IN agriculture Do not do without a tractor. However, this pleasure is expensive, so the homemade tractor can be a decent solution to this problem. The case is not easy and requires the presence of tools, the necessary materials and knowledge, however, the result will be pleasantly pleased.
How to make a minitractor with your own hands: What is needed for this?
The most accessible option for a minitractor is your own tractor with the so-called broken frame. Such a frame consists of 2 parts, which are connected by a special mechanism based on hinges. In front of the machine there is all control and chassis. The control is based on hydraulics, the entire front part is strung out when the steering is rotated, resulting in turning. This approach allows you to simplify the design and save on some details.
The rear is easier by design, it is located on it. workplace For the machine tractor, the rear axle and various devices for the installation of mounted parts, which produce soil processing.
The advantages with which the homemade mini tractor for the household posses:
- With its small sizes and simple design, it is capable of giving results comparable to industrial appliances.
- It has excellent maneuverability, it is able to make a turn on almost one plot of land, which is rather important quality for soil processing.
- Low flow Fuel. Of course, fuel consumption depends on the design of the machine and the work performed, nevertheless, the fuel consumption is minimal.
- Low cost, incomparable with the purchase unit. The low cost is provided to cheap nodes and parts that can often be bought from hands or find it.
Disadvantages of self-made tractors:
- the unit is performed from the old ones, sometimes the details that have narrated its age, so it is recommended to regularly carry out the maintenance of the machine (in any case there is no guarantee that the old node will not fail);
- when the old node fails or the part, it is not always possible to find a replacement, since such components in most cases have already been discontinued.
Before starting searching for spare parts and mechanisms, you need to think about the design of the machine and find the drawings. The drawings can be thought out independently, but it is best to take advantage of the projects of folk craftsmen who have already had the experience of assembling such equipment. You can advise in advance with an experienced fitting, which will help take into account and eliminate possible problems In advance and advise how to collect the tractor.
Necessary materials and tools
The following tools will be needed for work:
- welding machine with electrode reserves;
- cutting machine with a set of cutting and grinding discs, hard brush for metal stripping;
- spanners, a hammer with a chisel;
- electric drill and drill set;
- painting equipment;
- you may need a lathe for boring some parts.
Materials that will have to find in order to collect a minitractor:
- metal frame chaserler;
- axis with wheels;
- nuts, bolts and washers of various sizes;
- driver's seat;
- engine, gearbox, transmission;
- materials for creating a housing, roofs, wings;
- consumables for painting;
- lubrication for tractor nodes.
Search for necessary spare parts and assembly design
Before you begin searching for all nodes and mechanisms, you should know that the gearbox, the engine and chassis must be taken from one tractor - this will avoid difficult work on fitting nodes to each other.
What engine is most preferable for a homemade tractor? Here the choice is small: It is recommended to find the engine UD-2 or UD-4, the M-67 engine will become a good option, since it is quite economical and durable, requires minimal participation in maintenance and repair. Some folk craftsmen used the engines from the car Zhiguli as a force. In this case, the engine is removed from the car with a gearbox and transmission, there is no need to fit the mechanisms to each other, which greatly facilitates the assembly.
Before installing such an engine, it should be upgraded. It does not have a cooling system, for this you can use the fan that is installed on crankshaft. It is necessary to install the casing that will direct the flow of cold air.
If the engine is used from a passenger car, it is necessary to reduce its turns 3 times with the help of the appropriate gears, since such a tractor needs such high revs.
The selection of the wheels depends on what purpose a home-made mini-tractor is intended. If the purpose of using the machine is to move various goods, you can do with 16 inches wheels. If the tractor will work on the field and process the soil, it is recommended to use the wheels of a larger diameter - this will provide the best grip with the soil. If there is a desire to save on wheels, you can use and car tiresHowever, it should be borne in mind that in this case the clutch with soil may be insufficient, and control can be complicated.
