Hyundai Accent is a fairly common car in a wide circle of car owners. For many years, the model managed to take root on the streets of many cities. The older it becomes a car and the less frequently technical inspectionsThe higher the likelihood that problems arise with electrical and instruments. With such faults, check primarily fuses and relays Hyundai Accent.. If there is no manual at hand, this article will help you.
List of fuses in the block under the hood
1 (100 A) - generator. If the battery began to quickly discharge, most likely the case in the generator and the absence of the battery. Check this fuse, the tension of the generator belt, contacts the connector on the generator, as well as the wiring. There should be no short circuits in the car chains. Check the voltage on the generator terminals when the car is hired (if there is no experience, better contact the electrician).
If there are no voltages on the terminals, brushes inside the generator may be worn out, in this case it can be cheap it. If, when the pulley turns the pulleys or extraneous sounds, the bearings were most likely collapsed. In this case, it is better to replace the generator for a new one or to give to repair.
2 (50 a) - Locking doors.(electric), stop signals, alarm, beep, heating rear glass, interior lighting, the electronic unit Management (ECU).
If you do not work any stop signal (including cabin on the rear window), first of all check this fuse. If it is a whole, most likely the case in the "frog" (switch in the block over the brake pedal), the connector or wiring.
If only one stop signal is lit, most likely burned the lamp. The lamps are two-dimensional, one thread on the enabarity, the other - on the stop. You can measure the voltage on the lamp connector when the brake pedal is pressed, if it is there, the case is in the lamp. If not, most likely wiring. Look also look at the lamp connection scheme on the "Schemes" tab at the top of the page.
If not working " avoidance"- Check this fuse, fuses 1 and 7 in the cabin and relay 10 in the cabin, and then the power button and wiring.
If not working klackson (Beep), it can be in this fuse, in the device of the beep, wiring to it and switch on the steering wheel. Try briefly submit a 12 V voltage from the battery directly to the signal terminals. If the sound does not hear, repair or replace it. This is pretty frequent problem, especially in rainy weather. If the sound is, check the contact to the ground, it must be reliably fastened. Wires should not have disconctions and melted isolation.
If not working heating rear window, also check the fuse 9 and relay 8 in the salon mounting block. If they are working, check the contacts of heating elements on rear standAs well as threads on glass for cliffs.
Detected breakage can be fixed with special conductive glue. You can check the voltage on the contacts of heating elements, when the button is pressed, it should be there. If there is no voltage on terminals, check the wiring laid through the body and the help of the button.
3 (30 a) - headlight and lamp dimensions. If headlights or dimensions are not burning, check the fuses 27, 28, then in the relay cabinet 4, the lamps themselves, connector contacts, wiring and switch.
4 (20 a) - engine control unit. If the engine does not start, it works not exactly or stalls without visible reasons, check this fuse and its contacts, as well as fuses 5, 6, 16, 17, 18, 21, then in the salon unit 5 and relay 3. In addition to wiring, it's It may be in the fuel system, fuel pump, the ignition system, candlelight and other components. If there is no experience, it is better to fully diagnose the engine in.
5 (30 a) - engine start, ignition coil.
6 (20 a) - radiator fan. If the engine cooling fan does not turn on, check the relay 18 and the fuse 10 in the cabin unit. Try to submit a voltage of 12 V from the battery directly to the fan, thereby eliminating the variant of its breakage. It can also be a case in the sensor temperature of the coolant (DPT) or thermostat. When signs of high temperature and engine overheating appear, immediately jammed it. Otherwise you can get to expensive repairs. If there is no experience, it is better to contact the workshop.
7 - connector.
8 - heater fan relay. If you stopped working the stove and in the cabin coldly, check this relay, as well as fuse 40. If the heater works only in maximum speed mode, check the resistor that is responsible for the fan modes. If necessary, replace it with a new one. If the stove does not work in any of the modes, try to apply the voltage 12 to directly from the battery to its motor.
To get to the motor, you need to remove the lid under the main glove box. If the motor does not work, it will be required to repair or replace a new one. In the presence of funds, it is better not to buy and buy a new one. If the motor works, check the wiring and serviceability of the stove mode switch (along with its contacts).
9 - Sound Relay
10 (10 a) - Salon Lighting. If the light in the cabin does not light up, check in addition to this also fuse 2, the serviceability of the lamp and contacts in the ceiling, wiring. If the light does not light up only when you open the door, check limit switches On the body that react to opening and closing doors.
