How to secure your car from the hijacking? Today, this question worries every motorist, and therefore the range of security systems offered to help him is constantly expanding. What to make a bet? On attractive characteristics or budget value? Alarm Starline A9 eliminates the owner of the machine from making a decision (it successfully combines both the first and second).
Protection 100%
The automotive system for the protection of this model is rightfully considered one of the best. And there is reason: a high indicator of the degree of protection. Such enviable safety is due to two moments:
- Complex original encryption principle. It is he who is based on a dynamic code, reliably protected from interception. Hacking an individual cipher is practically unrealistic (but the manufacturer decided to progress and strengthen the effect using a non-standard solution).
- An extraordinary innovative approach. This model of auto alarms is successfully applied and the principle of zoning. Each individual plot is guarded (DVS, parking brake, hood, doors, trunk, windows, ignition castle). And for it corresponds to a specific device (switch, sensor, relay). All information about trying to hack or cause harm is displayed on the alarm key chain. Alarm signals are included when exposed to any of the above zones.
The impeccable work of protective functions is also due to the fact that the state of all elements of the system is constantly under control. The failure of one of them is diagnosed by the device itself in a matter of seconds (the owner of the car learns about an existing problem immediately after their detection). This option (self-diagnostics) completely eliminates any risks (provided that the motorist will take the necessary measures to eliminate them in a timely manner).
Comfort class "Lux"
Another advantage of the STARLINE A9 alarm is to combine its ability to combine pleasant. It is replete with options that greatly facilitate the life of the owner of the machine, and at times increasing the degree of its comfort during operation vehicle. To such decent attention features of this model security system You can attribute:
- Autostart. Runs the engine at a certain time (the setting can be produced in three directions: depending on the temperature mode, the waiting timer, the alarm time)
- Anti-Frame mode. It triggers when, after opening a driver's door, confirmation of the displayed cipher of the owner, through a given number of meters the system blocks the engine operation.
- Immobilizer mode. Relevant for those who forget to step by step press the buttons on the keychain, is activated after 30 second lack of actions from the driver (blocks the motor after half a minute after the ignition is turned off).
- GSM Module Starline. Allows you to control the alarm from your mobile device, as well as receive messages about the state of the system.
- Indication. The alarm keychain can replace the clock, and alarm clock, and a timer, he will also inform the engine time (such information may also be needed by motorist).
This is not all the possibilities of this model, the table shows only the most sought-after from them.
Cares and energy efficiency. Situations when the keychain does not respond to the commands of his host most often associated with the wear of its power elements, in the Star Line A9 panel of the batteries serve at least 2 months (more often to six months).
Installation without problems
Automotive alarms of this brand and the model are good and the fact that they can be installed independently. This process can be characterized as complicated and simple at the same time. The difficulty lies in the fact that it involves a large amount of work, which must be implemented in accordance with the strict algorithm of actions regarding:
- location and fixation of system elements (Recommendations: The central unit is desirable to secure under the dashboard, the transceiver module on lobby glass, shock sensor anywhere in the salon, LED indicator near instruments, temperature remote sensor on the motor housing, siren in open space shore down away from highly heated parts of the engine);
- connection schemes(Wire gaskets, installation of electrical wiring connections, connecting the circuit responsible for the operation of sound and light equipment, systems with auto start, doors activator, locking system, lock engine lock, engine control over one of the options: tachometer, voltage on-board network, generator).
Easy to install Starline A9 is that the instruction manual is included in each implemented product of this type, gives a clearly detailed view of everything that concerns its installation. It can also find a description of the reasons that can lead to incorrect. unstable work Installed security system (errors made during the installation process).
Setup without much effort
All of the owners of the cars, which establish the alarm of this model, are interested in two important questions: how to tie a key chain to the system and how to configure the desired parameters for each of the modes offered by the manufacturer. To help car enthusiast detailed instructionsconcerning its interests:
- Binding keychain. We act step by step:
- we bring the car;
- press the "Valet" button (Before the appearance of 4 sound signals, we hold it);
- at the same time, press the buttons 1 and 2, release after 1 audio signal (to program the keychain with the LCD display - the main PU);
- simultaneously press the button 3 and 4 (relevant to record additional keychains).
- Programming parameters. We follow the next action algorithm:
- press 6 times the service button when the ignition is turned on (We will make the response of the system: 6 flashes of LEDs + 6 audible signals);
- press the "Valet" button several times. (before going to a specific function);
- select the desired value, confirm the action either short or long pressing the buttons 1 and 2 (half a second or 30 seconds);
- returning to "Start"by pressing the service button;
- repeat actions for all functionsin need of special settings other than factory parameters;
- we leave from programming mode (turn off and turn on the ignition or wait for an automatic shutdown, accompanied by 5 outbreaks overall lights).
Convenient management
In order to competently manage the automotive security complex called Starline A9, you do not need to have a special education. The key chain with the LCD display is a kind of book with pictures, you just need to choose the right picture. Another thing is an optional control panel (push-button panel may puzzle). However, the instruction manual included in the alarm summary For use, the task of the motorist will be simplified. These carriers crucial information Will help you find answers to all questions. There are all: connection schemes, mounting cards, methods of binding and controlling control panel (keychain), programming methods of options and parameters, and even a list possible faults and their removal techniques.
The virtues of Starline A9 is enough. Why not take advantage of them!
Every year, all new alarm models for the car appear on the market, radically different from previous models for internal functionality. The exception did not become the StarLine A9 product, which has new software settings and additional options.
Equipment
ATTENTION! Found a completely simple way to reduce fuel consumption! Do not believe? Auto mechanic with 15 years old also did not believe, until he tried. And now it saves 35,000 rubles per year in gasoline!
The company won confidence due to the fact that it makes the most complete equipment sets and guarantees a light and simple installation. In particular, in the package starline alarm A9 includes:
- 1 keychain with LCD display;
- 1 Additional keychain remote control;
- processor block;
- module with antenna;
- various sensors for installation (engine temperature, hood and other);
- manual for use and warranty card.
What is noteworthy, additional keychain of remote control car is coming without feedback. Most often, it is resorted to its use in case of loss of the head. It has only 4 buttons that serve to open-closing the doors and start the engine.
According to experts, Starline offers its customers maximum car protection with a set of additional features (timer, alarm clock, autorun, panic modes, etc.) at affordable prices.
Control in three buttons
The control key chain has a display on which you can easily consider all the characters even with bright sunlight or in complete darkness. When you click on a specific button, you can turn on the screen backlight for the convenience of viewing.
An instruction manual for the STARLINE A9 alarm is simple, since programming is only in setting the three buttons located on the upper surface. All of them have a different functional significance both separately and in a certain combination. The first button closer to the antenna allows you to program the following functions:
- admission to programming all major commands;
- running and stopping the engine (remotely);
- staging a car for protection with the engine running.
The second button, located in the middle, allows you to program the current position of the cursor on the key chain and the trunk opening command.
The third button, the most distant from the antenna, has four commands and mainly they have the functions of an additional service. Their description is as follows:
- control cursor on key chain;
- interrupting sound alert signals;
- changing modes in alarm clock and timer, clock setting and power saving mode;
- programming a button.
Understand the keychain management is easy, the main thing is initially when you buy the optimal value for the owner and change them only in certain situations. For example, the car warming timer is absolutely not needed for summer time, and in the winter it is a sharp need.
Combinations from buttons
In addition to the fact that each button is programmed separately and sets a specific function, you can configure key fob with key combination. In the STARLINE TWAGE A9 alarm, the instructions for using which comes in the kit gives full programming information, there are many interesting modes.
The combination of buttons 1 and 2 allows you to adjust panic modes, as well as a car search. The essence of the panic mode is controlled by the alarm response.
For example, this mode may be useful in that situation when the owner found suspicious personalities near his car. By pressing the button triggers a sound siren, repeating ill-wishers. This is one of the simplest programmable panic modes, and there are up to three in the STARLINE TWAGE A9 key chain.
The combination of buttons 1 and 3 has a less simple value: it allows you to adjust the keyfilt backlight. The combination of keys 2 and 3 can configure the timer on the communicator if necessary.
Advantages and advantages of the model
Each new model Alarms appearing on the market should be surprised by buyers and have new features, otherwise there will be no interest in purchasing it. Thus, STARLINE A9 alarm has the main advantage - intelligent motor autorun. And also, among the important advantages of this model, the following advantages include:
- many sensors (doors, hood, impact and other elements);
- communication with the machine within a radius of up to 600 meters due to 128 radio channels;
- the ability to start the engine from a mobile phone (with the appropriate setting of specialists).
Starline A9 carnage is inserted by AAA type battery. The validity period directly depends on the frequency of use and many other factors, but on average - from 3 to 6 months.
The equipment has a dynamic control code, that is, protection against selection and interception. Thanks to such parameters, the safety of the vehicle goes to a completely new level.
16.10.2018
The basic instruction attached to the STARLINE A9 signal contains all information about its connection and operation. How to conduct a setting, the instructions also said. The tips that are formed on the basis of feedback will be listed here. It will also be indicated how to quickly configure the main keychain to start using any of the options. You can connect an alarm with auto-start or without, as well as apply either not to use blocking. In all cases there will be several options. By the way, here we are talking about one model - Starline Twage A9, and not a9 dialog.
How to implement autorun
Let's see what is provided in the basic instruction attached to the Starline A9 signal.
Scroll of power connector
The six wires indicated above are connected to the ignition lock terminals. For example, the "red" cord is connected to the 30th terminal, on which the "+12" voltage remains all the time. And the 15th terminal receiving the potential when turning the key must be connected to the "yellow" wire. Last requirement is always observed, even if you perform installation without autorun.
Wiring power connector
Immediately list, what all cables are connected:
- Red - lock terminal 30;
- Yellow - Terminal 15 (ignition);
- Blue - lock terminal, voltage on which is missing during the starter operation, but appears when the key turns to the ACC label;
- Green - can duplicate the yellow or blue wire, and the first option is chosen by default;
- Black and white - included in the gap of the starter cable, connecting the cord of the signaling with the terminal 50;
- Black and yellow - starter nutrition.
