In the car VAZ 2109, the castle of the back door changes very easily. It is not necessary to turn to a qualified master.
All work can be made independently at home, having your right tools and a desire to repair yourself. The lock mechanism does not constitute anything complicated. Its installation, as well as the subsequent adjustment, can be performed by an ordinary driver.
When is the replacement of rear door locks on VAZ 2109? In two cases: if the lock refuses to work because of the breakdown, or when the key loss.
The most frequent castle malfunctions
Faults of the castle in which it is required to replace or repair:
- the retainer fell, which joins the tag of the central to the door lock;
- the refraction of the wire, during the repair, you will have to find the place of the cliff, and then restore the wiring;
- the failure of the executive mechanism.
On VAZ cars, the principle of replacing the castle of the rear door is not different. Therefore, the instruction for replacing the VAZ 2109 will be the same for other cars of this brand. To confirm the simplicity of work at first, the replacement of the trunk lock on the VAZ 2109 will be considered.
Replacing the castle of the trunk
In a specialized store, this item is sold complete with larvae. However, a certain prudency is required here. It is impossible to pull the key from the larvae, because the mechanism can fall apart and collect it again, most likely, so simply will not succeed.
In order to gain access to the trunk lock, first need to remove the panel, which is fixed with plastic rivets (hedgehogs). If you find these devices under the hat, they are easily pulled out. Often, the hedgehogs are cleared, so best when buying a castle to purchase them too. You need to remove all rivets to easily and conveniently remove the panel. After completing the replacement, the rivets can be inserted, pressing the finger on them.
After the panel is removed, you need to unscrew the nuts on the old castle, and then remove the lock itself. After that, a new one is inserted into a free space, and the nuts are twisted. It remains to put the panel and insert hedgehogs.
Setting the clamp
If the bottom of the luggage compartment lock and the retainer does not change, then no settings are needed. Otherwise, when replacing, the new retainer must be configured for the convenience of opening / closing the trunk.
To configure, we should weaken two bolts in front, and then close the luggage compartment. The record as a result should tune himself. After that, you need to open the trunk and tighten the bolts.
It happens that after setting, the latch selects the clock curve. In this case, you have to check whether the trunk is well closed. If everything goes smoothly, you don't need to touch anything. Otherwise, you need to independently find the best place for the retainer, moving it.
Castle back door
Before, the replacement of the lock on the back door of the VAZ 2109 should be carried out, it should be the first to remove the cover with the door.
Removing the trim
- Remove the bolts of the old device.
- We screw the hairpin into the place of the bolt so that the inner side does not fall inside the door.
- Remove the old castle and put on his place silent.
- Spin the bolts with the greatest effort, but to be protected by a shock screwdriver.
You can also install silent bolts and fingers of the retainer.
After installing a silent device, it will be necessary to adjust. The adjustment procedure is the same as described above. Here you also need to tighten or loosen the screws depending on the movement of the mechanism.
Trying not to damage the adjustment of the retainer, you will have to put a gasket from a polished waterproof skirt. With the help of such gaskets, you can adjust the distance between the rack and the retainer. This procedure is done in order to prevent the finger touch on the outdoor lock cover.
In conclusion
As you can make sure, replace the castles of the rear doors on the VAZ 2109 with your own hands is quite simple. All that is necessary for this accuracy and patience. In particular while adjusting the new installed mechanism. And if you have to change the old keyboard mechanism on a new one, experts recommend setting precisely a silent model. It will avoid unpleasant metal clang during door closing. Well, of course, after installation, the part must be properly and neatly set up.
