance operations is to replace the oil.

While the car is under warranty, these works are included in the list. serviceBut after the end of this warranty, the execution of this operation falls on the shoulders of the car owner.

However, the replacement of oils - the operation is not so complicated to contact the specialists every time, because it is possible to fulfill it on their own, saving money.

When to change what and how much to pour?

Let's start with the fact that the frequency of oil replacement in this car, which is installed by the manufacturer, is 15 thousand km of mileage. But this is if such a mileage car passes throughout the year.

If for the year it does not pass such a distance, then the oil will still have to be changed, because the manufacturer's documentation indicates that the oil should be replaced once a year, even if the car is practically not operated.

As for the lubricating material itself, here the manufacturer shall indicate the ELF manufacturer oil recommended for use in the engine.

It is this company that fills materials in official service centers.

For engines installed on Renault Logan, it should be purchased with a viscosity of 5W30, 5W40, 10W40.

As for the number of poured lubricant, it all depends on the power installed used and its constructive features.

For motors with a volume of 1.4 and 1.6 liters with an 8-valve timing, it is necessary to prepare 3.3 liters of oil, and for the unit for 1.6 liters, but 4.8 liters are already required for the C16-valve GDM. It is necessary to take into account before starting work.

In any case, the oil is better to acquire a bit with a margin so that in the trunk of cars there was always at least 1 liter on the tank.

Also a new lubricant to buy better in obviously proven and reliable points of sale.

The amount of lubricant poured lubricant is approximately.

The fact is that when plums, the oil remains in the engine, so it is not always necessary to pour the specified amount, but to control it with the help of the probe.

What else do you need?

During this operation, the oil filter is also performed.

You need to acquire a filter with identification number 7700274177 or 8200768913 they are interchangeable and are original for this car.

But you can buy any filter, the main thing is that it is a well-known manufacturer, and also approached overall parameters.

But if it was not possible to get this, then instead of an old gasket, set the usual copper appropriate diameter.

About washing the motor.

Recently, a hundred began to indicate that when changing, it is necessary to wash the motor.

It really needs to be done, but only if the oil of another manufacturer will be poured.

If the manufacturer of the lubricant does not change, then the flushing should be carried out.

What you need for work

Now consider how this operation is performed on the car with an 8-valve 1.4-liter engine Logan.

To perform all the work, you should not need much:

• Special key in the form of a square by 8 or 10;
• Special key to remove the filter;
• Capacity for drain (preferably widespread);
• New lubricant in the desired quantity;
• New filter;
• Westes.

Having all this, you can proceed to work. The sequence of actions is as follows:

1. Auto is installed on a flat pad and immobilized. Then the engine is heated so that the engine oil in the engine has become more liquid. But it is not completely warming up, but to a temperature of 50 degrees. With, no more, otherwise you can get burns;
2. The hood opens and the lid of the oil refining neck is unscrewed. If this is not done when the oil flows inside the engine will form a vacuum, due to which the duration of the drain will significantly delay;
   
3. A car in the bottom of the bottom protection was done by the technological hole for accessing the drain plug, so the protection does not have to remove. A plum plug on the square key on 8 or 10. Sometimes she sits tight enough, so it may be necessary to increase the key with a cut of the pipe;
4. Slightly sending a plug, you need to install the prepared container under it, after which the plug is completely unscrewed. At the same time you need to try not to miss it into the container. This is one of the most dirtiest stages of work, because part of the oil will necessarily fall into the hands therefore put on them rubber gloves;
   
5. Further is expected until the exhaust lubricant is completely solved. At this time, the plug changes on the traffic jam. Having finished with the drain, we set the plug in place and tighten it well;
6. Go to the pumproom space. An old filter is unscrewed by a special key counterclockwise. After planting place thoroughly wipes clean rag;
   
7. Before installing a new filter, it needs to be filled with an oil by half, also lubricates the sealing ring installed in it. After that, the filter is installed in the location spinning. When tightening the key is optional, it is possible to tighten the hand with force;
8. Pour oil into the engine. Initially, only 3 liters are poured. After you wait until the oil is completely falling into the pallet, to measure its quantity. Gradually, the rest of the oil is brought to the right level. The right level is the level when the oil on the diploma reaches the middle between the marks of MAX and MIN. The main thing is not to pour. If the level is approached by the MAX mark, nothing terrible, but if it is more - you have to push off too much;
   
9. After the fill, we launch the engine, let it work 3-5 minutes. After that, wait until the lubricant stalks into the pallet and check the level again, when necessary, adjust it. You should also check the filter and drain plug for the presence of outers, if any, then the suspender should be made.