"Blue cord" is usually connected to the "15/2" terminal to feed the second ignition line. If it is missing, you can serve a current into the accessory chain. It all depends on the standard scheme - the auto alarm is compatible with any of them.
When the start of the autorun is performed, the signaling emulates the behavior of the standard lock. But some lines, such as the power of accessories, is not necessarily connected. But the starter must receive the power in any case:
Sparking lock terminalsIf it is known that the autorun does not use the owner, connect only one wire - "yellow". We need a turbo-timer - add a "red" cord here. In the second case, all compounds must withstand a significant current (up to 30 A). In the first version, this requirement is missing.
Installation of signal chains
If everything is done, as indicated above, you can not start the motor motor. The car alarm must "know", whether the car is in the parking lot, and it is also desirable that the engine operation is controlled. By connecting only the brake ender, you can observe the following: the sound of the starter operation appears, and then the motor will start and stalls. The fact is that you still need to install a commander. Three wires that are listed here are mainly connector:
- Black and red (3) - managing a cross;
- Orange-violet (16) - monitoring the state of the brake pedal or the "handler";
- SERO-Black (6) - Engine Control Input: The cord is connected to a delivery or to the terminal on which the potential "+" appears when starting.
Note that the third cord can not be connected to anything, and then it is not even necessary to perform programming.
In the last option, the car alarm "monitors" for the voltage of the network, controlling the operation of the motor on it. But the instructions say that such a method is the most unreliable. It is better not to use control during operation at all, assigning the option 6 to 3.
Unlike most car alarms, the STARLINE TWAGE A9 system recognizes only the presence of the "mass" potential, if we talk about the brake control input. So, in the basic scheme is better to add a diode:
The resistor extends the excess voltage, and the condenser makes the signal symmetrical. In standard instructions, these details are not considered.
Connect the cord in the gray-black shell or to the generator terminal, or to the delta. By default, the second option is specified in the settings - "Danger".
Of course, the STARLINE A9 system can control the bypass. The coating relay winding is connected as follows:
- Black and Red Cord - Minus Power Supplies;
- Terminal 15 - "Plus" supply voltage.
This option, as the only correct, is specified in the basic instruction. Suppose the motor will start "once" or stall immediately after launch. Try then to connect the winding not to the 15th terminal, but by the 30th. The essence of the last sentence is clear: Alarm can enable ignition later than you need. Immobilizer will then not perceive the presence of a key.
Trial launch
If the signaling is installed, the engine test starts. Make sure that:
- PPC selection loop is cut if the system was installed on a car with MCP;
- Connecting the brake sensor for machines with MCP produced according to the circuit - the wire is connected to the "handler" button;
- Even for machines with "mechanics", preparation is carried out, then performed during operation.
The test looks simple: taking the main key chain, press the key 1. Pressing duration - 3 seconds.
The sound of the working starter will appear, but the main thing is not in this! The keychain should display the smoke icon.
Turn off or turn on the motor can be single and the same key. Note that after stopping the engine, the icon should disappear. If the condition is not fulfilled, it is impossible to use autorun. By the way, the system can not work correctly if "training" was not conducted. What is true for one option - control by the dress.
Consider how the preparation procedure looks like:
- Involve "handbrake" without turning off the ignition;
- The key is made (the engine is working);
- In 30 seconds leave the salon and closed the doors;
- The motor will stall when half a minute after step 2.
Let one of the conditions: the sound of the working motor changes either the engine stalls until step 3. It is possible to correct the situation: when programming the function 15 is assigned to 2 or 4. Then between the steps 1-2 another action will be added between the steps 1-2. Taking a key chain, you will need to press button 1, without releasing it to a melodic signal.
Note that any of the additional keychains in this case Not suitable.
Each key chain, on which there is no display, is equipped with one key that allows you to perform remote launch. The button is indicated by number 2, and you need to press it half a second.
Connecting the temperature sensor - error
If we talk about the STARLINE A9 alarm, it leads to the temperature control:
- If an external sensor is connected, the engine temperature is controlled, and the keychain displays the temperature of the cabin;
- Do not connect the sensor, know that the car alarm is measured in the temperature inside its housing.
It seems the option using an external sensor is the most suitable. Connection, in turn, spend in parallel with microcopki contacts:
The button closes when opening the hood.
The above is true for STARLINE TWAGE A9, and in general for any car alarms installed additionally. Sensor itself, that is, the resistor is connected to a standard microcopder. But when operating an effect arises:
- When the hood is open, contacts are closed - everything is right here;
- Closing the hood, you can get a "plus" potential on the signal output, which is invalid.
The latter is due to the fact that in the standard microcopka scheme is connected to the lamp, which, in turn, always gets nutrition. Lamp thread has low resistance, and "12 volts" remains at the input of the signal. Well, or "almost 12".
The problem considered above has two solutions. If during operation, the light under the hood is not used, the cord is cut, which goes to the lamp:
But interference with the standard wiring is incorrect. It is better to install an additional microcal. In addition, in the StarLine A9 sets, it is always present.
Obviously, do something in accordance with the instructions. But at the same time, the features characteristic of each car are also taken into account. This rule uses, by mounting any alarm. We wish you success.
Adding blocks
Again, we present the basic scheme taken from the instructions:
Here, as you can see, one pair of contacts is used - normally closed (NZ). Interestingly, another option (HP) will be set in the processor memory. When setting, assign functions 15 The value 3. and the diagram will start working.
The starter chain rupture, as indicated in the first chapter, includes two wires from the power connector. Thus, another blocking is implemented: the alarm is not closed by contacts when the protection is involved. Bad is that blocking the starter is almost useless. Motor with hijacking "from handles".
Each car alarm can monitor and normally open contacts. But the STARLINE TWAGE A9 system, as well as other StarLine signaling to such a relay, is better not to connect. Simply, it is not always possible to start the engine. We are talking about starting "from the key."
What and how to program
For the system under consideration here, a simple settings table is suitable:
Software changed parameters The number of options characteristic of the Starline TWAGE A9 model is 16. Seven of them, as we see, are connected by autorun. To configure, you will need any of the keychains. Values \u200b\u200b3 and 4 are specified like this: the key 1 or 2 is humbered and held three seconds. This is true if the main keychain is used.
An additional alarm console is equipped with four separate keys. Of course, they correspond to the values \u200b\u200bfrom "1" to "4". Know about it.
Here is a comment on paragraph 15. Suppose three conditions:
- The signaling was installed on a car with MCP;
- Everything is connected according to the instructions;
- When removing the key from the lock, the sound motor sound changes.
If all statements are correct, use the SAFE setting. In any other case, leave an AUTO version. As you can see, everything is simple.
The above council is important in two cases: if autorun is implemented or if a turbo-timer is needed. We are talking about a timer embedded in the signaling. By the way, the latter still needs to be enabled (option 16).
By using the SAFE item, the owner will have to press the key fob button - the ignition support does not turn on. Here it was about the procedure performed during operation.
Important was considered, one list remained:
- Turning on the ignition, the Valet button is pressed 6 times;
- Ignition turn off - the sound of sirens and 6 flares of the indicator will follow;
- The Valet button is pressed 1 time, a short siren sound follows, the button is pressed again, etc.;
- Choosing an option number in step 3, set a new value, for which any of the keychains is used;
- Car alarm can return to the "usual mode": it is enough to turn on the ignition or wait 10 seconds.
That is how, not otherwise, the STARLINE TWAGE A9 system needs to be programmed.
"Training" and the meaning of its use
Suppose each of the conditions:
- The engine control is carried out at a touchscreen;
- The sound starter sounds when automatic starts stops later than the motor is started.
Only if both conditions are made, it makes sense to conduct "training". System
"Learn" to recognize idle turns. The keychain for learning will not need.
These difficulties, in theory, are characteristic of any car alarm, and not just for the Starline brand systems. So, take patience.
Below is a sequence that is not in the basic instruction:
- Ignition include, the Valet button is pumped 9 times;
- Turn off the ignition - the indicator is constantly lit;
- Perform the start of the engine "from the key";
- When idling are installed, the VALET button is set 1 time - follows 1 siren sound;
- The indicator should go out - the training is completed!
When the alarm is trained correctly, it controls the motor without errors. By the way, the connection to the tank is recommended. That is, "simplify the task", moving to control over the generator, no sense.
Use the functions of the block
Consider a simple operation: how to turn off the sound in the remote control itself. Press and hold the 1-3 keys. The display will display the MUTE symbol, the vibration signal will follow.
Station speaker inside the console
Return everything as it was possible by pressing.
Now turn on the protection without sound emanating from the siren. Here the cursor method is activated: the 3 button is swing twice, and then by pressing the same button, move the cursor over the icons. Going to the desired label, the key 2. That is how the STARLINE A9 system is controlled.
It is known that not any car alarm is equipped with a built-in timer. From which it follows that the main keychain must be kept near the antennas. But to the system discussed here, this requirement does not apply. And yet, despite all the "pluses", you warn the reader about the following: the Starline TWAGE A9 signal does not use the dialog code. Reliability and simplicity settings are two important qualities characteristic of the TWAGE family. Need resistance to hacking - go to the Dialog family.
How the new keychain is prescribed
To use remote engine start functions, you must always adhere to the safe operation of the car and this device. The STARLINE A9 key chain is easy to program if you follow the following instructions.
How to remotely disable the shock sensor
This option has several levels. You can use it as many times as you need. It will be considered during one security cycle. To carry out this action, Move the cursor on, and make two clicks with a button located on the key chain. After that, you will see this icon, and hear the sounds - sirens and keyfob melodies. This means that the first level of this sensor has occurred. To turn off the second, do the same actions. If you need to turn on this feature again, then repeat the manipulation, and the image will disappear. One signal will also sound.
How to control the central lock from the keychain when the ignition is enabled
If in this position to sequentially press the button 1, you will see how the locks close and open the locks. On the screen, the StarLine A9 keychain will appear suitable characters and. The ignition sign looks like this.
