The scheme shown in this section in some details differs from the export option. This is another topic. Separately touch it another time, a little later. You can download electrical strokes on the VAZ -08-09-099-13-14-15 (collection in the RAR 9 MB archive), good quality schemes may be useful, because our Lego VAZ is unpredictable and can combine the elements of the schemes in chaotic order on different models.
- headlight combined with front light
- electro-moto gearboxes of janitors for headlights
- temperature sensor OKL.ZhIDS
- contact Motor Compart Lighting Lamp
- electric signal
- button automatic inclusion Signal rear stroke
- radiator cooling electric fan
- temperature fan power sensor
- washer Washer Valve Headlight
- electric generator
- rear window washer valve
- washer valve windshield
- pump washers of Stalkov
- backlight of the subcontrol space
- candles
- connector socket for a portable lamp and a compressor with a nutrition of 12 V.
- pressure sensor in the engine lubrication system and the output for the control lamp
- Ignition timing cambread
- solenoid valve (installed on the carburetor)
- valve microswitch idle movelocated on the carburetor
- electronic switch
- babina (high-voltage coil) ignition
- diagnostic Connection Connector
- upper dead point detection sensor
- battery
- level control sensor brake fluid In Bachka
- electro-starter
- electronic control unit EL. valve carburetor
- additional starter switching relay
- reducer windshield cleaner with electric drive
- backlight control panel heater
- electrical fan stove heating salon
- additional active resistor
- switch mode operation of the heater engine
- neck cigarette lighter
- the backlight of the nonsense drawer on the panel ("glove")
- mounting block
- dashboard
- contact Stop Button Signal on Brake Pedals
- fuse fuses on the mounting block - 16 pcs
- manual Brake Lever Control Lamp Switch Button
- control Lamp Switch Button throttle valve Carburetor
- variable resistor adjusting the brightness of the instrument panel with the "0" mode
- outdoor lighting toggle switch
- tumbler inclusion accidental
- constimani Switch Key Rear
- rear Wind Heating Switch Key
- location of side turn signals
- buttons - contacts of the lighting light of the cabin (located in the racks of the left and right front doors)
- buttons - contacts of the lighting light of the interior lighting (located in the racks left and right rear doors, for model 2109)
- Flaf Combined with Salon Backlight Enable
- on the scheme, the sprinkler castle decay (the anti-theft system is not shown)
- on the circuit of the switch located on the steering column of the switch of the operating modes of the operators of stalk and "janitors"
- the signal button (in cars of different year of release, the button configuration can change, but the essence remains the same)
- the initial position of the turn switches, light headlights and overall lights is shown on the decay.
- combined rear lights
- flow sensor and fuel level in a reserve control tank
- electronic heating rear window
- lamps highlighting Gos. Room
- electric Cleaner Gearbox for Rear Wind
A - connector (block) wires connected to the sensor controlling the degree of wear of the brake pads
B - connector (shoe) of wires connected to individual lighting plaffones in the cabin
I - numbering plugs in connecting connectors to the mounting unit
II - Disintection of the electric drive
III - Cutting with conditional numbers of plugs in the ignition lock
K1 - Relay-regulator of time intervals for rear window washer
K2 - turning relays and accidents
K3 - Windshield Wiper Drive Drive
K4 - Location of jumpers on the site of missing relays controlling the health of lamps
K5 - power relay lamp far Light
K6 - Relays Driving a headlight cleaner mechanism
K7 - a slot for the relay of windows (relay plant not put)
K8 - Sound Sound Relay Signal
K9 - Cooling System Fan Power Relay
K10 - power relay element of the rear window heating
K11 - Power Relay Middle Lamps
Colored electric car vehicle VAZ-2108. With this electrical equipment scheme, each motorist can reveal the fault in its electrical wiring. If there is no measuring instrument, the car owner will be able to install, why the ignition does not work, the starter does not turn on, the heater system broke, or does not displays the required voltage generator. For the rest of the models, see the documentation.
