Home Chassis Hyundai Solaris does not burn a check. Hyundai Solaris: Control lamps and indicators. Enabit light indicator

Chassis

Hyundai Solaris does not burn a check. Hyundai Solaris: Control lamps and indicators. Enabit light indicator

It often happens that on the instrument panel in the car equipped with electronically controlled, the emergency sensor light lights up. If the car started, continues to work, but at the same time the engine check was caught fire, this means that the inclusion occurred in emergency mode. Some models of modern machines (Audi, BMW, Mercedes-Benz, Porshe, VW) are equipped with a system that can exercise self-diagnosis, errors in the decrypted form go to the information panel. But drivers do not always manage to understand why the engine malfunction was caught fire.

To start the motor, the driver includes ignition. If the engine check is blinking, this should not cause concerns, since he will soon go out. But the burning signal, with the engine running, indicates violations in its work.

If you occur in the operation of the power unit, an error in the form of a coded signal is recorded in the control unit memory. In this case, the motor check is on the dashboard. If the AUTO does not provide for diagnostics in automatic mode, you need to connect a device to a special connector for scanning. The scanner reads the code and performs detailed decoding of the error.

In the process of electronics development, the Check Engine indicator has become a simple fault sensor into a signaling device with a set of functions. Modern engine check with blinking reports the following inconsistencies:

improper composition of fuel mixtures;
settings failures in the ignition system;
sensors failures.

His task also includes reporting problems not related to the power unit. To reveal the place of origin and nature of the breakdown, professional knowledge, experience, special devices and tools will be required from the masters.

Important: The electronic unit of the ECU gives the command to flashing the alarm, as a result of the detection of errors of varying degrees of complexity. Among them are issues of both serious and small. In order to conduct diagnostics, it is recommended to suspend the operation of the vehicle. Experienced car owners often independently determine the reason for the inclusion of the check, without waiting for a visit to a hundred.

Signs of basic faults and causes indicator signal appearance

If the engine lights up during the movement of the car after refueling at the gas station, the most likely reason is the inappropriate quality of the flooded gasoline. At the same time, the following symptoms are observed:

Reduced power.
Interruptions in the engine (stall).
Detonation as a result of incomplete combustion of fuel.

add a higher quality fuel to the tank;
dry gasoline, filled with recently, clean the fuel system.

If the check does not want to go out after the reason has been eliminated, it is required to remove the error recorded in the device's memory using a special computer program.

Checking the oil level and its status

In the following, the causes of the signal occurrence, are considered to be overheated by the motor, lowering the lubrication fluid level in the engine. It is recommended to check the engine temperature. In the absence of overheating, you need to check the volume and condition of the oil. After checking the level, it is necessary to attach the missing amount of lubricant. With a clean paper napkin, the quality and composition of engine oil is checked for the following criteria:

Color.
Consistency.
The presence of mechanical inclusions.
The smell of burning.

If everything is in order with the quality and amount of oil, the engine is started to eliminate unusual sounds, noise when working both in idle mode and under load.

When identifying non-standard noise effects of a working engine on the background of a burning check, it is recommended to send the car to the nearest service company. An independent movement of the car is not recommended, delivery is carried out using towing or other in a convenient way. Further operation can lead to serious breakdowns and expensive repair of the elements of the power unit.

Flashing Indicator and Engine Troy

When the check is simultaneously flashing and troit engine, it is necessary to examine the ignition system elements:

wiring;
coil.

The hardware effect occurs when only three combustion cameras work instead of all four. The engine begins to told in the absence of injection of the fuel-air mixture into one cylinder.

Developed and contaminated spark plugs also cause the check Engine signaling device. To do not think long, how to remove the engine check, you just need to clean or completely replace outdated candles to a new set.

Checking the ignition coil comes down to measuring resistance on terminals and testing for the ability to create a spark of blue.

