The replacement of antifreeze on Daewoo Matiz is not difficult, however, taking into account the specifics of the assembly has certain differences from the total procedure. The entire procedure of the car owner can produce independently in the presence of technical skills and knowledge.
Antifreeze replacement interval
Replacing antifreeze B. Daewoo Matiz It is produced every 4 years or after a run of 80 thousand km. The basic values \u200b\u200band imply the absence of other factors affecting the efficiency of the coolant.
If antifreeze discolored or acquired a brown, reddish or black shade, it should be replaced as quickly as possible. Color change speaks of low product quality, lack of necessary additives and negative effects of coolant on the entire system.
In order to avoid failure of more expensive nodes, the antifreeze should be purchased from proven official dealers. Specialists pay attention to the following brands suitable for Daewoo Matiz:
- 1998-2002 Year of release - Antifreeze category G12, Motul Ultra, Castrol LF, Glaaself, AWM, Lukoil Ultra are suitable;
- 2003-09 - G12 +, Lukoil Ultra, G-Energy, Havoline, AWM, Freecor will be suitable;
- machines Daewoo Matiz C 2010 require a category G12 ++, the antifreeze of Glysantin G 40, Freecor DSC, VAG, Frostschutzmittel A. is suitable.
The amount of coolant depends on the volume of the engine: 0.8 liters will require 3.8 liters of antifreeze, 4.2 liters on a single-liter motor. If concentrate is purchased, then the volume is calculated taking into account the addition of distilled water.
How to check the level in Daewoo Matiz?
The cooling fluid level is checked along the expansion tank under the hood of the car. Max tag was tinted in black, the MIN label serves the weld of the expansion tank itself.
To check the level of antifreeze, no additional manipulations are required, the translucent body allows you to evaluate the volume and without unscrewing the lid. However, in addition to the amount of coolant, its color is also monitored, as well as the presence of precipitate, foam, contaminants and other factors indicating the need to replace antifreeze on DEU Matiz.
To correctly check the level and condition of antifreeze, the engine of the machine is devastating and give it to cool. Experts pay attention to the fact that the coolant, especially with the newly operated engine, is under pressure. A sharp opening of the lid can cause splashes and to enter the toxic fluid on hand and face.
Opening the lid should be carefully, only when the motor has cooled and, if possible in gloves. Some experts also recommend to shoot minus from the battery as an additional precautionary measure.
How to replace?
The replacement of antifreeze in Daewoo Matiz is made taking into account the three main stages of the process - draining the old coolant, flushing the system and the fill of the new solution.
Separately pay attention to the need for washing. After draining in the system, a certain number of old coolant remains. If it turned out to be a poor-quality or car owner acquired another brand of antifreeze - it should be thoroughly rinsed remnants.
When washing the cooling system, Daewoo Matiz is not recommended to use special flushing fluids. In the absence of drain cranes, such mixtures will also be asced in the system, which will require additional procedures for the cleaning. Taking into account this factor, the old antifreeze is washed with distilled water.
Preparation
To replace antifreeze in Daewoo Matiz, the following will be required equipment:
- pliers, keys and screwdrivers for removing fixtures, passatia;
- gloves, clean rag, funnel for fill;
- capacity for draining waste liquid and washing water, usually use a pelvis and an additional container with a volume of 5 liters;
- consumables - new antifreeze, distilled water from 10 liters for mixing with a concentrate and washing system.
The car pargets in the same place. The presence of the pit is not necessarily, especially if it is supposed to use a pelvis. In preparation, antifreeze toxicity is taken into account and measures are used so that there are no animals and children nearby, and so that the liquid does not get into the soil.
The question of how to merge antifreeze with Daewoo Matiz is solved by a general action procedure. However, the specifics of the assembly of this model requires additional operations.