Electroshem VAZ-2108
1. Block of the headlight (headlight, combined with front lamp); 2. Motors of headlight cleaners; 3. Temperature indicator sensor; 4 switches of the windscreen lamp; 5. Sound sound; 6. Rear Light Switch; 7. Fan electric motor; 8. Fan electric motor sensor; 9. HAPP OMOVA valve; 10. Generator; 11. Rear window washing valve; 12. Valve of the washing of windshield VAZ 2108; 13. Electric motor washing glass; 14. Podcast lamp; 15. Auto engine spark plugs; 16. Plug socket portable lamp; 17. Sensor of the oil pressure test lamp; 18. Sensor-ignition distributor; 19. Electromagnetic carburetor valve; 20. End switch in the carburetor; 21.commutator; 22. Ignition coil VAZ 2108; 23. Diagnostic shoe; 24. Sensor V.M.T. 25. Battery rechargeable; 26. Brake fluid level sensor; 27. Starter VAZ; 28. The carburetor valve control unit; 29. Relay additional starter inclusions; 30. Motor unit of the windshield purifier 2108; 31. LIGHTING LAMPATURE HEATERATORY HEATERATOR; 32. The electric motor of the heater fan; 33. Resistor Additional; 34. Switch of the electric motor of the heater; 35. Cigarette lighter; 36. Lamp lighting lamps; 37. Mounting unit; 38. Combination of instruments 2108; 39. Stop signal switch; 41. Switch of the control lamp of the parking brake; 42. Switch of the control lamp of the carburetor air damper; 43. Digital lighting switch; 44. Switch outdoor lighting; 45. Alarm switch; 46. \u200b\u200bSwitch rear fog light; 47. Rear window heating switch; 48. Side rotation indicators; 49. Plafth switches in front door racks; 50. Plafthrum switches in rear door racks (for 2109); 51. Salon lighting plander; 52. Ignition switch; 53. Switch of wipers and soys; 54. Sound Sound Switch; 55. Switch of rotation indicators, parking light and light headlights VAZ 2108; 56.phones rear; 57. Fuel level indicator sensor; 58. Element of heating rear window VAZ 2108; 59. Lighting lights lighting; 60. Motor rear window cleaner.
A. The tip of the wire for connecting to the brake shoe wear sensor;
B. Plothechy connector for connecting to the ceiling of individual lighting of the cabin;
I. Conditional numbers of plugs in pads mounting block; II. The numbering of plugs in the motor shoe; III. Conditional numbers of plugs in the block and contact switch contacts; K1. Relay time rear window; K2. Relay-breaker of the rotation and alarm indicators; Kz. Relay of the windshield purifier VAZ 2108; K4. Contact jumpers at the location of the maintenance control relay; K5. Relay inclusion of far beam headlights; KB. Relay of inclusion of the headlight cleaner; K7. Switching on windows (not installed); K8. Sound signal switching relay; K9. Switching on the electric motor of the fan; K10. Switching on rear window heating relay; K11. Middle Light Relay Plans.
Electrical circuit Car VAZ-2108 - second option
1 - block headlight auto;
2 - headlight cleaner electric motor (installed on parts of cars produced);
3 - switches of the windscreen lamp;
4 - beep;
5 - Engine cooling fan fan motor;
6 - sensor for switching on the fan motor;
7 - generator;
8 - electromagnetic valve of the inclusion of headlights (installed on parts of cars produced);
9 - electromagnetic valve of the rear window washing valve (installed on parts of cars produced);
10 - electromagnetic valve for the power of the windshield washing;
11 - spark plugs;
12 - ignition distributor;
13 - ignition coil;
14 - reverse light switch;
15 is the coolant temperature pointer sensor;
16 - starter VAZ-2108;
17 - rechargeable battery;
18 - the brake fluid level sensor;
19 - Switch;
20 - the sensor of the upper dead point of the 1st cylinder;
21 - diagnostic shoe;
22 - the control unit of the electromagnetic valve of the carburetor;
23 - starter switching relay;
24 - limit switch carburetor;
25 - the electromagnetic valve of the carburetor;
26 - Sensor of the control lamp of an emergency oil pressure;
27 - the electric motor washer glass;
28 - heater fan electric motor;
29 - additional resistor of the electric motor of the heater;
30 - the heater fan switch;
31 - windshield purifier electric motor;
32 - cigarette lighter;
33 - Lamp illumination of the heater levers;
34 - Plug socket for portable lamp;
35 - Podcast lamp;
36 - lamp lighting of a broad box;
37 - Mounting unit;
38 - instrument lighting switch;
39 - Parking brake control lamp switch;
40 - Stop Signal Switch;
41 - a subwoofer;
42 - Switch outdoor lighting;
43 - alarm switch;
44 - rear fog light switch;
45 - fuse chain of fog light;
46 - rear window heating switch;
47 - side indicators of rotation;
48 - VAZ-2108 plafof;
49 - Connector for connecting individual lighting;
50 - Plafth switches on door racks;
51 - ignition relay;
52 - ignition switch;
53 - a combination of instruments;
54 - switch of the control lamp of the carburetor air damper;
55 - rear lights;
56 - Sensor of the level pointer and fuel reserve;
57 - element of heating rear window;
58 - rear window cleaner electric motor;
59 - Loading lights lighting lights.
