The onboard computer of the VAZ 2110 injector is needed when problems in the car work are observed. It is with it that you can quickly and easily determine what cause is the problem of the injector.
The on-board computer on the VAZ 2110 is a device that greatly facilitates the management of the vehicle, but as any system has its drawbacks and advantages, which will be discussed below.
Differences between the injector and carburetor
In fact, the injector is practically no different from the carburetor. They almost the whole design is the same.
However, if we assume that the injector carburetor replacement will not bring any benefit, then this is not the case.
Consider the advantages of the injector:
- If there are some problems in the car, you can find them in just a few minutes.
Note: Nevertheless, you have to go to the car service where experts will diagnose the state of the machine through.
- Even at idle the engine works as needed. And in the winter, you can start the car without problems without warming the pre-engine.
- And in general, the car goes much better. At the same time, it spends much less fuel, if you compare it with a carburetor model.
- Periodically, the carburetor should be cleaned and adjust, while the injector does not require almost no intervention.
Note: Spare parts for the injector are a little more expensive than carburetor, but the injector is much stronger breaking. Just observe the rules of operation by the car.
Usually a new injector (see) works for a long time. And even if it breaks for some reason, it can be taken to the car dealership, where the repair will be produced free of charge, as it will be warranty.
If some sensor is broken, then it is possible to replace it in a matter of seconds. Yes, and there are such details inexpensive.
Disadvantages of the injector
The main disadvantages of the injector include:
- The catalyst that is located at a distance of 0.1 m above the ground.
Note: Therefore, it is necessary to ride a car very carefully, as the catalyst can be easily damaged. Especially this situation is possible when driving on uneven roads. In addition, it is worth a lot.
- Since the old model engine installed on the VAZ 2110 is not designed for the injector, it is very difficult to get to some parts.
How to ride the car with an injector
You can give several important tips for operating a car with an injector:
- It is necessary to carry out maintenance on time.
- Filling the car follows only the recommended fuel from the manufacturer.
- Sound insulation is needed, as the injector works quite loudly.
- The body should be treated with anticorros.
Note: Processing is necessary for the body to be corrosion.
Advantages of onboard computer
The on-board computer of the injector is able to independently check the condition of the car.
Many it is installed on their car, as:
- It shows the correct, so the driver can always know when he needs to fill the car.
- There is a voltmeter and tachometer.
- Works the reminder function of the oil replacement.
Note: It costs no more than 2000 rubles, but it performs a lot of useful actions.
The problems that the computer announces:
- During the operation of the car, problems may occur: a light bulb that signals the malfunction in the engine may light up (but the computer works fine).
Note: It is possible that this light bulb lights up due to a small closure, so it is not advisable to go to the car service every time it burns. Diagnosis is expensive.
- The machine consumes too much fuel. Sometimes it can be consumed even more than the maximum limit - 12 liters.
In this case, only the controller firmware will help. This process is better to entrust only high-quality specialists, as it must be completed correctly.
Installation
Before starting the installation of an on-board computer, you should pay attention to the connection scheme.
Its installation occurs in several major stages:
- Remove the terminal coming from the battery.
- Find a block on signaling (see) and get it. It is to it that the on-board computer will be connected.
- Remove the orange wire from the seventh contact.
- In its place, fasten the red and white wiring, elongated from the side of the side computer.
- Disconnect the orange wire and set it into the connector from which the wire was previously removed.
- From the tenth contact, disconnect the red wire with black stripes. To install the red wire from the harness. And to connect the red red and black. That is, the wires need to be swapped.
- From the fifth contact to pull the black wire. To attach the black wire of the harness to it.
- Connect the black wire pads here.
- From the eighth contact to remove the white wire and connect to this connector white wire of the harness. And vice versa.
Note: There should be a contact between the wires.
- Now you should check whether the wires are well fixed. The place of their twisting should be isolated using an insulating tape.
- Through the inside of the console, the harness needs to be stretched to the installation site of the on-board computer.
- Connect it to the sensor regulating the fuel level in the machine.
- Remove the instrument panel by getting access to a gray block.
- Disconnect the fuse block.
Note: It is installed on the left of the driver.
- From the gray pad, you need to pull the pink wire, which gives the signal to the fuel sensor. It is necessary to connect a pink harness wire.
- Install on-board computer.
- Enable ignition and check how it works.
Our instruction will help you install the on-board computer to the car with your own hands. The approximate price of the on-board computer ranges within 2000 rubles.
For the work of the car lock, you will need to pay about 2,000 rubles. Therefore, you can save, having done all the work yourself.
Before you start work, you should consider photos and videos on a given topic.
