How to improve light headlights 2115. How to improve car headlights? After that follow the instructions

Adjusting light headlights on VAZ 2113, VAZ 2114 , VAZ 2115.

Welcome!
Shine headlights - it is necessary to regulate it, especially after buying a used car there are old owners regulate shine Under yourself and therefore, when driving on such a car, or you begin to make the eyes of the oncoming drivers, or the headlights are so lowered low, that and the roads are not really visible, well, and in fact they need to regulate them after replacing the lamps, since various lamps are shining on their own In other words, some lamps are very shine, and some are not.

Summary:

How to adjust the headlights on the VAZ 2113-VAZ 2115?

Note!
In essence, the headlight is not at all regulated on these cars, so if you take the classics, so that there are headlights to adjust, it will be necessary to take the scrolls and turn the adjusting screws with it, and on the Samara family cars, everything is simple, quite only on the hands of the gloves To wear so as not to get dirty and chalk is still stocking, it is necessary to draw the scheme on the wall on which you will regulate the headlights if you did not understand something if you have a question: "What a wall needed and for what a scheme to draw on it? " In this case, just read the annotation further and you will understand everything!

1) before starting to adjust, think about how you will do it (true either on the eye), if you don't need to draw any scheme, just screw the screws and everything (about these screws later), if you want it true In this case, first look for a flat surface on which you can put a car (asphalt perfectly) and opposite this surface should be the same strictly vertical wall as you see in the photo slightly lower, the car from this wall for you will need to put at a distance of 5 meters (not counting the walls, you can use plywood sheets or something else, you will come to mind), after which, in chalk, draw on the plywood or on the wall three vertical stripes, one of these lines as you already see the photo should be in the very center (in the central part of the car front) and go to the very end to the bottom (the line "O" is), the 2nd bands are the side (they should be drawn, strictly from the headlight center) in the photo they are still signs "A" and "B" are also the same and horizontal line 1 which also must be drawn from the headlight center and the last line is a horizontal number 2 that is indicated, it is slightly lower The first strip (650 mm.) must be drawn.

Read

how improve light headlights on VAZ 2113, 14, 15 to 20 meters

Ordinary manipulations without special abilities and light head 20 meters enlarged! Simple chip tuning. Subscription.

VAZ 2114 Make shine Headlights better.

installing xenon together with halogen lamps.

Read

Note!
But there is one but! Before all this adjustment, to start up, so that it was more clear, check first how you are pumped up with your tires, not counting this erase all the dirty with headlights so that they shine great, and also fill the car ( If there is no ability to fully fill, then the floor of the tank at least fill it out) and put behind the wheel of your own friend, or any person weighing 75 kilograms approximately, well, and in the end in the side part, roll the car so that the pendants are installed!

Oh yeah what else will need to do, the handle of the hydro-corrector headlights put in position one driver (this is a figure 0), below we secured the photo on which the handle of the hydraulic corrector is indicated by the red arrow (it was manufactured for those who do not know what headlight corrector), a given handle for you and it will be necessary to turn to position 0, it is not visible in the photo to agiveness, since this figure is on top and the highest part of the panel closes, not counting this in the photo, everything is shown on the example of the car VAZ 2110 and not VAZ 2114 therefore you have a given corrector handle a little but may differ, but explain to you in 2-minded where it is, and specifically it is located on a car with a torpedo VAZ 2114 Near the deflector in the left side (if you sit on the driver's chair), near this corrector, another handle you have going to find it after the salon own car On the driver's seat and sit down!

2) We are now overgrowing in fact to adjustment, close one headlight at your own car (using a black cloth) and then run to adjust the headlight, which is not closed with a cloth, to adjust it to adjust the hood in the car and from the back of the headlight Laying two hand screws, one of which is needed to adjust the light beam along the vertical plane (this is a screw 1), and the other horizontal (this is a screw 2), all that is indicated by numbers 3, 4, 5 in the photo you no longer touch, so Using these screws adjust shine Such a macar headlights, as shown in the photo (in the diagram means) a bit higher, and specifically pay your attention to the point "E" which appeared by the means of passing lines ("A", "B") and the bands "2".

