From the details OT. washing machine, regardless of its condition and type, you can make a variety useful devices and fixtures.
They can perform various mechanical workAnd also play the role of generators of free backup energy. For the manufacture of homemade with an electric motor, the housing, wiring and other parts will rise.
Variants of devices
Below is described what can be made from the old washing machine. These devices will be useful for farm, construction, gardening and repair.
The most common homemade is emery. Since the diameters of the shaft of the motor and the grinding stone are different, it will be necessary to make a consistent adapter. His role will play a piece of 20-centimeter pipe. At the end of the last one should make a thread so that it is twice as long than the grinding stone. Its direction should be the opposite rotation of the motor. This is necessary so that the grinding circle does not unscrew and flick.
Adapter should be fixed on the motor shaft. Then you will need to drill a hole there, and screw the bolt and the nut to finally fix the emery circle with the adapter. It remains to strengthen the homemade on the reliable basis.
Motor power from a washing machine is enough for a small lathe or drum-grinding machine. In the first case, you can slowly treat the cylindrical workpiece. For more reliable consolidation, apply a support that protects the motor from excessive side loads. In the second case, the cylinder is put on the engine shaft, which is hoping for grinding paper. Inside it should also be installed a steel bar, with which you can fix on the motor shaft.
The old washing machine of the activator type can turn into a small concrete mixer. This follows:
- Make a blade, for which it is necessary to cut out of 4-5 mm steel blanks, connect at right angles (in the form of the letter P), and cook.
- Attach the item to the activator place.
- Connect the engine to the network (see below).
- It will only be left to put the necessary building materials in the tank.
- The power of the motor in this case will be sufficient for small volumes.
You can also make a bubble. In addition to the engine, a drum will be required from the washing machine. You need to make two sharpened blades playing the role of knives. The drum is attached to the support frame with bolts. In its lower part, an outlet should be done. One blade with a knife is installed on the bottom, and the other is closer to the top. On the front of the drum, it is necessary to adjust the cover so that the feed is not figured on the sides.
Another possible homemade is a lawn mower. It will work at all worse than the factory. For its manufacture, you will need:
First, it is necessary to weld the square frame with the axes. Based on which it is attached from its lower side, you should do a hole for the motor shaft, and then fasten it. Of the longer pipes, it is necessary to make a P-shaped handle. A rubber casing is put on its horizontal part to be more convenient to hold. Wire with switch connected to the motor. If you plan to use wet grass to circumcise, then you need to carefully insulate all conductive parts.
Finally, the last device that can be made from the washing machine - this is generator. Asynchronous engine will require refinement. It is necessary to disassemble it, cut into the rotor of the grooves in which it is necessary to insert and glue with cold welding neodymium magnets. The working winding will need to be connected to the controller, which stabilizes and rectifies the current induced in it and provides a given voltage.
Such a generator will be able to feed the lamp or charge the battery. The rotor can be driven by drill, screwdriver, or a pedal mechanism. Other options are also possible.
Types of motors
In older washing machines, asynchronous electric motors were used. They consist of a stator with a winding and a cylindrical rotor, which is driven by a rotating magnetic field. They are distinguished by low noise, simplicity of construction, and enough high power. But also there are also cons - these are large dimensions and weight, complexity of smooth speed control, and low efficiency and torque. They also cannot work as a generator without alteration.
The most common are two-phase asynchronous engines.. They have a working and starting winding. The first is directly connected, and the second is through the phase shifting capacitor. Currently, asynchronous motors in washing machines are not used.
The collector engine is used in all modern washing machines. Works on direct and alternating current. It consists of a stator and the rotor, the magnetic fields of which interact, with the result that the latter rotates. It is equipped with a collector through which the stress through the brushes is served on the winding. Advantages - high torque and considerable rotation speed, which can easily and smoothly adjust. Collective motors are also capable of working in a generator mode with external excitation.
The inverter engine is connected directly to the drum. It is characterized by a rather complicated design. This motor can operate as an effective generator if the manufacturer of the electric motor installed the magnets in the rotor, thanks to which a considerable force will be induced in the stator.