What to do if the engine check is caught off due to failures in the fuel supply system

With violations associated with the flow of fuel in the cylinder, it is recommended to check the state of spraying nozzles. Their holes must be cleaned, rinse, if necessary, to completely replace on new devices.

Reduced pressure in the fuel system caused by faults:

Basonasosa (in carburetor, injection engines).
Fuel filter
Pump TNVD (in diesel).

If the ignition of the check is caused by the failure of the catalytic neutralizer, the drivers simply remove it from the exhaust system, and then turn off the corresponding sensor (oxygen).

How to Reset Check Engine Error

If you have critical errors in the engine operation, the information is recorded in the memory of the ECU and is not deleted independently even after eliminating the defect. At the same time, the check continues to glow. To reset the recorded error with your own hands, experienced car owners perform the following operations:

heat engine to operating temperatures;
dismiss the terminal on the battery for a while (from 5 to 15 minutes);
restore the connection to the terminal;
insert and rotate the ignition key, not reaching the launch (while all the indicators on the instruments are lit);
wait for one minute;
turn the key in the opposite direction.

Most often, such actions lead to the desired result, the error code disappears from the memory of the ECU block. The check stops glowing after turning on and operating the engine at idle mode for three minutes.

If the disconnection method of the terminal did not work, the alarm continues to flash, the error from the memory of the control device is removed using special computer programs through the Diagnostic OBD plug connector.

The control unit can also cause the CHECK signal to turn on, if the individual elements of the ECU are partially or completely fail.

If the Check Engine indicator light lights up on the dashboard of your car (or simply burns the "check"), you should be at least tolerance. The reasons for this can be the most diverse - from a loosely twisted lid of the gas tank to serious problems with the engine.

What indicates the Check Engine indicator

The name of the Check Engine indicator is literally translated as "Check the engine". However, the engine during sunbathing or flashing the bulb can be completely without anything. The light indicator may indicate problems in the fuel supply system, failure of individual ignition elements, etc.

Sometimes it can be a very small problem - for example, an unloaded gas tank cover or a catalyst malfunction. Nevertheless, the indicator signals cannot be ignored in any way, as this may turn into serious problems.

Sometimes the reason for the lighting of the indicator may be poor fuel quality. So do not be surprised if, after refueling on an unfamiliar gas station, you will see a flashing light bulb Check Engine.

Typically, the indicator is located on the car dashboard under the engine speed pointer. It is indicated by a schematic engine or a rectangle with the inscription Check Engine or just Check. In some cases, inspiration is shown a zip sign.

Is it possible to continue moving at a burning light bulb

Brake pads were worn out, the time came the next one, the speed was incorrectly shown, low-quality fuel is used, the on-board voltage dropped - all this can be a reason for sunburning the Check indicator. First of all, you should check the motor. If the cause of the signal is turned on are engine malfunctions, continue to move dangerous.

The problem is exacerbated by the fact that it is impossible to determine the malfunction of the modern engine in the smell or color. You should contact professionals that, using the scanner, will identify a malfunction if, of course, it is available.

Burning Light Check may indicate different breakdowns - it is better not to ignore it

Therefore, if after re-starting the car, the light bulb did not go out, you can move on it only to the nearest car service. There will be a comprehensive diagnostics of the engine and its systems.

The operation of the car with a burning Check Engine icon leads to increased fuel consumption, unstable operation of the motor, reduce the traction characteristics of the car. Moreover, in this case, the car owner can lose the car repair guarantees.