Nuances of replacement on the 16-valve motor

As for the 16-valve engine, in addition to the amount of lubricant poured, there is another nuance - access to the oil filter.

The fact is that you have to re open space A protective screen of the exhaust manifold will interfere, and the protective crankcase is below.

Something one for access to the filter will have to shoot, but what - to solve the owner of the car. Otherwise, the sequence of work is identical to the described.

Finally, several useful Soviets.

The key to remove the filter is usually needed only to dismantle, it is not needed when installing. Therefore, it is not necessary to have it at hand.

If the filter is not unscrewed, but there is no key, you can simply gently pierce its body with a screwdriver, plug it inside until it stops, and unscrew the filter using a screwdriver as a lever.

If the oil accidentally passed, then it will be much easier to pump it, using a tube from a dropper and a syringe, because unscrew the tube and drain the part of the oil is very vigorously and uncomfortable.

The syringe, the larger the volume - the better, the dropper tube is worn, necessarily with the retainer. Then the tube is lowered into the hole under the probe and the syringe pumped up excess oil.

As you can see, replace the oil on Renault Logan, no matter how the engine it is equipped, it is simple enough, and even a novice motorist can perform it.

1.4 and 1.6, which have a 16V system, need a timely replacement of oil every 10,000 mileage kilometers. Some owners do not comply with these rules, which in turn leads to premature engine wear. To implement right choice Oils, find out how much you need to be replaced, you should be guided by a sheet of special tolerances of Renault Logan. In this article we will talk about the procedure for replacing the oil in motors 1.4 and 1.6 - 16V.

Selection procedure

The main criterion for buying is its viscosity. The use of viscosity with a high indicator leads to the rupture of the oil film, especially during the cold season.

The volume of the canister varies from 1 to 5 liters, so you can easily acquire as much as your car needs.

Of course, for new motors 1.4 and 1.6 - 16V, you can use with a smaller viscosity indicator. This is determined by the fact that the gaps in the rubbing pairs of the new unit have minimal values, respectively, more fluorescent lubrication will easily reach the place of increased load.

Also, it is necessary to acquire a fluid that has a low viscosity coefficient for engines that have completed overhaul. As a rule, mileage before the first replacement will be about 1 thousand kilometers, since this resource is considered to be running.

But for the engines 1.4 and 1.6 - 16V, which passed about 100 thousand mileage kilometers, the engine oil must be poured more thick, as the gaps between driving items have a greater value. Accordingly, such a fluid will protect the motor components better and will give a solid film in high friction places.

Purchase motor fluid It is necessary to produce in specialized stores with a certified product. In the case of buying low-quality oils, you risk damage to Logan, which will lead to expensive repair of motor parts.

As a rule, experienced sellers in large auto stores will tell you how much butter and which one is needed for your car. Usually the experienced owner knows which oil is needed and how much to pour it into your car.

There are special additives that significantly reduce friction and contribute to the continuous operation of the motor at elevated loads. Among them are molybdenum, which is supplied separately and already existing in the canister. To know how much this additive is needed to fill, you need to know the volume of the necessary fluid for your engine.

Talk about the replacement procedure

Many owners of cars Logan decide to apply for such work related to the change of engine fluid.

We recommend that you replace themselves and control this process completely on our own. Such a process is not difficult with the exception of some features that need to know and observe during these works. To fully protect yourself, use dense clothing to avoid burning hot liquid, since at the time of work, the engine engine must be heated to the operating temperature.

So, let's start performing the procedures for replacing motor lubrication.

Follow the rag because this work It is a very dirty process.

1. To begin with, it is necessary to provide access to the car from the bottom, for this you can use the automotive lift or garage overpass.
2. Commmise to the car and dismantle the plastic protection of the crankcase. To do this, unscrew three bolts in the front of the bumper, after which the dismantling of two more fasteners behind the protection. Pull the plastic casing to the side rear axisThereby you dismantle this item.
3. First of all you need to dismantle oil filterSince its channel is located in the upper part of the lubrication artery.
4. Take advantage of a special dismantling puller oil filtersIf you do not have any, you can use sandpaper. Wrapped this element around its axis with sandpaper, make it unscrewing it counterclockwise.

