Very often, the dashboard of a 2110 VAZ car fails. At the same time, there are sometimes problems with its illumination.
Some people just don't like the way it shines at night. In this case, it is advisable that the backlight be replaced.
This article will discuss how to independently replace the backlight of a new sample on the instrument panel, the operation of which can be seen in the corresponding video review on the Internet.
Replacing the backlight on the dashboard
To do this, you need to use the following algorithm:
- Remove the panel.
- The designation of the backlight is determined by special LED bulbs. To replace the backlight, these bulbs must be removed.
Note: this must be done very carefully, because they are quite small. In addition, it is possible to damage the panel itself.
- But before that, you should disassemble it. This is an easy task, since to disassemble it, you just need to press the latches, so you can remove the bulbs.
- Everyone saw that on top of the dashboard there is a "sticker" and designations (speed, amount of gasoline). It keeps on glue, so to remove it, you have to "dig deeper".
Remains of glue must be removed.
- You can start replacing the backlight.
Note: It is advisable to choose not very bright colors that strain the eyes. White or blue colors are ideal.
- To remove the light filter located on the back of the "sticker", you need to take a clerical knife. The light filter is located under the protective layer. First you need to take it off. Do not press too hard with the knife, as necessary parts may be damaged.
Note: It is easier to remove it if you rub it with a knife in one direction, then in the other.
- To insert LED bulbs, remove the board located in the plastic case. There will be special holes for them.
Note: but that's not all - you will need to solder the wiring of the bulbs to the board in order for them to work.
- Now you need to put everything back together and install it correctly.
Separate arrow illumination
If you want the arrows to glow in a different color, you can do the following:
- Remove the dashboard.
- Disassemble it.
- Place individual LEDs under the arrows.
Note: in this case, the arrows will light up in a different color only when ignited.
How to change the backlight using color film
In order to change the color of the dashboard illumination, it is not necessary to change the LED bulbs.
To do this, you can simply:
- Take 12 LEDs and an LED strip.
- Remove the light bulbs from the base and insert one LED in their place.
- You need to take the required amount of LED strip.
Note: its length is measured by the size of the panel.
- The base and LEDs must be returned to their original place.
- Stick the tape to the plastic of the panel (the appropriate temperature must be maintained).
- Tighten the block well.
Panel check
If the dashboard has been disassembled, then it needs to be checked.
For this:
- It is necessary to press and hold the reset button.
- Switch on the ignition.
- All arrows should go up. This should happen three times.
Note: if all arrows are working correctly, then they will all go up. Otherwise, you need to disassemble them.
How to remove arrows from the panel
If the arrows do not work, then you need to remove them and put them back, as they may be incorrectly installed:
- Grab the arrow.
- Start twisting it counterclockwise.
- In this case, it is necessary to slightly pull it up.
- Replace and check if they work.
How to assemble and disassemble the panel
To reset the speedometer or fix a problem due to which the direction indicator light on the panel does not flash, it must be removed.
To this end, you should perform the following actions:
- You can remove the cover, but the board will still be locked.
- You need to take a Phillips screwdriver and use it to remove a few more bolts.
- Now you need to snap off the latches on the panel. You should start from the bottom. If they were disconnected from the bottom side, then you can push them up. So the fee will be quickly charged.
- Arrows for any will need to be removed.
Note: some arrows are easy to remove, but the arrows of the gasoline indicator are much more difficult to remove. To remove the arrows, you need to gently pull on them.
- The panel is disassembled, now you need to try to solve the problem.
Note: There are very small LEDs on the board which may burn out too. Because of them, the turn signal light may not flash, so they need to be replaced.
This requires work with a soldering iron.
But if the panel was disassembled in order to reset the speedometer readings, then:
- Find the black button for daily mileage on the board.
- Click on it.
Now it is advisable to somehow reassemble the panel.
This is made even easier:
- Place the board in a plastic case.
Note: It is advisable to have a clean cloth underneath so that its surface is not scratched.
- Now you need to screw in the bolts on the panel itself. They do not yet need to be completely tightened, since you must first put the arrows in place.
- Before putting the arrows back in place, they must be thoroughly wiped off, as under the influence of light, prints, dirt, etc. will be visible.
Note: the arrows should be set approximately 3-4 mm below zero. It is also important that there is a small gap between the arrows and the speedometer, otherwise they will jam.
It is much easier to install, as well as remove, long arrows. To install short arrows, you need to be very careful, as they are more delicate than long ones.
- Before you put the glass, you also need to wipe it. Now snap onto the latches.
- Fasten the board with bolts.
- Last but not least, screw in the screws on the cover, then replace all the bulbs.
Working with the panel in a car is probably the easiest thing that can be. Therefore, it makes no sense to go to a car service, where the price even for such a trifling work will be high.
It is better to review a bunch of photos and videos before deciding to do the repair and tuning of the car interior with your own hands, so as not to harm the car. Any instruction will help you to quickly and efficiently do the job.