Rama, rear axle and exterior finish for mini tractor
The frame of the collected mini tractor consists of 2 parts connected by a hinge mechanism. For the manufacture of such a mechanism, you can use cardan Val. from large truck, for example, gas. It is not so important which specifically the car model will be used: the cardan shaft has no special difference.
The rear axle is quite suitable from the old car Volga or Muscovite, but in this case they will have to shorten them, since the standard bridge is not included in the dimensions of the mini-tractor.
The frame is made of metallic chawller. This material has sufficient strength and rigidity for such a load. After mounting the frame, the holes of various diameters are drilled on it in order to fix the main components and mechanisms.
External finish can be performed from any materials: both from metal and plastic or fiberglass with epoxy resin. The design is necessary to paint well at least 2 layers of paint for metal. It is necessary not only for giving a tractor external view, but also the protection of its nodes from corrosion.
As can be seen, homemade completely pays for itself, and in the manufacture of a small tractor for agricultural worker (in the presence of skills and tools) there are no special difficulties.
This article will describe the process of manufacturing a homemade minitractor with their own hands (in the conclusion of the article, video is provided), it is described about the types of this agrotechnology, the benefits of use.
The area of \u200b\u200bagricultural activities in many of us has associations with the processing of soil cover. But in order to grow any vegetables, fruits, berries need not only to plow the earth and fertilize it, but also constantly water and get rid of weeds. An excellent assistant in solving such tasks will be a mini tractor. This agricultural engineering simplifies significantly.
Although the minitractor has small sizes, with the tasks set, it copes successfully: plowing the soil cover, its loosening, mowing of grassy vegetation and other diverse works that have a connection with the processing of land for landing of different plants.
Large enterprises that are engaged in agricultural activities are used by mini tractor domestic production. How to be an ordinary farmer? In view of limited money Private farmers can use homemade agricultural engineering.
Views
There are three types of this agrotechnology:
- A technique that has many functions capable of performing a variety of works, such as the processing of land, mowing herbal vegetation, getting rid of garbage and the like. The data of the minitractor tools with a motor having an average power - this will be acceptable for processing approximately six hectares of land. Also, the tractor can be equipped with attachments of attachments, which will help increase the range of tasks.
- The tractor whose task is only in graze the grass and get rid of garbage. This car It is capable of processing only two hectares of the site. Especially often this species It is used for a lawn haircut.
- Rider. it last species Mini tractor. The main task of this agrotechnology is to fertilize the soil and bring minerals. When equipping additional equipment, you can also use for processing soil cover. However, the area of \u200b\u200bthe processed territory in this case will be small.
Advantages and disadvantages
It should be immediately noted that data homemade machines Enjoy mostly private farmers. The main advantages of mini tractors made by hand:
- Excellent deep treatment land plot. If the soil processed is stony, it is very difficult to physically handle it manually. Therefore, the mini-tractor in this case is irreplaceable, which in a short period of time will cope with the assignment;
- This agricultural engineer is very convenient to use on small areas in the area for processing huge fields (more than ten hectares) only an ordinary standard tractor.
- Total small cost. A mini-tractor made with your own hands will help you save a decent amount of money. In this case, all expenses will include financial resources spent on necessary materials, for the construction of agricultural equipment. Also no additional costs for repair work are not required;
- The minitractor can be equipped with additional devices, thereby you can increase the number of functions of this machine. The construction does not have a huge weight.
The homemade unit also has a number of shortcomings:
- The owner who wants to independently make a mini-tractor, you will have to look for materials yourself, and this is a sufficiently long process;
- A rare component part can be used for assembling it can be very difficult to find it. However, for assembly, materials are used that are very easy to find on the market, as well as them can be easily replaced in case of breakdown;
- For the tractor made with your own hands, you need to get permission to ride on the roads of the city, otherwise otherwise you can get a serious penalty.
But these are not such serious disadvantages, more advantages are more significant.
