You can say with great confidence that without a generator car will not work. And in order to understand this, you do not need to be an auto mechanic. As practice shows, the most common belt comes out, which is rapid enough. It begins to "whistle", which indicates insufficient tension and its slippage. But more often it is necessary to replace the Bearings of the VAZ-2110 generator. Let's talk about this and talk.
Bearing of the VAZ-2110 generator
Before proceeding directly to the repair work, you need to perform a number of preparatory activities. For example, remove the generator, clean it from dirt and dust, if necessary, wipe with pure rag. Before dismantling, do not forget to disconnect the "minus" from the battery. Immediately note that there is an front and rear bearing of the generator. Most professionals recommend to replace in the complex, this is how we will do. In principle, this is a reasonable solution, since the replacement of one bearing will not improve performance if the second is on the verge of destruction. From the tool you will need to "8", as well as the usual flat screwdriver. It is advisable to have a horn key with you, the usual head to "27" and deep to "19". This should be quite enough, so the replacement of the Bearings of the VAZ-2110 generator should not cause problems. And now let's consider step-by-step instructions for removal.
How to remove and install the rear bearing of the VAZ-2110 generator
Before proceeding with the work, mark the marker with the help of a chalk location of the rear cover. Please note that dismantling is performed with the stator winding. Now we use a special filler; If there is no such, it will suit a large horn key. They need to hook the bearing and try to get it. But the problem is that if he is tightly sitting, and it should be, then it is necessary to apply the hammer. We move the bearing on the key to key, while it does not come out of the landing place. After it is dismantled with the shaft, you can install a new one or repair the old one. Again, the installation is carried out with a tension, so it will take all the same remnant or key. Light blows need to press the bearing on the shaft and check that there is no backlash. Now go to the next step, which is practically different in difficulty.
Disassembly of the front bearing and its installation
At the first stage, it is necessary to carry out a similar procedure for labeling the cover (front). Do not forget to do this, as then a lot of time will go to the adjustment. Now you can remove it with the key to "8". It is enough to unscrew 4 bolts. Using a special filler and hammer, knock out the bearing. Please note that if you plan to repair it, then you need to do it carefully, without destroying the outer ring and rolling body. Before putting a new, lubricate the seat. This is necessary for several reasons. First, without lubricant material, the stability of work deteriorates, the temperature increases and increases and this is already elevated wear. Secondly, the lack of solid lubricant leads to a screen. As for the installation, you can use the old bearing. It must be put on a new one and with the help of a hammer with neat blows to press.
A little about repairs
In 90% of cases, the Bearing Bearing of the VAZ-2110 generator is an empty occupation. Now you will understand why it is. The fact is that the bearing is not so expensive, but at the same time a fairly responsible and complex in the manufacture of the part. A break can lead to unstable work. The only thing you can do is apply lubricant and clean the landing place from foreign inclusions, such as dirt, etc. In principle, the replacement of the Bearings of the VAZ-2110 generator does not take much time. It is difficult to say how much you will have the strength to perform this work - much depends on the presence of practical experience and brand of the car. But after you make it this once, then it will be easier.
Conclusion
If you heard a strange hum, it is likely that it is in the bearings, but do not rush to go for a new set in the store. First you need to check. First of all, it is required to make a visual inspection, see if there are chips, jackets, corrosion traces, etc. Even if the crack is noticed, you need to change the bearing. Go to the store where you can buy the Bearing of the VAZ-2110 generator, the dimensions of which are selected by the old sample or number. How to install it, you already know. Do not forget to check the pulley for the presence of defects, as this is a very important point. There should be no tangible backlash, but also moving on the shaft should not be difficult. On this, the replacement of the Bearings of the VAZ-2110 generator is over, check if the problem disappeared. If so, we did everything right, if not, then we are looking for.
