Parktronic is a parking assistance system that obsesses you about approaching the object and displays the distance to the object to the object or indicator.
Currently, the parking sensors reverses many car enthusiasts when parking in the city or in dark time day. After reading this article, you will understand that the installation of parking sensors on the VAZ with their own hands is a simple operation.
The principle of operation of a parking assistance system.
Parktronic sensors installed on the bumper of the VAZ car transmit an ultrasonic signal, which reflected from the object is accepted by the sensors and is transmitted to the control unit, which calculates the distance to the object and transmits it to the display or bipper.
We will need:
- Parktronic himself. In stock with four sensors and LED indicator. (bought on Aliexpress)
- Special crown with a diameter of 22mm.
- Drill / screwdriver.
- Means for marking (pencil, roulette).
- Now take in the hands of a pencil and roulette and lagging a bumper. Between the sensors, the distance should be 30 - 40 cm. If you install a parking sensor on the VAZ 2109 or similar to the dimensions, the car can be placed as: from the edge of the bumper 20 cm and between the sensors of 34 cm. From the top you need to take about 5 cm, since on the bumper VAZ 2109 in the area of \u200b\u200b6 cm there is an amplifier of the rear bumper and you can get into it (it is from the same material, like the bumper itself and drill normally). It should turn out something like this. We tried to install sensors not at an equal distance, no problems are noticed.
2. Drills the holes with a diameter of 22 mm, the crown, which comes with a parking sensor.
3. Install the sensors in accordance with the marking (A, B, C, D).
4. Extend the wires in the trunk. It is convenient to do through the hole for rear light.
5. Install the Parktronon control unit in any place convenient for you in the trunk and connect all the wires to it.
PackageTronics Power take the reverse lamp wires. When turning on the rear transmission, the parking sensors will automatically turn on. To exclude "scrubs" and tape, I recommend using clermets.
6. We pave the wire to the display.
7. Install the display and connect it to the parking assistance system control unit. We check the performance of parking sensors set by your own hands on the VAZ turning on the rear gear.
Parktronic is a very useful thing for any driver, especially for a beginner. This device allows you to conveniently and quickly park in the most difficult situation. Thanks to such a system, the driver knows exactly how much his car left behind the obstacle. If the goal is close, the system begins to make sound signals of a certain frequency, light bulbs may also light up. And if a more professional system is selected, then in the salon on the liquid crystal display, you can even see the distance to the obstacle in numbers.
This article we will talk about how you can install a parking sensor on the VAZ 2114.
Materials and tools for manufacture:
- set of parking sensors;
- bumper;
- Wires;
- soldering iron with a solder;
- self-tapping screw;
- roulette;
- drill with a cutter by 22 mm;
- Screwdriver and other tools.
Parktronic installation process:
Step one. Preparation of bumper
First of all, the author removes the bumper and gives it to painting. Already after the bumper is polished, closed and painted, the necessary sensors are installed in it.
Among other things, you need to not forget to install all fasteners on the colored bumper, if they were filmed before painting. To do this, you need to spin four screws and four bolts on 10.
Step second. Marking bumper
At the second stage, the bumper needs to be placed. You need to accurately determine the places where parking sensors will be installed. Two sensors are installed along the edges, and two more closer to the center. If the sensors are simply positioned in the center, the system simply does not see an obstacle if it is on the edge of the bumper.
Now you can proceed to drill the bumper and the installation of sensors. Most of the four holes, the fifth was drilled for other purposes, the author plans to establish a chamber there.
After installing the sensors, the bumper can be installed on the car.
Step Three. We carry out wiring
To wiring in the cabin, you will need to unscrew the rear lights. At the same time, two wires will be held on the right side and two with the left. As you can see in the photo, the lanterns are fastened with four bolts.
In order to fasten the Parktronic block, small screws were used. Block attached to an acoustic shelf. At the final stage, all wiring hides under the upholstery.
In order for the Parktronic monitor only after switching on rear velocityplus you need to file from the rear light. To do this, it is necessary to ring the flashlight block and find there plus, which is turned on solely when the rear speed is turned on. The wire on the VAZ 2114 has green color. As for the minus, it is taken from the mass, for this, the wire can be fixed with the lantern fastening nut.