11 (10 a) - audio system, radio tape recorder. If the radio does not turn on, check out this fuse, then remove it and check the contacts in the rear connectors, as well as the fuse that is located directly on the wire (usually red). Wiring can also be caused. Check where the power supply on the radio is served from the ignition lock or directly from the battery. If the required wires to submit direct voltage 12V from the battery, the radio should turn on. If it does not turn on - most likely a malfunction from it inside and requires repair or replacement.
12 - Relay 2 Air Conditioner Heat Exchanger Fan. If the air conditioner stops working, check in addition, the fuses 13, 19, 20, 22, 32, as well as in the cabin fuses 10 and 17. If they are all better, it is possible in the system there are no freon and you need to fill. It will not be superfluous to check the entire system and tubes for sealing and no leaks. In winter, it is recommended to occasionally turn on the air conditioner so that in the spring it does not arise problems.
Look also at the compressor under the hood, when it is on, its coupling must be spinning. If it does not spin, or there is no freon, or one of the components of the systems is faulty.
13 - air conditioner compressor clutch relay. See previous item.
14 - fog headlight relays. If none of the foglights do not work, in addition, the fuse 24, then in the salon block 10 and relay 2. The front and rear PTF are turned on by different buttons. Check the contacts and the correctness of the corresponding button on dashboard, as well as wiring. If only one "fog" is not lit, check the voltage on its connector and replace the lamp when it is presented.
15 - reserve.
16 (15 A) - Regulator idle move (XX), position sensor distribution Vala (DPRV).
If the engine does not hold idlingdoes not start, stalls or work unstable, check this fuse, as well fuel system and gas station. The reason may be in addition to electricians in poor-quality fuels, spark plug, nozzles and other components. If there is no experience, it is better to contact the diagnostic station.
17 (10 a) - engine control unit. See information about fuse 4.
18 - radiator fan relay. See information about fuse 6.
19 (10 a) - air conditioning. See information about fuse 12.
20 - Relay 1 Air Conditioning Condenser Heat Exchanger Fan. See 12.
21 (10 a) - engine control unit. See 4.
22 (10 a) - air conditioning compressor coupling. See 12.
23 (10 a) - beep. See 2.
24 (15 A) - fog lights . See 14.
25 (10 a) - Heat Lamp on the right side.
26 (10 a) - Head light lamps on the left side. If both headlights do not work, see 3. If one headlight works, and the second is not, check out one of these fuses, as well as the function of the lamp and contacts in its connectivity.
27 (10 a) - Front and rear lamps of overall light on the right side.
28 (10 a) - Front and rear lamps of overall light on the left side. If not a single lamp of the dimensions is lit, see 3. If the lamps do not burn only from one side of the car, check out one of these fuses, lamps and their connectors.
29 - Relay lamps of dimensions. See 3.
30 - generator pre-excitation resistor. See information about fuse 1.
31 - starter relay. If you turn the ignition key, and the starter does not twist, check this fuse. If it is working, check the battery charge and fastening the terminals on it. They could oxidize or relax. Clean them inside with a skin or a round file and fasten it well at the battery terminals. If after that the starter does not start twist, check it, closed the 2 contact with a scrap or metal object.
Make sure that the gearbox lever is in a neutral position. If the battery is charged and the starter when contacting contacts or feeding to it voltage voltage 12V does not work, most likely it failed. In this case, repair can help (replacing brushes or other wear parts) or buying a new one. If the starter works only with direct voltage supply, check the wiring and ignition lock. Perhaps the tracks were oxidized in the castle or there is no contact in the connector.
32 (20 a) - heat exchanger fan capacitor of the system of conditioner. See 12.
33 (30 A) - Electrical windows. If none of the windows are working, check in addition to this relay 7 fuse in the cabin. If the window lifter does not work in one particular door, check the wires between the door and the body (often in this place they are reheated), control buttons on the door, as well as the lift mechanism itself. To get to it, you need to remove the door trim. All cables should be on their grooves, gear should be integer and the motor should work. Check also that there are no foreign objects in the mechanism.
34 (30 A) - Anti-lock control unit aBS system . If the ABS system ceased to work on slippery coatings and wheels when braking are blocked, check this fuse. If he is a whole, it can be in the ABS block, which is under the air filter. In it could fail the motor or wear his brushes.