Why light bulb caught fire and how to fix it

The main situations in which the indicator lights up, and the recommended vehicles of the motorist actions:

If Check Engine when starting the car lights up and immediately goes out, no engine damage. The cause of sunbathing is most likely harmless - the loss of the fuel tank cover or its failure. It is enough to wrap it tightly and check whether the warning disappeared.
If the indicator caught fire during the movement, you should stop and check the wires. You may find a hood-free cable or an open terminal of the battery. This applies to the entire hinge - wires, hoses, etc.
If the light flashes while driving, you should stop and check the sounds published by the engine, pay attention to the oil level, inspect the lateral parts of the motor. If visually explicit violations are not detected, it is recommended to get to the nearest car service and conduct diagnostics.
If the engine works normally, and Check light flashes, most likely, the ignition failure occurred. You should check the candles and the coil, pay attention to the quality of fuel. To do this, it is better to contact the nearest autodiagnostic center.
If the indicator is on constantly, it is necessary to stop, unscrew the candles and check the gap. Clauses that exceed 1.3 may be a reason for sunbathing light bulb.
In addition, when burning "check" is usually checked. In any car service there are special testers that allow you to determine the wiring isolation wear.
The faulty fuel pump may become the cause of the lighting of the light bulb. You should stop and listen to the sounds published by the fuel pump. Normal is considered smooth buzz without clicks and pauses. If extraneous sounds appear, the pump should be dismantled, washed from the inside and clean the filter.
The cooling fluid temperature may indicate seriously engine malfunctions. If it is above 85-90 degrees, and when moving, Check Engine lights up, the engine is definitely faulty. In this case, it is desirable to call a tow truck or at a low speed to get to the nearest car service.

We have already noted that Check lights up each time the engine starts yellow or orange. This is normal if the flashing lasts no more than 3-4 seconds and stops along with the flashing of other dashboard indicators. Otherwise, the above-recommended action should be performed.

Video: Check sensor lights up

https://www.youtube.com/embed/uqdkfkx4mle

Table: Causes of lighting indicator Check Engine and proposed actions

When and in what cases burn "Check"	Possible reasons	Suggested actions
When driving, during acceleration	Sharp acceleration, faulty air filter	Replace the filter, accelerate smasher
When flashing the indicator troit engine	Fuel in one of the cylinders is not completely combined, gasoline or tramples in the exhaust pipe, or immediately falls into the catalyst	Replace candles, check the coil and armor, check marks timing
After refueling	Low quality fuel	Change gas station
When the ignition is turned on	Normal car reaction	Do not do anything
After washing the car, the engine, after the rain	Water CHECK ENGINE hit	Process WD40, dry, clean the contacts
On a cold engine	Detonation sensor is defective	Replace
On hot engine	Faulty camshaft sensor	Replace
At high speed	Skipping ignition coils or crankshaft sensor malfunction	Replace the coil or sensor
At idle	Throttle Sensor Fault	Replace
After replacing candles	"Poor" combustible mixture	Change the octane number of gasoline to a higher
After replacing the air filter	It became more air, the composition of the exhaust has changed, the lambda probe reacted	Load the engine, run again
After replacing the remnal distribution mechanism	Scumped terminal from a sensor, most likely, air hose	Check terminals
After installing gas equipment	The emulation of the benzoformuska is incorrect	Tune
After installing the alarm	Only one power line is connected to the turbo-timer, the temperature sensor, the brake pedal and the mass flow sensor	Reset Check Engine, connect both lines
After replacing the fuel filter	Installed filter with small pressure	Replace filter
With the simultaneous increase in fuel consumption	Overweight riding, ache oxygen or poor-quality fuel	Refuel high-quality fuel, give the car to relax
With long lifting	Timing belt wear, sensor malfunction	Check and replace
After replacing the ignition module	Connecting module problems	Remove and apply a plus terminal with a battery
For minus temperature	Throttle position sensor malfunction or disconnecting its chips	Replace device or install chip in place
Pressing the accelerator pedal	Wrought air filter	Clean or replace the filter

Reset or reset the check indicator

In most cases, as the table shows, Check lights up when the sensor fails or changes the operating conditions of the car. However, even after diagnosing and eliminating a malfunction, the light bulb sometimes continues to burn.