Assembly Guide
Observe a specific action algorithm for assembling this agricultural engineering:
- At the very beginning it is necessary to make a frame. For this apply steel channel. Also in the overall construction must be present quick-use lifting devices (traverses). Traverts must be from the front and back. Basic power elements (spars) should also be located. To make a frame, you need to slightly reduce in the size of the width of the front. After that, it will be possible to make a detail in the form of a trapezoid. Do not forget to make a small hole in the frame - this will help the rest of the devices in the future;
- Next are used racks that need to be welded to the corners. The role of racks is to create a subramcier. Additionally, they must be combined at the top of the design. Then it is necessary to attach the wheel of the wheelchair ( rear axle);
- Then there is a motor installation. The motor must have sufficient power. For installation, the engine of the ordinary motorcycle will fit;
- Installing the gearbox is carried out on the frame. It should be in the direction towards the driver. In the future, this will help to easily control the tractor;
- Create steering. To control the steering wheel, taken from a car of domestic production. In the extreme case, you can use the wheel of the motorcycle;
- Installation coupling device. It is intended for the trailer.
- Creating a brake. Then the electrical system is connected.
If you are engaged in a small farming, such a technique as a minitractor you need. With him you can perform a mass of everyday agricultural tasks in a short period of time.
Make your own hands Mini tractor is not much difficult. Of course, you need to have certain knowledge. You can buy them when watching a video:
Mini tractor - an extremely useful tool in agricultural economy. They can do tens of the most different work: From landing frills to harvest and snow cleaning. If the agriculture has the skills of handling appliances and a tool, then independently assemble the unit for him will not be great difficulty. In this case, the cost of the main device will be minimal.
Tools and materials
Small tractor Significantly helps in the work of the Agriana. They can handle land of naughty and summer cottages, collect harvest. The big advantage of the aggregate is that it is possible to connect the most attached attachment equipment. Compact mini aggregate everyone is good, it is only worth a lot of money. Even chinese manufacturers Recent years have become significantly raising prices. Therefore, some craftsmen make small aggregates with their own hands, and in quality these mechanisms are not inferior (sometimes even exceed) factory products.
Before starting such a job, you should understand how one or another node works as it works, what features he has. This technique is needed, as a rule, for 3-4 types of work, so when creating an aggregate, you can "place accents", for example, to strengthen the frame (if there is an increased load) or put wider wheels if the main work will occur in field.
Make a mini tractor just enough, he will not be particularly different from the real tractor. First of all, you should make a plan to create a similar unit. There are many spare parts for used motorcycles, vases and oaks on the market, so finding a suitable node will not be great difficulty.
Beam / bridge can be made with additional fasteners, since often factory analogues do not have the necessary coefficient of strength. The homemade tractor can be without a cabin, but it is not always justified, especially during operation in the hot or cold season. BOV is a power take-off shaft, which makes it possible to work attached units. Types of shafts:
- conjugate
- autonomous;
- working synchronously.
The frame can be made from the corners "6" or pipes with a diameter of 45 mm. In order for the design to be more stable and durable, metal plates (6 mm thick) are welded in the corners. PPC can be taken from the vase. It is important that in its working condition there are at least three speeds of the front and one - rear. The craving can be "borrow" from the motorcycle. Steering column Suitably OT domestic auto Type "Zaporozhets". It is also realistic to make a mini-tractor with different engines - both single-cylinder with air-cooled and four-stroke carburetor. Such power plants are ideal for creating agricultural machinery.
Benefit from creating your hands a miniature tractor:
- low price;
- you can make an aggregate that will make the most suitable for personal needs.
From the disadvantages you can allocate:
- the process of creating a tractor may seem like labor-intensive for those who worked little with technology;
- car engines work on gasoline, and it is more expensive than diesel fuel;
- leve federal highways On this technique it is impossible, you can get a fine.
How to make your own hands?
Creating a miniature tractor begins with a frame mounting that can be made from the tubes. Making such a design should be powerful, but at the same time it should be not very heavy. Often, the frame is made double. Also popular aggregates with a so-called "broken" frame with a full drive from GAZ-52 are also popular. The "breaking" frame makes it possible to deploy a tractor over a small radius, which increases the maneuverability of the device. The most important blocks of a mini-tractor:
- wheels;
- bridges;
- transmission;
- power point.