Next, the wires need to be stretched from the Parktronic block to the monitor, which is located in the cabin. The author handed the wires under the carpet, the thresholds were unscrewed. Where to secure the monitor, you can see in the photo.
That's all, after the system is collected, you can proceed to testing. According to the author, the system is a little lack of reaction, so for those who like to quickly ride the back, the system will not allow you to determine the distance to the obstacle. If you park slowly, then everything works without any problems. When about 20-30 cm remains to the target, the system begins to "squeak and blush." However, you can navigate both the display and sound signals. If necessary, the same sensors can be installed in front of the car.
Parktronic is a device designed to facilitate the process of parking a novice motorist. Install parking sensors in numerous car dealers or your own hands. We consider exactly the last option when there is no desire or opportunity in the car service.
First you need to decide on the choice of device. Now in stores there is a huge amount different models and modifications. By and large, there are few differences among this set. The main differences are to appearance Monitor, and the characteristics of the sensors themselves are no different. On the bumpers of the car you can install a different number of sensors. Usually motorists are installed 4 on each bumper, and some motorists put only on the rear. Particularly relevant parking sensors on tonned machines, when under conditions of limited visibility, you have to take back to the darkness.
Installation process
Immediately before installing parking sensors, wash the car. Next, it is necessary to define the places most suitable for the installation of the sensors. For example, in the jeep fastening the spare wheel, which can be placed on rear door- Extreme overall point.
At the next step, it is required to dismantle the car bumper. In the process of dismantling, you should be careful not to confuse the fasteners for the front and rear bumper. After that, you need to make marking and drill holes for parking sensors (Fig. 1). But you can not remove the bumper - you can drill holes and so, only then you need a certain skill and patience to carry out wires in the car's salon.
Fig. 1: Place the places on the bumper for sensors
In the course of marking places for sensors, it is important to be extremely attentive: unnecessary drilled holes will not be eliminated. In order to further navigate in the parking lot, parking sensors are located at the same distance from each other.
The next step is to lay the wires (Fig. 2) and connect the device sensors to the electrical circuit of the car. Before connecting the sensors and the parking sensors, you need to de-energize the car's electrical circuit. Put the wires from the sensors to the boarding sensors need extremely gently. Rear bumper sensors can be connected to the power of the reverse fan. Thus, parking sensors will only work when you are enabled reverse gear. It's comfortable - once again There will be no squeak in the car, when, for example, someone will come back in a traffic jam.
Fig. 2: Laying wires from sensors
Next is set to the board (Fig. 3) and all sensors are connected. The location of the board of Parktronic should be extremely favorable for the driver: it should see the display of the scoreboard, without changing the position of the head.
Fig. 3: Parking Radar Scoreboard
That's all! The whole procedure takes 2-3 hours - it's not so long, but at the same time informative. And below we offer to see the whole process on the video.
The process of statutory on video
Almost all car owners, at least once heard information about the ditch accidents.
Such information is often reported by newspaper media, television channels, while giving a large number of recommendations, exactly how to behave when entering such a situation. Nevertheless, people often completely forget all the received advice, giving them the opportunity to the chairs to make themselves an involuntary participant in a similar accident, including his culprit. How to act to reduce to the minimum level of the likelihood of entering this situation?
Principles of choosing "Victim". First of all, it is worth declaring what type of car owners most often comes across such schemes and becomes their victim. The most optimal goals for fraudsters are those drivers who manage inexpensive budgetary machines Foreign production, or high-quality domestic machines. They choose car owners who drive alone, and therefore do not have unnecessary witnesses in the cabin. The second most suitable option, female drivers are becoming. They cannot have physical resistance, and they are easy to intimidate them. But there are several categories of cars that almost never touch scammers. These include, for example, cars that are installed "thorough" numbers. In addition, they do not apply in their criminal schemes and "processing" owners of expensive SUVs or business class sedans. Attempts by their "divorce" can cause problems with the criminals themselves. Another type of machines, which rarely use similar schemes, become machines with tinted glasses. Simply put, they do not touch them for the reason that there is no possibility to see the number of people who are inside. And the latter who will not touch the autobriver, are cars with several people in the cabin. The reason is that they do not need unnecessary witnesses, in addition, the need to intimidate several people much more complicates the task.