A significant part of the VAZ owners is asked about how to improve the headlights on the VAZ 2114. This problem is found on many models of cars. It is necessary to solve it as quickly as possible. Light on the road is the key to safe movement. Otherwise, an emergency may occur.

Why maybe bad light on VAZ 2114

To solve the problem, it should be understood in all nuances of the headlights. Simple replacement Headlight may not give proper effect. In some cases, the change of lamps will be at all the cost-effective cash.

Causes of headlight fault:

1. One of the most common reasons is dirty windows. Dirt that may appear on the headlights after long operation, it is capable of worsening the light by about 50%. It also happens that notice any pollution on the headlights is quite difficult. This is due to the fact that they can be invisible. How to remove dirt from headlights? Make it may not be so simple, because it is not allowed to use a dry cloth. She leaves small and low-wing scratches on glasses, which can spoil the glass.

Recommendation. In order to wash the headlights, you need to use special tissue and detergent. Only in this case, the motorist will be able to effectively clean the headlights from all kinds of pollution. Another one to make the headlights clean - it is to put the washer.

2. Small scratches are another common cause of the fact that the headlights become dull. Scratches may appear due to a wide variety of reasons. The thing is that wiping the headlights with an ordinary cloth or even a glove, any element of clothing, you can really clean the surface of the headlight, but small scratches will also appear on it. As long as the number of scratches is small, it will not have any serious impact on the performance of headlights, but after a long time, the scratches can become so much that the headlights will be solely with dim light.
3. In some situations, glass can be burst. The reasons for this great set. On the territory of Russia and other CIS countries it can occur due to temperature. In the event that the motorist noticed any crack, then he needs to remove the block fair as soon as possible and replace it with a new one. If this is not done, then the headlight can stop working directly while driving. The consequences of unexpected light off can be unpredictable.
4. The next reason for the deterioration of light is the age of headlights. Over time, the headlights are becoming more turbid. This is due to the fact that right during the movement various small garbage, as well as sand and dust fall on the surface of the headlight. As a result, it is very beginning to appear small scratches. Despite the fact that they are practically not visible, these scratches are able to refract light on the principle of the prism. This is an extremely unpleasant effect. It is because of it that he has to change the glass. How to protect the headlight from such unpleasant consequences? IN this case It is recommended to be accumulated by their special protective film, which can be purchased in the automotive store.

How light headlights on VAZ 2114 with a faulty reflector

The light of the headlight may be dim not only due to the presence of any damage on the glass, but also due to the state of the reflector.

It often happens that the driver cannot find the cause of dull glow. And it lies in the fact that the headlights can be in an absolutely normal state, but the reflector is faulty. What do you need to do to return the head of the previous qualities? In this case, you need to replace the reflector.

How to improve light on VAZ 2114. Replacing the reflector

The reflector replacement procedure is extremely simple. Every car enthusiast can cope with it.
Action plan:

1. To begin with, you need to remove the block fair. You can do this only when the battery is turned off.
2. Then the headlights are required to remove the glass. It is attached using sealant. It softens with the help of an ordinary construction dryer. After that, the glass must be carefully pushed and removed.
3. The next step is to unscrew the bulb.
4. After that, you need to dismantle the smear reflector and put a new one. When this is done, the motorist will only remain collect the headlight with the full compliance with the reverse order.

We must not forget that before installing the glass it must be cleaned, and the body is best deguted as soon as possible before applying the other layer.

The problem with tension

Also, light can become dim due to the presence of any problems with voltage. Due to the voltage there may be a problem with light headlights. The cause of the malfunction lies in the generator.

Council. Perform any work on replacing the generator should be extremely careful, so it will be better consulted with a professional electrician.

Another cause of a malfunction is an incorrect headlight position.