Another way to unscrew the oil filter is the use of a conventional screwdriver, which you want to break through the filter element and use it as a lever. Previously, you need to put a special container in order not to drench hot oil.

1. Make a lubricant of the sealing rings of the filtering element and install it in place by spinning by hand.
2. Unscrew the drain plug in the engine crankcase, then make a drainage of waste fluid into a separate container. Wait until all the liquid stalks, only then make a replacement of drain plug and sealing ring on it.

Attention! Take care in advance about the utilization of the spent lubricant.

1. Clean the drain plug, not allowing the sample, otherwise you can damage the thread of the aluminum crankcase.
2. Install the crankcase protection, pre-cleaving the item from excess dirt. Install the installation procedure in the reverse order of its removal.
3. Open the Logan hood, then remove the filler plug on the valve mechanism cover. By choosing the desired canister, pour fluid in the amount you need.

If you do not know how much to fill, use a special directory to allow 1.6 and 1.4 - 16V liquid volumes.

1. To know how much you already flooded, you need to use a special probe, which is installed on the car. On this probe, labels are applied, which determine the required level of volume of fillible fluid.
2. Set the level to the maximum probe threshold, then run the engine for a few minutes. After a short work of the engine, stop it and waiting for some time, make a level control to know how much it is necessary to attach.
3. Tighten the plot cover into place, after which the work can be considered complete.

Observe the safety regulations in order to avoid injury.

Conclusion

Now you know not only which oil and how much it is necessary for your favorite, but also how to correctly change it with your own hands. Premature oil change leads to better resultsSince the wear products are not in the lubricant. Buy high-quality components having a certificate of conformity and admission for your car. To protect yourself from low-quality lubricant products, buy spare parts in large auto parts stores.

Observe the viscosity parameter of the oils in accordance with the time of the year, so you will extend your life to your car. Do not tighten with timely maintenance and carry it out every 10,000 mileage kilometers.

After reading this article, you can use it as an instruction for holding it with your own hands.

Good afternoon dear friends! If you are the owner of Renault Logan, then I have a hurry to congratulate you immediately - this article is exactly for you. For the rest of motorists, it will be clearly familiar with its content too. We all know that timely replacement fresh oil is the pledge of long and successful work Motor. Here about this and talk today: Renault Logan Oil (Renault Logan), how to choose it correctly and about other replacement features. By the way, I have previously published an interesting material about which oil I poured at a distance of 90,000 km. and.

Briefly for reference:

On this car, the manufacturer was installed the following engines:

• 1.6. Lithing K7M710, K7M800, which has increased piston running.
• 1.4 liter, which can be 8 or 16 valves.

The engine can spend up to 0, 5 liters of oil per 1000 km, so sooner or later we will have to face it with a plot. Full replacement The manufacturer recommends conducting.
From the manufacturer's instructions, it follows that 1.4 liter 8 valve unit requires only 3.35 liters of lubricant. At the same time, the volume of oil for 1.6 liter will need much more - as many as 4.80 liters. There are certain recommendations for a variety and lubricant manufacturer, which are provided by the Renault plant itself. This is an ELF EVOLUTION 5W40 or ELF Evolution 5W30.

Checking the oil level

Let's start with how to check the oil - is it still suitable for operation or have long been replaced? It is desirable to produce such an operation on a cold engine. If he recently worked, it will take at least a 10-15 minute break for its cooling and in order for oil glass into the crankcase. The car should stand on flat terrain or playground, otherwise the level will not display the real situation. For measurement is used special Propertywhich is located near the head of the cylinder block under the hood.
The dipstick is first wiping with dry rags, after which it is neatly introduced to the previous place. After a few seconds, it can be reached back and measure the trail that will leave the oil border. Its level should be located between the MIN and MAX marks. In case the oil is below the minimum mark, then it urgently requires its topping. It must maintain a light brown, transparent shade. If it is too dark, it speaks of the developed resource and pollution. The answer to the question how many liters of lubrication will need to buy with a complete replacement, will serve as the calculated volume of the oil system in the engine. As mentioned you, for Renault Logan, this is either 3.35 or 4.8 liters.

What products prefer

First, consider which oil recommended by the manufacturer better corresponds to operation in domestic conditions. Let's start with the fact that the recommended Lubricant ELF is also a French brand. Products 5W30 differs in energy-saving properties, as evidenced by the corresponding sticker on the package.