Execution of a ditch accident. During the execution of such actions, attackers use cars of sufficiently well-known manufacturers who have a spectacular appearance. A feature of them can be the complete absence of numbers, or what they are smeared by mud. The second option may be the use of unreal license plates. On the left side of such machines, there are often damage that went to her in previous operations, or specifically applied. The total number of participating cars is most often equal to two. The task of the first of them becomes the displacement of the victim's car beyond the limits of the strip, the second goes on the collision. They adhere to this principle almost constantly.
Driver behavior in such a situation. Should they try to resist such actions? Of course yes.
- To do this, it is necessary to purchase a DVR in a car salon. A similar witness is quite difficult to intimidate or bribe.
- To call in the traffic police should always be independently, not trusting anyone;
- In the process of waiting for the arrival of the outfit, it is necessary to remove the location of both machines on the camera, and those damage they received. Do not forget about the appearance of the criminals themselves.
- If you are threatened, you should simply close the car from the inside and immediately cause the traffic police.
Outcome. One of the rules that can help avoid getting into a similar situation becomes observance of traffic rules. Often, criminals seeing that everything is developing not by their planned scenario, leave the place of action, without waiting for the emergence of traffic police officers.
For many parking sensors have become an integral part of the car, as they allow you to make parking much easier. The reason for this is a huge number of cars and the lack of parking spaces, and if they are, it will not be easy to stand there. It is for this that the parking sensors are needed. Sensors scan the space from the back and front of the car, warning about the object approximation in advance. On many modern cars Foreign production, parking sensors are installed from the plant, but in the Russian car industry about such innovation and do not think. You have to do everything with your own hands. This article will describe in detail the process of installing parking sensors on the car.
So, let's begin. First you need to select a set of sensors that will more or less comply with the standard. Typically, sellers in auto parts stores do not try to slip you any garbage, since in many cases they themselves do not know what is better. Choose a set of parking sensors is better in their number, the minimum number of sensors 2. For more detailed scanning of the area and to scan dead zones, it is best to purchase a set of sensors in which the list includes 4 sensors.
The main thing when installing parking sensors to determine the correct location of the sensors on the bumper. If you do not do everything, then the sensors will be a bit, but deceive about the approaching objects. Thus, the system will notify you about the distance to the object or completely early, either too late, and may not detect objects at all.
When choosing parking sensors, consider their resistance to temperature, to the car's arrival in the car wash, etc. If you consider these parameters, then you will not suffer in winter time year in frost. There are several types of parking sensors, such as Multitronics PT-3TC sensors, have the ability to work with certain onboard computers TC 750, VC731, RC-700 and many other computers from Multitronics. If you have a desire to paint the park proxy in the color of the car, then you can paint them with ordinary paint, this will not affect the operation of the sensors. Prices for parking sensors are different, they begin with one thousand rubles, depending on their quality and brand. Something I talked, let's get to the installation of parking sensors. We start work. In order to set the sensors, we will need to drill four holes in the bumper equal to the diameter and altitude of the location on the bumper. For convenience, the bumper can be removed, but you can do without it, since everyone is comfortable in different ways. Using a centimeter, mark the appropriate distance between the sensors and drill the holes in the right place.
Now you can install parking sensors. In my case, I removed the bumper and only then began to drill. For drilling in a set of parking sensors there is a special crown, which has accurate sensor size. We set the sensors and adjust so that they are in the same plane. Now you need to stretch the wires. I decided to stretch the wiring through the trunk. With the help of drill, we do the hole in the body and go there wire there. Extend the wires in the trunk. Now in the right rear corner of the trunk, fasten the control panel of the sensors and feed this panel from the plus wire, the reverse light bulb, so it will only work when the included rear progress. Now everything is ready, check everything in business and rejoice.