Connection and verification
You must make sure that the selected motor works. To do this, determine the conclusions of the windings using a tester or multimeter. To check the operability of the collector motor, you need to connect one cable wire with a fork to one brush, and the other to the winding output. Free conductors are connected to each other. If the engine is working, the rotor will start rotating.
Asynchronous motor is connected differently. First you need to determine the working and exciting winding. The first will have greater resistance. It is supplied directly to it, and to the exciting - through the phase shifting capacitor.
Homemade engine from a washing machine (video camp, photo, schemes)
1. How to connect the engine from the old washing machine through a capacitor or without it
Not all "washing" engines will work with a condenser.
There are 2 main types of engines:
- with condenser start (constantly included by the condenser)
- With a launch relay.
As a rule, "capacitor" engines have three winding outputs, the power of 100 -120 W and turnover is 2700 - 2850 (centrifuges engines of washing machines).
And the engines with the "start relay" have 4 outputs, the power of 180 W and turns of 1370 - 1450 (the actuator drive of the washing machine)
Connecting a "condenser" motor through the start button can lead to power loss.
And the use of a constantly turned on the condenser in the engine designed for a start relay - can lead to winding brave!
2. Homemade emery from the engine washing machine
Today we will talk about alteration asynchronous electric motor From washing machine to generator. In general, I have not been interested in this question for a long time, but there was no special desire for removing the electric motor, because at that time I did not see the scope of the generator. Since the beginning of the year, it was working on new model ski lift. Your lift is good, but to ride music is much more fun, so I quickly ripe the idea to make such a generator to use it in winter to charge it to charge the battery.
I had three electric motors from the washing machine, and two of them are absolutely good. Here is one of these asynchronous electric motors, I decided to remake into the generator.
I'll say a little forward, I will say that the idea is not mine and not new. I will only describe the process of alteration of an asynchronous electric motor to the generator.
As a basis, an electric motor was taken by a 180 watt produced by the PRC of the early 90s of the last century.
Magnets ordered NPK "NPK" Magnets and Systems ", before I have already bought magnets when building a wind power plant. Neodymium magnets, magnet size 20x10x5. The cost of 32 pieces of magnets with delivery of 1240 rubles.
The remake of the rotor was to remove the core layer (deepening). In the resulting deepening, neodymium magnets will be installed. At the beginning, 2 mm core was filmed on the lathe - the protrusion above the side cheeks. Then, a recess of 5 mm for neodymium magnets was made. The result of the rework of the rotor can be seen in the photo.
Measuring the circumference of the received rotor, the required calculations were performed, after which the strip was made of the tin. With the use of a template, the rotor was divided into equal parts. Between risks, neodymium magnets will be passed.
On one pole used 8 magnets. In total, the rotor turned out 4 poles. With the help of a compass and marker, all magnets were marked for convenience. Magnets were glued to the rotor "superclaim". I will say, it's painstaking. Magnets are very strong, they had to hold them tight when gluing. There were moments when magnets were broken, pinched fingers, and the glue was shifted into the eyes. Therefore, glued magnets need to use protective glasses.
The cavity between magnets decided to fill with epoxy resin. For this, the magnet rotor has been wrapped in several layers of paper. Paper is fixed with scotch. Overters for additional sealing of plasticine are smeared. In the shell carved a hole. Around the hole made of plasticine made of neck. Epoxy resin flooded into the hole of the shell.
After frozen epoxy resin, the shell was removed. The rotor is clamped into the cartridge of the drilling machine for subsequent processing. Grinding was carried out by sandpaper medium grain paper.
4 wires left the electric motor. Found a working winding, and the wires from the starting winding cut off. I installed new bearings, since the old rotated tightly. Bolts tightening the case are also installed new ones.
The rectifier is assembled on diodine d242, the "Solar" controller is used as a charging controller, bought a few years ago on eBay.
The generator tests can be viewed on the video.
For charging the battery, 3-5 generator speed is enough. At maximum turnover of drills from the generator, it turned out 273 volts. Alas, the sticking is decent, so there is no sense to put such a generator on the windmill. Is that the windmill will be with a large screw or gearbox.