The fact is that the "trace" of errors remains in the memory of the computer. In this case, you should "reset" or "reset" the indicator readings. This can be easily done independently by performing a number of simple operations:

The sensor is reset, and the Check light is no longer lit. If this did not happen, contact the service center.

The CHECK ENGINE indicator lighting on the dashboard almost always requires an immediate stop of the car. The use of the recommendations given in the article will help you avoid the complex expensive engine repair. Good luck on the roads!

.
Asks: Smirnov Kirill.
Essence of the question: How to reset the "check"?

Hello! I have Hyundai Solaris, and "Check" is constantly lighting up! I have already traveled to the maintenance station and found out what the problem is. The first time they dropped it to me, and now she appeared again, while the behavior of the car did not change. Tell me, please, how can I drop it yourself, because I do not want to pay for it again.

If the check lights up when the engine is started, it is not worth worrying. But if the check is burning when the engine has already gotten, then you need to know the cause of the error.

Diagnosis and removal of emerging errors on Hyundai Solaris may need a vehicle owner in various situations when there is no desire to do this work in a certified service center.

Do this job is not difficult, the main thing is to know that you can delete yourself errors related to the first level , that is, those who are not recorded in memory of the ECU, which are not significantly affecting the work of the car and its devices. Because it will be able to remove such a special dealer device (scanner - approx.), One of these errors includes a car airbag error.

When errors are deleted independently?

Among all important problems on Höndai Solaris, some can be independently discharged after conducting one or another repair.

For example, error codes with 301 by 304 , speaking sparks in one of the cylinders (the last digit of error belongs specifically to the cylinder - approx.).

If the error signals the pass in the cylinder, first of all look at the state of the spark plug. In the photo candle, the culprnor of this error.

Accordingly, when these skips are detected, the computer will give a signal, in the form of a burning "check", which will not be able to remove not erasing the code, nor the discharge of the terminal with the battery.

The mistake is removed completely, only the replacement of the non-working candles to the new one, after which the error will disappear by itself.

Independent reset check on Hyundai Solaris

Reset the errors on their own on Hyundai Solaris is possible thanks to the OBD-II protocol and the presence of a special adapter with a diagnostic device, be it a smartphone or computer that supports Bluetooth wireless technology.

In order to test errors by car, perform the following actions:

Standard Check and Reset Errors SCAN Master

The process of diagnosing and reset errors without OBD-II

On Hyundai Solaris, you can diagnose and delete errors, even having no additional devices at hand.

Diagnostics (this method does not work)

The method described below runs throughout the Internet. We checked on our editorial car. He does not work. Do not delete the way, as some owners may think that it works.

Discover video:

Delete errors

In order to remove the error, it is necessary to do the entire above-mentioned work of work with 1 to 5 item, and not turning off the ignition click on "gas" again.
After that, turn off and turn on the ignition, we start the engine.
If the work has been done correctly, the error must be removed.

As you could see for yourself, nothing complicated in removing an error on Hyundai Solaris yourself, no.

The video burns the check and Hyundai Solaris stalls

When you turn the ignition key to the ON position, it is checked for the health of all control lamps (do not start the engine). Any lamp that will not light up requires checking from an authorized Hyundai dealer.

After starting the engine, make sure that all the control lamps went out. If any of them continues to burn, it indicates the occurrence of a situation that requires attention. When unlocking the parking brake, the parking brake test lamp should go out.

Low fuel control lamp will continue to burn if the fuel supply is insufficient.

Eco (eco-indicator, if available) (automatic transmission)

Eco-indicator is a system that allows you to control the vehicle in economy mode.

The indicator is displayed in economical fuel spending, which allows to increase fuel efficiency.

Eco-indicator (green) lights up if in ECO ON mode fuel is consumed effectively.
Displaying an eco indicator can be disabled by pressing the Trip button. The on and off of the eco-mode is described on the previous page.
Fuel efficiency depends on driving style and road conditions.
This function does not work in such uncatching criteria for economical driving conditions, like P (parking), N (neutral) or R reverse.
If the display shows the current fuel consumption, the ECO indicator turns off.