It also happens that initially a person adjusted the headlights properly, however, due to any small push, the adjustment was broken. This situation is most often arising from the shock. How to improve headlights on VAZ 2114 in a similar case? For this, it will not be necessary to have any specialized optical devices, but it will have to spend a lot of time to spend so that the direction of the light flux becomes the same as before.

1. The first stage is to put a car at a distance of 5 meters from the smooth wall. Then you need to plant a person to a driver's chair, and then fill fuel tank. This is necessary in order to rather adjust the headlights as accurately.
2. Now on the wall you need to make a special markup. It is necessary to ensure that the vertical central line will completely coincide with the central part of the car, and the side markup coincided with the headlight center.
3. Horizontal marking must be carried out at the level of lamps.
4. Now with the headlights you want to remove the glass. It is necessary to provide access to the screw, which is intended for adjustment. The second headlight must be covered with some cardboard.
   The direction of light should be "fit" to the most accurate getting into the point where the straight lines are intersect. It should be remembered that the adjustment can be carried out only with the nearest headlights included. In this case, you can adjust both Middle Lights and Far.

Danger of headlights that are bad shine - you can not underestimate! Poor lighting is a reason for an accident, and as a result of injury not only the driver, damage to your car, oncoming, passing transport.

Causes of bad headlights

To this you need to strive

I look for the cause:

• Faulty lamp.
• Dirty glass.
• damaged or loud reflector.
• Insufficient voltage.
• Not adjusted direction of light flow.

Replacing dim lamp

Replacing the lamp is carried out with a screwdriver (thin) or shill. The protection box is removed by turning screws on the headlight block. Under the lid, the mechanism of the holder and the pipe is visible - the contact.

We change the lamp

The procedure begins with a shutdown of the contact pad.. Next, by pressing the fastening spring, the lamp is removed with the subsequent replacement. In parallel, condensate is removed from the reflector unit. The presence of such displays the lighting device. The removal of moisture is made through the drainage duct, after the preliminary cleaning. Installing the lamp, the assembly is carried out in the reverse order.

Dirty headlights and muddy windows

Dirty headlights reduce road illumination by 50%. Moreover, glass over time, become agitated. They contribute to the wipes with a dirty cloth, which causes microscopic scratches.

The brightness of the light of the car by 50% depends on the state of the glass headlights

Cracks are not excluded that pass dust, water (during washing). They settled on the outer, the inner surface of the glass, reflector and leads low lifesty of light rays.

Not the recoverable trail on the glasses leave dust, sandbanks, pebbles flying out from under wheels of counter-or passing machines. Scratches, microcracks refracted, dispel light in different directionsAs a result, the direction of the beam is lost.

Replacing the glass in the spotlight

The variant of the gluing transparent film is not a technical solution. Explicit access to the glass replacement.

Lamps and windows can not give effect if the reflector has shut down due to continuous operation. On the domestic cars VAZ-2114 provides the ability to replace the reflector, for which it follows:

Low voltage on the lamp

Low voltage on headlight terminals may cause weak light

Low voltage occurs due to a malfunction of the current generator, oxidation or contact breakdowns. Checking this node It is necessary that the voltage, including on the contacts of the lamp, was 13.8 ÷ 14.2 V. The weak voltage can be revealed, calling the circuit and finding a defect, eliminate.

The characteristic cause of weak headlights is often involved on auto xenon lamps.

Distorted position of the head

The wrong direction of the rays is the distorted position of the headlights.

It happens as a result of a minor impact, even a light touch of the bumper, for example, with a wall when parking, wood or burgur.

Head adjustment is accompanied by the placement of the car on a flat area before any smooth wall at a distance of 7 ÷ 10 meters. T. the direction of the ray can be obtained under the condition of the tank refilled (more than 50%), regulatoryly pumped tires. The machine is loaded as usually operated.

Two headlight adjustment screws

On the wall, the center of one headlight was written on the wall (the other is covered, for example, a piece of cardboard) and the body center. Below 12 cm is the second line. The third line is held 22 cm below the first. According to these three projections, a vertical line with coverage of the center of the headlight and body is also watched. One of the two screws placed inside the headlight is regulated by the slope of the light, and the second is formed a directional beam.

It turns out the projection on the second line. Having finished the procedure and with the second header, it turns out the adjusted Middle Light. In this case, the distant light will also be configured.

Video of headlight adjustment on VAZ

• Release the fast battery wire.
• Do not replace with the engine running.
• Take time from the moment the lamp is turned off, as it has a high degree of incandescent.
• Remove the lamp without jerks and pressing, because they are often bursting into small particles with scattering, dangerous not only for the eyes.
• Do not create congestion, stopping on the roadway of the road or sideline as a result of an unexpected disappearance of light. Follow the nearest maintenance point.
• Do not abuse the installation of xenon lamps. Such are blind by drivers of countercourses, exacerbating the occurrence of traffic accidents. By the way, in some CIS countries are prohibited.

The headlight shines low

Headlights shine "in the floor"

If the headlight shines down "to the floor", then the mechanism of the headlight hydro director is to blame. This is VAZ-2114 disease.

Headlight control knob depending on the car load

You can identify a malfunction if you change the position of the headlight corrector from the cabin. If the headlight does not change the height of the beam, the hydrocorrector is defective.

Pusher hydrocorographic

If you need to urgently go, then you can remove the mechanism of the hydrocorrector from the headlight, cut off the hose, and insert there with a plastic dowel from the nail.

According to the rules road, By car, which moves along the highway, the headlights of the near light should be included. This is definitely reduces the use of lamps, which causes their frequent failure. On the models of VAZ 2114 or VAZ 2115 lighting is used both in the day and in dark timeWhat requires vigilance and control over the integrity and quality of the lighting system.

To diagnose the lighting device in time, you need to regularly inspect your car.

We produce inspection cars

After you have found a breakdown of distant or dipped products, proceed to eliminate the problem - replacing the element. Contact specialists to a hundred or replace yourself that save your money.

The block headlight on a vase 2114 from such components:

• housing (plastic);
• light scatter;
• reflector.

On the model 2114, movable and fixed lighting systems with single or two-dimensional light bulbs can be installed.

Face block on VAZ 2114

Types of lighting devices

There are several types of light sources for VAZ 2114:

• xenon. Represented by the models of the CO glass flackwithin which gas is located (xenon). Provide higher brightness compared to currently losing popular incandescent bulbs. In the absence of lenses to adjust the flow of light, the drivers of the oncoming cars may be blind;

Xenon light bulb

• incandescent lamps. Are relatively dulls, rapidly wear out, but they are inexpensive;

Incandescent lamps for auto optics

• halogen. Presented in a wide range - from very bright models to universal (all-weather). The latter have on the inner wall of the flask the coating, providing a yellowish shade of light stream for better visibility during bad weather conditions (fog, snowfall). For example, the usual lighting system model will reflect the falling rain drops, which will dazzling the driver. And the light of the yellowish shade is characterized by a lesser reflectivity, so it does not cause irritation of the driver's eye while driving in a vase. Also, all-weather models will allow the car VAZ 2114 to be more noticeable on road covering During the weather, it will reduce the risk of an accident.

Halogen light for cars

There are 2 most popular manufacturer of all-weather halogen lighting systems:

• Kirzhach. The domestic manufacturer releases long and narrow models without the top wall and with a partition inside;
• Bosch. It has a wide reflector equipped with walls from all sides.

So that the motorists can easily choose what light bulb far Light You need to put in your VAZ, specialists in the field of automotive lighting, guided by the results of numerous tests, amounted to a list of one of the most popular types of type

H4. They are suitable for use in the neighboring or left light system on the model 2114.

The list includes such stamps:

• IPF (Superbeam model);

SUPERBEAM IPF light bulb

• Narva (model Azzurro);

Narva H4 Azzurro Rally Contrast + Light Bulb

• GENERAL ELECTRIC (ALLDAY model). The quality of the product justifies its high cost, according to car trays;

GENERAL ELECTRIC ALLDAY LIGHT

• Philips (model Weather Vision). He is the brightest model that can be installed in the near or far light system.

Philips Weather Vision light bulbs

Process changing the product

Replace the emerging component of the near or far light system for each. You will need the following tools at the same time:

• awl (thin screwdriver);
• magnet equipped with a long handle (optional).

First of all, for replacement you will need to remove the minus wire from the battery. If you do not do this, there is the possibility of getting a shock.

After that follow the instructions:

1. Open the hood when the car ignition is turned off. Find block headlights on two sides of the car.
2. Unscrew the protective box of the light source on the block phary on both sides. After removing the box cover, you will see a block with three contacts that are responsible for the power of the lighting system, as well as the spring type holder.
3. Disconnect the block, and then with the help of a squeezing fastener of the product, free the lighting element. You can remove it from a regular location for fasteners.

To replace and put in place another product providing bright light, follow the instructions in the reverse order.

Why are the headlights on the VAZ 2110 and 2114 badly? Fix I. improve

To understand and find out the reasons why shine The VAZ 2110 and 2114 does not shine well, you need as quickly as possible. Light on the road. The guarantee of your well-being after sunset, and especially in winter, when it becomes darker early (and late dawn comes). If a common topic And adverse conditions are added in the form of rain or snow, the lack of lighting becomes in the literal sense of the word dangerous.

Going almost to the touch, you risk starting with the integrity of your iron horse: the undetected pit can cause a serious damage to the working hole and even provide a drift that is fraught with wounds not only for your car, but also for offensive / passage,

Why lights on VAZ 2110 and 2114To find the reasons necessary for complete confidence that this particular factor prevents proper functioning. A simple lamp replacement on more powerful does not always solve the problem and can be an unnecessary waste of money.

Read the same way

Most likely are the most simple causes.

Dirty headlights Reduce the illumination by 50%. Wipe their dry cloth. not best idea. With this approach, at the same time, you scratch the glass, which over time will make their dull glow permanent. Do not want to regularly wash the light manually. Place the washer. By the way, in the "top ten" block from the Volga excellent. And the installation is quite simple and possible by itself.

how improve Light headlights on VAZ 2113, 14, 15 to 20 meters

Simple manipulations without special skills and light head 20 meters enlarged! The simplest chip tuning. Subscription.

VAZ 2114 make shine Headlights better.

Register and earn on watching advertising!

Glass can burst. If you notice the crack on the surface, you need to remove the block headlight and change it to the new one.

Read the same way

If the machine you have already fled well, glass can gradually dim from age. Since it is located in the front edge, when moving, dust, grain and small garbage, falling on the head chapel, leave microscopic scratches on the glass. Most of them are so small that they are not even visualized, but at the same time they refract and dispel the light in accordance with the principle of the prism. Glass must be changed; And that the next replacement moves as far as possible. You can cover it with a protective film.

If the glasses are all right, possible cause Weak glow can be irradiated reflector. No matter how powerful the lamp you screw in the headlight, you will not receive because of the brightness of the world. On most foreign cars in this case, you must completely change the headlight; On a vase, you can replace only the reflector. And the procedure is very simple:

• The headlight is dismantled when the battery is disabled;
• Glass is removed from it. It is placed on a sealant, which softened by heating with a hair dryer. Then the glass is encoded and carefully deleted;
• Light bulb is unscrewed;
• The poisoning reflector is dismantled, a new reflector is placed, the headlight is assembled in the reverse order.

Before installing the glass, do not forget to clean it and the body of the old sealant and degrease the new layer before applying.

Voltage problems: Particularly characteristic of cars that are halogen lamps. The lack of voltage can be caused by an incorrectly operating generator or oxidation / destruction of the contact. Normal shine Set at a voltage of 13.8-14.2 V, and the same should be at the ends of the working lamp. It is permissible to fall on it not more than 0.2-0.3 V at 2000 rpm.