How to install a central castle on the classics 1
A car with a proud title "Satellite", and for your just "nine", older than some of those who own them. However, this does not mean that he is something worse than modern auto industry representatives. Just you need to put a little soul in it, make it more comfortable in use, secure. So, for example, far from all cars in this series is a central lock, which allows you to close all the doors automatically, with the press of one button. Installation of the central lock on the VAZ 2109 is not a complex, but very real. If you have no desire or the ability to do this in the service, you can easily handle yourself.
Installation of the Central Castle on Zhiguli
There are several options for controlling the central locking: a separate button inside the car, the alarm keychain, and key fobs with vykutal keys that are included in almost any central locking. Since we consider the variant of the car on which the alarm is not installed, then two methods of control remains: key chain and button.
For reasons of convenience, it is recommended to use both options, as it is not very comfortable to use the keychain when the engine is turned on or on the go. That is why the central castle on the VAZ 2109, as well as ways to manage, we will look at two versions.
But before proceeding with the installation, you need to purchase a central castle.
Complete set of central castle
The Central Castle includes:
- Four electric motors. One of them has 4 power output.
- There is a terminal switch on it. That is this engine subsequently we will install on the driver's door. On the remaining three two conclusions - / +.
This device consisting of semiconductor diodes and relays will be responsible for controlling all locks.
Also, in the standard set of the central lock you will find wires, planks, fuses, etc. Now we are ready to set the castles of VAZ 2109.
Installation of the mechanism
First you need to remove the trim from all doors. Also do not forget to remove the plastic panels between the doors. It is there that will be wiring. Next, prepare the openings for wiring in the rear doors, in the front they are provided. We install the knitting needles in the rods of gearboxes, only after that you can start the installation of engines on the door.
Installation of the central castle
The point is left for small. I pull the wires to our chief control unit, which is located on the driver's door. Please note that you need to think in advance how you will behave from the right rear door to the driver. After connecting to the central unit, you can check the entire scheme. If there were no problems and everything worked, congratulations, you coped.
Installing the button of the central lock
You already know that the locks on the VAZ 2109 can be controlled using the button inside the car cabin. Any button that performs the function of the window on VAZ 2109 will fit as such a button.
Further installation must be made according to the scheme:
Connection diagram of the central lock button
To connect the button, you must find the required wires under the onboard panel of your car. We need black, brown and white. There is an option to use a beam of wires from the driver's door. The most we used to install the central castle.
But sometimes when trying to connect to them, problems arise, all doors are triggered, except for the driver. In this regard, we recommend that you do not waste time, but immediately connect to the wires under the torpedo of your car.
Wire connection, Installation of the Central Castle button
Connect them according to the scheme, and it remains only to cut the button at a convenient place for you. Connect the wires of the backlight, cut the required hole in the panel, and insert the button into place. This completed the installation of the central castle on the VAZ 2109. The photo is higher, we hope you helped.
Adjust the door lock on VAZ 2109
If the doors of your four-wheeled beast are poorly closed, or they open it tightly, then it's time to do it closely. You can change this situation by adjusting the door retainer.
Important! A water-resistant peel is installed under the door lock. It will help not disrupt the position of the lock and perform the function of the gasket.
It is due to the laying of the skirt that the distance between the retainer and the counter is controlled. Thus, the retainer does not hide the cover of the outer lock.
In principle, adjusting the Castle of the door VAZ 2109 is quite simple. If the door dangles and moves, the retainer must be tightened if there is a tight, then on the contrary to loosen. The same logic is applicable if the door is loosely adjacent. The main thing is to determine exactly how much centimeters and in which direction it is shifted.
For more accurate adjustment before adjustment, it is recommended to mark the place where the retainer is located.
Adjusting the door lock
It must be remembered that in any case the gaps between the body and the door should be the same.
Install the trunk castle
Those who at least in his life were a car similar to VAZ 2109, remember that in the cold season, the trunk can be forgotten in principle. If the trunk lock has not yet rusted, then it is most likely frozen. And the most interesting thing comes when he freezes on the way. That is, you arrived at the cottage to replenish your inventories, and by returning home your favorite "swallow" to openly refuses. Or, on the contrary, you are coming satisfied with your affairs, and the lid of the trunk will have independently open, you have to stop and correct.
At such moments, the desire to put the Castle of the VAZ 2109, which will allow you to open the trunk automatically. And not to suffer, jumping around it with defrosting, screwdriver or ropes.
To install the trunk lock, we will need:
- The castle itself;
- Castle's response;
- Button;
- Any electrical drive;
- Bulgarian, pliers and nippers;
- 4 bolts;
- Metal cable and one long wire.
Installing the castle of the trunk from viburnum on the VAZ 2109 is considered the most successful option. The most important point in the installation is fitting the lock according to the size you need, so that he himself rises well, and the castle tongue did not rest in the trunk lid. To do this, use the Bulgarian.
Next, we use the rear janitor's motor for connecting the electrician. We establish a retaliatory part of the trunk, it must be perfectly approaching, as it does not differ in size from the one that you have stood before. The only one may have to hit the hammer a couple of times, as the protrusion is possible to the left of millimeters by 5, not more.
Well, now we close the trunk and check the performance of the castle. If the door walks a little, it is worth tightening the washers or relate to loosen.