The mini-tractor, made independently at home, begins to be created with the study of drawings and plan schemes. Taking a "related" project for the starting point, you can edit it, to make your own adjustments. After the individual project has been prepared, he draws on Watman Sheet. Next, you will need to collect all the necessary nodes, make the basis of the future unit. The dimensions of the frame can vary depending on the purpose of the machine - length it can be 1.5-2.5 meters, width - 1.3-1.8 meters.
A very important node - hydraulic drive, it gives many advantages in the work and makes it possible to manage the most different equipment. The hydraulic node is especially valuable in this regard. Its presence will allow the use of the most different attachments - from KUN to the brush for snow cleaning. Hydraulics consists of:
- hydraulic cylinder 76x80;
- distributor P82;
- pump NSh12.
The pump operates at a speed of 1000 revolutions per minute, sometimes it must be turned off. With the engine, things are easy, the power plant can be put from any car or motorcycle.
Not bad engine UD 25. This is a two-cylinder unit with a capacity of 12.2 liters. p., The volume of the engine is 0.43 liters. The model is very successful, although it is no longer produced, but on secondary market Such aggregates have a huge amount. It is worth such a model not more than 8 thousand rubles. PPCs can be taken from VAZ or DVS "Ant. If the tractor is used in the field, then the wheels are rational 20-24 inches. Front beam is simply prepared:
- two "cams" are collected, which can be taken from "Zhiguli";
- from the pipe (45x45 mm), the square is made by welding;
- it is attached to the frame with welding, the "4" corner, they are mounted and the "cams" of turns are mounted and fixed, steering steering.
The mini-unit beam has a swinging mechanism that is taken from the VAZ to a closer with a cross. You can also take a similar element from the UAZ. It is very important that the bridges have congruent gearboxes. It is necessary that the wheel rotation factor is the same. PPC is taken from any car. With 2 boxes, the mechanism will be even more functionality.
It is important to take into account that when installing the hydraulic device, a certain power of the engine is due to its service. If the engine is low-power, then the hydraulicock is better not to put. Bom begins to rotate from the engine crankshaft, respectively, it depends on the number of revolutions power plant. There is also a synchronous type, its rotational coefficient is associated with quantities. gear ratio mechanism. This feature is in demand, for example, when conducting a sowing campaign.
Creating a point suspension allows you to apply to machinery optional equipment. The three-point suspension is also very important, it should be dynamic horizontally and vertically, which makes it possible to manage the machine better. The brake is advisable to put on rear wheels. You can take ready-made knots from VAZ, you can also "borrow" brake pads. The clutch can be removed from any old "Zhigul" or gas. Steering is also taken from Vase. It is better to provide a cabin for the unit to work, then it will be more comfortable, labor productivity will increase. You can make this node from pipes with a diameter of 20-25 mm, which are welded in the form of a frame. It can then be cut:
- plywood;
- tin;
- plastic.
Each unit has its own characteristics, so the drawing should always be conjugated with specific device. For example, it is often necessary to mount the mechanisms:
- front-turn;
- rear-wheel drive;
- small with an on-board turn mechanism.
Usually, the height of the cab does not exceed one and a half meters, over the head of the worker, the ceiling must be at a distance of 20-30 cm. Before making the cabin, it is necessary to collect the "skeleton" of wood storage products. After everything is understandable with dimensions, you can cut the tubes. Frameworks are made using welding. After the frame is ready, it is trimmed, they put frames for glasses, etc. The most time consuming part of the work is the creation of doors. It will be necessary to mount such elements:
- thin tubes;
- restores;
- fastening.
The design should be light and durable at the same time. To make the door with automatic, you can put gas elevators. From the inside the cabin can be seen by dermatin or foam sheets, if you have to work in the cold season. Do it yourself can also be done crawler. This technique has great dynamism and maneuverability. Caterpillars have a gentry effect on the ground, so it is beneficial to use such a mechanism in many ways.