35 - Middle Light relay included constantly. If both eagle light lights do not work, check this relay, as well as lamps and wiring. Both lamps could overcome. If only one headlight is not lit, check the lamp and contacts in the connector. Lamps have 2 threads - one to the closest, other on the distant light.
36 - Relay fuel pump . If the gas station and the sound of its operation stopped working when the ignition is turned on, check this relay and wiring through the cabin to the pump. Wires are usually laid under the driver's door threshold and then on the body. Check that there are no damage, melting and twist.
When you detect twists, they must be reliably sued. If you set the alarm, then it was possible to put an additional relay for blocking the fuel pump. In this case, check it. Usually this relay is behind a small glove compartment. You can also apply the voltage of 12 V to the fuel pump directly, thereby checking its performance.
37 (30 a) - ABS control unit. See 34.
38.39 - Diode nest.
40 (30 a) - heater fan (stove). See 8.
Fuses in the salon
A block with fuses is located in the cabin and placed at the bottom, the driver's left foot.
1 (10 a) - turn signs. If the turn signals stopped working and none of them light up, check in addition to this fuse, also relay 10 in the salon block and the relay installed separately at the helm. If the relay is collapsible, you can remove the case and check the fee on the absence of burnt tracks or blackened parts. Or replace to a new one, obviously good.
Then check the steering switch, the maintenance of tracks and contacts, as well as contacts in its connectivity and wiring. You should also check the lamps that could burn everything at once. If only one turn signal does not work, most likely the thing is also in the lamp. Replace in good condition and check the contacts in the connector.
2 (10 a) - ABS, control lamps On dashboard. If ABS does not work, see 34.
If the lamps do not work on the panel, check this fuse, the lamps themselves and wiring.
3 (10 A) - Devices on the panel. If you stopped working the dashboard, the part of the instruments is working, and the part is not, most likely the case in contacts on the panel board, or connectors. If this fuse is whole, try moving the connectors on the back of the panel. Check the contacts in them and wires. It may be necessary to shoot and disassemble the entire panel to get to the boards inside it. The fees should be inspecting that they do not have broken or burnt tracks and other visible traces of short circuit, lack of contacts.
4 (15 A) - Airbags. If you have worked at least one airbag, then for the previous security level, you will need to replace the opening pillow module, the SRS control unit and belts. The driver's pillow is in the center of the steering wheel, passenger - above the glove.
5 (10 A) - Engine control unit, lamps rear stroke, automatic control unit.
If you have problems with the engine, see information about fuse 4.
If when you turn on the PPC on rear transmission The reverse lamps do not light up, check the lamps themselves and their connectors, then the reverse switch, which is located on the gearbox at the top and the wires coming from it. To get to it, you need to remove the battery and air filter. Through the obtained space, access to it will open. Replace the new or repaired old if it has failed.
Location of the reverse sensor on the gearbox
6 (10 a) - central locking, electric door lock. If only one door stopped closing or open, check the castle's electric drive so that it is working and did not start, and there was also a sufficient amount of lubrication. The case can also be in the actuator (block with a board) or relay inside it. The actuator is in the door, it looks like a small box. It gives a short-term voltage of 12 V on the electricity of the desired polarity (one polarity on the opening of locks, the other on their closure).
Appearance of the door actuator block
7 (10 A) - Alarm. If a "accident" stopped working, check in addition, the fuse 2, the ribbon of the button and its contacts, wiring, as well as the lamp themselves.
8 (10 a) - stop signals. See information about fuse 2.
9 (20 a) - rear window heating. See 2.
10 (10 a) - Electric windows, winding relay block headlights, headlight washer, air conditioning heat exchanger fan, cooling radiator fan, fog lights (front and rear).
If windows do not work, see 33.
If fog lights do not work, see 14.
If the radiator fan does not work, see 6.
11 (20 a) - wiper and washer windshield . If the "wipers" do not work, check in addition to this fuse, relay 5. If they are good, most likely the case in the motor or the wiper mechanism. The motor is fastened on the back wall of the engine compartment in the direction of the right side, near the shock absorber.
It is possible to disassemble the entire mechanism, a trapezium, check the service of the motor, feeding the voltage 12 V on it, inspect all the thrust and connections, clean and lubricate WD or similar lubricants and moving parts, then collect all the mechanism and re-check the work of the "janitors". If the mechanism of the cleaner is old, some parts could "fuck", in this case the best option There will be a replacement of the whole trapezium assembly. Its minimum price - within 500-1000 rubles.
