Like the other parts of the machine, the generator belt also flashes over time. In this situation, there are some tips on terms.
Replace the VAZ 2110 generator belt must be strictly on time when it is wearing. VAZ 2110 8 valve generator belt or 16 cl. You can replace with your own hands.
This will be discussed in this article.
Important moments
Thus, on VAZ 2110 machines, you need to change every 45 thousand mileage kilometers. This figure is not final, it is specified approximately and depends on the operating conditions of the car.
For this reason, you need to check the belt for the integrity every 10 thousand kilometers.
Note! It is worth noting that the wear belt that has been replaced for the reason that "time has come" is still operational, you do not need to throw it away immediately, let it be as a spare element.
The proper functioning of the entire node is more affected by the tension of the timing belt. For example, if after changing the belt, the generator begins to pull, then most likely, the belt is simply pulled.
If the element slipches, it can talk about its irregular tightening.
Of course, to replace the belt, in principle, as for shifts, some spare parts are needed with tools. When buying a spare element, you need to know the dimensional belt parameters, while it is desirable to give preference only to known manufacturers.
Device and adjustment of the generator belt
As a rule, for the functionality of the machine, little fuel in the tank, also not to do without electrical energy. If the internal combustion engine is provided by the generator, electricity is independently performed.
The pulley of the end of the crankshaft shaft of the motor is binding to the pulley of the generator shaft using a belt transmitting rotational movements. For uninterrupted and efficient belt transmission, the tension of the generator belt is performed to some extent.
The timing belt tension indicators are designated by machine manufacturers.
Of the existing ways to adjust the belt tension, the manufacturer of the VAZ 2110 model assumes the most reliable design without auxiliary rollers. In this case, the tension is performed by removing the generator from the motor by means of a special bracket with a tension bolt.
Note! In fact, the procedure for stretching the belt is not difficult, it can even make a novice car enthusiast. But, despite this, you need to have the skills to adjust the degree of stretch, since the scroll of the timing belt can be removed in this way.
To the belt possessed the necessary adjustment, it is recommended:
- disable the battery terminals;
- through a wrench, weaken the upper and lower fastener nuts of the generator (see);
- turn the tensioning bolt along the clock arrow, achieving the required stretching (when pressed, the deflection must be respected between pulleys equal to 10-15 mm);
- the fasteners of the generator nuts are well delayed.
Note! If it is impossible to carry out actions at a time, the adjustment must be repeated, but before that it will require the rotation of the crankshaft of the motor. Make 2-3 turns and check whether something has changed.
The simplest change of timing belt on the VAZ 2110
For its short life, the generator belt transfers significant mechanical loads, so it is not surprising that it is quickly wearing. In frequent cases, it is broken, but this is due to the excess of its operation.
As a rule, the mileage of the machine between each shift should be no more than 50-60 thousand kilometers.
In fact, the procedure for replacing this detail does not provide special difficulties. For these repair work, you need to get a pair of wrench keys and, of course, a new belt.
Changing the timing belt on cars with gur
For example, with an external examination of the belt, it was revealed that there are cracks, then do not do without mandatory replacement of this part. In this case, the generator belt passes through: crankshaft pulley, tension roller, generator shaft, pump shaft GUR, crankshaft pulley.
As a result, the belt is scrolled on the left around the motor support. To remove it, you will need to unscrew the support and lift the engine, only after that the belt itself is removed.
Works must be performed in this sequence:
- the generator belt is weakened, the motor support is unscrewed:
- unscrew the pulley of the gur, which when shielding is removed. As a result, you can easily get the support bolt of the engine;
- the engine is raised, while it is unnecessary to remove the crankcase protection. To implement such a procedure, it is recommended to use the bottle jack. It will have to work only through a hole designed to drain the oil.
If it is understood using a wheeled jack, you need to remove the crankcase; - the support nut is easily dismantled, after which the generator belt is drawn (it is dragged through the support).
The subsequent installation of the timing belt is performed in the opposite instruction of the order.
Note! If the item does not replace on time, the work of the entire car will break.
For a successful self-replacement of the timing belt, you need to buy the necessary sizzy. For the VAZ "Dozens" enough length of 1115 millimeters.
Such a belt must be provided with six streams.
Note! The belt tension is of great importance.
If it is insufficient, it will increase the wear of the element and the recharging of the AKB will worsen. In the case of an excessive stretch, the breakdown of the generator bearings will accelerate.
Replacing the timing belt on cars without gur
Naturally, if there are any failures in the functionality of the machine, it is necessary to find the causes of such behavior. For example, checking the battery needs to be done if problems for the electrical part appear (lighting, etc.).
The belt malfunction can be revealed by estimating its tension. The weight of the belt located between the generator and the crankshaft, during an effort should be fed at 15-15 millimeters.
If such a fact is not observed, you need to correctly check the tension. To implement it, you need to weaken the upper and lower fastener nuts of the generator.
Only after that the equipment is removed from. With such measures, you can safely adjust the belt tension.
If it needs to weaken, you need to turn the adjusting bolt against the clock arrows.
Note! Replacing the timing belt is better from the bottom of the machine, so it is necessary to raise its top and remove the protection of the crankcase on the engine.
To perform a replacement, it is necessary to weaken the tightening of the engine fasteners, turning the adjusting bolt. After that, the generator equipment is moving to the maximum to the cylinder block, and the wear belt is dismantled.
Of course, you can repair any problem of car in terms of car service, but minor repair work is better to perform with your own hands with your own hands, it also concerns the replacement of the generator belt on the VAZ machine. Step-by-step instructions will help even a newcomer motorist.
Performing independent repairs, there is a high probability to save money because the price of repair per hundred is far from democratic.