CAUTION

Do not watch the indicator while driving. It distracts from driving a car and can cause a crash that leads to serious injury.

Control lamp of the airbag system (if available)

This warning lamp lights up for about 6 seconds each time after turning the ignition key to the ON position.

This lamp also lights up in case of malfunction in the airbag system. If this lamp does not light up or continues to burn after 6 seconds after turning the ignition key to ON or start the engine, or if it lights up while moving the car, you need to contact an authorized Hyundai dealer to check the condition of the airbag system.

Non-unsigned security belts (if available)

As a reminder, the driver and a passenger, the warning of the seat belt signal will shine within 6 seconds each time after turning the ignition key to the ON position, regardless of whether the belts are fastened or not.

For more information, refer to the Safety Belts in Chapter 3.

Insufficient pressure control lamp of motor oil

1. Observing caution, rebuild to the edge of the carriageway and stop the car.
2. When the engine is stopped, check the oil level. If the oil level is below the norm, the oil becomes in accordance with the requirements.

If this test lamp continues to burn after adding an oil into the engine, or if there are no oils, contact an authorized dealer of Hyundai.

ATTENTION

If you do not stop the engine immediately after turning on the insufficient pressure of the engine oil, the engine can be seriously damaged.

ATTENTION

If during operation of the engine, the dysfunction lamp of the insufficient pressure of the engine oil is lit, serious engine damage is possible. This lamp lights up if the pressure in the lubrication system falls below the norm. In a normal situation, it lights up when the ignition is turned on and then goes out after starting the engine. If a lamp warning about low oil pressure is on during the engine operation, this indicates a serious malfunction.

In such a situation, you should stop the car as soon as you will have a safe opportunity, stop the engine and check the oil level. If the oil level in the engine is below the norm, make the oil to the norm and start the engine again.

If the lamp continues to burn while the engine is running, stop it immediately. In any case, if the lamp of the insufficient pressure of the engine oil is lit during the engine operation, before running the engine again, it is necessary to contact the authorized Hyundai dealer to check the condition of the car.

Control lamp of parking brake and insufficient brake fluid level

This lamp lights up if the parking brake is in the on state, and the key in the ignition lock is in the START or ON position. This lamp should turn off when unlocking the parking brake when the engine is running.

Preventing the insufficient level of brake fluid

The glow of this control lamp indicates an insufficient fluid level in the brake system tank.

If this test lamp is lit:

1. Observing caution, roll up at the nearest safe place and stop the car.
2. When the engine is stopped, immediately check the level of the brake fluid and decrease it in accordance with the requirements.
After that, check all the elements of the brake system for leaks.
3. It is not allowed to continue the movement of the car if leaks were detected if the test lamp continues to burn, or if the brake system work differs from the norm. The car should be towed to check the brake system and perform the necessary repair work by an authorized dealer of Hyundai.

This car is equipped with a dual brake system made in a diagonal scheme.

This means that even in the event of a failure of one highway, the brakes on two wheels of the car will be in working condition. In such a situation, a larger course of brake pedal will be needed to stop the car and more effort on it.

In addition, the brake path of the car, which only has a part of the brake system, will be more normal. If the brake fails during the car movement, switch to a lower transmission for engine braking and stop the car as soon as a safe opportunity has an opportunity for this.

To check the functioning of the control lamp on the parking brake and the insufficient level of the brake fluid, make sure that it burns when the ignition key turns to the ON position.

CAUTION

Driving a car while a warning lamp is burning, dangerous. If the brake system control lamp continues to burn, immediately refer to the authorized Hyundai dealer to check the brake system and repair.

Control lamp of anti-lock brake system (ABS) (if available)

This lamp lights up when the ignition key turns to the ON position and goes out after about 3 seconds if the system is properly.