Frame is made from corners, pipes or chambers.The engine is preferable to put diesel. The front and rear axle can also be "taken" from the vase. Good gearbox is in GAZ-53. Caterpillars are made of tires, they are cut off with the help of the sidewalls. Wheels are mounted on the resulting equal rubber blanks. So that the car can dynamically make maneuvers (reversals, etc.), must be installed the differential, which can turn off the rear and front wheels if necessary. This is done like this: it is pressed on the brake pedal, the differential switch is made. One wheel freezes, the second continues to move, the unit in this case unfolds.
From the cargo motorol
If you make a tractor from a scooter (for example, "Tula 210"), then it will be weighing no more than 90 kg. If the main nodes are taken from one source (this may be "gas", "VAZ" or "Oka"), then less time to refine and fit the details. Magneto with one pole is put on the engine of the engine. When installing onboard gearboxes (1: 4), the mechanism will be able to function at minimum speeds, while it will not change the traction force. This factor is very important during harvest, as well as when cropping.
Frame is made from the corners "4". Capacity for fuel can be "borrow" in a passenger car or make a 2 mm from the sheet itself. On such a mini-mechanism you can transport to three hundred kilograms of various goods, to make a plowing of a depth of up to 17 cm.
From "Oka"
The mini tractor can be done by taking spare parts from "Oka". A small-format car can successfully fit the parameters of a small agriculture. In any case, the wheels, the engine, fuel capacity, transmission - all these nodes may well come up. Such an aggregate will be distinguished by the capacity and economical flow rate of fuel and lubricants. Such a mechanism will cope with the following types of work:
- enhancement;
- processing of soil;
- plowing;
- transportation of goods.
From "OKI" such nodes are used:
- power point;
- transmission;
- bridges;
- wheels;
- steering thrust;
- chassis.
In the manufacture of the tools and some materials will be required:
- apparatus for welding;
- screwdriver;
- turbine;
- metal in sheets.
To make a frame, you will need a couple of spars (made from channels 10), as well as two traverses (12 and 16). For the transverse mount, you can use the "6" corner. The engine is better to put a four-cylinder, with a capacity of 45 liters. p. because it presents the system air cooling. Bridge redo optional, it can be left unchanged. To make a transmission, you need to attach the checkpoint to carrier frame. In the flywheel, the rear wall is cut off, the hole is cut in the center.
To maintain the desired pressure in the hydraulic system, a pump is required, which is placed next to the shaft. Each shaft wheel is controlled by a gearbox. If work is a lot on rough terrain and in the field, put better wheels more (up to 24 inches). Typically, such aggregates are absorbed without springs. Spars, both in front and behind the back to further enhance. PPCs permit from "Oka". If you put the engine from the "UD2" (it is more powerful), you can work with large areas and carry heavy loads. Cabin, lighting, fuel tank is installed.
From "Loise"
The unit made from Loise may be all-wheel drive, and the rear-wheel drive can be turned off if necessary. To make such a tractor, you will need a small amount of effort and working time. The engine can be delivered to Sadko DE-310, you can put two gearboxes to it. Frame is made from corners or chambers. The hydraulics is used to work the H12 pump, the 78x110 hydraulic cylinder works in it, the P82 distributor. The pump is used only in some cases. The shaft, as well as the PPC, can be taken from any motorcycle, sometimes the shaft is cut (or prolonged), a new "asterisk" is put on it. The power take-off shaft is also easy, it will be no more than 1.5 thousand revolutions per minute.
From "Zhiguli"
The easiest way to create a tractor from "Zhiguli" is the most acceptable option. You can always find a variety of spare blocks. Unfortunately, the power plant in "Zhiguli" works on gasoline, and it stands in our time. The lion's share of agricultural equipment functions on diesel fuel. When planning a project to create a mini tractor from "Zhiguli", several issues should be solved. The engine is placed in front of the driver and must necessarily have a protective screen. The frame is made from the corners "4", its size is 1.2 x 2.1 meters. The fuel tank is placed in the back, it can be done independently from tin or take from any passenger car.
