During the operation of the vehicle, problems always arise with malfunctions. It is necessary to identify them in time, repair.
On the VAZ 2110 noise in the gearbox can be called several reasons. On VAZ 2110, the noise of the gearbox can be easily eliminated and on their own.
The reasons
If the car is in the parking lot, and the speeds are not included and the noise is listening to the engine, it means:
- the bearing of the primary shaft bearing occurred and it is necessary to replace it in time;
- below the level - to check, add, when the fifth speed is turned on, a whistle occurs, and this will soon affect the rest of the gears;
- the oil does not match the recommended viscosity - it can be called moisture, a dipstick to check the color of the oil, there may be pale splashes - it is necessary to replace the oil.
If the gearbox is noise when performing movement:
- acceleration of movement when the gas supply is increased from 1 to 5 speeds, it may also occur when the speed drop is caused by a malfunction of the main pair and it is necessary to replace it;
- when turning on 3, 4, 5 speeds, the metal grinds - a malfunction of the upper bearing of the secondary shaft;
- the first speed turns on, the metal grinding increases, the box subflines - the lower bearing of the secondary shaft is defective;
- minor weak sounds are permissible - the gear arroga occurs after assembling the box.
Tip: It is advisable to diagnose the CAT at the maintenance station.
- With a reduced oil level, it is necessary to check if it is not led.
- Also blow the Sapun.
- Plore the oil to the level on the dipstick between the maximum, minimum tags.
- In case of water from the water composition, blessed divorces appear in the probe oil.
Merge oil with checkpoint:
- Works carry out on a heated engine, from the observation pit.
- Prepare a five-liter container.
- Unscrew the tube to drain the oil, substitute the cooked container.
- Wait when strokes all the oil.
- After that, the plum's place will wipe.
- Split a plug into place.
- Pour fresh oil on the recommendations of the manufacturer.
Tip: Install the mudguard on the engine. On the Sapun gearbox to install a rubber hose - output it up, in an inaccessible place for moisture.
Repair of gearbox
If, after performing all the work, noise in the box continues to remain, then it is necessary to remove the box, its disassembly. This must be done to eliminate the causes of metallic sound.
On the VAZ 2110, the gearbox mechanical design has five speeds of the front and one rear. With 1 to 5 speeds on the shafts, synchronizers are installed, designed to softly switch.
The whole design is connected to the differential and main transmission. The composition of the housing is collected from three parts of the crankcases - they are cast from duralumin metal.
In addition, from:
- clutch;
- gearboxes;
- separately rear cap cap.
The assembly of parts is made on gasoline-oil-rack hermetic composition. In the lower part of the crankcase, a magnet is installed, which collects a metal chips into the precipitate.
When pluming warm oil - this precipitate goes with the product being drained.
Dismantling gear
To remove the box, you need to prepare the tool and auxiliary materials:
- caid key number 10, №13, №17;
- heads №13, №17;
- two mounts;
- plumbing hammer;
- gorotok;
- five-liter tank;
- rag;
- metal brush;
- acetic acid;
- gloves x / b.
Note: Before starting work, it is necessary to remove the minus terminal with the battery.
All dismantling work is held in the observation pit.
Rules for removing the PPC:
- remove the engine mudguard;
- disconnected reactive traction and drive thrust;
- merge oil with gearbox;
- unscrew three bolts with heads for 10 from the bottom cover of the clutch crankcase;
- remove it;
- remove the drive of the right wheel;
- in the resulting hole in insert a piece of rubber hose or a wooden tube - it must be done from protecting garbage;
- unscrew the nut with a nutac;
- dismantle the ball support;
- the swivel fist with the rack is assigned to the side, the drive is removed from the hub (it should be installed on stretching).
- Mounting carefully remove the housing of the internal hinge from the checkpoint.
Note: When the case is notched, try not to damage the protective ring, which is located on it.
- Remove the left drive.
- Disconnect.
- Remove the power supply chips from the reverse lamp switch.
- Disconnect speed sensor.
- Unscrew the fastening of the fish, it is attached to a nut at 17.
- Remove it.
- To the engine put the spacer rack.
- Disconnect the left support of the engine.
- Disconnect another back support from the box.
- Lower the spacer rack.
- Unscrew from three bolts, nuts that fasten the clutch crankcase.
- The box exempted in this way is to remove.
- Remove the box from under the car.
- Rinse it, eliminate water from entering the device.
- Clear well from dirt, oil layers.
- Metal brush to go through places of compounds, carefully clean the bolted connections.
The repair of the gearbox is desirable to trust spending masters from the car service, as it represents a complex design. Experienced qualified specialists will produce quality repairs.
Replace the necessary details. Verification of the unit will be conducted on a special bench.
At the end of work, specialized workshops are always given a guarantee.
The installation of the box is carried out in the reverse order:
- Pour the oil recommended by the manufacturer's plant for use in the transmission of this particular model.
- After installation, it is necessary to adjust the stroke of the clutch pedal.
- Check speed switching on.
- Adjust the gear lever, choosing the working parameters of the scenes.
- Check the box work while driving.
Tip: It is necessary to conduct a timely check of the oil level in all operating units of the vehicle.
Identify the reasons for the noise of the gearbox on the VAZ-2110 after watching the video, the study of photo materials. Get acquainted with the attached instructions.
They specify places that will help the motorist to identify all the subtleties during the operation of the car. The car presents a construction of many systems, aggregates.
Therefore, it is necessary to gradually study the accompanying materials. This will largely help the motorist during the operation of the car and the box, which should be switched smoothly and comfortably.
After reading the above material, motorists are unlikely to have a question - what is it? The instruction will also help determine the reasons for noise and to repaired everything in a timely manner.
The price for the work on replacing and repairing the checkpoint is not so low, in connection with which, you can try to do everything yourself.