12 (10 a) - heated seats. If you stopped working seats heating, check the contacts in the seat connector, as well as the wiring and the power button. Sometimes it can be in the heating elements inside the seat, which could break the wires.
13 (10 A) - ABS. See 34.
14 - Reserve.
15 (15 A) - cigarette lighter. If the cigarette lighter stops working, check this fuse, the mustache inside the socket so that they do not close and were in their places. If the fuse cuts into the socket when inserting a connector, most likely you connect a poor-quality device with a non-standard connector that closes or deforms contacts. Check also the contacts and wires at the cigarette lighter socket under the panel. There must be a voltage of 12 V.
16 (10 A) - Mirror electric drive. If one of the mirrors ceased to be adjusted, it is possible in the button or its contacts. Check also that the mirror mechanism does not fall out of foreign objects and there was no ice. Try neatly moving his hand. Check the wiring and connector, for this you need to remove the trim and corner on the mirror.
Motor mechanism in the disassembled rearview mirror
17 (10 a) - air conditioning. If the air conditioner does not work, see 12.
18 - reserve.
Relay in the salon
The relay unit is located in the cabin of the car and is behind a small non-stale drawer.
1 - EBD brake force distribution system relays.
2 - Relay rear fog lamps.
3 - Main engine control system relay.
4 - Head light relay. See information about the fuse 3.
5 - Label and windshield washer relay. See information about the fuse 11.
6 - ABS relay. See before. 34.
7 - Relay of electrical windows. See before. 33.
8 - Rear Glass Heating Relay. See before. 2.
9 - Sound Relay. See before. 2.
10 - Relay of turns of turns, alarm alarm. See before. one.
Schemes of connections
Wiring harness scheme laid by body
 |
Connection Scheme Stop Signal Lamps
Fuses and relays HYUNDAI ACCENT in the system of heating, ventilation and air conditioning
1 - meals +12 in
2 - Power +12 V, Main engine control relay Included
3 - Power +12 V, Ignition Included
4 - Fuse Block and Relay (Motor Compartment)
5 - Salon Fuse Block
6 - fan fan stove
7 - Air Conditioner Compressor Coupling Fuse
8 - fuse electrical windows, winding relay block headlights, headlight washer, heat exchanger fan conditioner conditioner, radiator fan, front and rear fog headlights
9 - Fan Relay Stove
10 - connector
11 - to the headlight washer relay
12 - Air Conditioning Compressor Coupling Relay
13 - connector
14 - to the salon block relay
15 - ACP control unit
16 - Salon Fuse Block
17 - Air conditioner fuse
18 - Motor fan stove
19 - Engine Control Unit (ECU)
20 - from the pads on the wiring harness of the dashboard
21 - Motor Resistor Fan Stove (Heater Operation Modes)
22 - Switch operating on pressure
23 - Air conditioner switch
24 - air conditioning compressor coupling
25 - from the pad on the wiring harness of the dashboard
26 - Stove Roll Switch (Heater Fan Operations)
27 - Thermal switch
28, 29 - to the shoe on the wiring harness of the dashboard
Electrochemis car Hyundai. Accent is a collection of color schemes in Russian electrical equipment of the Hyundai Accent car since 2000 release. The relay and fuse block is shown, as well as some other modules.
Scheme of the ignition system and determining the velocity of the car
Electroscheme management of automatic transmission
Hyundai Accent.
Diagram for turning on automatic transmission
ABS Connection Scheme
Connecting control pointers
Hyundai Accent.
Windshield Character and Washers Block
Diagram of locking electric drive doors
Electric windows Hyundai Accent
Mirror Mirror Scheme and Heating Block
Enabling outdoor lighting - scheme principal
Car Headlight Regulator - Electrical Scheme
Audio Scheme Accent
Electric Sound Signal Scheme (Classone)
Turn and Alarm Pointers - Connection
Overall light and lighting lamps
Hyundai Accent.