Step-by-step instruction
The phased process of replacing antifreeze on Daewoo Matiz implies the following procedure:
- the engine is allowed to cool, as an additional precautions from the battery, minus is removed, in the future it is returned when warming up and shutdown;
- dismantling air filter and the housing - for this weaken the clamp on the nozzle and unscrew the holding the bolts, also remove the connector from the sensor;
- on the nozzle at the bottom of the radiator, the mustache clamps are compressed, substitute the container to drain and remove the hose;
- at the exit of the expansion tank, the cap is unscrewed, which ensures depressurization and faster drain;
- remove the radiator - for this, we unscrew the hold on its attachments and remove the nozzle from the top;
- replacing antifreeze on DEU Matiz without removing the radiator is allowed, however, taking into account the absence of drain cranes requires additional procedures for flushing and does not guarantee the full release of the system from the waste coolant;
- the radiator removed was washed with distilled water;
- remove the expansion tank, which is also washed in a separate order;
- the expansion tank and the radiator return to the place, connecting and tightly fed all the available connections;
- the air filter is returned to the place, the system is brought into the source view, after which distilled water is poured into the bulk neck;
- the engine is raised and allowed to work 15-20 minutes, after which it is devoured and allowed to cool;
- the air filter is rented again, distilled water drained from the system, after washing the radiator and the expansion tank, it must be relatively clean;
- restoring the system, a new antifreeze is poured into the expansion tank, periodically living low radiator hose to avoid education aerial traffic;
- the coolant is poured to the MAX level, the plug is spinning, the engine warms for 15 minutes.
If after the motor operation, the level of antifreeze fell - it is aging up to the upper limit. A few days after the replacement, the level and color of the fluid is checked, if necessary, it is fused or change to a new one. The constant drop in the coolant level indicates a leakage - connections are spinning loosely or there are nodes requiring replacement.
For a long time not published daewoo Matiz Car Repair Articles (Daewoo Matiz).... and this is not order! It's time to remember the baby again. Moreover, I feel warm feelings for this car))). This time it will be discussed about replacing the coolant! I can immediately say that in work by replacing the coolant in the car Daewoo Matiz There is nothing difficult. Everything is quite simple and accessible. Of course, if you know what to do. Therefore, before taking a tool in your hands and climb under the hood of your iron friend, I recommend reading this text to the end))). America, I will not open for you, but I still hope that the article will be useful for you!
And start most likely from the list of reasons why it is necessary to change the coolant: regulations (it is recommended to change the coolant every 80,000 km of run or after 4 years of operation), the cooling oil got into the system, the cooling fluid has changed the color (it became significantly light, soaked, turned into a red-haired mixture with a sandy sediment). The latter reason is directly related to the compliance with the regulations for replacing the coolant and the use of poor-quality products. And often it happens that I forgot to replace the cooling fluid on time or flooded the "local" spill to the Tosol system and later discovered in expansion tank Rusty liquid with sand-sediment on the walls and bottom of the tank. And this problem is quite serious. Because, "such" liquid is capable of very short term Instruct not only the pump, but also cooling radiators and the heating of your car. And so, in the Matyze, the constructors did not provide drain plugs on the engine block and the cooling radiator, drain cool
So, we go further ... After they have decided to independently replace the coolant in your favorite matze, it is necessary to determine the "quality and number" of this fluid itself. That is, answer the most common questions - " How many cooling fluid liters enters the Daewoo Matiz cooling system?", "What should be poured into Matiz - Tosol or antifreeze?", "What (color, manufacturer, classification) antifreeze is better to fill in Daewoo Matiz? "
According to the first question - in the Daewoo Matiz car cooling system (Daewoo Matiz) with an engine 0.8u includes 3.8 liters of coolant, and in Matiz with engine 1.0 - 4.2 liters.
On the second issue. I know that many again and again will breed that there is no difference between Tosol and antifreeze, except the name. And in Matiz, you can safely pour Tosol and do not worry yourself. But I do not agree with that. I consider the right answer - only antifreeze. And now there is no time to remember the history of creating the appearance of antifreeze and antifreeze, to understand what they differ from each other and list the additives and the components of the other. To do this, it is better to create a separate topic. And now my answer is better to pour antifreeze, at least due to the fact that the chances to buy a "linden" Tosol is much larger than poor quality antifreeze.
And naturally, the answer to the third question. In Daewoo Matiz (Daewoo Matiz), it is recommended to flood antifreeze based on ethylene glycol, class G12, red (orange) color. By the manufacturer, it is difficult to advise something, you do not want to allocate someone. Listing famous firms, such as Hepu, Shell Zone, Liquim Moth, etc., I will not surprise anyone. I can only advise, when buying any antifreeze, do not be shy to ask the seller the quality certificate for this product. As they say, trust, but check.