How to start the engine remotely by keychain
There are two ways, and both of them do not depend on what state is the security mode.
The position of the car will be reflected familiar to display Starline A9. Next will see - the designation of the running engine. When heating is over, the icon will disappear. There may be only four such attempts.
Engine autorun programmed for every day
You can prescribe these parameters to the same thing. necessary time. To implement this, select, and press the button 2. In case of success, you will see the image. Now it will occur every 24 hours. To disable autorun, repeat the manipulation, and this sign will fall.
How to program the autorun of the engine at temperature
These parameters are needed to warm the engine on cold days. Time and temperature are also installed. It can be repeated up to 12 times a day. You need an image. After pressing the button 2 you will see a sign. Disconnection is similar.
Alarm autorun.
It is worth noting that the autorun is desirable to install specialists, as an error can do expensive. If the usual signaling or central locking is completely able to establish an ordinary person with straight hands, then the automatic start module is quite difficult to install. When independent installation, there is no guarantee that there will be no standard electrical circuit with interference, or the module itself will work incorrectly.
Special attention is also the ability to start and control from a mobile phone. A special control program is installed on the phone and makes it possible to run a motor using a call or an SMS message to the machine number.
You can also configure the start of the engine by calling the alarm on your mobile phone or, again, the temperature drop. Also, given the possibilities of a modern phone, right from the mobile you can see where the car is located and get alerts about its departure from a certain installed zone, a report on the excess of the car or that it is trying to evacuate.
Considering all of the above, it can be concluded that the Starline A9 signaling can become exactly what every driver is looking for his car. A full range of all possible functions today and a wonderful set in the amount of unprecedented delivery reliability only spur into the choice of this particular model, and not any other signaling from the market available on the market.
The alarm provides the opportunity remote disconnection / Turns on the shock sensor in the levels an unlimited number of times during a single security cycle.
If you need to disable only the preliminary level of the shock sensor, set the cursor to the icon, press the 2 button once. An additionally icon will be displayed on the display display, the 2 siren signals and a melodic signal keychain will be displayed. The first level of the sensor will be disconnected. If you need to turn off both levels of the shock sensor, set the cursor to the icon and click 2 keyword the second time. The icon appears on the keyboard display, and 3 beeps will be performed. Both levels of the shock sensor will be disabled. If you need to re-enable the shock sensor, set the cursor to the icon and click 2 keyword the third time. The icon will disappear from the display of the keychain, and 1 beep sounds. Both levels of the shock sensor will be turned on again.
Manage the central lock with a keychain when the ignition is turned on
When the ignition is turned on, the sequential pressing of the 1 keychain will lead to alternate closure and opening door locks.
On the display keychain will be displayed icons:
When closing locks;
When opening locks.
The ignition enabled is indicated by the icon.
Automatic control of the central lock from the ignition key (programmable function)
At your request, the automatic door lock control function can be entered when the ignition is turned on and off. If this function is turned on, then when the ignition is turned off, the door locks will be automatically open.
You can program 3 castle control options when the ignition is turned on:
- castles are not locked;
- locked after 10 seconds after the ignition is turned on;
- locked 30 seconds after switching on the ignition.
Attention! If one of the doors is open at the moment of inclusion of ignition or after switching on the ignition within 10 or 30 seconds, the locking of the door locks will not occur.
Open Door Alarm (Programmable Function)
At your request, the open door alert function can be programmed when the security mode is turned off. When opening any of the doors, the dimensions will flash for 10 seconds or until the door closing.
Control service life switches
Car search mode
To search for your car in the parking lot in the dark, press the 1 and 2 keywords simultaneously.
If before that, the protection mode turned on or turned off with sound signals of confirmation, 6 siren signals and 6 outbreaks of dimensions follow. If the security mode turned on or turned off silently, then only 6 outbreaks of dimensions will follow the command from the STARLINE TWAGE A9 alarm.
In both cases, a melodic signal keychain will sound.
Monitoring car condition
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow.
On the display, the temperature is displayed in the car's cabin (for example,) and the status of the alarm protection mode, the melodic signal will sound.
Note. Temperature display scale (Celsius or Fahrenheit) is programmed.
The temperature indicated by the keychain may differ from the real value depending on the installation location of the transceiver module in the car (for example, when the module is located on the Sun, the indicator temperature value will be more real.
Call from car
To serve a call signal from the car to the alarm keychain, press the button located on the case of the transceiver module. 6 outbreaks of dimensions follow (2 series of 3 flash). The icon appears on the keyboard display, and 20-second call sound signals are turned on. To interrupt the signals and display on the display, press the 3 keychain button.
Turbotimer Mode (Programmable Function)
For turbocharged machines, a special turbotimer mode is provided, which allows you to keep the engine operation after turning off the ignition with the key for some time required to complete the turbine stop. Thanks to this algorithm, the resource of the turbine sliding bearings is preserved.
The duration of the turbotimer is programmed 1, 3 or 6 minutes. If during operation of the turbo mode, accompanied by the lighting of the LED indicator, the protection mode will be turned on with locking locking locks, then the system will turn off the ignition inputs and the shock sensor during the turbotimer. Engine locking will not happen. The engine will be stopped automatically, and the ignition zones and the impact sensor will be protected only after turning off the turbotimer mode. The LED will start slowly flashed.
Attention.
Control of the health of end switches of car alarm STARLINE TWAGE A9
In the alarm, it is possible to control the health of the end switches of the doors, the hood and trunk when the security mode is turned off. Opening the doors, hood and trunk when the ignition is turned on, must be accompanied by flashes of the LED indicator. If the LED does not light up when they open, it means that the corresponding terminal switch is faulty.
Monitoring the condition of the car and temperature in the cabin
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow. On the display, the temperature is displayed in the car's cabin and the status of the alarm protection mode, the melodic signal will sound.
Note. The temperature displayed on the display of the keychain may differ from the real temperature in the cabin as it depends on the installation site in the car of the transceiver module (for example, when the module is in the sun, the indicator temperature value will be more real).
Service mode Valet.
To temporarily disconnect the anti-theft and security functions of the Star Line A9 car alarm, for example, when transferring a car to a service station for prophylactic or repair work, it is recommended to enable Valet service mode.
Before switching on the VALET mode, make sure that the previously programmed modes of the turbotimer and the immobilizer are turned off. Otherwise, log in to the programming mode and setting the alarm and switch the specified modes to the state - off.
To enable the service mode, set the cursor to the icon and click 2 keychain. The confirmation will follow 4 of the siren signals, 4 outbreaks of dimensions and sound a melodic signaling signal. A flashing icon appears on the display, when the Valet mode is enabled, only the remote control function of the locking and unlocking the locks of the door and control of the additional channel No. 1 (unscrupping trunk) continues.
To turn off the service mode, set the cursor to the icon, press the 2 keychain button. keychain The confirmation will follow 3 Siren Signals, 3 outbreaks of dimensions and a melodic keychain signal. Icon goes out. If necessary, program the disconnected modes of the turbotimer and the immobilizer again.
Control of additional channel number 1 (remote spilling trunk)
Channel number 1 (yellow-black wire) It can be activated independently of the system of the system and used for remote spilling of the trunk. If the channel is activated when the protection mode is enabled, the trunk zones and the shock sensor are temporarily disconnected.
There are two options for the inclusion of an additional channel number 1:
Option 1 - Press and hold the 2 keychain button for 3 seconds.
Option 2. - Use the 3 keychain button to set the cursor to the icon and press the 2 keychain button.
The confirmation will follow 3 outbreaks of dimensions and 3 beeps of the keychain.
When the security mode is turned off, the flashing image will appear on the display. open trunk.
With the mode of protection on the display, the keychain will appear flashing images of an open trunk and a disabled shock sensor
At the output of the channel there will be a negative impetus with a duration of 1 second - the trunk will open. If, when you activate the channel, the trunk will not open, then the indications of the open trunk and the disabled shock sensor on the display the keychain will not follow.
If at the time of the trunk closing the alarm will be in the mode of protection, then the zones of the trunk and the impact sensor will be taken under protection again after 5 seconds. The confirmation will sound 1 Siren Signal and 1 Sound Sound. Flashing outdoor trunk icons and shock sensor will disappear.
Advanced Channel Management 2 (Programmable Function)
An additional channel number 2 (yellow-red wire) can be activated regardless of the status of the protection mode by 0.8, 10, 30 seconds or before switching off by the keychain. The duration of the output signal is programmed when the system is set (Function 4). Channel can be used for remote control additional equipment car.
To turn on (off) the channel, set the cursor to the icon and click 2 keychain. The confirmation will follow 1 Siren Syrene, 1 outbreak of the dimensions and 1 sound keychain. On the display keychain displaying icon,
The icon disappears when the keychain is turned off.
Control of an additional channel number 3 (programmable function)
An additional channel number 3 (yellow-blue wire) can be activated regardless of the status of the Starline A9 car alarm protection mode. When working in the mode of protection, the channel can be programmed by two options:
Option 1 - Activation of the channel without shutting down the security mode. The duration of the channel for this option is programmed: 0.8, 10, 30 seconds or shutdown by keychain.
Option 2. - activation of the channel with the simultaneous shutdown of the protection mode and unlock all the locks of the doors. The duration of the channel for this option is fixed - 0.8 seconds.
To turn on (off) the channel, set the cursor to the icon and click 2 keychain.
When the channel is activated by option 1, the confirmation will follow 3 of the siren signal, 3 outbreaks of dimensions and 3 beeps of the keychain. When operating the channel for option 2, only 2 sirens and 2 flash outbreaks will follow.
An example of using an additional channel number 3 to implement the function of two-step unpiration of door locks when the security mode is turned off
Before using the channel number 3, to implement a two-step unlocking door locks with simultaneous shutdown of security mode, it is necessary:
- Connect the driver's door activator and the remaining doors activators in accordance with the scheme below
- Enter the programming mode of functions and auto alarm installations and program a function 10 (an algorithm of operation of an additional channel No. 3) according to option 2.