The generator will stand on the ski lift. Tests in field conditions already this winter.
Source www.konstantin.in.
4. Connecting and adjusting the revolutions of the collector engine from the washing machine
Production of the regulator:
Regulator Setup:
Regulator Test:
Controller on the Bulgarian:
Download:
5. Potion Circle of washing machine
6. lathe of washing machine machine
How to make an anterior woman with a lathe on a tree from the motor from a washing machine. and revolt controls with power maintenance.
7. Drovokol with an engine from a washing machine
The smallest single-phase, screw column with an engine from a washing machine with a capacity of 600 W. With a roller stabilizer
Worker turnover: 1000-8000 rpm.
8. Homemade concrete mixer
Simple homemade concrete mixer, consists of: Barrel 200 l, engine from washing machine, Disk from Zhiguli classic, gearbox made from Zaporozhts generator, Skifted Large from the washing machine Fairy, small self-pulp pulley, Clean drum made from the same disk.
Prepared and collected together: Maximan
Content:Washing machines with time wear out and fail. Most often, they are simply thrown into a landfill. However, in many cases, the details from the washing machine can be useful. There are many options for the second life of the electric motor. It all depends on the skills, opportunities and fantasies of the home master. In this article you will find out where you can apply the engine from the washing machine if it is in working condition. Consider what self-made from the engine from the washing machine can be made.
Electric motor for a grinding machine or emery
The purchase of the finished sharpening machine is not always possible, first of all due to the high price, and in this case, the electric motor from the washing machine or other equipment is literally irreplaceable.
A lot of effort requires the correct layout of the future unit, as well as a solution to such technical problemlike a grinding stone nozzle on the engine shaft. In many cases, it does not have a thread, and the diameters of the shaft and the holes in the stone do not coincide. The usual output from the position is the use of a special detail, which is necessary to be ordered separately in the Tokary workshop. This item may be called the flange, adapter, hub, etc.
The flanged flange should be embraced on the shaft and fixed with the help of a bolt. In addition, a washer and a nut with a carving, directed to the side opposite to the rotation of the engine shaft. Due to this, during operation there will be spontaneous twisting of the nut. Otherwise, the Nut will quickly promote and the stone flies.
If necessary, you can change the direction of rotation of the rotor. IN washing machines Installed, therefore, it is enough to switch the corresponding windings, and the direction of rotation will change. To start the engine, a start-up coil will need. If it is missing, then there is nothing terrible in this: when the stone is a push in the desired side, the device will earn independently.
For the manufacture of a grinding machine, it is not at all necessary to use engines of high power. It is enough 400 W, and even 100-200 W. It should be paid attention to the number of revolutions per minute, which should not exceed 3000. Otherwise, the motor with too high rotational frequency can lead to the destruction of the grinding stone. Most optimal option It is considered an electric motor with 1000 rpm.
Operation of the homemade sharpening machine involves strict observance of safety regulations. First of all, it is necessary to provide a protective cover to protect the abrasive dust and small fragments. For this, metal is suitable, 2.0-2.5 mm thick in the form of a strip, rolled into a semir. In addition, the manufacture of a girlfriend will need, to ensure the work being processed.
Transformation of the electric motor from the washing machine into the generator
Many home masters are engaged in the manufacture of self-made generators using electric motors from household appliances, including washing machines. This task is conjugate with certain difficulties, first of all technical Plan. In no compulsory, the services of a qualified Tokary will be required in the first stage of work.
First of all, it is necessary to disassemble an asynchronous engine taken from a faulty washing machine. Then the core falls into the hands of the turner, which removes the layer of the element, 2 mm deep on the machine. Then in the core, the slit of grooves to a depth of 5 mm is performed, in which neodymium magnets will be inserted. The grooves are recommended to do after the acquisition of magnets when their dimensions are known.
After all the work, neodymium magnets must be fixed on the core. For this purpose, a pattern made of tin or other thin metal is made. Its dimensions should coincide with the size of the core and the width of the grooves, and it must accurately fit into the installation site of the magnets. Magnets are located on the core at the same distance between themselves and are fixed with glue. In addition to the distance, the angle of inclination of each element is of great importance. Deviations from regulatory sizes may cause stipulation, as a result of which the generator power is noticeably declining.