Most of all it is suitable for those power units that are not equipped with a turbine, were not forced and not at all exploited, or have a small resource passed. It is for these cases perfect suitable oil With low viscosity at high temperature modes. This type of engine oil provides a thin oil film, but for new engines this is sufficient, but this reduces fuel consumption.

But for pretty worn engines characterized larger gaps that need to be carefully filled, and for this best oil - That which has a greater density. What should it be? Optimal decision there will be a grade that is advised to use in the used engines, forced and diesel engines. It is for these purposes that will need a lubricant that is characterized by a low viscosity at high temperatures. It is due to increased viscosity that the oil film does not break up, which allows a little to save the volume of oil consumed by the engine.

The concept of admission and postcontrol

Another interesting criterion is the so-called tolerance lubricantwhich is part of the certification process of this product. This is a complex procedure, the result of which is a special certificate - on its basis the manufacturer can make the appropriate label on the etiquette. This parameter is necessary for the lubricant to compete with other factories. However, it is impossible to say unequivocally that one or another variety is the only suitable for concrete brand Auto like in this case For Renault Logan.

After the oil change was made, it is necessary. It is desirable that it be slightly lower than the maximum mark. In case of overflow, the excess can be accurately merged. If a control lamp I did not go out immediately, you should not panic - this is a normal phenomenon. Now you need to start the engine and give it to work on the "idle" for about 5 minutes, after which check the oil level again. It remains to measure the kilometer on which it happened and can be sent on the road.

Add to the number of subscribers of my blog, and I will also be grateful for feedback among your acquaintances. Ahead of us will be waiting for a large number of interesting materials on car themes. Until!

RENAULT LOGAN is a specially designed subcompact car model for young and developing countries. The main production has been established in Romania. In the CIS countries, assembly workshops are open only since 2005.

The line of power units does not shine a variety: gasoline motors With 1.4 and 1.6 liter volumes and one diesel in 1.5 liters in eight and sixteen valve execution. Motor layout front, front-wheel drive with 4 × 2 wheelchair.

In general, the model is characterized positively, its resource is leaving, there are no special complaints. Of course, subject to the main rules and instructions on the operation. Recently, there are many questions on the topic, which oil is pouring into the engine Renault Logan. Obviously, this is due to a wide range of products in auto shops and owners difficult to make the right choice. In order to provide methodical recommendation, Consider the types of oils allowed by the manufacturer.

Oil selection in Renault Logan Engine 1.6

You can pour any oil into the engine, that's just not every one of them approach and benefits. At this stage, many inexperienced motorists commit typical mistake - poured what is cheaper. Frequent cases of economy money On the periodic inspection. Motivation of such ignoring is very different, starting from the desire to save up to personal scattered.

So which oil needs to be poured. A clear answer to the assigned question gives instructions for use - Elf Evolution SXR 5W40 or ELF EVOLUTION SXR 5W30. It follows from this that only the synthetic base, and regardless of the type of power supply system of the power unit.

Choosing an oil in the engine Renault Logan 1.4

What oil pour into the engine Renault Logan with a volume of 1.4 liters? To get a correct answer, you need to contact the factory instruction manual. Requirements say that:

• motors of all types, except 1.9 CDI - 5W40;
• diesel units with installed summer filter catalytic type - 5W30;
• gasoline and gas motors - 5W30;
• it is allowed to use a semi-synthetic basis, but only for diesel options - 10W40.

The above information is enough for the owner to determine which type of lubricant to use. In case of difficulty, the owner always has the opportunity to receive qualified assistance from sellers - auto-shop consultants, car market.

When buying oils, always pay attention to the presence of basic protective elements on the plastic canister, bar code, detailed description of the manufacturer.

How much can oil in Renault Logan?

Experienced car owners are always focused on the eye, the instruction is not a decree for them. In order not to harm the car engine, it is recommended to contact regulatory document. In this case, this is an instruction manual technical means. The rules established:

• for a power unit with a volume of 1.6 liters - filling capacity should not exceed 4.80 l;
• for a motor with a 1.4 liter volume - 3.35 liters.

Moreover, the data is indicated in the first case for the 16 valve mechanism, in the second - for 8. The manufacturer strongly recommends using ELF EVOLUTION Motor Oil with SXR Series with Synthetic Base.

Exceeding or disconnecting it leads to negative consequences in the form of overhaul Power unit.