To turn off the security mode with unscrupuling only the driver's door, press the button 1 keychain. When the security mode is turned off, the keyboard display shows the icon and follow the audio and light confirmation signals.
To unlock the rest of the doors, set the cursor to the icon and press the 2 keychain button, follow 2 siren signals and 2 flash outbreaks.
Control of an additional channel number 4 (automatic lighting of glass or inclusion of "polite" interior lighting)
Additional channel number 4 (blue wire) can be programmed for two options:
Option 1 - The channel is automatically activated when the protection mode is turned off and simultaneously with the appearance of the alarms when the protection mode is enabled. The duration of the channel 20 or 30 seconds is programmed when the system is installed. This algorithm can be used, for example, to include "polite" interior backlight.
Option 2. - The channel is automatically activated only when the security mode is turned on. The duration of the channel 20 or 30 seconds is programmed when the system is installed. At the time of channel activation, the system does not respond to the shock sensor to avoid false positives. This algorithm can be used to automatically raise the glasses when the protection mode is turned on.
LED signaling status indication
In various signaling modes, the LED indicator flashes in different ways. If you do not have a keychain with a liquid crystal display, indicating the alarm and car status, then you can define the current signaling mode of the alarm by the type of flashing LED indicator. Types of flashing LED indicator in accordance with the signaling modes are shown in the table.
| Star Line Twage A9 Alarm Mode | Type of flashing LED indicator |
|---|---|
| The engine runs remotely | Lit constantly burning |
| Turbotimer mode included | Lit constantly burning |
| Immobilizer mode is turned on | Lit constantly burning |
| Protection mode is off | Does not burn |
| Protection mode is turned on | Slow flashes |
| Open doors, hood or trunk (with ignition on) | Quickly flashes |
| Included Mode of Daily Engine Auto Tackle or Start Budilin | Series of 2 outbreaks |
| Increased temperature autorun mode | Series of 3 outbreaks |
| Included autorun modes daily or starting the alarm clinic and temperature | 4 series of outbreaks |
| The Valet service mode is enabled. | 5 series outbreaks |
Engine starting
To implement the function of remote and automatic engine launch, at the steps of the alarm, must be programmed:
Car gearbox type (PPC) - automatic or manual. With manual gearbox, it is necessary to cut a wire loop in the central block, with an automatic gearbox - the loop must be saved.
Engine type car - gasoline or diesel (programmable function number 8). When the engine type is selected, the presence or lack of a starter is delayed after turning on the ignition at the first start attempt. For diesel engines, this delay is necessary to warm up candles before starter starter. The value of the delay can be programmed by 4, 6 or 10 seconds (programmable function No. 8).
Remote engine start can not be implemented in the following cases:
- Included ignition;
- The hood is opened;
- Parking brake is turned off;
- On cars with manual gearbox did not prepare for the engine start.
Preparation for starting the engine on cars with manual gearbox (PPC)
Preparing for the launch of the engine on cars with manual checkpoint lies in activation "software neutral"which should protect the car from the engine start when the transmission is enabled.
Turning on "software neutral" Depends on the programmed motor support mode. If AUTO mode is programmed, the inclusion is made as follows:
- Stop the car without turning off the ignition.
- Install the gear knob to the neutral position and place the car on the parking brake.
- Turn off the ignition and remove the key from the ignition lock. Engine is running.
- Within 30 seconds, leave the car, close all the doors, turn on the security mode by pressing the 1 key button. The engine will be stopped immediately or will continue to work until the turbotimer mode is turned off.
If the security mode is not turned on, the engine will continue to work for 30 seconds or turn off the turbotimer mode.
After the successful procedure described above, the car will be prepared for the start of the engine.
Attention! If after turning off the ignition according to claim 3, there is a sharp change in the idle speed of the engine or the engine stalls, it is recommended to program the SAFE engine support mode. In this case, to enable the "software neutral" mode, the actions of claim 3 must be performed as follows:
When the engine is running, press and hold the 1 channel button until 3 outbreaks of the dimensions and a melodic keychain appears. The display shows the icon and the engine operating time will display. If the turbotimemer is not programmed, the R 00 symbol appears. If the turbo-timer is programmed, the icon with the corresponding turbotimer R 01, R 03 or R 06 will appear. Now you can turn off the ignition and remove the ignition key from the lock. The engine will continue to work.
Remote Engine Start with Starline A9 alarm
There are two versions of the remote engine start regardless of the status of the security mode.
Option 1 - set the cursor to the icon and press the 2 keychain button;
Option 2. - Press the 1 key button for 3 seconds.
The first attempt to start the engine is accompanied by 3 siren signals, 3 outbreaks of dimensions and a melodic signal keychain. In the case of successful engine launch, additional 3 flash outbreaks will appear and the keychain can sound. The LED indicator will constantly light up.
On the display, the engine startup process is displayed as follows:
For one engine start cycle, the system can take 4 start-up attempts. If after 4 attempts the engine will not start, then the display shows the inscription, and the keychain will give 4 beeps, indicating the end of the start attempt. Four sirens and 4 outbreaks are followed by 4 signals.
If the engine running will stroke until the warming up time is completed, a new engine start cycle will be taken.
Note. The maximum time of the first attempt to scroll through the starter can be programmed 0.8; 1.2; 1.8; 3.0 seconds when installing alarm. The time of each subsequent attempt at the starter scroll automatically increases by 0.2 seconds.
If the engine is launched before the start of the maximum starter scroll time, then subject to the operation of the engine on the signal and generator signals, the starter will be turned off early. When controlling the operation of the engine voltage, the starter scroll time is determined by the programmed value.
Daily automatic engine start
The system has the ability to automatically start and warm up the engine at the same time (for example, every morning).
To enable the function of daily automatic start and warming up the engine, set the cursor to the icon and click the 2 button
1 Siren signal and 1 outbreak of dimensions follow. The keychain will give a melodious beep. The keyboard display shows the icon indicating the included daily autorun mode. The LED will flash a series of 2 outbreaks.
Simultaneously with the first inclusion of the function will occur automatic start Engine and its warming during the programmed time. All subsequent automatic engine launches will be made every 24 hours.
To turn off the daily autorun function, re-set the cursor to the icon and click 2 keychain. The keychain will give a melodious beep, the icon will disappear.
Attention! The unsuccessful start of the engine for any reason cancels the further programmed daily engine launches.
Automatic engine start time
Alarm has the ability to automatically start and warm up the engine with a decrease in the ambient temperature. Temperature control is carried out along the temperature sensor installed on the engine housing. Thus, the automatic start of the engine occurs when the engine temperature is reduced to -5 ° C, -10 ° C, -15 ° C or -20 ° C. Startup function, temperature value and engine warming duration are programmed. The maximum number of motor autoruns at a temperature for one day is - 12. The interval between repeated autoruns is 1 hour. The time to the subsequent launch is counting from the moment of starting the engine and does not depend on the warming time.
To enable the automatic engine start function, set the cursor to the icon and click 2 keychain. 1 siren signal will follow, 1 outbreak of dimensions, and a melodic signal keychain will sound. On the display, the icon appears the indicating power on the temperature in temperature, and the temperature value in which the engine will be launched, for example, the LED indicator will flash a series of 3 flashes. To turn off the temperature of the autorun temperature, set the cursor to the icon and click 2 keychain. Follow 2 sirens and 2 outbreaks of dimensions. The keychain will give a melodic signal, the icon will disappear.
Attention! The unsuccessful start of the engine for any reason cancels further programmed automatic launches by temperature.
Automatic Starting Engine Budil
The alarm is able to automatically start and warm the engine at any set time on the alarm clock.
To enable the auto-start function on the alarm, check the current time setting on the key chain and set the desired engine start time, programming the alarm keychain to the desired time and turning on the alarm clock. The enabled alarm mode on the display of the keychain is indicated by the icon. The engine start time is calculated as the difference between the alarm time and the current value of the time. Programming an alarm clock must be considered that only dozens of minutes are taken into account for autorun in time.
Example. Current time by keychain 7:18 PM. Set time alarm clock 7:20 PM. Starting the alarm clock will occur exactly after 10 minutes.
After checking the current time and set the alarm, set the cursor to the icon and click 2 keychain. 1 Siren signal and 1 outbreak of dimensions follow. The keychain will give a melodious beep. On the display, the icon is displayed, indicating together with the icon included the autorun mode on the alarm. The LED will flash a series of 2 outbreaks.
Simultaneously with the first turning on the function, an automatic start of the engine and its heating during the programmed time will occur. If there is no need to warm the engine you can stop the engine while clicking on the 1 keychain button. Another engine start will occur during the shown on the alarm clock. The presence of a keychain in the zone of alarm at the time of autorun on the alarm clinic is not required.
Note. The engine start time on the alarm clock and the response time of the alarm can not accurately not coincide as such a autorun takes into account the time of multiple only dozens of minutes.
To turn off the autorun function on the alarm, re-set the cursor to the icon and press the 2 keychain button. The keychain will give a melodious beep, the icon will disappear.
Note. When a power transducer + 12V, the alarm does not remember the installation of the engine start mode on the alarm.
Remote Extension of Engine Operation
To prompt extension of the running engine running time by 10, 15 or 20 minutes, set the cursor to the icon and press the 2 button the required number. Each new press, accompanied by 1 siren signal, 1 flash of the dimensions and a melodic signal keychain, increases the engine warming time for 5 minutes. The maximum engine operation time can be installed 20 minutes. At the same time on the display the keychain displays the total time remaining until the engine is stopped. If in the alarm, the engine heating is programmed without time limit, then the activation of the extension function can be used to limit the engine operation. In this case, the extension of work time leads to an automatic restriction of engine operation time. The engine will work 20 minutes and will be stopped.
Preparation of the car to the movement (shutdown of the security mode without stopping the engine)
To turn off the security mode without stopping the engine, briefly press the 1 keyword button. The keyboard display shows the condition of the vehicle with the disabled protection mode and the luminous icon.