Rear lights and fog
Brake and reverse lamps - connection in the diagram
Highlighting trunk and car interior
Conditional designations on electric hammers
Legend on electrical circuits
1 ... Rechargeable Battery
2 ... ignition switch (lock)
3 ... Starter Hyundai Accent
4 ... Generator
5 ... Box of fuses under the hood
6 ... Fuse Block / Relay / Multitimemer Front Panel
7 ... Beep Button / Headlight Switch
a - starter switch
b - Overall lights / headlights
c - Front fog lights
d - flashing by headlights
8 ... Cooling Fan Fan Switch
9 ... Motor fan cooling system
10 ... Cooling System Fan Resistor
11 ... diagnostic connector
12 ... Block relay under the hood
a - starter relay HYUNDAI ACCENT
b - Injection system relay
c - cooling system fan relay
d - relay low cooling system fan
e - Relo Steering Relay
f - Heating Relay fuel filter
g - atmospheric pressure relay
15 ... Electrical Pump Steering Amplifier
16 ... security system control unit
17 ... pretensioner of the passenger seat belt
19 ... driver airbag
20 ... Passenger Airbag
21 ... Beep Button / Headlight Switch
a - beep
b - Overall lights / headlights
d - rear fog lanterns
e - Pointer of rotation
22 ... beep
23 ... Cigarette lighter
25 ... Heater Fan Node
26 ... Heater Fan Switch
a - Switch Hyundai Accent
b - Air conditioner switch
c - Circulation Switch
d - rear window heating switch
e - Rear Wind Heating Indicator
f - Recycling Indicator
g - air conditioner indicator
27 ... Salon Lighting Reostat
30 ... air conditioning control unit
31 ... three-function air conditioner switch
32 ... air conditioner coupling
35 ... instrument panel
a - fuel level pointer
b - Immobilizer Indicator
c - Injection System Indicator
d - battery emergency charging indicator
e - Fuel Reserve Indicator
f - emergency temperature indicator
g - Emergency Fall Indicator Oil Pressure
h - Rear Fog Light Indicator
i - indicator of fog headlights
j - Right turning indicator
k - Left turning indicator
l - Middle Light Indicator
m - Far Light Indicator
n - safety belts indicator
r - open door indicator
s - Device Lighting
t - temperature pointer
u - Brake Pad Wear Indicator
v - ABS indicator
w - Brake System Fault Indicator
x - Tachometer
y - Hyundai Accent Speedometer
z - oil level index
a1 - on-board computer
36 ... Fuel pump / fuel level sensor unit
37 ... Oil pressure emergency drop sensor
38 ... Safety belt sensor
39 ... Temperature sensor / emergency temperature increase of coolant temperature
40 ... Wear Pad Wear Sensor
41 ... Sensor emergency drop in the brake fluid level
42 ... parking brake lever position sensor
43 ... oil level sensor
44 ... Switch of Wiper / Water Materover
a - Dumping computer reset button
b - Windshield Cleaner
c - Rear window cleaner / washer
d - windshield washer
46 ... ABS control unit
47 ... Left Front Wheel Sensor
48 ... Right Front Wheel Sensor
49 ... Sensor of the left rear wheel
50 ... Sensor of the right rear wheel
51 ... hours / outdoor temperature pointer (depends on the level of configuration)
52 ... Watch / Outdoor Air Index / Audio Display (depends on the configuration level)
53 ... node of the outer mirror from the passenger side (outdoor temperature sensor)
54 ... Left overall lights
55 ... Right overall lights
56 ... Left headlight
57 ... Right Headlight
58 ... Left Rear Lamp
a - rear overall fire
b - Reverse Lamps
c - HYUNDAI ACCENT STOP signals
d - rotation signs
e - Fog lights
59 ... Right Rear Light
a - rear overall fire
b - Reverse Light Lamps
c - Stop Signals
d - rotation signs
60 ... Lighting license plate
61 ... Left Front Fog
62 ... Right Front Fog Headlight
65 ... top stop signal
66 ... Rear Light Switch ( mechanical box transmissions)
67 ... automatic transmission module
68 ... control unit automatic box Transmissions
69 ... Stop Signal Switch
70 ... Left turn sign
71 ... Right turning pointer
72 ... side repeater of the left turn sign
73 ... Side Repeater Right Running Pointer
74 ... emergency signaling switch
75 ... Controlling the headlight bar
76 ... Motor of the left headlight light corrector
77 ... Motor of the right headlight light corrector
80 ... Infrared Radiation Receiver (if provided)
81 ... Lighting of the luggage compartment
82 ... Lighting Lighting Switch
83 ... Front "Polite" Lighting
84 ... switch in driver door
85 ... switch in the passenger door
86 ... switch in the left rear door
87 ... Switch in the right rear door
88 ... Windshield Purifier Motor
89 ... rear window cleaner motor
91 ... Materom Ferrous Pump
92 ... Plant Plant Owl Relay
93 ... rear window heater.