Cold welding is used to fill the gaps between magnets. At the end, the surface of the rotor is polished with emery paper, after which the device is fully assembled.
The assembled generator must be tested. To this end, you will need a small battery, rectifier, multimeter and charge controller. Connection occurs according to a specific scheme. The charge controller is connected to the two generator windings through the rectifier. Then the controller and the multimeter must be connected to the battery.
For a normal check, it is necessary to rotate the rotor of the electric motor. It is impossible to perform this operation manually, so you should use a drill or screwdriver. The tool is connected to the engine rotor, after which the rotation starts at a speed of about 800-1000 rpm. With a high-quality generator assembly, the output voltage is 220-300 V. More low voltage Indicates a low-quality rotor assembly.
After assembly and check, the generator can be used. This will require the cost of energy required for rotation of the rotor. You can connect to a small engine internal combustion, for example, from chainsaws or a motorcycle. However, this method requires the acquisition of an energy source. Therefore, other options are recommended, relatively inexpensive and environmentally friendly, associated with the use of wind or water energy.
All homemade masters must remember that the electric motor from the washing machine can be converted into a generator, no more than 5 kW. Typically, such devices are produced on average 2 kW sufficient for 1-2 rooms or baths. So completely replace the electrical network homemade generator will not work.
Engine lathe from washing machine
The engine from the washing machine is ideal for the manufacture of a small lathe on the tree. The basis of the design serves as a frame that can be made from a corner, profile pipes and other primary materials. The dimensions of the frame are within 100 x 20 cm, with possible deviations in one direction or another.
The electric motor is quite suitable from the old washing machine, perhaps even from Soviet times. For example, Vyatka-machine equipped asynchronous engine With two speeds at 400 and 3000 revolutions per minute. Connection can be performed in all known schemes, including using the capacitor.
The engine mounting system to the frame is performed individually. The most important thing is that the axis of the engine is set up parallel to the reference design. This can be done using the washers that, if necessary, put on the points of the support. Front grandmother is fixed on the pulley of the electric motor. The rear grandmother and guides are also made from remedies. The axis of the backstone should be parallel to the frame and the front grandmother, that is, it is necessary to perform its center.
An important detail is a girlfriend that performs the support function for the cutting tool. It is necessary to ensure its movement along and across the beds, as well as reliable fixation during operation.
Electric motor for woodcover
The basis of the structure, as in the lathe is the window. It is made of metal profile or square. The obtained platform will consist of two zones - power and working. The power side is designed to install the electric motor. It must be securely fixed, since the main load falls on it.
In the same zone there is a motor control unit. To accommodate electrical components, a dielectric plate is provided, and they themselves should be placed in a plastic case. The work area is made in the form of a table. A steel sheet is used as a material, 2-3 mm thick. On the border, the pedestal is mounted conditionally separating both zones, on which the colon-cone shaft is fixed. This item cannot be secured directly on the engine shaft.
For the cone shaft, its own support on bearings is equipped. In order to compensate for the jerks and creating a torque, the flywheel is recommended on the shaft.
After assembling the entire design, you can start connecting the electric motor. Most often used asynchronous motors. In the old aggregates of this type, a separate winding is provided for startup. To determine it on the engine, you need to alternately measure the resistance on each winding alternately. The desired winding will have a higher resistance. It directly participates in the creation of the primary torque in the desired side. If necessary, change the direction of rotation of the shaft, the point of connection of the startup is vary in places.
Modern electric motors are launched significantly easier. You can use the usual household apparatus to turn on and off.
Washing Machine Concrete Machine
Concrete mixer is necessary in the farm, especially in private and country houses. However, the concrete mixers are quite expensive, so one of the solutions to the problem will be the manufacture of concrete mixers from the remedies. The washing machine is best suited, and not only the electric motor, but also the case itself.