Within 30 seconds, open the door, paste the key to the ignition lock and turn on the ignition. Disconnect the parking brake. 1 outbreak of dimensions will follow. Car ready for movement.
Remote engine stop
Without shutting down the security mode
To stop the running engine without shutting down the security mode, press and hold the 1 keychain button until 4 siren signals are appeared, 4 outbreaks of the size or melodic keychain signal. On the display, the vehicle is displayed on the state of the vehicle with the security mode, the icon _ will go out.
With shutdown of security mode
To stop the running engine with the shutdown of the security mode, press the 1 keychain button twice. The first press must be long, before the appearance of 4 signals of sirens and 4 outbreaks of dimensions. The second press should be short-term. In response, 2 siren signals will follow, 2 flash outbreaks and a melodic keychain will sound. The keyboard display shows the condition of the vehicle with the disabled security mode, the icon will go out.
Recording codes Brecks
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
- Turn on the ignition.
- Press and hold the Valet service button until 4 siren signals appear.
- To record the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
- Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
- Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.
Attention!When recording new key chains, you must overwrite both old, otherwise they will be deleted from the system's memory.
Programming functions and auto alarm installations
Some functions and installations of auto alarms can be changed using a service button and a keychain without the need to access the center block. The list of functions is shown in the table below.
Programming procedure Next:
- Turn the ignition and press the service button 6 times.
- Turn off the ignition. Flash outbreaks will follow, and 6 sirens signals indicate input to programming mode will be performed.
- Press the service button the required number times equal to the number of the selected function. Each pressing of the service button will be accompanied by the lighting of the LED indicator and short beeps, indicating the number of the currently selected function. Each fifth pressing a long beep.
- For 10 seconds, press 1 or 2 keychain (0.5 sec) or for a long time (3 sec), depending on the desired state of the selected function. A confirmation will follow 1, 2, 3 or 4 short Siren sounds and a keychain, depending on the function set function.
- To go to the next function, press the service button, and then press the keyword button to set the desired function value. Repeat this procedure for all functions requiring changes.
- To exit the programming mode, step ignition or wait for the automatic system output. The confirmation will follow 5 outbreaks of dimensions.
Note. When programming an alarm with an additional keychain function of the buttons 1 and 2 of the main keychain 3 and 4 additional keychain are performed.
Programming modes using the VALET service button
Some signaling modes can be turned on or off without using remote control key chains using the VALET service button.
The list of modes is shown in the table.
Silent The table marked the factory setting of alarm.
The procedure for programming the operation modes of the alarm is as follows:
- Turn off the ignition.
- Press the VALET service button the required number of times corresponding to the programmable mode. Each press of the service button will be accompanied by the lighting of the LED indicator.
- Turn on the ignition. Sirena short signals will follow. According to the table below, the number of sirens signals can be judged by the choice of programmable mode.
- To turn on or off the programmable mode, press the VALET service button again one or twice. In confirmation of the mode, 1 siren signal follows, in confirmation of the mode shutdown - 2 siren signals.
- Turn off the ignition. 5 outbreaks of dimensions will follow, confirming the output from the programming mode.
Note. When you turn on the daily autorun mode, the engine will start immediately after the ignition is turned off. You can turn off the engine using a control keypad.
When powering + 12V, the alarm does not remember the mode setting daily launch Engine.
The STARLINE TWAGE system can be installed on cars with a battery voltage of 12V and a negative pole on the housing.
The central block is placed in the cabin in a hidden place, preferably under the dashboard - in this case the length of the connecting wires will be minimal. To prevent entering the moisture block, it is recommended to establish it in such a way as to eliminate the flow of water droplets on the wires inside the housing. Secure the block on a flat surface with screw screws or bilateral tape so as to exclude its movement during vibrations.
The transceiver module with an antenna fasten on the windshield of the car so that from the antenna to the metal parts of the body it was at least 5 cm. In this case, the maximum range of keychains is ensured. Also, when installing, it should be noted that the temperature meter of the cabin is in this module, so the module should be placed as far as possible from heat sources and avoid the sun rays on it. Otherwise, temperature testimony may differ from the real temperature of the cabin.
Remove the engine temperature sensor to secure on the engine housing under one of the M6 \u200b\u200bbolts available on the engine, ensuring good contact with the engine housing. The position of the sensor will determine the correctness of the temperature determination of the engine.
The impact sensor is rigidly fasten in the car, ensuring access to its adjustments.
LED indicator fasten the domestic location on the dashboard.
The Valet service button and the activation mode button set to the hidden, but available to the user.
When installing push-button switches under the hood and in the trunk, check the correctness of their operation. With a closed hood or trunk, the gap between the contacts in the switch should be at least 3 mm. Incorrect installation of push-button switches is often the cause of false alarms.
Conducting the wires as far as possible from the sources of electrical interference of the ignition, high-voltage wires, etc. Note that the wires do not come into contact with the moving parts of the design of the car - pedals, steering traction, etc.
Installation of electrical wiring connections must be made when the car battery is disconnected.
Attention! If the car is equipped with an air cushion or has a coded receiver, when the power is turned off, follow the instruction manual for the car or receiver.
All of all-point connections are performed using soldering and isolate well.
Connect the central unit and other signaling components to connect to cable connectors only after the installation is completed. Installation of alarm Machine in accordance with the connection scheme.
Connecting transceiver
The antenna transceiver module is connected to a five-pin connector located in the central unit under the folding lid, with a cable that is included in the alarm kit.
Connecting a two-level shock sensor
The shock sensor is connected to the central unit using a four-wire cable included in the alarm kit. Power supply (body potential) on the sensor is carried out only in the mode of protection. Sensor sensitivity in levels is regulated by potentiometers on the sensor housing.
Connecting a LED indicator
Connect the LED plug into the two-contact connector, located in the central block under the folding lid.
Connecting the engine temperature sensor
The engine temperature sensor connects to the central unit using a 2-wire cable. One of the cable wires, connect to an orange-gray wire (input of the hood key switch) of the 18-pin connector of the central unit, and connect the second wire to the car housing. Connection polarity is not important. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.
Connecting the 6-pin power connector of the central unit
Red wire (№4)
Blue wire (№2) - Output control output control, plug the ignition lock ACC terminal.
Yellow wire (№5) - Exit ignition support # 1, connect to terminal 15 ignition lock.
Green wire (№6) - Exit ignition support # 2. The output algorithm is programmed (Function 7). See "Temporary System Work Charts with Remote Engine Starting".
Black and white wire (№3) - Exit management of the starter, plug the ignition lock terminal 50/1.
Black and yellow wire (№1) - Lock control output. Connect after the ignition lock from the starter side, having previously cutting the standard wire that runs from the ignition lock to the starter.
Connecting the 18-pin Central Block Connector
Red wire (№1) - Plus power + 12V, connect to a positive battery terminal.
Black wire (№9) - Minus power, connect with car housing, ensuring good contact.
Green-black wire (№10)
Green-yellow wire (№11) - Connect to lamps of overall lights or rotation pointers. Maximum exit load current 7,5A.
Gray wire (№13) - Positive output to connect to siren. Maximum output current 2a.
Blue-black wire (№17)- Connect to the doors button switches to the housing while opening the doors.
Blue-red wire (№7)- Connect to the door button switches closed by + 12V when the doors is opened.
Orange gray wire (№18) - Connect the hood closer to the hood when opening the hood. To properly register the temperature, the input of the hood key switching switches should not have the backlight lamp connected with + 12V.
Orange-white wire (№8) - Connect the trunk to the housing to the button switches when opening the trunk.
Yellow-black wire (№15)- Negative yield of an additional channel number 1. The duration of the 1 second control signal. Maximum load current 300mA. The channel can be used to control the solenoid spilling trunk. The connection requires an additional relay. An example of a connection scheme is shown in the figure.
Yellow-red wire (№5)- Negative yield of an additional channel number 2. Maximum load current 300mA. The pulse duration of the output signal is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). The channel can be used to control the additional equipment of the car. The connection requires an additional relay.
Yellow-blue wire (№14)- Negative yield of an additional channel number 3. Maximum load current 300mA. The pulse duration of the output signal is programmed 0.8, 10, 30 seconds or before turning off the channel by a key chain ("Latch"). The channel can be programmed to implement the function of two-step unlocking door locks or to control other car devices. The connection requires an additional relay.
Blue wire (№2) - Negative yield of an additional channel number 4. Maximum load current 300mA. The channel can be programmed to connect to salon lighting or windows control module. The connection requires an additional relay.
Black and yellow wire (№4)- negative output of the status of alarm. Maximum load current 300mA. The output is activated when the protection mode is turned on, the operation of the turbotimer, the activation of the function of anti-grab, activation of the immobilizer. When remote and automatically start in the protection mode, the output is not turned off. It is recommended to use to lock the starter circuit. When connected, an additional relay is required.
Black and white wire (№12) - negative output of the status of alarm. Maximum load current 300mA. It can be used to block the engine with normally open (HP) or normal-closed (NZ) work algorithm. The connection requires an additional relay.
Black and Red Wire (№3) - negative output of the status of alarm. Maximum load current 300mA. The output is activated when the turbotimer and the engine starts. In start mode, it can be used to restore the locked engine circuits.
Orange-violet wire (№16) - Negative input of control of the status of the parking brake or the pedal of the foot brake. The lack of negative potential on this wire in the security mode will trigger alarm operation, and in the mode of running remotely or automatically engine - the engine stop. An example of a connection scheme is shown in the figure.
Serious-black wire (№6) - Input control of engine operation. Input resistance of at least 100 com. Input sensitivity - 1.0V.
Selecting a way of monitoring the engine operation (connection of the gray-black Wire alarm STARLINE A9)
Motor Control by Tank
The gray-black wire is connected to the delta. The engine start diagnostics is carried out by changing the frequency of the tip signal. On the correctness of the connection of the black and gray wire, it is possible to judge the duration of the starter after turning off the starter during the engine start and receiving the start confirmation on the alarm key chain.
For proper connection A black and gray wire starter must turn off simultaneously with the start of the engine, regardless of the programmed starter scroll duration.
