Home Generator Brake fluid for Hyundai Solaris 1.4 automatic. Replacing brake fluid in Hyundai Solaris. Features of brake fluid replacement on Solaris

Generator

Brake fluid for Hyundai Solaris 1.4 automatic. Replacing brake fluid in Hyundai Solaris. Features of brake fluid replacement on Solaris

Liquid

The same operations that are done on the front wheels, you need to do on the rear;

We start with right rear wheel - on the valve that is worn and plunges into the container, a bit filled with brake fluid;

The assistant sits in the car and strongly until it stops 4 - 5 times pressing the brake pedal, and then keeps it pressed;

At this moment, the valve is unscrewed by three quarters, which, and a dirty liquid begins to flow into the container;

After the fluid has stopped acting, the valve closes, and the pedal is released;

The entire operation is repeated several times until a clean brake fluid go from the valve; then all of the actions described above must be done on the left front, then on the left back, and then on the right front wheel - It is necessary to clearly observe the sequence. Throughout the work, it is necessary to monitor the level of fluid in the tank, it should not fall below the minimum mark - so during pumping brake system Liquid need to constantly add.

Brake fluid, like others lubricantsrequires periodic replacement. This is due to loss of qualities, during operation is lost. So, the replacement process brake fluid Hyundai Solaris is quite simple.

Videos

The video will tell how to quickly and correctly change the brake fluid in the car, and also tells about the nuances and tricks of the process

Replacement process

Brake System on Hyundai Solaris. It has two contours, they are completely isolated from each other and are divided into parking and working. Such their uses on auto provides increased security of the car. The duty of each driver is charged to watch them technical condition And in time to carry out the regulatory and change the liquid. How to replace the brake fluid (TZH) on Hyundai Solaris will show in a visual photo of instructions.

We carry out the replacement of the brake fluid on Hyundai Solaris. We unscrew the lid on the brake fluid tank.

Tools and consumables required for replacement of the DJ:

new brake fluid;
rag;
key size "on 10";
transparent hose and capacitance.

To quickly and successfully replace the TW and pumping the brakes, it is necessary to attract an assistant, and replacement actions to carry out on the observation pit or the overpass.

So, the change of fluid also provides for pumping the brake system, so we will consider at once two questions in one topic. The sequence of actions aimed at replacing the brake fluid in Hyundai Solaris regardless of the year of release and body model:

For any "fireman", it is recommended to dismantle a minus terminal from the battery.
Using a screwdriver, remove the mesh from the tank.
With the help of pears, we pump out the old liquid from the tank.
Pump the syringe through the spent liquid from the tank.
After that, pour into the tank new liquidand proceed to pumping the brake system.
Install the mesh in place.
Since the contours of the brake system are diagonally, the pumping scheme is as follows: Rear left - front right - rear right - front left.
Fill a new fresh DJ in the tank to the Max.
Now, it is necessary to clean the fitting for pumping the brake system from dirt and other unwanted items. And then, dismantle the rubber protective cap of the fitting.
We produce a replacement of the TW according to the scheme, starting pumping from the rear right wheel.
Take the key to 10 and weaken the tightening of the fitting.
We remove the rubber protective case.
We put on the fitting the tube, and the other end we send to the container where the old brake fluid will flow.
Then remove the hose and wear a protective cap.
Swing the brake pedal 3-4 times with an interval of 1-2 seconds. At the same time, the air can go with the liquid. After pumping, we drag the fitting and then let go. We do so several times until the old liquid comes out from the contour.
Then the assistant presses the pedal 3-4 times the last time until it stops. We take the key to "10", weakening the tightening of the fitting on ½-¾ turnover. It should be waited until the brake fluid is solved into the container. We drain the spent brake fluid together with air bubbles in a pre-prepared bottle. When merging, we pay attention to the color and descend until the net brake fluid goes. Thus, pump all the wheels. Then remove the hose and wear a protective cap. Take the liquid to the MAX mark.
After the work, it is necessary to spin the fitting and put on the rubber protective cap.

Liquid selection

The manufacturer of the car recommends using only certified TJ corresponding to all quality parameters and technical characteristics. For Hyundai Solaris, DOT-3 or DOT-4 FMVSS116 standards is suitable. From the factory, the original "Brake Fluid" Hyundai / Kia 0110000110 Dot 4 is poured to the fill to be needed 0.7-0.8 liters. But if with full pumping and simultaneous replacement in the clutch cylinder, then you just need to take a standard liter bottle.

The level of TZH in the tank must be between the risks of "min" and "max" applied to the sidewall of the tank.

As the car is used, the level will fall. As for the topping of the brake fluid to the level, then there is a couple of nuances. It is forbidden to top up the old TZH, as it is already contaminated with impurities, filled with air, moisture.

Original brake fluid Hyundai / Kia 0110000110 Dot 4, "Brake Fluid", 1l bottle, costs 1450 rubles. You can use substitutes from other manufacturers of Fenox SBF4010 "SBRAKE"; Hella-Pagid 8DF355360021 "BRAKE FLUID". The price will be within 200-300 rubles per 1 liter.