As a result. To replace the coolant on the Daewoo Matiz, it is necessary to buy - 2 liters of antifreeze and 2 liters of distilled water. If the cooling system is contaminated (black or brown liquid, sand sediment) or you decided to pour the cooling fluid of another color, then in this case you have to rinse the system. And for this you will have to buy 10 liters of distilled water. Why 10 liters? Because, usually this amount is enough when changing the "colors" of antifreeze or flushing is not strongly contaminated cooling system. Use no water or flushing fluid to wash the system is not desirable. Why not desirable? I will answer, repeating and run ahead. In the engine and radiator of the cooling of the car, Daewoo Matiz are not provided with drain plugs, which greatly complicates the full drainage of antifreeze. And even removing the cooling radiator (about it below), you will not be able to completely drain the liquid from the cooling system. Although removing the expansion bar, even though in the nozzles, still in the system will remain with the floor of the liquid, and if this liquid is a simple distilled water (in the engine block and the stove radiator). Verified. Therefore, the system is better to rinse with distilled water, one, two, three times, until the moment, until the system starts to go out pure water. Using washing fluid, You are 100% double the number of washing cycles (except for dirt, you still have to rinse the system from the specialty liquid), plus the likelihood remains that flushing fluid, though in a small amount remains in the system. And this, it is unlikely, will positively affect the service life of antifreeze and the parts of the cooling system. Therefore, I believe that it is better to wash the system with distilled water and to the choice, and the deadlines for replacing antifreeze is very serious.
On the tool and place of work. Lifter or observation pit to replace antifreeze on daewoo car Matiz (Daewoo Matiz) need not. Enough, it will be easy to find a flat platform. With tools Also, everything is simple: a wide capacity for the drain of the old coolant (volume of at least 5 liters), flat and cross screwdrivers, passatia, the end key to 10.
After buying antifreeze and preparation of the instrument, go to the main thing - to replace the coolant on the Daewoo Matiz car (Daewoo Matiz):
1. The replacement of antifreeze should be carried out on a cold engine! If there is no such possibility, then install the car on a flat site and allow the engine to cool a bit (20-30 minutes). This will avoid unwanted injuries, in the form of burns.
2. And at the time, while the engine cools, you can take the removal of the air filter housing. Weakening the tightening of the air corrugation clamp (photo 1), disconnect the corrugation from the air filter housing, remove the wire block from the sensor mass flow Air, we unscrew the three fastening bolts of the air filter body from the body (photo 2 and 3). We raise the air filter body, remove stubborn pins from rubber sleeves On the body (photo 4). And remove the air filter housing assembly.
3. Further, taken for the cooling electric fan. On the left side, disconnect the shirling block (photo 5). And 10 keys, we unscrew the two fastening bolts of the cooling fan diffuser from the radiator (photo 6 and 7). Remove the electrical fan with the case (photo 8).
4. We substitute under the right side of the cooling radiator, the capacity for draining the liquid, we find a wagoning nozzle, clutch the clashes and lower it down. We remove the pipe from the radiator and drain the liquid (photo 9 and 10). We unscrew the plug of the expansion tank.
5. In the same place, on the right side, we find a vapor apent and remove it (photo 11).
6. After that, go to the left side of the cooling radiator and remove the supply pipe (photo 12).
8. All. It remains only to remove the cooling radiator and drain, cut out the residues of the liquid (do not lose the rubber pillows of the guide legs of the cooling radiator - two at the top and two at the bottom). And collect everything in the reverse order, pour over the bayful neck of the expansion tank first 2 liters of antifreeze concentrate and after it, add distilled water to the "MAX" tag on the expansion tank. Run the engine and warm it up to turn on the fan. In the process of engine operation, follow the level of fluid in the expansion tank. The system will be deleted independently, so you have to periodically fill the water into the expansion tank. After the cooling fan has worked, you can drown the engine and give it to cool. On the cold level of antifreeze in the expansion tank should be slightly lower than the "MAX" tags (between the label and the weld).
Ready. It can be said that the replacement of antifreeze on the faithful Matiz was successful. If, the system is contaminated or you change the "color" of the coolant, then the cooling system will have to rinse. To do this, you will have to act according to the same scheme as described above - we drain the fluid, remove the radiator, the climb of it, we collect everything to the heap, pour water, warm up the engine before turning on the fan, weaving, let it cool a little, drain the fluid, remove the radiator and again We collect. And so until the moment when a clean liquid will be merged from the cooling system.