Motor control over the generator
The gray-black wire is connected to the generator output, which is connected to the lamp on dashboard. Successful engine launch will be monitored by the presence of a positive voltage + 12V at the output of the generator with the engine running. When the black and gray wire is properly connected, the starter must turn off simultaneously with the start of the engine, regardless of the programmed duration of the starter scroll.
Attention! When a gray-black wire is connected to the generator output, it is used to use the quenching resistor 510 com ... 680 com.
Control of the engine voltage onboard network
In case of the difficulty of detecting the chains of the band or generator, it is allowed to use the engine start monitoring mode over the on-board network. In this case, the gray-black wire does not connect and it is necessary to isolate it. Start confirmation will occur automatically after starting the engine. The disadvantage of this method of control is the fixed starter time. For proper operation of the starter without a twist, you will need to select the necessary duration, programming the function number 3 to the values \u200b\u200bof 800, 1200, 1800 or 3000 ms.
Connecting the built-in engine lock circuit
Run the chain between the ignition lock and starter. In the chain break, connect the black and white wire of the 6-pin connector from the ignition lock and the black and yellow wire 6-pin connector from the starter side. The maximum current of the built-in lock relay is 40a.
Connecting an external engine lock circuit using conventional relays
Run one of the standard engine start circuits and connect the additional relay into the circuit break. The type of contacts of the NR lock relay (normally open) or NZ (normally closed) is programmed (function 15). Initially, the factory is programmed by the NZ Type of Relay Contacts. An example of a connection scheme of one of the chains is shown in the figure.
Connecting an external engine blocking circuit using a Universal Starline Wireless Lock Set
This method of blocking the engine significantly increases anti-theft alarm properties. To control the module included in the Universal Starline Wireless Lock Kit, use a black and white alarm wire, pre-programmed it on a normally open (HP) type of contacts. Possible engine blocking schemes are given in the installation instructions for installing the Universal Wireless Lock Starline.
Connection to Solenoid Unlocking Trudge
Alarm has an outlet for remote spilling trunk (yellow-black wire). Maximum load Exit - 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connect to salon lighting
An additional alarm channel 2 can be used to connect to the near light of the headlights and the implementation of the "Lightway" function (yellow-red wire). The maximum output load is 300 mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connecting an orange-purple wire on cars with manual and automatic gearbox
On vehicles with manual gearbox, connect this wire to the parking brake button switch, which closes to the housing when the brake is turned on.
On vehicles with automatic gearbox, connect this wire to the brake pedal button closed to + 12V when the brake pedal is pressed.
Alarm has an output that can be used to connect to salon lighting and implementing the function of the "polite lighting of the cabin" (blue wire). The maximum output load is 300mA, when connected, use an additional relay. An example of a connection scheme is shown in the figure.
Connecting to neighbor headlights
Connect to the central locking system
Starline Twage alarm has built-in central lock control relays. Relay contacts are displayed on a 6-pin connector. Load capacity of built-in relay 15a. The duration of control pulses is programmed (Function 9).
In the alarm, it is possible to remotely disconnect / turn on the impact sensor over the levels an unlimited number of times during the same protection cycle.
If you need to disable only the preliminary level of the shock sensor, set the cursor to the icon, press the 2 button once. An additionally icon will be displayed on the display display, the 2 siren signals and a melodic signal keychain will be displayed. The first level of the sensor will be disconnected. If you need to turn off both levels of the shock sensor, set the cursor to the icon and click 2 keyword the second time. The icon appears on the keyboard display, and 3 beeps will be performed. Both levels of the shock sensor will be disabled. If you need to re-enable the shock sensor, set the cursor to the icon and click 2 keyword the third time. The icon will disappear from the display of the keychain, and 1 beep sounds. Both levels of the shock sensor will be turned on again.
Manage the central lock with a keychain when the ignition is turned on
When the ignition is turned on, the sequential pressing of the 1 keychain will lead to alternate closure and opening door locks.
On the display keychain will be displayed icons:
When closing locks;
When opening locks.
The ignition enabled is indicated by the icon.
Automatic control of the central lock from the ignition key (programmable function)
At your request, the automatic door lock control function can be entered when the ignition is turned on and off. If this function is turned on, then when the ignition is turned off, the door locks will be automatically open.
You can program 3 castle control options when the ignition is turned on:
- castles are not locked;
- locked after 10 seconds after the ignition is turned on;
- locked 30 seconds after switching on the ignition.
Attention! If one of the doors is open at the moment of inclusion of ignition or after switching on the ignition within 10 or 30 seconds, the locking of the door locks will not occur.
Open Door Alarm (Programmable Function)
At your request, the open door alert function can be programmed when the security mode is turned off. When opening any of the doors, the dimensions will flash for 10 seconds or until the door closing.
Control service life switches
Car search mode
To search for your car in the parking lot in dark time Tap simultaneously buttons 1 and 2 keychain.
If before this, the protection mode turned on or turned off with sound signals
confirmation, follow 6 siren signals and 6 outbreaks of dimensions. If the mode
The protection turned on or turned off silently, then by the team from the STARLINE alarm
TWAGE A9 will follow only 6 outbreaks of dimensions.
In both cases, a melodic signal keychain will sound.
Monitoring car condition
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow.
On the display, the temperature is displayed in the car's cabin (for example,) and the status of the alarm protection mode, the melodic signal will sound.
Note. Temperature display scale (Celsius or Fahrenheit) is programmed.
The temperature indicated by the keychain may differ from the real value depending on the installation location of the transceiver module in the car (for example, when the module is located on the Sun, the indicator temperature value will be more real.
Call from car
To serve a call signal from the car to the alarm keychain, press the button located on the case of the transceiver module. 6 outbreaks of dimensions follow (2 series of 3 flash). The icon appears on the keyboard display, and 20-second call sound signals are turned on. To interrupt the signals and display on the display, press the 3 keychain button.
Turbotimer Mode (Programmable Function)
For turbocharged machines, a special turbotimer mode is provided, which allows you to keep the engine operation after turning off the ignition with the key for some time required to complete the turbine stop. Thanks to this algorithm, the resource of the turbine sliding bearings is preserved.
The duration of the turbotimer is programmed 1, 3 or 6 minutes. If during operation of the turbo mode, accompanied by the lighting of the LED indicator, the protection mode will be turned on with locking locking locks, then the system will turn off the ignition inputs and the shock sensor during the turbotimer. Engine locking will not happen. The engine will be stopped automatically, and the ignition zones and the impact sensor will be protected only after turning off the turbotimer mode. The LED will start slowly flashed.
Attention.
Control of the health of limit translation switches STARLINE TWAGE
A9.
In the alarm, it is possible to control the health of the end switches of the doors, the hood and trunk when the security mode is turned off. Opening the doors, hood and trunk when the ignition is turned on, must be accompanied by flashes of the LED indicator. If the LED does not light up when they open, it means that the corresponding terminal switch is faulty.
Monitoring the condition of the car and temperature in the cabin
Set the cursor to the icon and click 2 keychain. 3 flash outbreaks will follow. On the display, the temperature is displayed in the car's cabin and the status of the alarm protection mode, the melodic signal will sound.
Note. The temperature displayed on the display of the keychain may differ from the real temperature in the cabin as it depends on the installation site in the car of the transceiver module (for example, when the module is in the sun, the indicator temperature value will be more real).
Service mode Valet.
For
temporary disconnection of anti-theft and security functions of the STAR auto alarm
Line A9, for example, when transferring a car to the station service
for prophylactic or repair work It is recommended to include
Walt service mode.
Before switching on the VALET mode, make sure that the previously programmed modes of the turbotimer and the immobilizer are turned off. Otherwise, log in to the programming mode and setting the alarm and switch the specified modes to the state - off.
To enable the service mode, set the cursor to the icon and click 2 keychain. The confirmation will follow 4 of the siren signals, 4 outbreaks of dimensions and sound a melodic signaling signal. A flashing icon appears on the display, when Valet is enabled, only the remote control function of the locking and unlocking door locks and control of the additional channel No. 1 continues to operate.
To turn off the service mode, set the cursor to the icon, press the 2 keychain button. keychain The confirmation will follow 3 Siren Signals, 3 outbreaks of dimensions and a melodic keychain signal. Icon goes out. If necessary, program the disconnected modes of the turbotimer and the immobilizer again.
Control of additional channel number 1 (remote spilling trunk)
Channel number 1 (yellow-black wire) It can be activated independently of the system of the system and used for remote spilling of the trunk. If the channel is activated when the protection mode is enabled, the trunk zones and the shock sensor are temporarily disconnected.
There are two options for the inclusion of an additional channel number 1:
Option 1 - Press and hold the 2 keychain button for 3 seconds.
Option 2 - Use the 3 keychain button. Set the cursor to the icon and click the 2 keychain button.
The confirmation will follow 3 outbreaks of dimensions and 3 beeps of the keychain.
When the security mode is disabled on the display, the flashing image of the open trunk will appear.
With the mode of protection on the display, the keychain will appear flashing images of an open trunk and a disabled shock sensor
At the output of the channel there will be a negative impetus with a duration of 1 second - the trunk will open. If, when you activate the channel, the trunk will not open, then the indications of the open trunk and the disabled shock sensor on the display the keychain will not follow.
If at the time of the trunk closing the alarm will be in the mode of protection, then the zones of the trunk and the impact sensor will be taken under protection again after 5 seconds. The confirmation will sound 1 Siren Signal and 1 Sound Sound. Flashing outdoor trunk icons and shock sensor will disappear.
Advanced Channel Management 2 (Programmable Function)
An additional channel number 2 (yellow-red wire) can be activated regardless of the status of the protection mode by 0.8, 10, 30 seconds or before switching off by the keychain. The duration of the output signal is programmed when the system is set (Function 4). The channel can be used to remotely control the additional car equipment.
To turn on (off) the channel, set the cursor to the icon and click 2 keychain. The confirmation will follow 1 Siren Syrene, 1 outbreak of the dimensions and 1 sound keychain. On the display keychain displaying icon,
The icon disappears when the keychain is turned off.
