All, probably, front-wheel drive cars, the VAZ family, there is a disease that directly affects not only safety, but also presses on the brains of drivers - these are rear non-working lights. Invented even probably at Stalin, the rear lighting board of such brands of such brands as a VAZ 2110,11,12 and the VAZ 2108 -2115 is presented with a thin tape with conductive paths. Some drivers know how they are this tape and changed a year several times, and with it, in most cases, and blocked light bulbs. But this replacement helps only for some time ... And then again, Material words are going to move and so on ...
Here the drivers 2108-2114 and 2110 have an alternative to have such an Optics of Osvar domestic production, but the vases 2115 were offended in this regard. Chinese, which fills the markets, does not really want to buy, then we will look for a solution for yourself. There are several options for solving this problem, but today we will consider the option of full failure from this thin tension and inserts of iron cartridges for lamps (from VAZ 2101)
So let's start ...
We remove and disassemble the rear lights, take out the board from them, we use the screwdriver the cartridges (plastic) and get the ribbon itself.
on the ribbon is clearly seen where there was bad contact on the lamp
In the lamps of VAZ 2115, double light bulbs are used, in the foots and dimensions, it means that the store buy double cartridges for stops and dimensions, and for turns are single. In other cars, VAZ 2108-2114 chucks are single all. There is still a wire (copper single mild cross section 2.5 mm), connectors (I took from the computer), bolts M3.
Here is the scheme of the compounds standard, VAZ 08-15. Everything is clear here, his plus goes to his cartridge and the total mass.
there is no on this scheme for VAZ 2115.
For her here ...
We get patience to start work. We celebrate the places for the cartridges and drill them, the places are the same as previously. Metal cartridges need to be modified slightly in the cartridges of stop signals and dimensions, namely, we take the passage and conclusions for tips to move 180 degrees. Then we take cartridges from the turn signals and whining them there at all.
Holes. which dried with a refinement with a file.
Then we take bolts with nuts M3 and kpripim them cartridges to plastic. It turns out neatly, but the work is painstaking and requires patience
The store did not have cartridges for turn signals with a single contact, I had to discharge the jumper in a double carton.
How all the cartridges will be attached to the electrical part, that is, the gasket and the soldering of the wires.
The first thing we make connect all the cartridges that makes the total mass, then we are deposited plus on the turn signal and plus at the foot and dimensions. After this procedure, we all nickly, check if there is no closure (so that the soul is calm), well, and then we increase the block of the connector
Well, that's all, now all this economy needs to put on the car, well, I think you can cope with yourself)))
The appearance of modern LED elements led to creating a new turn in a car tuning. Motorists began to decorate the interior of the car, doors and, of course, optics. If the front optics are decorated with "angel eyes", then the rear lights owners of VAZ 2114 and other cars prefer to put LED elements. The rear headlights on the VAZ 2114 are easy to tuning, but almost all of them are associated with the installation of diodes.
Interesting: In addition to the decorative value, the LED backlight is also present and practical benefits: LEDs increase safety, so their glow is brighter than that of incandescent lamps; Riding becomes more comfortable in all weather conditions. At the same time, such tuning is permitted by law in the CIS countries.
Tuning Options Rear Lights
LED lining, diode rings on lights, separate LEDs and powerful light bulbs in the darning film - tinting are very popular. Attention deserves each option to decorate optics:
Making overlays
For the manufacture of linings, you will need the following tools and materials:
The instruction is suitable for homemade decorative decoration or purchased. Muffd up diode linings with a scotch or its alternative:
- Rear lights need to be covered with painting scotch. After that, you need to apply fiberglass on the tape.
- LED lining will be installed in it, then the fiberglass must be impregnated with epoxy glue. It follows 2-3 thin layers. All irregularities need to be removed, and then wait for a complete drying, which in conventional garage conditions lasts 12 hours.
- When the glue is dry, you can remove the workpiece, and then schedule the contours of the future ornament with a scotch or marker. After that, the developed profile is cut with scissors. When two forms are cut, you can move to putty. The dried surface must be pulled out fine-grained sandpaper. After the soil is applied, and then the main layer of paint.
- After 100 percent drying, a protective varnish is applied. Diode overlays are installed on the rear lights. Tuning completed.
Tip: LED lamps You can decorate not only the rear lights. Vaz owners often put LED tapes as turn signals and fog lamps on the front optics. Another interesting option is to decorate the wheeled disks and dashboard.