When using an article or photographs an active direct hyperlink to the website www.!
Replacing antifreeze B. machines DEU. Matiz, according to the regulations, should be carried out at a periodicity of 4 years, and in the case of active operation, at 80,000 km of run. In practice, the execution of this work may be required before, for example, when the color of the coolant is spinning or the appearance of a redhead. Such problems are usually associated with the purchase of low-quality products or non-compliance with the regulations.
What antifreeze is better, and how much to pour it in Daewoo Mathiz?
Choosing a cooling fluid for the car Daewoo Matiz, it is worth navigating on the manufacturer's recommendations and the year of release. Here you can select the following options:
- For machines from 1998 to 2002, the antifreeze of the class G12, red, is suitable. Available options - Motul Ultra, Castrol SF, Glaaself, AWM, Lukoil Ultra and others.
- If the car Daewoo Matiz is released from 2003 to 2009, then when replacing antifreeze, it is better to use cooling fluids of class G12 + (also red). Here are the following options - Lukoil Ultra, G-Energy, Havoline, Awm, Freecor and others.
- For the last batch of cars produced from 2010 to 2011, it is better to use the Red Round Class G12 ++. Best Products in this category - Glysantin G 40, Freecor DSC, VAG, Frostschutzmittel A.
After selecting a suitable co-replacement, buy the necessary amount of antifreeze. For Daewoo Matiz with a 0.8 liter motor, it will be necessary 3.8 liters working fluidAnd for a car with a 1-liter motor - 4.2 liters.
Replacement process
To successfully drain the antifreeze and fill the system with a new coolant, prepare the tool. You will need screwdrivers and a set of keys, pliers and a 5-liter empty container. In addition, make clean rags, ten liters of distillate, as well as two liters of coaching coat.
Drain of antifreeze and flushing of the radiator
To replace antifreeze, do the following:
- Install the machine on a flat site. It is most convenient to work on a pit or aleacade. If there is no such possibility, find a flat pad.
- Remove the "minus" with the battery, as a precautionary measure. After completing the work, return the terminal to the place.
- Remove the air filter and housing. To perform this task, release the bolt, which tightens the clamp on the nozzle. After that, unscrew the bolts holding the housing and remove the connector from the sensor.
- With the help of passage, squeeze the mustache on the clamp installed on the nozzle at the bottom of the radiator, and shift it in the direction to the floor. Pre-install an empty container where the spent, coolant will run. Now remove the hose.
- To depress the cooling system and merge the antifreeze faster, unscrew the plug installed at the extension tank output.
- Remove the upper bolts that hold the radiator. Next, dismantle the nozzle that is connected to the top of it.
Now it is necessary to rinse the radiator using the prepared 10 liters of distilled water. This work is obligatory if the antifreeze changed the color and acquired a brown (black) shade. In addition, the washing system is required if you decide to pour another cooling fluid. Having at the disposal, distillate is enough to wash not too dirty system.
It is worth noting that, in the process of draining the coolant, a small amount of antifreeze still remains, therefore it is better to use distilled water, and not different flushing fluids. Otherwise, a foreign composition remains in the cooling system, which is subsequently mixed with the new antifreeze. As a result, the parameters of the coolant deteriorate and its service life decreases. That is why, when replacing antifreeze on Daewoo Matiz, the problem of washing is worth focusing.
Flushing a tank distillate
As soon as the flushing of the radiator is completed, act like this:
- Using the passage, alternately, squeeze the three clamps on the tubes that are suitable for the tank, after which, dismantle it and rinse, with the help of distilled water.
- Return the clean capacity to the place and connect the tubes.
- Put the radiator and connect the connector to it.
- Return the air filter together with the case, after which, connect the air duct and the sensor.
- Pour distillate into the system. When performing this work, keep the canister with one hand, and the other - press several times on the nozzle.
- Get the engine and leave it, in this state, for 15 minutes.
Fill new antifreeze
The next stage of antifreeze replacement is the preparation of the coolant. Mix the concentrate of coolant with distillate, in an equal proportion, tighten the cork and mix the composition. Next, do the following:
- Mock the motor and wait for it to cool.
- Distille from the system, connect the nozzles to the radiator and the tank.
- Fill the prepared coil into the tank, pressing the lower tube of the radiator. Antifreeze must reach the top level.
- Tighten the cork on the tank.