The front suspension is necessarily enhanced. The drive is made on 4 wheels. All work is done on this algorithm:
- the scheme is prepared;
- rama is done;
- created body;
- all nodes are combined;
- installed steering.
Mini tractor from "Zhiguli 2106" will be powerful enough to do all necessary work and transport cargo to 500 kg. Also when creating it, you can take various nodes. From GAZ-53 the gearbox is taken, the bridges are taken from "Zhiguli". Wheels can be taken from MTZ-84. When installing the wheels, bridges should be strengthened, you may have to change the brake.
VAZ engine has a power of 59.4 horse power (There are more powerful). Engine volume - 0.65 liters. It has a good efficiency and relatively small fuel consumption. When creating a mini-tractor from the "Vase", it should be especially carefully reading the layout and location of all nodes. At the very beginning, you should decide on the location:
- capacities with flammable;
- power plant;
- protective screen;
- cabins.
Rama is rational to make shorter, and the suspension is better to put more powerful. PPC can also be taken from GAZ-53, wheeled pairs from different machines. From the "vase" only the rear axle, the steering block. If there are installation plans full drive, then you need a motion of at least 42 liters. from. Such an aggregate will be able to pull the hydraulic VOM, it will work normally with an increased load. The tractor is better to do all-wheel drive.
The process of creating a mini tractor from "VAZ":
- conducting welding with the frame;
- installation of chassis;
- installation of wheels and fuel tank;
- installation of power installation and transmissions;
- installation of the cabin, protective screen (casing).
An important part of the work is shortening the rear axle:
- a cup is cut off, the ring of the flange is removed;
- it can be removed, fluttered;
- inside the cup drills a hole;
- semi-axes are aligned and weld;
- the bridge is inserted into the finished recess;
- welding works are carried out;
- the bridge to the frame is attached using a V-structure.
From "Zaporozhets"
To make a tractor from "Zaporozhets", you should work with nodes. Front and rear axle can be a little shorten. The gearbox on the "Zaporozhet" is not very powerful, it can be replaced with a box from "Vase". The hydraulics is quite suitable, but may have to change the hoses and fittings to newer. The frame of the cab is made of pipes with a diameter of 2 cm, is trimmed with plywood or PVC sheets. The engine "Zaporozhets" is quite suitable for the tractor, but you can put something more powerful. If you install the "VAZ" checkpoint, then you can work with any attachment. All used units must pass thorough cleaning and verification.
From motorcycle
You can collect the tractor and from the Ural motorcycle.
He was done like this:
- A frame welded, which consisted of two blocks. Pipe length - 2.1 meters, width - 0.95 meters.
- Transmission is placed from VAZ. The torque pulse is transmitted through the chain on the "asterisk", then goes to the drive shaft in the front and rear axles.
- Mounted electronic ignitiontaken from "VAZ2109".
- Two gearbox is raised - from the motorcycle and car "Moskvich 412".
- The drive is full. Cylinders have air cooling.
- Steering thrust are taken from Moskvich.
The machine is quite powerful, passable, "pulls" without special difficulties a trailer with a load weight up to 0.5 tons. You can use it both in agricultural work and for cleaning the territory from snow.