The base should be reliable so that the container in the process of rotation does not fall. From this completely depends the duration of the operation of the unit. An unstable base can lead to a drop in capacity and failure of other elements. The most suitable is considered metal design. If desired, it can be equipped with wheels. All parts and parts are connected to each other with bolts or welding. To install the electric motor, you need to provide special shelves with fastening holes. On the same shelf and the gearbox is attached, the pulley of which should be in the same plane with the engine pulley. Otherwise, the motor will experience overload.
The on and off of the self-made concrete mixer is performed using a batch switch. In most cases, the condenser is present in the inclusion scheme. Thus, reflecting on what self-made from the engine from the washing machine can be done, any home master in practice will make a device most of all necessary in the household.
To date, it is very difficult to imagine a modern house without a washing machine. This equipment becomes an indispensable assistant of any mistress. In addition to clean clothing, this device is gratefully saved and saves the beauty of the hands. But, unfortunately, there is nothing eternal, and over time the washing machine fails and requires replacement. Folk craftsmen are in no hurry to throw out the old car, because, if you want and some knowledge, this device can be found quite practical application. The second life of the washing machine can begin in a completely new image. This device has a lot of valuable, useful nodes and units, thanks to which you can build up things in the farm.
The most used element of the washing machine is its door. Many craftsmen use it to place a small window, which is installed in small premises In the country area.
To get good and useful homemade, you can disassemble and use:
- Housing;
- Manual control (elements);
- Engine;
- Hermetic door;
- Pulleys;
- Drum;
- Pump;
- Relays and switches.
The originality is that the door very much resembles a ship of the porthole. Also, the door from the machine can be decorated with a dog booth. In addition to the original design, the door will have a practical purpose. If necessary, the dog can be isolated from guests. You can build a pretty coffee table from the beam. To do this, you need to take a few rods, they need to be consolidated to the drum. The glass table is installed on top with special fixtures.
You can install the LED backlight in the drum.
Such an original piece of furniture will be an excellent decoration in the style of high-tech, which can decorate a balcony, a veranda or attic. If you connect a fantasy from the old machine, you can make interesting and original decor elements that will be the highlight of the country's interior.
What can be made of washing machine-machine with your own hands
You can build up such a useful device with your hand from the machine, as a juicer. This device will become indispensable for the appearance of fresh fruits and vegetables during the season. Production of juicer is possible in 2 ways. The first option is a centrifuge with a washing compartment. This option allows you to create several processes in one device with minor modifications. Namely the process of grinding and pressed.
For the manufacture of:
- A washing machine is suitable where the activator is located at the bottom.
- For cutting, it is replaced 3 homemade kniveswhich can be made of strip steel.
- The drain hole of the tank must be drowning.
- A grid of stainless material is installed in the centrifuge so that the side surface is closed.
Before use, the design must be rinsed with food soda. The second option is made of the car barrel. To do this, you need to install a homemade centrifuge.
It is very important when installing to achieve an alignment, then the device will work better.
For this, the engine is suspended by 6 springs, 3 of which is balanced, and the rest are pressed up. For quenching strong vibrationThe structure of the design can be installed on the car tire.
Making an extractive machine with your own hands from a washing machine
For people who keep a lot of poultry, you may need a machine that is easy and quickly removes the pen. The perquance machine is also made of the typewriter.
For the manufacture of:
- The bottom of the tank is installed with a steel drive with a smaller diameter than a tank and a thickness of 3 mm.
- It drills holes in which rubber fingers put. On average, it is necessary to set 13-140 pieces.
- All other technical nodes can be not changed.
- In the side walls up 15 cm from the bottom of the tank, bleed fingers are installed in the same way.
- The lower disk must be installed on the drive shaft.
The hole is not necessary to be necessary, as it is useful for water removal. Before using this device, the poultry must be well scolded with boiling water and put in the tank.
After turning on the engine, the installed rubber fingers quickly remove feathers.
The process occurs quite efficiently, carcasses after processing are purified clean. The most expensive detail of this design are the rubber fingers that need to be selected by the type of pen.
How and what can be made from the motor from the machine
An old washing machine with a serviceable electric motor can be used to manufacture the generator. With the help of a motor, you can build a device that will help to organize lighting in storerooms or subsidies.
