The castle of the trunk and the larvae in the doors of the VAZ can easily be changed at home by itself without resorting to the help of masters. The lock and the larva change when the key is lost or the lock does not work.
I will change the castle of the trunk and the larvae of the doors on the VAZ 2109, but since in our vases the principle of replacing locks and larvae is the same using the described instructions for replacing the lock and larvae, you can apply to any VAZ brand.
The trunk lock is always sold together with the larvae of door locks, below the castle photo with larvae. But be careful, do not pull the key out of the castle larva, if you pull the key from the castle larva, the lock mechanism will crush, it is very difficult to collect it correctly. I'll start with the replacement of the trunk lock, but you can begin with the replacement of the trunk lock of the machine and the replacement of the larvae door handles, the choice is yours.
Photo. Trunk lock and door larva
Replacing the Castle of the VAZ Trunk
To get to the trunk castle, you need to remove the panel, it holds on plastic rivets (they are also called hedgehogs). These rivets can be pulled out a screwdriver under the Hat, it happens that they break, it is better to immediately buy new rivets and not worry about the broken hedgehog. Below the photo on it is shown two rivets, but it is necessary to remove everything, then the panel will take off. Pulling rivets by pressing the finger.
Photo. Arrows showing rivets that need to be removed
It remains to unscrew the old castle of the trunk, the photo below shows the nuts that need to be unscrewed, put a new lock, tighten the nuts back, the lock changed.
Photo. Arrows are shown nuts that need to be unscrewed to remove the trunk lock
Usually, if you do not change the lower part of the trunk lock "Fixator", then it is not necessary to configure it. If you change the door lock lock, then it must be configured to close the trunk easily. The lock is configured so, loosen the bolts that are shown in the photo below, close the trunk, the lock itself is adjusted under the lock, open the trunk, tighten the retainer. It happens, after this procedure, the fixer becomes crooked, relieve it, try to close the trunk, closed well, excellent. If it is bad, then find a small movement to the retainer so that the trunk is closed well.
Photo. Arrows showing the trunk lock adjustment bolts
Replacing the larvae of the castle VAZ
Of course, it sounds frightening, replacing the castle larva, actually the operation is very simple. First you need to remove the upholstery of the door in the photo below shows how to do it. Remove the steering handle, unscrew the door handle bolts, two bolts in the lower door pocket, the lock switch button.
Photo. Arrow Showing Castle Handle Handle Glass Door
After that, having rolled up the courtyard of the door to remove it from the rivets of the hedgehogs, if the car visited other hands, then additional screws, screwed into the skin of the old owner, are possible, find them, unscrew. The lifting of the door is removed, you can easily reach the door of the door and the doors handles nuts.
Photo. Show how to remove the panel with the door
To remove the door handle, you need to unscrew the two nuts, they are shown in the photo below, be sure to raise the glass to the very top, then it's easy to unscrew the nut inside the door, save the thrust of the handle from the castle, see them well to see it looks inside the doors.
Photo. Door handle mounting nuts
Now you can easily remove the handle with the door of the machine, it remains to replace the larvae of the lock, below the photo with the subsequent operations to replace the castle larva.
Remember how everything is worth it, then easily collect everything right. Remove the plastic leash of the lock switch from the castle larva, in the photo the arrow shows the installation of the pin, it can be easily pushed with a seboard or carnation. Remove the spring from the larva, now the old larch can be easily pushed out of the door handle, insert a new larva with the key. Collect everything in reverse sequence.
Photo. Replacing the larvae of the castle
To replace the locking mechanism, you need to unscrew two bolts on the mechanism itself, the outer and inner part of the lock mechanism will be released, it can be changed to a new one, or rinsed and lubricate the old one. But be careful, always watch and remember how it costs, then there will be no problems when assembling.
Photo. Mechanism of the door lock
Replacing the Castle of the VAZ door. Video.
Why, after replacing the lock, the door does not open with VAZ 2109?
You may have forgotten to snap the castle on the lock, or you need to adjust the locking of the lock (unscrew, lengthening the craving).
Fig. Lock of the front right door: 1 - leash key; 2 - leash of the lock switch; 3 - shutdown traction; 4 - exterior drive; 5 - key; 6 - lock button lock; 7 - Tail off button; 8 and 17 - shutdown levers; 9 - outer handle; 10 - Bracket internal handle; 11 - inner door handle; 12 - facing of the inner handle; 13 - internal drive traction; 14 - the hull of the inner castle; 15 - external drive; 16 - intermediate lever; 18 - body of the outer lock; 19 - Castle Drive Finger; 20 - dog; 21 locking lock; 22 - ratchet; 23 - Castle fastening screw
Fig. Fastening the door lock: 1- screw fixing lock; 2 - nut mounting of the outer door handle; 3 - lock button lock; 4 - outer door lock; 5 - Lightworker
Fig. Top Door Castle 1 - Bolt Fastening Clamp; 2 - cross-rear; 3 - retainer; 4 - hook spring; 5 - hook; 6 - Castle case; 7-cylinder castle drive assembly; 8 - Rear door; 9 - door opening seal
Gorobinsky S.V.