- Get the motor for 15 minutes, after which check the level.
Now you know the main thing - how to drain the antifreeze, in what cases produce the system is washing, and how to do it correctly. In addition, in the process of replacement, it is important to carefully approach the choice of coolant and preparing to fill the system. The above information is enough to do everything yourself and do not go to a hundred.
Video: Replacing antifreeze, with washing system, on Daewoo Matiz (Daewoo Matiz)
If video does not show, update the page or
Antifreeze for Daewoo Matiz M250
The table shows the type and color of the required antifreeze for filling in Daewoo Matiz M250, manufactured from 2007 to 2010. Print
| Year | Engine | A type | Color | Lifetime | Recommended manufacturers |
| 2007 | for all | G12 +. | red | 5 years | Havoline, Motul Ultra, Lukoil Ultra, Glaaself |
| 2008 | for all | G12 +. | red | 5 years | HAVOLINE, AWM, G-ENERGY |
| 2009 | for all | G12 +. | red | 5 years | Havoline, Motul Ultra, Freecor, AWM |
| 2010 | for all | G12 +. | red | 5 years | Havoline, AWM, G-Energy, Freecor |
for example For Daewoo Matiz (M250 Body), 2007, with any type of engine, the carboxylate antifreeze class, type G12 + with shades of red. The approximate term of the next replacement of which will be 5 years. If possible, deposit the selected liquid for compliance with the requirements of the vehicle manufacturer specifications and maintenance intervals. It's important to know Each type of liquid is its color. There are rare cases when the type is tinted with different color. The color of red antifreeze can be from purple to light torus (in green and yellow Tezhe Principles).
Mix liquid different manufacturers - canIf their types correspond to the mixing conditions. If you decide replace antifreeze in the Matiz on your ownT. this instruction To help you. There should be no particular difficulties, everything is simple enough. These recommendations are suitable for replacing the coolant on Renault Logan.
So, it will take the following for the work:
- Two five-liter canisters with distilled water.
- Antifreeze concentrate in the amount of 2 liters. Use cooling fluid that is suitable for your car. For Matiza is acceptable to use high-end antifreeze. This is G11, G12, G13, which can be manufactured both in foreign and domestic factories.
- Tools: Cross and flat screwdriver, wrench on "10", pliers.
Replacing the coolant on Daewoo Matiz do it yourself
For Matiza, it is not necessary to look for a look or overpass, it will be enough for a flat site. We are waiting for the cooling of the engine so as not to get thermal burns.
First you need to pull the air filter housing. Unscrew the three bolts, squeeze the pliers of the clamp and slide the filter down the radiator pipe. Now carefully remove the nozzle itself, a little antifreeze will fall out of it, it is normal.
Prepare an empty capacity with a minimum 4 liter volume and unscrew the lid of the expansion tank. Drain the waste fluid.
The next to our action will be the removal of the radiator together with the fan, which is fixed by bolts. The radiator is released from the residues of the liquid, we rinse it well with water. Take the pliers and remove the expansion tank. Also rinse it with water.
Expansion tank and radiator put into place. Check how reliably is attached to the radiator the filter housing (remember the sensor connectors) and the nozzle removed. Now fill the distilled water in the tank (4 liters), the bottom nozzle with your hand. Expansion tank Close the lid and get a car.
Wash the cooling system will be approximately for 15 minutes. By the way, you can additionally use special means For flushing, they will help more effectively solve the problem of deposits in the system. They are sold in any auto shops and have detailed instructions on use.
Now prepare antifreeze. In the released container, mix the concentrate and distilled water. The proportions are determined by the climatic conditions in which the car is operated, but the concentrate content should not exceed 70% or be less than 50% of the entire composition. Exact instructions you will find in the annotation to the product.
Engine stop, and let him cool again. To merge wash liquid, you need to do all the same disassembly actions that were described above.
Fill the cooked antifreeze to the maximum mark in the expansion tank. Lower pipe Clean the hand, you will reduce the number of air traffic jams and help the fluid more evenly distribute the system. Close the tank lid and make a matz. The car is mohawing and check the coolant level. If you do not want to wait a long time until the engine cools, cover the cover with a thick cloth and carefully open until all pairs come out. Antifreeze, most likely, will have to attach. Check how reliable all the attachments are, there is no leakage of liquid. A few days later, once again check the cooling fluid level.