For this:
- It is necessary to disassemble the engine to extract the core from which it is necessary to remove the layer on the lathe on the lathe.
- After in the core, you need to cut the grooves in a depth of 5 mm.
- Neodymium magnets are inserted into the grooves at the same distance from each other.
To fill the gaps of magnets, cold welding applies. In the completion of the manufacturing process, the surface of the rotor must be seized. Next, you can proceed to the complete assembly of the device.
Mangala assembly from drum washing machine
The homemade brack of the washing machine can be used in the courtyard of a private house, in the country or an outdoor picnic. Production is possible due to the fact that the drum housing is made of durable stainless material, which has high properties withstand high temperatures. Making a brand from the drum is quite easy and simple, enough armed with the welding machine, and allocate some time.
To start:
- It is necessary to make a supporting part of the future mangala, it is best that this part can be removed, this will allow you to move the brazier at any convenient place.
- For the manufacture of support, only non-flammable and durable material can be used.
- The height of the leg feet is done at its discretion, if only it was convenient.
Many crafts for support use old metal coasters for colors. For the manufacture of this device, drums from front machines are suitable. If a vertical loading machine will have to cut one of the lateral sides using a grinder.
In addition to the mangala, the homemade round smokehouse will become comfortable and useful.
Mobile cryptille is made of drum, which is removed from the machine with vertical loading. All the lateral holes of the drum must be closed using a steel sheet. This is necessary so that the smoke does not dissipate in different directions. From above, you need to build a smoke pipe. It is possible to make it after cutting the hole of the desired diameter. Inside the drum, it is necessary to fix the lattice. The grille can be welded yourself or take from the stove. Using such a smoke can always. Such adaptations for cooking delicious meat and fish will be just a find for people who love to save without sacrificing their comfort.
Method for making a lathe from the engine from a washing machine
Motor can be used for manufacture small tool for wood work. The lathe is made from angle, which serves as a frame, profile pipes and other primary materials. The electric motor can be taken from any old typewriter. Even the engine from the washing machine of the baby is suitable. Adjust the engine to the frame can be any in a convenient way. The most important thing is that the axis is set up parallel to the reference design. Front grandma is attached to the motor pulley. The rear grandmother is made of primary materials and installed parallel to the frame. The main part of the machine is a girlfriend. This item executes the support function for the cutting part. It is necessary to ensure its movement along and across the bed. Also worth not to forget about reliable fixation During the operation of the machine.
By summing up, it can be bolden to note that with certain knowledge and work of fantasy, old things can become very necessary and useful in the economy. The alteration of old things allows you to save money, and create original and interesting devices such as oven, grill, electric generator, turning and grinding machine. Crafts can revive and decorate the interior not only the yard, but also at home. The washing machine has many details and elements that can be applied to make many interesting and useful aggregates. The use of an electric motor from the machine allows you to build kitchen devices such as the juicer and a sterilizer for conservation. In order to construct all useful devices, it is necessary to carefully develop a drawing, prepare the necessary details and tools. When everything you need is at hand, you can start assembling.
Homemade engine from washing machine (video)
Do not throw old electrical appliances, because in skillful hands old things can turn into the most useful and indispensable devices.
Send the material to you on E-mail
Scrap collectors will be simply happy to pick up your old washing machine. But do not rush to please them. Money for scrap you help out a bit, but if you come to this question with the mind, you can get a multitude of useful things for household. Self-models from the engine from the washing machine will help to quickly clean the bird from the pen, cut into pet food, cut the lawn, smoke fish and meat. And this is not a complete list of what can be made from the washer. Today in the review of the editors site detailed instructions, how to give the "iron heart" from the washing machine a new life.
Details from washing machine - Material for many useful homemade
If you are going to make homemade from the used engine, you need to figure out what it represents and what is capable of. You can meet three types of motors: asynchronous, uncoolette and collector. Consider them closer:
- Asynchronous - Maybe two-phase or three-phase. Two-phase engines are found in old models of still Soviet production. More modern machines are equipped with three-phase. The design of this engine is extremely simple, it can develop speed up to 2800 revolutions per minute. Shot from the machine operating engine you just need to lubricate - and it is ready for new feats.