Output

Replace the brake fluid in Hyundai Solaris on one side simply, especially those who have already conducted such a process. A newcomer This procedure may seem quite complicated for understanding, and even more so for execution, so in this case it is recommended to contact the car service.

For the safe operation of the car Hyundai Solaris, the condition of the brake fluid is important. It should be changed in a timely manner, compliance with the manufacturer's recommendations.

Make a replacement will not make a lot of work with your own hands, but the car owner still should know some subtleties of the event.

In the brake contour, Hyundai Solaris poured the original TZ HYUNDAI BRAKE FLUID. It is sold under the article 0110000110. The volume of the canister is one liter, and the price ranges from 380 to 550 rubles. Brake brake fluid refers to the DOT-4 class.

In the brake system, Hyundai Solaris is allowed to flood liquid from third-party brands. Alternatively, you can choose any DOT-4, which refers to DOT-4. The table below shows best options From third-party firms that were widely popular with Hyundai Solaris.

Table - Good brake fluids for Hyundai Solaris

Brand	vendor code	Approximate cost, ruble
Vag.	B000750M2.	290-390
Polcar	VA402402.	260-290
Honda.	0820399938	550-590
Trw.	PFB450.	120-260
General Motors.	93160363	425-610
Bosh	1987479106	150-245
ATE	03990158012	155-175
Brembo.	L04005.	145-165
Peugeot / Citroen.	469934	500-550

Replacement frequency

Replacing the brake fluid on Hyundai Solaris takes every 30 thousand km. At the same time, the DVG should be updated at least once every 2 years, regardless of the mileage, which drove the car.

This may require an unscheduled TZE replacement. The causes of this are:

periodic boiling brake fluid;
an unpleasant smell that comes from the tank with the DJ;
the tester shows the increased moisture content;
the volume of the brake fluid decreased;
the walls of the tank began to be covered;
in the liquid there are flakes or other inclusions;
mechanical damage to the tank body or its cover occurred water or another technical fluid in tzh.

If it is not possible to replace the brake fluid in a timely manner, a number of negative consequences are possible. The main of them are presented below:

loss of opportunity to stop the car due to the boiling of the DJ;
corroding of metal surfaces of the brake circuit;
piston overlooking the cylinder and as a result of the engine of the car aside when it stops;
dependence in the intensity of braking from ambient temperature.

Rules for replacing the brake fluid

Caps of fits have a small resource. They are often cracking and losing elasticity. Therefore, it is desirable to have several caps in stock in order to promptly replace the worn or damaged element.

In the process of draining the brake fluid, it should be taken into account the correct sequence of opening of fittings. This will minimize the mixing of a new and old TJ. You can view the sequence of pumping the brake circuit in the image below. The volume of extinguished TJ in this case is minimal.

The brake fluid has very significant hygroscopicity. Therefore, it is forbidden to use the TJ, which was stored in an open container. A fitted moisture significantly reduces the threshold of the Zhi's boiling. This increases the risk of brake failure during an intensive or emergency vehicle stop.

High hygroscopic brake fluid does not allow it to be reused after the drain. For the topping should be used only a fresh DUE from a hermetic container, for example, from a tightly closed canister.

The brake fluid includes the components that make it toxic. To protect the environment, it is forbidden to merge a story in rivers, lakes or land. It is also not recommended to pour out the TH in the sink or toilet. For proper disposal, it should be passed to the point of receiving toxic and hazardous waste.

Aggressively brake fluid not only in environmentbut to LCP car. Its pouring on the body can significantly damage the paintwork. Therefore, when you hit the LCP, it should be wiped as soon as possible. After that, the place of the strait is required to rinse with water with the auto-pump.

During the replacement of the brake fluid, it should be avoided using a lubrication elements. Oil enters the reaction with the DJ. As a result, Zhiy loses its initial properties and its use on the car significantly reduces driving safety.

Required tools

To replace the TJ on Hyundai Solaris, you need tools from the table below.

Table - List of tools required to replace brake fluid

Replacing the brake fluid on Hyundai Solaris

Instructions for replacing the brake fluid on Hyundai Solaris are presented below.

To access the tank with the DJ, the hood should be opened.

Open the tank cover.

Select the mesh.

Focus the old Zip.

Put the mesh in place.

Pour fresh brake fluid.

Remove the protective cap from the fitting.

Dress down one end of the hose on the fitting.

Lower the second end to the package for the drain.
Unscrew the fitting.

Press the brake pedal.
When trapped pedals, tighten the fitting.

Let go of the pedal.
Re-open the fitting and press the pedal. Repeat these steps while the hose will appear fresh brakesuha.
Dress cap. If it is damaged, replace the new one.

Fucking the TJ.

Pump all wheels.
Bring the level of TJ to normal.

