Rubber door seals VAZ 2110 are often deformed and settled, it leads to the formation of looser and even gaps. Eliminate excess noise and precipitation in the salon can only replace these elements.
VAZ 2110 doors seals
When developing domestic cars did not pay due attention to their comfort, often foreign sounds are heard in the cabin and moisture occurred during precipitation. Replacing the seals of the doors of the VAZ 2110 and slightly, the improving the best indicators of noise insulation.
Serial rubber products designed to seal the cabin, as a rule, do not differ in high quality. The problem occurs not only with two-door seals actually doors, but also lowered side glasses.
This is due to the poor quality of polymeric materials and rubber, from which these elements are performed. Errors are possible when they are installed on the conveyor, as well as deformation during long and intensive operation.
Work on the restoration of the tightness of the salon is simple and will not require a lot of time even with an unprepared employee.
Little information about the structure of the body as a whole and the doors of the car VAZ 2110
Unlike previous models of the Volga Automobile Plan, dozens no protruding over the doors of the drain. This makes the car more attractive and more modern, but it causes a number of problems associated with the need, better performance of the insulation of the internal volume of the cabin from external adverse effects.
Performing a set of measures to restore the tightness of doors
As the experience of operating machines "Tenate" series shows, used rubber elements are not too reliable and require additional refinement. The official investigation by repair provides for the replacement of these parts when deforming and destruction. Most often, such phenomena are observed at the bottom of the threshold.
The following spare parts, tools and accessories will be needed to perform operations:
- the seal is three-chamber with a fixing insert from the steel strip,
- disposable pistons for fixing elements,
- tube silicone or polyurethane diameter of 8 mm,
- screwdriver with flat and curly slots,
- figure self-adhesive profile gasket.
You can buy everything you need at any automotive spare parts store, currently there is an opportunity to choose between products of various companies. Seals are predominantly sold on a footing or ready-made sets.
Before going to the store, measure the length of the front and rear doors of the car, and buy the required amount.
Preparation for the work on the sealing of the cabin
The front and rear doors of the VAZ 2110 are a similar design of places of contact with openings and in order to unify the same sealing rubber profiles are applied to them. Before starting repair work, you should prepare all the necessary materials and accessories..
The procedure for performing preparatory operations is as follows:
- We clean the doorway from contaminants, especially in its lower part, this can be done using water and detergent or dry using a rigid polymer brush.
- With a screwdriver with a flat sting, remove the plastic facing panel from the threshold, the action takes carefully in order to accidentally do not break the fastener's pisps.
- We dismantle the old seal, simply removing it from an overdue place with the help of breeding agents.
- We re-operate the operation to eliminate pollution and garbage, which is invariably poured in hidden cavities with intensive use of the machine.
- The curly side sealing element is glued, the descendant should be removed if possible neatly without damage to the paint layer.
- Degreased overdue space is performed using special solvents that do not harm coatings.
Working surfaces are prepared, and you can start the main operations on the installation of the seal. These are quite simple actions, however, they require a certain skill.
If there is no confidence in your abilities, you can charge them to professional craftsmen. You can watch the video and try to independently perform the work shown.
Installation of sealing elements
First of all, it is necessary to perform several uncomplicated actions on the revision of the standard seal. As already mentioned, factory parts have a small resource and quickly deform. Introduction to the cavity of an additional depreciable part.
The sequence of work is such:
- With a roulette, we measure the length of the seating area and cut off the required amount of the seal with a small margin.
- Insert the polymer tube across the entire length without tension and also cut off the surplus. This element will give greater elasticity of the design.
- The seal starts to wear on the edge from the starting point, which should be located 25-35 cm from the bottom of the threshold. Installation can be guided both clockwise and in the opposite direction.
- The figure profile is sedentible with a wooden or rubber hammer until it stops. Having passed throughout the circle, we will see that part of the sealer turns out to be unnecessary.
- Cut off the unnecessary residue in such a way that the joint is without the gap and at the same time caused deformation of the adjacent sections.
- We install the Piston and mounted plastic facing in place.
- The second outline is glued along the edge of the door. We carry out this action with all possible accuracy so as not to have detachments or disorders of the form.
Installation is over and if it is made correctly, then when closing doors, a change in the nature of the sound is noted, it becomes more deaf. In addition, a metal knock is disappeared in castles and aerodynamic noises while driving at high speeds.
Tip: As practice shows, spare parts Vazpri such improvements provide reliable sealing of the cabin.
Replacing glass frame sealing elements
Polymer elements external under the influence of moisture, solar radiation and dust are gradually destroyed and need to be replaced. The phased guide to replace seals is as follows:
- dismantling the old elements with a screwdriver, trying not to damage the coatings,
- elimination of pollution under old lining and wipe the seating with a ragwork,
- we establish new seals to the places, while trying not to strike and make great efforts.
Having finished all the work on the same door, and go to the next one, if you consider that their design is similar, then there are no other features in them. So consistently removing the natural ventilation of the car's interior. Photos with step-by-step operations allows you to fulfill all actions to quickly and get good results.
Additional noise elimination operations in the salon VAZ 2110
As statistics shows, most Russian drivers do not suit the increased noise in the car. This is caused by the use of hard polymeric materials of low quality and not sufficiently reliable fastening elements.
Therefore, the bulkhead of the cabin even the new car is the most commonly demanded service at many maintenance stations. All work can be performed with your own hands, if you carefully examine the guide to carry out the entire required cycle.
Qualitatively isolating the body from extraneous noises can be only as a result of a complete disassembly.. Panels are removed, in places of their pairing, glue polymer or spongy inserts that will prevent the occurrence of the knock or other sounds.
The price of materials and works is relatively low, respectively, the total cost of work will be acceptable.
The car improved in this way becomes more comfortable and convenient for operation, both in the conditions of the city and on the track. The quality replacement of the VAZ 2110 door sealer eliminates the aerodynamic noise and the flow of moisture during atmospheric precipitation into the car's salon.