Car Generator System Connection System
Scheme of the contactless car ignition system
Fuses VAZ 2108.
Location: Open the hood and under the windshield you will see the mounting unit.
Circuits protected by fuses
Fig. 3.14. Scheme contactless system Ignition VAZ 2108, VAZ 2109, VAZ 210991 - contactless sensor; 2 - ignition sensor; 3 - spark plugs; 4 - switch; 5 - ignition coil; 6 - Mounting block; 7 - ignition relay; 8 - Ignition Switch
Fig. 3.15. System control system of electromagnetic valve carburetor on vehicles VAZ 2108, VAZ 2109, VAZ 21099
A - to the "30" generator's conclusion; B - numbering plugs in the control unit; 1 - limit switch carburetor; 2 - electromagnetic valve of the carburetor; 3 - mounting block; 4 - ignition switch; 5 - ignition relay; 6 - control unit; 7 - ignition coil
Fig. 3.16. Scheme of the compounds of the generator VAZ 2108, VAZ 2109, VAZ 21099
1 - generator; 2 - negative valve; 3 - additional diode; 4 - positive valve; 5 - Charging control lamp rechargeable battery; 6 - a combination of instruments; 7-voltmeter; 8 - Mounting block; 9-additional resistors of 100 ohms, 2 W; 10 - ignition relay; 11 - ignition switch; 12 - rechargeable battery; 13 - condenser; 14 - rotor winding; 15 - voltage regulator
Fig. 3.17. Engine cooling fan fan motor circuit on VAZ 2108 vehicles, VAZ 2109, VAZ 21099 with type 17.3722 mounting unit
A - to the "30" generator's conclusion; K9 - switch on the fan electric motor; 1 - fan electric motor; 2 - power switching sensor; 3 - mounting block; 4 - Ignition Switch
Fig. 3.18. WAZ 2108 Starter Connection Scheme, VAZ 2109, VAZ 21099
A - retractive winding; B - Holding winding; 1 - starter switching relay; 2 - Mounting unit; 3 - ignition switch; 4 - generator; 5 - rechargeable battery; 6 - Starter
Fig. 3.19. Engine cooling fan fan power circuit on VAZ 2108 vehicles, VAZ 2109, VAZ 21099 with mounting unit type 2114-3722010-60
A - to the "30" generator's conclusion; 1 - fan electric motor; 2 - sensor 66.3710 turn on the electric motor; 3 - Mounting block
On the Internet there is a big confusion with electric hammers VAZ 2109. The reason for confusion is the following factors:
1) VAZ 2109 models with carburetor system Nutrition was produced with a low panel (until 1998) and with a high panel (1998-2013).
2) high panel models can be both with carburetor and injector power system.
3) VAZ 2109 export options were produced additional options, for example, windows,
which B. basic configuration not
4) ECM (electronic engine control system) or, as elsewhere called, the ECU of various modifications.
So, in order to understand which VAZ 2109 electrochmem you need, let's go through each of the following factors in detail:
1) Do you know with a high or low panel your VAZ 2109? If you do not know, look at the pictures:
Understand high or low panel You can combine instruments on the control panel, as well as appearance Car panel itself.
2) If the VAZ 2109 is an injector, then in 99% of cases there is a high panel on it and you need a high-panel electrical circuit.
3) If your VAZ 2109 is an export variant, then the wiring diagram will be exactly the same as the base option, with the exception of options. Options can be different and usually find the scheme for your option will be problematic.
That is, the main scheme: the instrument panel, ignition, recharging, etc. - the same, will not be indicated only additional options.
4) Remember, the ESD wiring diagram is completely separated from the total electrical circuit. That is, if you swing in the Internet of the electric hammer of VAZ 2109, then there will be no controller in it, no sensors. Wiring Scheme Esud - Separate Technical Document; Search and download it is also necessary separately.
In each archive, two electrical strokes, their differences are that on the same mounting unit of the VAZ 2109 is drawn by one whole unit, the wiring inside the mounting unit is drawn. Naturally, the scheme option with a wiring of the mounting unit is more complete and convenient for working with car wiring VAZ 2109.