It is necessary to take into account such a moment as the car mileage. If we are talking about soon repairs, including capital, then the use of mineral or semi-synthetic foundations is allowed. True, on the pre-category, not earlier. As the masters say that in the last month of operation, the motor will no longer hurt.

Admit technical condition Car to this - a sign of bad care from the owner. In most cases, such situations are regarded as an exception than the rule. To increase the life of the car or significantly reduce it, it is recommended to conduct technical inspection And refuel quality, original oil.

Best Oil for car Renault. Logan has always been considered that recommended by the factory producing this model. In all RENAULT service centers, when conducting regulations By replacing the engine lubricating fluid, the oil of the French brand ELF is poured. In rare cases, it may be proposed total oilwhich is produced by the same factory as ELF. They have even identical containers for retail sale.

Of course, the owner may not agree with the butlas recommended by the plant and act at its discretion. Here are the most common reasons for this:

1. As a rule, the search for better oil occurs at the end of the warranty period, and caused by a frank desire to perform simple procedure yourself, and not pay for the services for the replacement of motor oil on the official service;
2. For independent purchase original oil You can easily purchase falsification, so lubricant is selected with more reliable protection against fakes;
3. The desire to save money on the purchase of oils and, as a result, the choice of brands with a more affordable cost. This reason is the most common models for owners with an earlier year of release;
4. Tips of friends, acquaintances or colleagues on work using other, better quality in their cars, oil.

Renault concern has been developed for admission standards for the quality of oils used in cars. According to API classification, oil characteristics must match the SL, SM and SN classes. In addition, we should consider ash content, the presence of the necessary additives, etc. Any engine oil corresponding to the requirements and temperature regime (the lower the temperature below ambientThe lower the oil viscosity must be used to lubricate the RENAULT LOGAN engine. Making a sample of motor oils for our rating, we took into account not only the above requirements. The great impact on the decision of the decision was the reviews of owners who focus on Reno Logan oils of other manufacturers, the recommendations of motorists who are confronted in their work with the repair of engines of this brand and the popularity of the brand in the environment of car enthusiasts.

Best synthetic oil

This category lubricants most corresponds to modern car engines. Lower susceptibility to work at high temperatures and the preservation of lubricating properties and a given yield strength in frost, allows you to smoothly ensure the lubricant of the friction pairs in the motor, even during peak loads. For Renault Logan cars, especially with low mileage, it should be poured exclusively to the synthetics.

5 LUKOIL LUXE SYNTHETIC 5W-30

Best price in category
Country Russia
The average price: 1 240 rubles.
Rating (2019): 4.2

Domestic oil not only has excellent properties, but also received the RENAULT RN 0700 tolerance, and can be used in the respective Renault Logan motors. Oil is ready to provide engine reliable protection in heavy operating conditions. The engine perfectly washes and prevents the formation of sludge sediments, suppresses oxidative processes at high temperature, can increase engine power.

In his reviews, car owners fueling Lukoil Luxe Synthetic note the noise reduction during the operation of the motor, fuel savings, the lack of influence of strong frosts to start the engine. Laser notches, polymer sticker and technological features The caps on the canister give reliable protection and completely impede the emergence of a falsified product in the market.

4 Wolf Vitaltech 5W40

No fakes on the market. Stable viscosity characteristics
Country: Belgium
Average price: 1 762 rub.
Rating (2019): 4.5

Based on lubrication lie basic oils top quality and set of modern additives last generation. As a result, Wolf VitalTech has excellent fluidity when low temperatures, good antioxidant indicators, increased service life. Motor oil obtained tolerance and recommendations of the manufacturer of Renault Logan, so it can be safely used not only in the engine with a volume of 1.6 liters, but also with more economical 1.4 liters. The increased viscosity of this oil is also ideal for wear motors.

Reviews characterize the product as high quality, the lowest prevalence in the domestic market is positively estimated, which is the best guarantee of the lack of fakes. The last statement is also considered to be a disadvantage of oil, because it is rarely found in automotive stores and in the markets.

3 BP Visco 5000 5W-40

Best Motor Protection from deposits
Country: England
Average price: 1 468 rub.
Rating (2019): 4.7

BP Visco is checked by time and meets all the requirements for oils for Renault Logan. A unique system of additives Clean Guard carefully cleans the engine from the previously formed sludge and varnishing plaque, does not give the products of combustion entering the oil, to settle on the surfaces of parts, significantly increasing the service life of the engine.