- Collector - This type of motor you will find in the design of most household appliances. Such devices can operate from direct and alternating current, have compact dimensions and a controlled frequency of revolutions. The only drawback of this engine is the erased brushes, but these items can be replaced if necessary.
- Budcontator direct drive - The most modern engine from the Korean manufacturer. You will find it in modern washing machines from LG and SAMSUNG.
Now that you can determine the type of motor, it remains to decide where you can apply the engine from a washing machine.
Correctly disassemble and decide what can be made of the details of the old washing machine
Disassembly of the washing machine - a little business. After working with water on the details there may be salted growth, it needs to be accurately removed so as not to damage the spare parts when removing. What can be made from the old washing machine? Motor is useful for homemade - it will become the basis for many devices. A drum will go into business. It is usually made of stainless steel. From the drum you need to disconnect all the nozzles. Useful can be a hatch for download. In addition to these parts, do not rush to throw out the springs, counterweight and parts of the case.
How to make chopped or grinding device from the engine for washing machine
Sharpened - one of the most sought-after tools for the house. With it, you can make garden tools, homemade knives and scissors. If you still do not have this - buy it at any tool store or make a grip of a washing machine. The most difficult moment is how to consolidate the emery circle on the engine. The easiest way to buy a finished flange. It looks like this.
You can add a flange from metal pipe Suitable diameter, most often suitable tube with a cross section of 32 mm. From her you need to cut off a piece of 15 centimeters long, it is quite enough to fix the emery. The flange is fixed on the motor shaft with welding or through bolt. In the video, it is described in detail how it works sharpened from the washing machine, made with your own hands:
Making a turning machine on a tree from washing
What else can you do with the engine from the washer? One of the popular ideas is a lathe on wood. Consider a phased process.
| Illustration | Description of action |
|---|---|
 | For durable engine fixation on the workbench, make fasteners from a metal corner. To do this, drill holes for fixing to the legs of the motor and the table. |
 | For the fastening of the wooden part, the flange will be required, fixed on the motor shaft, and here are stiletta made from conventional bolts with cut heads. These studs turn into the base. It will take 3 studs. |
 | Motor fixation is carried out on the table with self-recesses, to the metal part - bolts. |
 | The opposite end of the wooden part is attached to such a device. It consists of a screw from the loop, two perpendicular to the corners of the wooden stands. |
 | This wooden part must be movable so that you can use different blanks. For mobility, it is fastened with a bolt with a bolt. |
 | To control the motor, the power supply will be required. You can use some of the computer blocks. You will need to install switches to adjust the rotation speed. |
 | How to connect the motor to the power unit in the animation. |
 | To guide tools, make a girlfriend. It consists of two wooden parts and a metal corner. All parts are movable at the expense of one bolt. |
 | The lower part of the girlfriend is toughly fixed on the workbench using self-tapping screws and corners. |
 | The workpiece is fixed on the machine on both sides: on the left - on the heels, on the right - to the bolt with the handle. For fixing in the workpiece you need to drill the corresponding holes. |
 | For work, needed tools - cutters. |
 | The final grinding of the workpiece is performed using a strip of sandpaper. |
How to make your own hands from the washing machine a simple domestic machine for homework
Bird slaughter time is a troublesome stage. Usually do it in the fall, when ducks and broilers have achieved the necessary weight, and keep them in the winter is already unprofitable. To pinch a few dozen, and then hundreds of carcasses need very quickly. You can get rid of the cautious work with the help of a perosnower, and it is easy to make everything from the same items of washer.
For the device, you can not disassemble the washer. It is especially convenient to use vertical loading machines. You just need to fix biles in the drum so that they look inside. Before the tip of the chicken, the carcass must be scolded with boiling water, and then just throw in a rotating drum. This is what happens:
Important!So that the water does not hit the engine of the throttle machine, it is necessary to protect it with a plastic casing.
And the last moment - the peroslement device must be firmly fixed, since the vibration when loading the carcass will be very strong.