Safety technique
When working on the tractor, security techniques should be followed:
- to work on the tractor, you need to have a special training;
- before starting the engine, the transmission switch is in the "H" position;
- the hydraulic distribution clutch is set to the "Neutral" position;
- the water barrier can be cross if it is a depth of no more than one meter;
- transportation of people and animals on the trailer is prohibited;
- in the cockpit, only two people may be present;
- on the floor of the unit should be a rug made of rubber;
- before starting work, a preventive inspection of the engine, cabin, fasteners, gearbox should be made;
- if the car was standing for a long time without movement, it should be "driving" it at idle, without loads;
- the steering force should be no more than 0.44 rad (26 °), with an indicator of 0.62 glad (36 °) will need to adjust the hinges;
- the brakes should be regularly checked and regulated if necessary;
- the pneumatic system should have a pressure of about 0.5 MPa (4.78 kgf / cm2);
The presence of your mini tractor in household Significantly simplifies the exercise of a large amount of homework. One of its main advantages is saving and mobility in limited locality. Sufficient to equip your homemade tractor by all additional devicesAnd he will be an indispensable assistant in the processing of not very large land areas.
Under the conditions of maintaining their business conjugate with the production of agricultural goods on household sections, the tractor is effective technique. As it can not allow new special equipment at the initial business development stage in the initial stage of business, but to build your homemade mini tractor and everything from the primary parts is absolutely for those who have basic knowledge Maintenance art.
With the help of your homemade mini tractor 4x2 Implement the entire list of specific works:
- cleaning snow;
- transportation of not very large cargo;
- cleaning home debris, as well as different vegetation;
- harvesting hay;
- landing and spraying vegetables, etc.
Production options homemade minitractors quite a bit of. Some homemade things are designed on the basis of motors with old domestic or foreign cars and motorcycles. Others are selected with existing equipment such as a minitractor.
Creating a homemade mini tractor
The tractor includes a complex complex of structures and elements of directly interdependent among themselves. Before starting work, you should decide on the design of the homemade, which you can read on the forum. Consequently, the presence at the arm of the drawing materials will greatly facilitate its production.
To implement production at the proper level, from Clematz will need:
- study of basic knowledge of adaptation;
- the presence of a single row of nodes (boxes, power aggregate) and mechanisms.
In addition, the presence of a layout and drawings will serve as a landmark in the direction of the formation of self-made adaptation.
Mini tractor design
The design described was invented and tried in practice, which can be read on the forum. Do it yourself such a minitractor allowed from Utyl: different nodes and elements from the former serial carsmanufactured by the domestic industry.
The unit can be equipped with a huge set of plug-in trailed and suspended guns. Thanks to this, the mini tractor can be considered a multipurpose assistant in the household economy. It is allowed to be used for the purpose of plowing and harrowing, cultivation and enhancement, and, in addition, with the aim of other actions related to the cultivation of the Earth and the departure of plants.
This tractor is also allowed. use in a clutch with a uniaxial cartTo transport different homework, garbage from place, soil, sand. To do this, a small modification of the tractor is performed, and the driver is located on the seat in front of the cart.
What will be the minitractor?
The first thing to be done before collecting equipment is to navigate, from which knots it consists of what can be read on the forum.
The simplest adaptation of the compact tractor includes the following elements:
- hydromotor (in the role of the motor can act a motoblock or a motorcycle);
- power frame in which all other installations are fixed;
- brake system;
- assembly with brake discs;
- running partincluding wheels and wheels;
- sUSPENDING SUPPLY SYSTEM;
- steering column;
- comfortable armchair for the operator;
- rear and front lights.
Each of the mentioned parts you need to buy, find and collect pushing out of a clear universal drawing, in order not to disturb the proportion of the aggregate.
How to make a homemade mini tractor?
In order to construct such equipment, many methods are used, however, as a rule, the algorithm is the following:
The drawings on the mini tractor can be found on the Internet, the right view or develop personally, in case there is knowledge of the mechanic.
Types of suspended equipment
To increase the prospects interval, this device can be equipped with suspended equipment, which can be done with the help of existing primary means.
So, you can independently make the following types of suspension equipment:
- diverse seeders;
- rankers and Rippers of the Earth;
- plows are single, double-circuit, simple and rotary;
- collapsible haymers for harvesting feed and more.
Over time, this type of tractor can be upgraded by identifying auxiliary devices, which will increase the comfort and security of management. In addition, such an aggregate according to its own personal useful and multifunctional distinctive traits Most industrial modifications will overtake in many respects.