Those who floods this engine oil into the engine of their Renault Logan, mark the easy motor start-up even with very strong frost, the quietest operation of the unit, as well as a noticeable decrease in fuel consumption. In addition, the reviews indicate the possibility of year-round use of oil, the increased interval between replacements and the absence of changes in the characteristics by the end of the service life.

2 Motul 8100 Eco-Clean 5W-30

Reliable engine protection from wear
Country: France
Average price: 4 566 rub.
Rating (2019): 4.8

Ideal engine oil for modern engine Renault Logan. When moving to its use, the owners in the reviews mark the more quiet and soft engine operation, fuel savings. Oil does not have factory access to the application in Renault Logan, as it is in premium segment Motor oils and pour it into this car more than expensive. At the same time, oil parameters have full compliance with Renault requirements and there are many drivers who pour exactly Motul 8100 Eco-Clean into their Logan.

In responses, they note positive changes in the operation of the motor - it becomes more economical (noticed on gasoline engines With a volume of 1.6 liters), it works significantly quieter and more stable, and also carefully supports the internal purity of the unit at a very high level. The only drawback can be considered the high cost of the product.

1 ELF EVOLUTION 900 NF 5W40

This is the best oil that can be bolder to pour into renault engine Logan. It is available not only in all RENAULT service centers, but also presents from many sellers of cars. When buying via the Internet or in the retail network, you should be very careful not to purchase a fake. High quality lubricant and its big popularity in our country (ELF is poured not only in Renault Group cars, but also in many other cars, including domestic) caused that under the type of corporate product, fraudsters come to the consumer Surrogate, having little General with motor oil ELF. Evolution.

Motorist reviewers confirm good detergents, lubricant stability at high loads, low passes. The effect of fuel economy is also observed. The lack of effective protection against fakes is noted from the disadvantages.

Best semi-synthetic oil

Renault Logan Motor Design Allows you to use semi-synthetic oil Only with a significant wear of the engine (mileage of 400,000 km. and more). Synthetics cannot fully fill out an increased gap and provide high-quality lubrication of parts. This is especially true for motors with a volume of 1.6 liters. But in these cases, it is necessary to approach the choice, as it is not possible to use in Renault Logan any semi-synthetic.

3 TEXACO HAVOLINE EXTRA 10W-40

The most enduring lubricant
Country: USA
Average price: 1 449 rub.
Rating (2019): USA

Has a reno tolerance and perfect for renault motors Logan with intensive exploitation in difficult conditions. The basic components of oil and additives provide a stable viscosity, good protection against corrosion and from the formation of internal deposits.

Owners who have become pouring in Renault Logan Havoline Extra, celebrate almost complete aback, excellent detergents, compliance with engine oil quality more expensive and popular brands. Also in reviews noted the lack of falsification in the market. Of the disadvantages - in specialized outlets is not always available. But with the help of the Internet (for the accuracy of choice, it should be aware of the article) it can always be purchased in advance.

2 Castrol Magnatec 10W40

Best Engine Protection
Country: England (produced in Belgium)
The average price: 1 235 rubles.
Rating (2019): 4.6

The Intelligent Molecules additives group gives oil the ability to "cling" behind the rubbing surfaces and stay on the items even when disabled Engine. Thanks to this technology, when the motor is started, even in the frost, there is not a split of a second of the work of friction pairs without lubrication, which significantly increases the resource.

In his reviews, Renault Logan owners tell about the ability of oil to gently clear the engine from the accumulated sludge - it is enough to spend just a couple of replacements. The properties of motor oil when working on extreme loads allow you to save the engine from overheating. High temperature stability is an obstacle to the formation of sludge sediments. Also, the reviews are noted by the main disadvantage - the possibility of acquiring under the guise of a high-quality goods of cheap fake, which is capable of not only to disappoint consumer quality, but also harm the engine.

1 Liqui Moly Top Tec 4100 5W40

The most environmentally clean oil
Country: Germany
The average price: 3 110 rubles.
Rating (2019): 4.8

Pouring this oil in Renault Logan allows the manufacturer - the composition of the oils meets the requirements of Reno Rn 0700 / Rn 0710. The owners in their reviews point out the appearance of fuel economy, easy launch at minus temperatures. In models with a 1.6 liter engine. It is noticeable to increase the resource - free-free operation with mileage exceeding 500 thousand km. At the same time, the transition to this engine oil occurred after 200 thousand km.