If this lamp continues to burn after turning on the ignition, lights up while moving, or does not light up after turning on the ignition, this indicates a possible malfunction of the ABS system.

In such a situation, you need to contact the authorized Hyundai dealer as soon as possible to check the condition of the car.

The brake system of the car will continue to function, but without the support of the anti-lock system.

Control lamp electronic brake force distribution system (EBD)

If during the movement at the same time two control lamps light up, the car is faulty and ABS system, and the EBD system.

In this case, the ABS system and the main brake system can operate in abnormal mode. It is necessary to contact an authorized Hyundai dealer as soon as possible to check the condition of the car.

CAUTION

If the control lamp of the ABS system and the brake lamp of the brake system are lightning and continue to burn, this means that the car braking system will not work normally with sharp braking. In this case, movement should be avoided at high speed and sharp braking. As soon as possible, contact your authorized Hyundai dealer to check the condition of the car.

FOR YOUR INFORMATION

If the ABS or EBD reference lamp is on and remains and remains, this may indicate a speedometer or odometer / odometer of the trip. In such a situation, you need to contact the authorized Hyundai dealer as soon as possible to check the condition of the car.

Indicator of the Electronic Stability Stabilization System (ESP) (if available)

This indicator lights up when the ignition key turns to the ON position and should go out for about 3 seconds. When the ESP system is turned on, it controls the conditions of the car. If the conditions are normal, the indicator of this system does not burn. When leaving the slippery road or with a decrease in tire clutch with an expensive ESP system starts working.

At the same time, its indicator begins to flash, informing about the operation of this system.

But in the event of a malfunction of the ESP system, the indicator lights up and does not turn off. In such a situation, you need to contact the authorized Hyundai dealer to check the car.

ESP System Disconnection Indicator (if available)

This indicator lights up when the ignition key turns to the ON position and should go out for about 3 seconds. To disable the ESP system, press the corresponding button. The indicator will light up, indicating the disconnection of this system. If this lamp is lit when the ESP system is turned on, the system may have a malfunction.

Indicators of rotation indicators

Flashing green arrows on the dashboard displays the direction that shows the turn signs. If such an arrow lights up, but does not blink; Flashing more often than usual or does not light up at all, it indicates a malfunction of the rotation indicators system. To eliminate it, contact an authorized dealer.

Light light indicator

This indicator lights up when the far beam is turned on, or with short-range light, using the rotation indicators control knob.

Enabit light indicator

Fog light indicator (if available)

The inclusion indicator of the rear fog lamps (if available)

Reminder signal on the inclusion of rear fog lamps (if available)

The reminder signal will sound if the rear fog lights are included in the situation when the driver's door is open when stopped.

The indicator of the selected range (if available)

Mechanical Transmission Shift Indicator (if available)

This indicator reports to the driver, which transmission is desirable to choose, which allows you to save fuel.

For example:

: Indicates that it is desirable to switch to the 3rd transmission (currently included 2nd transmission).
: Indicates that it is desirable to switch to the 3rd transmission (the 4th transmission is currently included).

FOR YOUR INFORMATION

When the system does not work properly, the indicator is directed up / down the arrow and the transmission number is not displayed.
When choosing an ECO-OFF mode on the route computer, the mechanical gear shift indicator will not be displayed.

Rechargeable Battery Charging Control Lamp

This control lamp indicates the presence of a malfunction of either the generator, or the battery charging system.

If it lights up during the car movement:

1. Move the car to the nearest safe place.
2. When the engine is stopped, check the tension of the generator drive belt and the absence of its rupture.
3. If the belt tension is normal, the fault is present somewhere in the battery charging system. Contact your authorized Hyundai dealer to eliminate the malfunction as soon as possible.

Low fuel control lamp

This lamp indicates that the car's fuel tank is almost empty. In such a situation, you need to quickly fuel the car with fuel. Continuing the movement with a burning lamp warning about a low level of fuel in the tank, or in the case when the fuel level indicator arrow is below the "E" mark, can lead to a pass of outbreaks in the engine cylinders and damage to the catalytic neutralizer.