Installing LEDs in the rear lights
If the LED linings are installed on top of optics, then the diodes need to be inserted into the headlights - it will take the skill of working with electronics and a soldering iron. Before starting the installation, the LEDs should be prepared along with the board, it all depends on the possibilities and desires of the motorist - in the future the LEDs should be freely connected to the wiring of the car VAZ 2114. It is also necessary to make a stabilizing circuit. For this, stabilizers are sold, which are sold at the number "7812". It is necessary so that lights in the overall mode ensure a weaker glow, and 100% power was given in the stop position.
For those drivers who value the creative, you can advise to make LED arrows on the taillights, which will be used in the future to indicate the turn. It looks stylish and original. Motorist will need to collect several boards that will depict the arrow.
Such tuning with your own hands requires a large number of materials. This is a set of LEDs along with resistors, fastening for diodes, adhesive film, sealant (preferably it is silicone), epoxy glue. Surrounding may find the question "How many tuning requires LEDs?". Here you need to independently explore your taillights, while taking into account the turning relays. You need to buy LEDs with a reserve, as they can overdo it with time, and an exact copy may not be. The role of diffusers, according to motorists, the white LEDs are better suited, the turn signals decorate orange diode elements, "brakes" - red, and reverse - transparent.
Step-by-step instruction
Installation of LEDs on the rear lights is performed in such a sequence:
- Lantern must be removed from the car. Next, it must be cut into two parts - a qualitative device for burning can cope with this. As a result, it should be smooth and thin seam.
- Now there are access to reflectors and reflectors - they need to be removed.
- Rear headlights need to be fully disassembled. It is recommended to note the marker the position of future LEDs on the outer surfaces.
- Inside you need to stick the circles from the self-adhesive film with a diameter of 15 mm.
- The surface of the overall lights and stop glands should be covered with silver paint. When the paint is completely dry, self-adhesive film can be removed.
- Reflectors are installed on a small layer of epoxy glue. After that, you can miss all the joints with a sealant as prevention.
- LED boards are attached to wiring and placed in the headlight housing.
- A stabilization scheme is established that will regulate LED connections.
- Rotary blocks can now be assembled and combined with the rear headlamp. The epoxy glue must be planted modules. If optics work properly, you can glue the block - tuning is completed.
Making diode rings
To create rear headlights with their own hands, the presence of all the same epoxylin, strong glue. Based on diode rings or tape. The case will be made of small and large catapho, which can be found on the "ironing" market. The last element is the paint that is more like a motorist. Most VAZ 2114 owners choose paint under chrome.
- Diode rings should be installed in cylinders that are best made from tin cans. For this, banks are suitable for coffee or canned food.
- They need to be carefully cut, so that at the end there is something like a well. There should be two internal and external. If the can from coffee can serve as the basis for an external well, then the internal can be made from a conventional plastic cup by 0.5 liters, and then paint.
- Now the internal wells should be put by simple Soviet catails. They should provide highlighting according to the standard scheme: turn signals - orange, reverse - white, fog - red. After that, unnecessary elements may remain from a large catator that will look great inside the module. The rest of the place can be decorated with any LED ring.
- The following procedure is the installation of reflectors and LED rings. So that they securely keep, it is necessary to make the ribs of stiffness, as an option - epoxylin.
- You can put additional backlight on the plexiglass and secure the epcosiline.
As a result, it should turn out such tuning with your own hands. Detailed visual allowance for the installation of LEDs in VAZ optics:
One of the most popular Hatchbacks of domestic production in motorists is the VAZ-2114 model. But this car is very far from the ideal, and bring it to "to mind" is already already the owners themselves. And they do it by alterations and modernization, which concern not only the technical part, and the appearance.
One of the elements that is subjected to any changes is optics on the vases. Many regular lighting equipment does not quite suit, so they make their own adjustments, including in the rear lights of VAZ-2114. Note that some improvements not only change the appearance, they still increase the efficiency of the rear headlights of the VAZ-2114, which makes the signals supplied even more noticeable. Therefore, tuning rear lights - not such a useless thing, because it also improves safety.
Tuning species
Tuning rear Lights VAZ-2114 for the most part reduces the installation and use of LED elements in optical devices with a number of positive qualities:
- Brighter light;
- Low energy consumption;
- The ability to install LED elements at its discretion;
With all this, such re-equipment is not illegal, therefore, for the improvement of the rear headlights on the VAZ-2114, there will be no problems in the future.