Control of an additional channel number 3 (programmable function)
Additional
Channel number 3 (yellow-blue wire) can be activated regardless of the state
Starline A9 car alarm protection modes. When working in the mode of protection of the channel
Can be programmed for two options:
Option 1 - Channel activation without shutting down the security mode. The duration of the channel for this option is programmed: 0.8, 10, 30 seconds or shutdown by keychain.
Option 2 - Activation of the channel with simultaneous shutdown of the protection mode and unlock all door locks. The duration of the channel for this option is fixed - 0.8 seconds.
To turn on (off) the channel, set the cursor to the icon and click 2 keychain.
When the channel is activated by option 1, the confirmation will follow 3 of the siren signal, 3 outbreaks of dimensions and 3 beeps of the keychain. When operating the channel for option 2, only 2 sirens and 2 flash outbreaks will follow.
An example of using an additional channel number 3 to implement the function of two-step unpiration of door locks when the security mode is turned off
Before using the channel number 3, to implement a two-step unlocking door locks with simultaneous shutdown of security mode, it is necessary:
- Connect the driver's door activator and the remaining doors activators in accordance with the scheme below
- Enter the programming mode of functions and auto alarm installations and program a function 10 (an algorithm of operation of an additional channel No. 3) according to option 2.
To turn off the security mode with unscrupuling only the driver's door, press the button 1 keychain. When the security mode is turned off, the keyboard display shows the icon and follow the audio and light confirmation signals.
To unlock the rest of the doors, set the cursor to the icon and press the 2 keychain button, follow 2 siren signals and 2 flash outbreaks.
Control of an additional channel number 4 (automatic raising of glass or the inclusion of "polite" interior backlight)
Additional channel number 4 (blue wire) can be programmed for two options:
Option 1 - The channel is automatically activated when the protection mode is turned off and simultaneously with the appearance of alarms when the security mode is enabled. The duration of the channel 20 or 30 seconds is programmed when the system is installed. This algorithm can be used, for example, to include a "polite" interior backlight.
Option 2 - The channel is automatically activated only when the security mode is turned on. The duration of the channel 20 or 30 seconds is programmed when the system is installed. At the time of channel activation, the system does not respond to the shock sensor to avoid false positives. This algorithm can be used to automatically raise the glasses when the protection mode is turned on.
LED signaling status indication
In various signaling modes, the LED indicator flashes in different ways. If you do not have a keychain with a liquid crystal display, indicating the alarm and car status, then you can define the current signaling mode of the alarm by the type of flashing LED indicator. Types of flashing LED indicator in accordance with the signaling modes are shown in the table.
| Star Line Twage A9 Alarm Mode | Type of flashing LED indicator |
|---|---|
| The engine runs remotely | Lit constantly burning |
| Turbotimer mode included | Lit constantly burning |
| Immobilizer mode is turned on | Lit constantly burning |
| Protection mode is off | Does not burn |
| Protection mode is turned on | Slow flashes |
| Open doors, hood or trunk (with ignition on) | Quickly flashes |
| Included Mode of Daily Engine Auto Tackle or Start Budilin | Series of 2 outbreaks |
| Increased temperature autorun mode | Series of 3 outbreaks |
| Included autorun modes daily or starting the alarm clinic and temperature | 4 series of outbreaks |
| The Valet service mode is enabled. | 5 series outbreaks |
Engine starting
To implement the function of remote and automatic engine launch, at the steps of the alarm, must be programmed:
Type of car shift box (PPC) - automatic or manual. With manual gearbox, it is necessary to cut a wire loop in the central block, with an automatic gearbox - the loop must be saved.
Motor type of car - gasoline or diesel (programmable function No. 8). When the engine type is selected, the presence or lack of a starter is delayed after turning on the ignition at the first start attempt. For diesel engines Such a delay is necessary to warm up candles before starter starter. The value of the delay can be programmed by 4, 6 or 10 seconds (programmable function No. 8).
Remote engine start can not be implemented in the following cases:
- Included ignition;
- The hood is opened;
- Parking brake is turned off;
- On cars with manual gearbox did not prepare for the engine start.
Preparation for starting the engine on cars with manual gearbox (PPC)
Preparations for the start of the engine on cars with manual gearbox lies in the activation of "software neutral", which should protect the car from the engine start when the transfer is enabled.
The inclusion of "software neutral" depends on the programmed engine support mode. If AUTO mode is programmed, the inclusion is made as follows:
- Stop the car without turning off the ignition.
- Install the gear knob to the neutral position and place the car on the parking brake.
- Turn off the ignition and remove the key from the ignition lock. Engine is running.
- Within 30 seconds, leave the car, close all the doors, turn on the security mode by pressing the 1 key button. The engine will be stopped immediately or will continue to work until the turbotimer mode is turned off.
If the security mode is not turned on, the engine will continue to work for 30 seconds or turn off the turbotimer mode.
After the successful procedure described above, the car will be prepared for the start of the engine.
Attention! If after turning off the ignition according to claim 3, there is a sharp change idling The engine or motor stalls, it is recommended to program the SAFE engine support mode. In this case, to enable the "program neutral" mode, the actions of claim 3 must be performed as follows:
When the engine is running, press and hold the 1 channel button until 3 outbreaks of the dimensions and a melodic keychain appears. The display shows the icon and the engine operating time will display. If the turbotimemer is not programmed, the R 00 symbol appears. If the turbo-timer is programmed, the icon with the corresponding turbotimer R 01, R 03 or R 06 will appear. Now you can turn off the ignition and remove the ignition key from the lock. The engine will continue to work.
Remote Engine Start with Starline A9 alarm
There are two versions of the remote engine start regardless of the status of the security mode.
Option 1 - Install the cursor to the icon and press the 2 keyword button;
Option 2 - Press 1 keychain button for 3 seconds.
The first attempt to start the engine is accompanied by 3 siren signals, 3 outbreaks of dimensions and a melodic signal keychain. In the case of successful engine launch, additional 3 flash outbreaks will appear and the keychain can sound. The LED indicator will constantly light up.
On the display, the engine startup process is displayed as follows:
For one engine start cycle, the system can take 4 start-up attempts. If after 4 attempts the engine will not start, then the display shows the inscription, and the keychain will give 4 beeps, indicating the end of the start attempt. Four sirens and 4 outbreaks are followed by 4 signals.
If the engine running will stroke until the warming up time is completed, a new engine start cycle will be taken.
Note. The maximum time of the first attempt to scroll through the starter can be programmed 0.8; 1.2; 1.8; 3.0 seconds when installing alarm. The time of each subsequent attempt at the starter scroll automatically increases by 0.2 seconds.
If the engine is launched before the start of the maximum starter scroll time, then subject to the operation of the engine on the signal and generator signals, the starter will be turned off early. When controlling the operation of the engine voltage, the starter scroll time is determined by the programmed value.
Daily automatic engine start
The system has the ability to automatically start and warm up the engine at the same time (for example, every morning).
To enable the function of daily automatic start and warming up the engine, set the cursor to the icon and click the 2 button
1 Siren signal and 1 outbreak of dimensions follow. The keychain will give a melodious beep. The keyboard display shows the icon indicating the included daily autorun mode. The LED will flash a series of 2 outbreaks.
Simultaneously with the first turning on the function, an automatic start of the engine and its heating during the programmed time will occur. All subsequent automatic engine launches will be made every 24 hours.
To turn off the daily autorun function, re-set the cursor to the icon and click 2 keychain. The keychain will give a melodious beep, the icon will disappear.
Attention! The unsuccessful start of the engine for any reason cancels the further programmed daily engine launches.
Automatic engine start time
Alarm has the ability to automatically start and warm up the engine when the temperature is reduced. ambient. Temperature control is carried out along the temperature sensor installed on the engine housing. Thus, the automatic start of the engine occurs when the engine temperature is reduced to -5 ° C, -10 ° C, -15 ° C or -20 ° C. Startup function, temperature value and engine warming duration are programmed. The maximum number of motor autoruns at a temperature for one day is - 12. The interval between repeated autoruns is 1 hour. The time to the subsequent launch is counting from the moment of starting the engine and does not depend on the warming time.
To enable the automatic engine start function, set the cursor to the icon and click 2 keychain. 1 siren signal will follow, 1 outbreak of dimensions, and a melodic signal keychain will sound. On the display, the icon appears the indicating power on the temperature in temperature, and the temperature value in which the engine will be launched, for example, the LED indicator will flash a series of 3 flashes. To turn off the temperature of the autorun temperature, set the cursor to the icon and click 2 keychain. Follow 2 sirens and 2 outbreaks of dimensions. The keychain will give a melodic signal, the icon will disappear.
Attention! The unsuccessful start of the engine for any reason cancels further programmed automatic launches by temperature.
Automatic Starting Engine Budil
The alarm is able to automatically start and warm the engine at any set time on the alarm clock.
To enable the auto-start function on the alarm, check the current time setting on the key chain and set the desired engine start time, programming the alarm keychain to the desired time and turning on the alarm clock. The enabled alarm mode on the display of the keychain is indicated by the icon. The engine start time is calculated as the difference between the alarm time and the current value of the time. Programming an alarm clock must be considered that only dozens of minutes are taken into account for autorun in time.
Example. Current time by keychain 7:18 PM. Set time alarm clock 7:20 PM. Starting the alarm clock will occur exactly after 10 minutes.
After checking the current time and set the alarm, set the cursor to the icon and click 2 keychain. 1 Siren signal and 1 outbreak of dimensions follow. The keychain will give a melodious beep. On the display, the icon is displayed, indicating together with the icon included the autorun mode on the alarm. The LED will flash a series of 2 outbreaks.
Simultaneously with the first turning on the function, an automatic start of the engine and its heating during the programmed time will occur. If there is no need to warm the engine you can stop the engine while clicking on the 1 keychain button. Another engine start will occur during the shown on the alarm clock. The presence of a keychain in the zone of alarm at the time of autorun on the alarm clinic is not required.