Also found a good program for the owners of old VAZ 2108, VAZ 2109. This program makes the power supply of VAZ 2108, VAZ 2109 interactive. That is, the user has the ability to choose its item item to the right in the window and part of the wiring to work with this node will be tired:
When working with wiring VAZ 2109 Always remember that the color marking of the wires is your chief assistant. Color marking Wires VAZ 2108, VAZ 2109 in the diagram and the car must coincide. We got the cable of wires and can immediately navigate - yellow - dimensions, red - stop - sign, blue - reverse, orange-black - fog lanterns.
Today, no car does not work without the use of electric current. Schematic scheme VAZ 2108 provides a spark for candles, makes it possible to use the radio and GPS navigator. With the help of electrical wiring starting from the battery, the voltage is fed to all machine devices. First, the current enters the fuses, then distributed over the lighting lamps of the road and instruments. Also, the wiring is mounted on the lighting light bulb.
Electrical devices auto
VAZ 2108 carburetor car is equipped with a variety of electrical appliances. The electricity generator connects to operation when the engine starts. Its task is to transform mechanical power into electrical energy. The totality of the device with the voltage regulator is called the generator set. The output parameters of the device must with any engine operation modes provide a stable recharge of the battery during the movement of the machine.
The constructive device and the principle of operation in all generators are almost the same. On the different cars They may only differ in the quality of manufacturing and sizes. To ignite a combustible mixture in the cylinders, the ignition coil gives voltage to the candle. Since each cylinder has its turn of the working stroke, the rubber distributes the sparks on the candles, which alternately fed to the combustion chambers. VAZ 2108 control system The carburetor adjusts the valve response moment. This ensures the timely opening of the dampers.
The generator stator is attached to the car body. Its front cover is located on the side of the pulley, the back cover - on the other hand, where the contact rings are located. From the motor, the mechanical force is transmitted to the rotary shaft through the belt. The stator itself is recruited from metal plates. In special grooves, its winding is stacked consisting of thin copper wires coated with insulating varnish.
The rectifier consists of six diodes installed in the cooling radiator. The stabilizer maintains a constant voltage value, despite changing the rotor speed, which changes depending on the engine load. The brush knot has a collapsible structure, in which the brushes are pressed against the rings with springs.
Car wiring is mounted on the temperature sensor, fuel level pointers and battery charging. With the help of wiring, all sensors are derived on dashboard. So the driver can see all their testimony.
The entire wiring of the car is collected in the harness, each of which has its own factory number. IN technical description Information about which device is connected to each specific harness.
Basic faults in the work of electrical equipment
Compared to the injector of the VAZ 2108, the carburetor is equipped with a simpler wiring scheme. This is due to the fact that there is no electronic control The fuel injection, and the process of supplying gasoline into the combustion chamber is mechanically carried out.
The serviceability of electrical equipment is usually checked by a voltmeter. With it, such malfunctions are determined:
- when turning the key does not turn on the ignition;
- the starter does not work;
- the engine does not start;
- the stove does not heat;
- the generator does not produce the desired voltage;
- lighting lamps do not burn.
The electrical circuits of rotary light bulbs are combined with chains of alarm. Old VAZ 2108 The carburetor has a voltage supply scheme to these light bulbs, tied to one fuse.
| Possible breakdown | Your actions |
| When some direction indicator does not work. | First you need to check the light bulb on the integrity of the spiral. If the lamp has not burned, the cartridge contacts are checked. They may turn out to be oxidized, which will cause the disappearance of contact with the light bulb. |
| When both stop signals do not work, the fuse failed. | In this case, you need to remove it and call the tester. If it is not ringing, it should be changed. |
| When one stop signal does not work. | The reason most often lies in the bulb or bad contact. You need to check the light bulb and, if it is proper, clean the contacts with the help of sandpaper. |
| The failure of the electrical equipment of the rear light. | One of the reasons for this may be a blown fuse. Through it, the voltage is supplied first to the sensor, and only then on the light light bulbs. If the fuse turned out to be normal, then you need to do the following. Disconnect the green and orange wire from the sensor plug, connect them to each other. After that, turn on the ignition and look at the rear light lamps. Their glow will mean that it is necessary to change the sensor. |
Many auto owners after refilling the backlight of the rear end believe that the problem is not very significant. But when reversing at night in a narrow courtyard there is a high probability of encounter with some kind of fence or a tree that is very difficult to see in the dark. This can cause damage to the rear bumper.
So that the accident does not happen, the malfunction is better to immediately eliminate.