Control lamp of insufficient fluid level in a glasswater tank (if available)

The glow of this control lamp indicates that the washer tank is almost empty. As soon as possible fill the tank.

Engine malfunction control lamp

This control lamp is a part of the engine control system, which controls the state of various elements of the exhaust gas toxicity control system. If this lamp lights up during the car movement, this indicates the possible presence of a malfunction somewhere in this system.

In addition, this lamp lights up after turning the ignition key to ON, and then goes out after a few seconds after the engine is started. If it lights up during the movement of the car, or does not light up after turning the ignition key to the ON position, you need to contact the nearest authorized Hyundai dealer to verify the system status.

In the general case, the car can move, but it is necessary to immediately contact the authorized Hyundai dealer to check the status of the system.

ATTENTION

Long movement with a burning control lamp of a malfunction of the system for monitoring the exhaust gas toxicity can lead to damage to the elements of this system, which will affect the driving characteristics of the car and / or on the consumption of fuel.

ATTENTION

If the malfunction indicator of the exhaust gas toxicity control system lights up, it is possible to damage the catalytic neutralizer, which can lead to loss of engine power.

As soon as possible, check the engine control system from an authorized Hyundai dealer.

Engine coolant temperature control lamp (if available)

The control lamp lights up when the coolant temperature of the engine exceeds 125 ± 2.5 ° C (257 ± 4.5 ° F).

Invalid the continuation of the trip with the superheated engine. If the vehicle engine overheated, see "If the engine is overheated" in section 6.

FOR YOUR INFORMATION

If the engine coolant temperature control lamp is burning, it indicates overheating, which can cause engine damage.

Examination lamp opening trunk lid / luggage door

This test lamp lights up if the trunk lid / luggage door cover is not closed, with any key position in the ignition lock.

Control lamp alarm for unclosed door

This test lamp lights up if the door is closed loosely, at any position of the key in the ignition lock.

Door opening indicator (if available)

The indicator shows which door is open.

Immobilizer work indicator (if available)

This lamp lights up when the key with the transmitter of the immobilizer system is inserted into the ignition lock and is translated to the ON position to start the engine.

At this point you can run the engine. After starting the lamp goes out.

If this lamp flashes while finding the ignition key in the ON position before starting the engine, you need to contact an authorized Hyundai dealer to check the system.

With electronic key system

If in a car equipped with an electronic key, one of the following situations arises, the immobilizer warning lamp lights up, starts flashing or goes out.

When the electronic key is in the vehicle, if the start / stop button is activated by ACC or ON modes, the indicator is displayed. If there is no electronic key in the car, when you press the start / stop button, the control lamp will flash within a few minutes, recalling that you will not be able to start the engine.
If after 2 seconds after turning the ignition key to the ON position the control lamp goes out, this may indicate the system malfunction. In this case, contact your Hyundai authorized dealer for checking the car.

You will need: all the tools needed to withdraw the rear cladding of the left threshold of the floor and the trunk cladding, as well as the end head "on 10". 1. Remove the front and rear cladding of the left ...

Dropping pressure in the supply system of gasoline engines
Remember that gasoline is highly flammable liquid! When working with power system components, observe all the received fire safety measures. Do not smoke! Do not close to the month ...

Camshaft. The axis of the camshaft
1. Remove the axis of a bruise and rocker (p. 2.8). 2. Remove the slave pulley of the camshaft (p. 2.6.14-2.6.16). 3. Remove the camshaft from the cylinder head towards the flywheel. Shaft thoroughly ...

Car: Höndai Solaris. Asks

: Smirnov Kirill. Essence of the question: How to reset the "check"?

Diagnosis and removal of emerging errors on Hyundai Solaris may need a vehicle owner in various situations when there is no desire to do this work in a certified service center.