Free collection of color schemes in Russian Hyundai Accent (1.5i) car electrical equipment since 2000. The relay and fuses are shown here, as well as some other modules. Continuation of the catalog of schemes. The fuses serve in order to break the chain when the current reaches a certain value in order to protect the elements and wires that may be damaged too strong. A sharp increase in current force is usually caused by a malfunction in the chain, most often a short circuit. The designations of the chains protected by fuses are shown on the cover of the fuse block.
Before removing the fuse, turn off the appropriate chain, then remove the fuse from the contacts. Inside the fuse should be seen wire; If the fuse blocked, the wire will be torn or melted. Always use the fuses of the required power. Never use the fuse of another power and do not replace it with something else. Do not replace the fuse more than once, without removing the source of the fault. The current protected by the fuse is indicated on top of the fuse: Please note that the fuses have different colors to facilitate identification. If the fuse burns immediately after replacing, do not replace it again until you install and do not eliminate the cause of the fault. In most cases, the cause of the malfunction is a short circuit caused by poor insulation. If the fuse protects several chains, try to find the chain, due to which the fuse braves, including each of the circuits in turn (if possible). Always have a set of spare fuses in different power in the car. They must be fixed at the base of the fuse block.
If you think that the connection is not in order, disassemble the compound and determine the contact surface and the wire terminal or the surface of the ground item. Remove completely dirt and traces of corrosion, then with a knife, remove the paint layer in order to obtain a reliable metal compound with metal. When assembling, securely fix the connection; When installing the wire terminal, use gear washers between the terminal and the body. After connecting to prevent corrosion formation, apply for a layer of vaseline or silicone lubrication.
Fuses and relays Hyundai Accent
Mounting block relay and fuses in the engine compartment
1 - fuse 100 a generator circuit; 2 - fuse 50 A complex (door blocking circuits, emergency alarm, braking signals, rear window heating, sound signal, interior lighting lamps, ECU); 3 - fuse 30 a chain of lamps of head and overall light; 4 - fuse 20 A motor control circuit circuit; 5 - Fuse 30 A engine start circuit and ignition coils. 6 - Fuse 20 amp of the engine of the engine cooling system radiator, 7 - electrical wiring connector, 8 - heater fan relay. 9 - sound signal relay, 10 - fuse 10 a chain lighting lamp lighting salon hindai accent. 11 - Fuse 10 a chain of the header of the System System Reproduction. 12 - Relay 2 air-conditioning heat exchanger fan, 13 - air conditioner compressor clutch relays, 14 - fog-headlight relay socket; 15 - backup fuse jack; 16 - fuse 15 A of the idle regulator and the camshaft position sensor. 17 - fuse 10 A motor control circuit. 18 - engine cooling radiator radiator relay; 19 - fuse 10 A circuit on the air conditioner; 20 - Relay 1 air conditioning heat exchanger fan; 21 - fuse 10 A Engine control unit circuit, 22 - fuse 10 A Coupling chains of the air conditioner compressor, 23 - fuse 10 A sound signal circuit; 24 - Fuse 15 A circuit of protochemical headlights. 25 - Fuse 10 A chains of the right lamp of the head light. 26 - fuse 10 a chain of the left lamp of the head light; 27 - fuse 10 A chain chains of the overall light of the right side of the car; 28 - Fuse 10 A chain chains of the oven light of the left side of the car; 29 - lamp relays of overall light; 30 is a resistor of the pre-excitation of the generator; 31 - Starter Relo Hyundai Accent, 32 - Fuse 20 A Cynditizlimirian Condenser Condenser Fan Condenser Fan Chains, 33 - Prepalar 30 A Chains of Power Supplies. 34 - Fuse 30 A ABS control unit circuit; 35 - the nest of the relay of constantly included near light; 36 - relay of the fuel pump; 37 - fuse 30 a ABS control unit circuit; 38.39 - diode nest; 40 - Fuse 30 amp of the heater fan chain.
Block relay in the cabin car
Hyundai Fuse Installation Block
Location of wiring harnesses in Hyundai Accent
Auto electrical equipment schemes
Power Module
Connection Scheme with Mass
ELECTROMEME ENGINE OF ENGINE HYDENA ACCENT
Scheme of the compounds of the generator and cooling system
Car motor control system