The main types of tuning rear Lights VAZ-2114 are their hands:
- Full replacement of the rear standard optical equipment on alternative;
- Replacement of standard lamps on LED;
- Installation of more powerful lamps (usually done with reversing lamps);
- Installation of the rear PTF;
- Toning optical devices (film, varnish);
Installation of alternative lanterns
For many car owners, such an operation, as the self-made alteration of the rear Lights of the VAZ-2114, is for some reason difficult. Some believe that everything is "crooked", others simply do not want to do themselves. For such motorists who want to change the appearance of the machine, there is a great option - to establish alternative rear headlamps on the VAZ-2114 instead of regular. Such alteration is convenient because you do not need to change something in the block headlights: I purchased a tuning set of lanterns, installed it instead of relatives, connected everything.
The auto accessories market for the choice offers several types of alternative optics on the VAZ-2114, which make up the most liked option for installation. Such, for example, are kits for replacing headlights VAZ-2114 production of Osvar, Prosport, DLK, etc. In general, choose from what.
Our company offers elements of tuning of the rear optics of cars VAZ, as well as foreign cars. Make the back lanterns "Fishka" of your car will help our specialists who will not only install the products you have chosen, but also advise specific models for your car.
Tyuning types for rear lights
Tuning rear lights Different models of cars VAZ and foreign cars are carried out by qualified specialists from our company with extensive experience in the production of these work. In addition to standard elements tuning rear lights, We offer our clients LED tuning, which will allocate you from the stream and will attract the attention of others. When installing the LED tuning, the glow of a certain part of the headlight or lantern (rotation, reverse, envelope or stop) becomes brighter and contrast, which is important for your safety.
Tuned rear optics (LED rear lights), except for basic functions, plays the role of a decorative element that makes the car exterior more attractive. What exactly will the nature of the tuning of the rear optics - the case of your taste and creativity, as well as the experience of our specialists.
What we offer for tuning lanterns
We suggest radically change the look of the rear lights of your car. They can be painted from the inside, while denoting on optics to pass the light of any to choose a picture: circles, squares, diagonal, etc. You can purchase special overlays on optics, such as a body for modular optics with a place for a number, as well as without it.
Rear lightsthat we offer as an element tuningmay be an alternative option for rear lamps for VAZ cars. As a rule, these are LED rear lights. They will not simply improve the appearance of your car, but also make others get to turn around to you. This section presents a wide range of elements. tuning rear optics from various manufacturers. Quality We check at the entrance of the goods to the warehouse, so you are insured against the acquisition of non-working products. The price of tuning, as well as the work of our specialists, is absolutely acceptable. A warranty is provided to most of the goods. Customer reviews about PSG Tuning services will be confirmed by our successful work.
We hope you see among our customers!
Tuning process lamps:
Step one. Installing LEDs and Painting Lanterns
First on the outer part of the lantern, you need to glue the LED ribbon. To do this, it is initially necessary to place a flashlight and determine how the diodes will be located on it. Next, the LED tape is necessarily fixed using epoxy resin. Otherwise, the tape will fall behind, since the diodes are very hot when working.
After that, it is necessary to cut squares from paper and stick them on each LED, it is necessary to protect them so that the diode is not painted. Well, after that, the lantern is painted in a black matte color right over the LEDs. After the paint is driving, the paper can be removed and the diodes will be open.
Step second. Installation of linings on lights
To hide the LEDs, the linings are installed on top of the lantern, which the author pre-buys in the store. A couple of such lamps cost 400 rubles, black lights were chosen. Thanks to this, native lanterns are almost visible even during the day, due to the fact that it is painted black. Lining with the help of black silicone sealant are attached, it provides good tightness and fixation.
Step Three. Connecting diodes
To connect LED tapes, in your native lamp you need to make holes for the wires. Next, the wires are simply soldered to the contacts to which standard light bulbs are connected. Stop signal and enabread must be connected through diodes, for this, diodes are suitable from rectifying bridges, as they are quite powerful for these purposes. Conventional diodes can burn. When you click on the brake, not only stop signals are lit, but also rear dimensions.
Well, accordingly, you need to not forget to connect the right and left turn.
That's all, on this tuning can be considered finished. What came out, you can look at the video.