Note. The engine start time on the alarm clock and the response time of the alarm can not accurately not coincide as such a autorun takes into account the time of multiple only dozens of minutes.
To turn off the autorun function on the alarm, re-set the cursor to the icon and press the 2 keychain button. The keychain will give a melodious beep, the icon will disappear.
Note. When a power transducer + 12V, the alarm does not remember the installation of the engine start mode on the alarm.
Remote Extension of Engine Operation
To prompt extension of the running engine running time by 10, 15 or 20 minutes, set the cursor to the icon and press the 2 button the required number. Each new press, accompanied by 1 siren signal, 1 flash of the dimensions and a melodic signal keychain, increases the engine warming time for 5 minutes. The maximum engine operation time can be installed 20 minutes. At the same time on the display the keychain displays the total time remaining until the engine is stopped. If in the alarm, the engine heating is programmed without time limit, then the activation of the extension function can be used to limit the engine operation. In this case, the extension of work time leads to an automatic restriction of engine operation time. The engine will work 20 minutes and will be stopped.
Preparation of the car to the movement (shutdown of the security mode without stopping the engine)
To turn off the security mode without stopping the engine, briefly press the 1 keyword button. The keyboard display shows the condition of the vehicle with the disabled protection mode and the luminous icon.
Within 30 seconds, open the door, paste the key to the ignition lock and turn on the ignition. Disconnect the parking brake. 1 outbreak of dimensions will follow. Car ready for movement.
Remote engine stop
Without shutting down the security mode
To stop the running engine without shutting down the security mode, press and hold the 1 keychain button until 4 siren signals are appeared, 4 outbreaks of the size or melodic keychain signal. On the display, the vehicle is displayed on the state of the vehicle with the security mode, the icon _ will go out.
With shutdown of security mode
To stop the running engine with the shutdown of the security mode, press the 1 keychain button twice. The first press must be long, before the appearance of 4 signals of sirens and 4 outbreaks of dimensions. The second press should be short-term. In response, 2 siren signals will follow, 2 flash outbreaks and a melodic keychain will sound. The keyboard display shows the condition of the vehicle with the disabled security mode, the icon will go out.
Recording codes Brecks
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
- Turn on the ignition.
- Press and hold the Valet service button until 4 siren signals appear.
- To record the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
- Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
- Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.
Attention! When recording new key chains, you must overwrite both old, otherwise they will be deleted from the system's memory.
Programming functions and auto alarm installations
Some functions and installations of auto alarms can be changed using a service button and a keychain without the need to access the center block. The list of functions is shown in the table below.
Programming procedure Next:
- Turn the ignition and press the service button 6 times.
- Turn off the ignition. Flash outbreaks will follow, and 6 sirens signals indicate input to programming mode will be performed.
- Press the service button the required number times equal to the number of the selected function. Each pressing of the service button will be accompanied by the lighting of the LED indicator and short beeps, indicating the number of the currently selected function. Each fifth pressing a long beep.
- For 10 seconds, press 1 or 2 keychain (0.5 sec) or for a long time (3 sec), depending on the desired state of the selected function. A confirmation will follow 1, 2, 3 or 4 short Siren sounds and a keychain, depending on the function set function.
- To go to the next function, press the service button, and then press the keyword button to set the desired function value. Repeat this procedure for all functions requiring changes.
- To exit the programming mode, step ignition or wait for the automatic system output. The confirmation will follow 5 outbreaks of dimensions.
Note. When programming an alarm with an additional keychain function of the buttons 1 and 2 of the main keychain 3 and 4 additional keychain are performed.
Programming modes using the VALET service button
Some signaling modes can be turned on or off without using remote control key chains using the VALET service button.
The list of modes is shown in the table.
Silent The table marked the factory setting of alarm.
The procedure for programming the operation modes of the alarm is as follows:
- Turn off the ignition.
- Press the VALET service button the required number of times corresponding to the programmable mode. Each press of the service button will be accompanied by the lighting of the LED indicator.
- Turn on the ignition. Sirena short signals will follow. According to the table below, the number of sirens signals can be judged by the choice of programmable mode.
- To turn on or off the programmable mode, press the VALET service button again one or twice. In confirmation of the mode, 1 siren signal follows, in confirmation of the mode shutdown - 2 siren signals.
- Turn off the ignition. 5 outbreaks of dimensions will follow, confirming the output from the programming mode.
Note. When you turn on the daily autorun mode, the engine will start immediately after the ignition is turned off. You can turn off the engine using a control keypad.
When a power supply + 12V, the alarm does not remember the installation of the daily engine start mode.
Greetings, dear readers of the site!
I want to tell you a story about replacing the block for the Starline car alarm.
If briefly, it works, it works, I recommend!
From recently, I started to join me on the main key chain of the alarm, it was sold and triggered one time. It was decided to disassemble and see what happened there.
The autopsy showed that due to the design curve of the buttons and the frequent use of the same button, the legs could not withstand the tension and decided to break away from the board.
The button first soldered at home, was enough for a week. Next was soldered on a soldering station with a special, more solid tin, also had a short time, fell off three weeks later.
so it turned out in the end
This button is just tied to the power on / off, so very necessary. Of course, there is a second, programmable button, with which you can also put on guard, but it is inconvenient.
Therefore, it was decided to purchase the second key chain.
I have a fairly old alarm and the original keyfobs are practically not found, and what can be found is not a fact that it turns out to be the original. + Translate price tag.
The fluid search has shown that there are key rings on Ali, but under different veiled names, it very complicated the search. For example, this seller called her Tamarack, the other was Twace, everything is looking for on the word Starline - with a horse price tag.
Also upset the fact that the keyfobs specifically for StarLine A8 are not only for A9. The officially STARLINE state reports that the key rings are not compatible, but at the same time on the profile forum the people wrote that partially compatible and there may be problems with the key fob in the signaling of the signaling, as well as some functions may not work.
A deeper google led to the conclusion that all the same key chains are compatible and basic functions work.
For A9, the choice is much more diverse (against zero for A8). I came across this lot, the price tag was one of the lowest. Of course, it was embarrassed by a small rating of the seller and a modest assortment in the store, but I took the final decision after reading one of the comments that one buyer was successfully stitched by A8. Mostly all the other reviews are good, it was decided to buy.
I ordered, paid, everything is OK. I sent the seller about the 3rd or 4th day, I don't remember exactly already.
Track with tracking. Delivery on current standards is not fast - exactly a month.
Packaging on a troeuchka, a yellow package, the key chain itself in the puppete package, unreliable however. On the way, all the puppies were pleased with mail employees, while they were thrown by my parcel. Therefore, it was worth packing better, they could have broken the screen.
The seller even put this postcard, signed himself. Again, 5 stars asks.
At the sight of a large similarity with the original, although I also can't know if I have the original, because I received a signal from the car and I don't know anything about her biography.
Differences can be reduced that after all, my key chain from A8, and this one from A9.
The case is absolutely the same, quite a bit deeper than the hole under the button and the buttons themselves are made from another material, slightly larger out of the housing.
Pictograms on the screen are a bit brighter from the new, perhaps on the old one they focused on time.
Illumination of the same color. The resulting keyfob seems a little worse the screen in quality, if you look at the top, then the badges are flexible, the old one was also, but not so much expressed.
In general, more visual differences did not find.
External comparison
Even there is a holographic sticker StarLine :) 
I stitched the key chain with a bang, works as a native. Programmatically distinguished by the A9 key chain from A8 consists only that the cursor of the programmable button 2 over time hesitates to the default position, there was no such thing on the old old one.
I stitched on this instruction:
In total, 4 keychain can be recorded in the alarm memory. Recording codes of key chains is performed when the security mode is turned off in the following order:
1. Turn the ignition.
2. Press and hold the VALET service button until 4 siren signals appear.
3. To write the main keychain with the display, click simultaneously buttons 1 and 2 keychain. To write an additional keychain without a display, press simultaneously buttons 3 and 4 keychain. Successful recording of the first keychain in the memory of the system is confirmed by 1 siren signal.
4. Repeat item 3 for all recorded keychains. The interval between the recording of each keychain should not exceed 5 seconds, otherwise the alarm will automatically exit the recording mode of the keychain. Successful recording of each keychain is confirmed by the corresponding number of siren signals.
5. Turn off the ignition. In confirmation of the output from the recording mode, 5 outbreaks of the dimensions will follow 5 outbreaks.
When I stitched new keychain, missed very much important moment, the button then on the old one is broken and it will not work it. Thus, if something went wrong, I would stay without a signal for a while, but everything went like on the oil, the new key chain was lying without any problems. Now it remains to fall the old old and flash it, it will be a spare.
Checked the main functions, accurately work:
- Removal / arming, with sound and without.
- alarm on the shock sensor 1 and 2 levels with feedback
- autorun and engine stop.
- Request information about the status of the car (temperature, whether the engine is launched, do the doors, the position of the handbrake, ignition)
- Opening the trunk on the second channel.
In the rest of the functions I do not need, so I did not check.
To whom it is interesting, for comparison, photos of the insides, on top of the old keychain, under it overlooked sabzh.
It can be seen in the naked eye that in the version A8 screen on the loop, in A9 Wpayan on the legs 
Separate fees did not, reluctant to gut a new key chain, but visually there are differences in circuitry 
And again these buttons that, I hope this time stretches for a long time. (Photo after the 3rd propios of the old key fob) 
By the time the review is published, the old keychain was released, the button started again. Both key products have been successfully recorded in the signal of the signal. Unfortunately, they do not work in a pair, that is, when the alarm is triggered, the key chain, from which they put on guard, will be silent. The status of protection does not change dynamically on both keyboards, only on the one from which you install / remove the security.
In general, they work according to the principle - who is the last, that and dad.
The goods are purchased for money and on its own initiative. If someone decides to buy a key chain from this seller, write in the comments, I will try to negotiate a discount for Muskovchan.
For Sim I speak, thanks for watching!
I plan to buy +16. Add to favourites I liked the review +24 +52