Lawn mower from used motor
We continue to seek the answer to the question where you can use the motor from the washing machine. Another original idea is the manufacture. For a small area, there is a sufficiently electrical model tied to a power source with a cord. The device of such an aggregate is very simple. It will be necessary to make a platform on four wheels with a small diameter.
The engine is fixed on top of the platform, the shaft is loaded into the hole at the bottom, and the knife is attached on it. It remains only to attach to the cart of the handle and the lever to turn on and off the power. If your asynchronous motor has been lying on, you will be surprised how silent the unit will turn out, even in comparison with the factory models.
Tip! To make the grass, the grass is not wound, you need to slightly bend their cutting edges down.
Video: how to make a lawn mower
Kindle for animals
For a rural inhabitant, the corrosion is very important in the household apparatus. And this unit is easy to do from. You can use: drum and motor.
For the bubbles, it will be necessary to make a housing in which the drum will be mounted with sharpened holes for cutting with holes and a lid for pressing. The connection of the rotating drum and the engine is carried out through the drive. The finished model looks like this:
How to assemble a generator from the old washing machine
We continue to consider homemade from the engine from the washing machine, and the queue reached the generator. You will not be able to assemble a powerful device, but to the case emergency shutdown You can easily prepare. To convert the engine to the generator, it will have to disassemble it and partially cut the core. In the remaining part of the core, you need to make grooves for neodymium magnets.
The gaps between the magnets are filled with cold welding. To work the device, you need to turn on the battery from the motorcycle, rectifier and charge controller. Details of work in the video material:
Homemade concrete mixer
If you started a small repair, requiring, for example, plastering walls, you will use a concrete mixer. And the details of the washing machine will come up again.
As a container for concrete, you can use the same drum with pre-sealed holes for draining water. It is best to use the parts from the machine with front loading, there almost nothing will have to redo. To strengthen the housing, use a metal corner, and for convenient movement of the concrete mixer, equip it with wheels. The main complexity in the design is the manufacture of "swings" for the correct inclination and the subsequent plum of concrete. How to do this in the video:
Homemade engine from washing machine: Circular saw
You will be surprised, but also the circular can also be built on the basis of a motor from the washer. Important moment In this matter - optional equipment Motor device regulating speed. Without this, the additional circular module will work unevenly and simply will not cope with the task. Device assembly scheme:
The principle of operation of the device is simple: the engine leads to a shaft on which a small pulley is dressed. From small pulley goes drive belt On a large pulley with a disk saw.
Important! When working with a homemade circular, take care of the hands. All design details must be firmly fixed.
The resulting assembly will not be very powerful, so that it can only be used for the dissolution of the board with a thickness of up to 5 cm. How such a homemade circular works:
What else can be made from the drum of the washing machine: the original ideas of the decor
The drum with its proper perforation is the material for the manufacture of decorative items. Here are some interesting ideas.
Pockets and tables. In the drums with the door from vertical loading machines, you can hide the necessary little things.
Making a brazier from a drum from a washing machine, frequency
- Temporary product. Sooner or later it burns and requires replacement. You can buy a new one every time or use a healthy material, for example, a drum from washing. Make this craft from the drum from the washing machine - a couple of minutes. The whole charm is that oxygen is easily entered into the perforated container, which is why active burning occurs.
The metal drum will be able to withstand a couple of seasons. Make a comfortable stand for it so that you can not be tilted, and everything is ready. Standard length skewers are conveniently located in a small roaster. If necessary, you can slightly grab the welding a pair of guides.
How to make a good smoke boaram with a washing machine
Cherry on the cake in our question -. Fragrant smoked meat, fat and fish - What could be better to the table? If you have a tank from the vertical loading machine in the barn or the garage - consider it in a hat.
In the bottom of the tank, it is necessary to cut a hole for the furnace, inside the fastening for the suspension of products. It remains only to install the tank to the hearth, hang the fish or fat, cover the pot on top of the lid and swing sawdust.
It is important that the fuel under the smoke is tolere, and not burning. Such a device is better located away from home.
Important! For such a smokehouse will have to look. It can not be left for a long time, the fire can flared up, and instead of smoked you get a burnt product.