Pack key of a straight line 10mm

The brake fluid is very hygroscopic, absorbs moisture out of air, which, in addition to the emergence of corrosion of the parts of the brake system, reduces the boiling point of the fluid itself, and this may lead to the failure of the brakes with frequent intensive braking. According to the recommendation of the manufacturer's plant, replacing the brake fluid follows after 2 years of operation.

Priority of fluid replacement in brake mechanisms:

Use brake fluids corresponding to the DOT-4 class.

Do not use a merged liquid again: it is dirty, saturated with air and moisture. Always fill in the system only a new liquid of the brand that was filled before.

The brake fluid is hygroscopic (absorbs moisture from the ambient air), so it cannot be stored in an open container.

Protect the environment! Do not drain the brake fluid used into the soil or sewer system.

1. Pump the old brake fluid from the main brake cylinder tank.

2. Follow in a tank clean brake fluid to the lower edge of the bulk neck.

3. Clean the air outlet valves from dirt and remove the protective caps of the brake mechanisms of the front wheels.

For convenience, you can remove the wheel.

4. Clean the air outlet valves from dirt and remove the protective caps of the valves of the operating cylinders of the rear wheels.

Air outlet valves on cars with disk rear brakes are located on the caliper.

5. Put the hose on the operating cylinder air release valve brake mechanism And immerse the end of the hose into a clean transparent vessel with brake fluid.

6. The assistant must sharply press the brake pedal four to five times (with an interval between pressing 1-2 c), and then hold the pedal pressed.

7. Unscrew the air outlet valve at 1/2-3 / 4. From the hose will begin to flow out the old (dirty) brake fluid.

Brake pedal at this time should go to the stop smoothly. Once the liquid stops flowing, wrap the air outlet valve.

Constantly follow the level of fluid in the tank, not allowing it to reduce it below the MIN tag on the wall of the tank. As the level decreases, tighten the new brake fluid to prevent air from entering the hydraulic engine. Thus, the gradual displacement of the old liquid is new without drying the hydraulic system.

8. Repeat operations 6 and 7 to full replacement Fluids in the drive (a clean liquid should be flowed out of the hose without air bubbles).

9. In this way, replace the brake fluid first in the operating cylinder of the right rear wheel, then the left front.

10. Then replace the brake fluid in the second loop (first in the operating cylinder of the left rear wheel brake mechanism, then right front)

11. After replacing the brake fluid, be sure to wear the protective caps on air outlet valves. Damaged caps replace.

12. Check the quality of the work performed: press the brake pedal several times - the pedal stroke and the force on it should be the same with each press. If it is not, go back to the execution of operations 5-10.

13. Follow the brake fluid to the MAX label level on the main brake cylinder tank. Close the tank with a lid.

Photo of tool
Stock Foto Details and consumables

Watch an interesting video on this topic.

The brake system on Hyundai Solaris has two contours, they are completely isolated from each other and are divided into parking and working. Such their uses on auto provides increased security of the car. The duty of each driver is charged to monitor their technical condition and spend the liquid on time. How to replace the brake fluid (TZH) on Hyundai Solaris will show in a visual photo of instructions.

When to change the brake fluid Hyundai Solaris

It should be remembered - hydroscopic, which causes an increased absorption of moisture from the air. This becomes the cause of corrosion of the components of the system elements, lowers the boiling point of the TJ and, as a result, the failure of the brakes with heavy loads.

It should also be proceeded to replace the brake fluid if:

changed the color to the darker or noticeable sediment in the tank;
there was a repair of the brake pipeline or a brake cylinder failed;
increase / reduction of pedal stroke, as a result, air appearance in the system.

What and how much mourning brake fluid in solaris

The manufacturer of the car recommends using only certified TJ corresponding to all quality parameters and specifications. For Hyundai Solaris, DOT-3 or DOT-4 FMVSS116 standards is suitable. The original "Brake Fluid" Hyundai / Kia 0110000110 Dot 4 is poured from the factory for filling into the system 0.7-0.8 liters. But if with full pumping and simultaneous replacement in the clutch cylinder, then you just need to take a standard liter bottle.

The level of TZH in the tank must be between the risks of "min" and "max" applied to the sidewall of the tank.

As the car is used, the level will fall. As for the topping of the brake fluid to the level, then there is a couple of nuances. It is forbidden to top up the old TZHSince it is already contaminated by impurities, filled with air, moisture.

The liquid should be addicted to the same brand and the specification, which was filled into the system.

In that case, if the need to attach the EXPLAY, should contact the Hyundai service center for troubleshooting.

Required tools and materials to replace brake fluid on solaris

Tools and consumables required for replacement of the DJ:

new brake fluid;
rag;
key size "on 10";
transparent hose and capacitance.

To quickly and successfully replace the TW and pumping the brakes, it is necessary to attract an assistant, and replacement actions to carry out on the observation pit or the overpass.

The order of replacement of the brake fluid in the system is as follows: