The ignition lock is considered an important element, without which the "life" of any car is impossible. If the ignition lock is defective, it will not be possible to start the engine, therefore, the machine will not move from the place.
Therefore, the replacement of the Ignition Castle of the VAZ 2110 is in a timely as important. In addition, this detail is some kind of protection of the machine, as in the case of any lock, the ignition lock is obeying only the appropriate key.
Replacing the ignition lock on the VAZ 2110 can be carried out with their own hands. This will be discussed in this article.
Note! Today, modern hijackers will not stop the most advanced anti-theft system, the same applies to the simple ignition castle.
In fact, the ignition lock is a conventional interrupter that is blurring or closer required to function the engine contact groups. If such a node malfunction increases the risk of car hijacking.
In addition, many unforeseen circumstances are being created in an inappropriate time.
Replacing the ignition lock in VAZ 2110 machines is recommended in such situations:
- if there was an attempt to the hijacking of the vehicle, while the ignition lock was collected;
- if the car owner has lost its key;
- if the contact group has ceased to function.
In frequent cases, the vehicle does not start due to bad contacts, it can be easily checked.
Requires:
- disable "-" terminal on the battery;
- remove the casing from below;
- using an ohmmeter, disconnect the contacts and check. Such contacts should be characterized by zero resistance. Otherwise, it will takes a mandatory change of ignition lock.
What is better to replace - a larvae or a separate contact group
It is recommended to fully change the lock only if it completely stopped functioning or seriously damaged by mechanical way. In other situations, you can try to replace damaged parts of the castle.
In case of exceptional recovery of the lock, for example, when trying toft or when tight turning the key in the well, it is possible to do only by partial repair. In some cases, the replacement of the larvae in the ignition lock is quite enough.
Note! The change of damaged elements is not a challenge, so almost any vehicle who does not have special skills and knowledge can cope with it.
To carry out repair work, you need to get a necessary tool:
- hammer;
- scolder.
Step-by-step instruction shift ignition lock
Before proceeding to changing the ignition lock in the VAZ 2110 machine, you need to perform the main condition, namely de-energize the vehicle. On the battery you need to disable the terminal "-", only after such actions you can start removing the casing on the steering column.
In order to facilitate the process of replacing the larvae, it is recommended to dismantle the entire ignition lock. After replacing the element, the work lock is installed on its place.
If you consider the financial side of the issue, it can be noted that the change of contact group will be much more profitable. As in the previous case, do not do without a meal and the castle itself.
In order not to have unpleasant moments, when disconnecting the contact group it is desirable to perform the marking of all dismantled wires. Such measures will prevent confusion and save precious time.
Note! In rare cases, the contact group may be a locking ring that can be removed using sewing. At the end of the change of contact group, you need to put the locking ring in the same position.
Change of Ignition Castle VAZ 2110
To change the ignition castle "Dozens" do not necessarily have any superpowers. At the same time, ignorance of some nuances will make a little torture and tinker.
Like other repairs, the ignition lock shift is recommended, following the instructions provided:
- After replacing the details, you need to use special bolts that have tear-off heads. Most of the masters advise them to replace them with 20 millimeter bolts of the M6 \u200b\u200bbrand.
This can be explained by the fact that they are easier to remove if necessary to perform the next repair of the castle.
Note! Despite such advantages, there is also a reverse side, namely a decrease in the safe level and anti-theft vehicle protection.
- To loosen the tightening of the bolts, the chisel will need. It is necessary to use with marginal caution. In the worst case, you can cut off the head of this bolt.
- Before changing the ignition lock in the VAZ 2110 machine, you need to insert the key into it, turning into the first position. Such measures need to be performed to enter the locking housing of the latch-lock, which blocks the steering shaft mechanism.
- After such actions, the ignition lock can be put on the steering column, while it must be fixed with the screw and clamp new bolts for fastening.
- After removing the key from the well well, it is necessary to make sure the functionality of the power steering shaft block functionality. If the shaft lock for some reason does not work after turnover, you need to adjust the location of the ignition lock on the steering column.
Note! Actions continue until the latch falls into the appropriate groove.
- If as a result of adjustment, the locking mechanism still does not work, you need to use the 10th-size cape key, with which the bolts are delayed. Bolts are neatly tightened before the position until their heads break.
Of course, you can repair the car in the car service, but if it comes to small repair, for example, changing the ignition lock in the VAZ 2110 machine, it can be done using video and the photo on your own. This is a simple procedure, which requires a minimum of knowledge, skills and time.
With repeated replacement, the instructions cannot be needed. Since the price of repair at a hundred consistent, independent actions make it possible to save significantly, the main thing is to acquire high-quality spare components.
