Many car owners believe that tuning must first allocate and emphasize its presence. Therefore, all that will be found on the car in the local car market. But you can do something and useful and comfortable. And first of all for yourself. To make it nicer to drown time in the car, stand with cold and snowy winter evenings in traffic jams. Increation will surely immediately think about changing a terrible low or rattling high torpedo on a foreign one or something from this opera. But after all, on a torpedo and instrumental pvnel, we just look, and contact directly with the wheel. Of course, you can go to the local car market and buy yourself instead of a frankly wretched standard steering wheel (both old in the spirit of a century and more new with a big signal) New Turkish or Chinese. And with screaming inserts with red or blue. But you will not be surprised that the skin is zero there and that after some time it will cut down, gets off, etc. ...
We offer to your reflection such refinement as a hauling of the helm of the skin, and at the same time the installation of the steering wheel. The latter is very relevant for residents of the northern regions, and such decent. Although you can restrict ourselves and simply crawling the helm of the skin. And if you have cold winters or very cold winters, then WPare with autorun This refinement is generally a fairy tale. He came out of a warm house, sat down in a warm car, took up the warm steering wheel ... I think it's not necessary to convince anyone that even if the salon is warm up 15-20 minutes, then the rim of the steering wheel does not warm ............ .....
Earlier, we have already published an article here. Now, we publish a similar material for the owners of "Chisel" with a high torpedo.
If we consider the sad glory of this torpedo as the most rummy, it is quite easy to understand why the owners of these cars are ready to spend a lot of time to silence it. The removal of high torpedoes has almost 2 times more steps than the removal of low .............
VAZ is such a car that every owner trying to make it at least a little better, sooner or later comes to the conclusion that you need to remove the torpedo. In order to sneak it from a screen or sample the wall of the engine compartment with vibroplast. Either to decide on its replacement at all ... there are enough options!
Disconnect the wire from the terminal "-" battery. Install the wheels in the position of the straight movement. Disconnect the carburetor air damper lever and the speedometer drive cable from the gearbox ...................
Each owner of the car VAZ 21099 wants the salon of his vehicle to be comfortable. Therefore, looking at the photo of tuning details, many people have a desire to make tuning of the VAZ 21099 panels with their own hands. By the way, after it, all the veneer screensions usually disappear, for which the owners of domestic "nines" are complained so often. As a result, the driver can enjoy silence, as well as hear the rust of tires along the asphalt surface and a pleasant whisper of the motor.
Tuning salon VAZ 21099 is better to start equipping the bottom of the bottom of the body with solid insulation.
And the improvement of the dashboard should go after strengthening door facing. The fact is that it is the doors that are usually the main source of creak.
Steering wheel handles should not interfere with traffic safety
The steering wheel in the VAZ 21099 is quite safe and quite comfortable, therefore there is no sharp necessity in its replacement. Experts recommend only to establish a leather braid on it to improve the appearance, as well as the quality of contact with the driver's hands. If you have to get rid of the old steering wheel, they should be visited by the automotive market, where you can always find a wide range of sports "Baranok", both Chinese production and famous firms.
It is not necessary to get used to the tuning torpedo to the VAZ 21099, since some design innovations can interfere with driving safety. These include square shape or reduced steering wheel diameter and ruptures in the steering wheel: they will be useless in the case of an extreme situation on the road.
By tuning the salon VAZ 21099 with their own hands, it is undesirable to add additional handles to the steering wheel. This, of course, looks spectacular, but does not allow maneuvers with jewelry accuracy. Despite the fact that the instrument shield similar to the part of the spacecraft looks great - you can't argue with it.
Do not regret money on tuning salon VAZ 21099
Do not regret money on a complete ceiling, body racks and doors, use high-quality leatherette. After tuning the instrument panel of VAZ 21099, you can proceed to the tightness of the gear shift and "handbrake", as well as the rear shelf and the steering column.
Pads on gas pedals, brakes and clutches will be quite by the way, and the installation of anti-slip floor pay will add both practicality and originality the appearance of the cabin.
Spare parts for tuning can always be found in local stores, on the car market and on the Internet.
Complete a peculiar symphony of the car tuning VAZ 21099 will allow convenient chairs with lateral support. Especially beautiful when these seats are made in a sports style, and their design is designed in advance for installation on "nine" powerful sound speakers, which will enjoy listening to high-quality music.
On the topic of tuning the backlight of the VAZ 2109 dashboard, a variant of the LED backlight without serious interference in the tidy was considered. There, we simply replaced the lighting lamps on the LEDs, so the effect is though there is, but over time I want more. Waiting for more comes down to the fact that on the following generations of the Samar tiedings and on foreign cars of the dial dial are highlighted from the inside, and it looks like the numbers themselves and the devices themselves. The panels of the same devices of VAZ 2109, VAZ 2108 highlight lamps, emitting their light on the dial outside, from the side of the arrows, while the brightness and detail of such a highlight is low.
Let's try to backlight the instrument panel from the inside, as on foreign cars, on the example of the high panel of the VAZ 2109. It should be noted that the tuned tidwings in specialized firms are very expensive, so you can save well by improving the instrument panel with your own hands.
To do this, we will need a lightweight pad on the instrument panel, like this:
Remove from the car and disassemble the instrument panel, remove the arrows of the instruments and remove the old lining. In order for the light of the backlight to fall on the overlay from the inside, make cutouts on the surface under the overlay. This can be done with a heated knife or soldering iron.
Now we make the backlight itself. It will be organized on the basis of LED tape. We use a tape that is cut by pieces of three diode. For uniformity of the glow, we make a reflector from a conventional foil.
For a speedometer and tachometer, we take 3 pieces of tape, on the pointers of the level of fuel and the temperature of the coolant, there is enough one piece.
Staten backlight, save, as it highlights the arrow of the instrument scales. It can also be upgraded by gluing the LED tape lamps to the regular place, a little toned it, otherwise the backlight will be unnecessarily bright. You can toned with a tint film, or a black marker, as described in this article. It is desirable to leave a regular light filter at the same time, the backlight light will be soft and uniform, with a slightly bluish tint.
All this backlight is connected to the contacts of the layout of the standard backlight lamp, pre-determining their polarity. To stabilize the current, when writing the LEDs, you can use
Earlier, we have already published an article here. Now, we publish a similar material for the owners of "Chisel" with a high torpedo. If we consider the sad glory of this torpedo as the most rummy, it is quite easy to understand why the owners of these cars are ready to spend a lot of time to silence it. High torpedo removal has almost 2 times more steps than the removal of low ...
As in the case of a low panel, we will perform work related to the electrical equipment of the machine, which means the first thing to remove the terminals from the battery.
1. Remove the decorative steering wheel lining.
2. Remove the steering wheel fastening nut so that the ends of the nut is flush with the end of the steering column shaft.
3. The steering wheel sits very tightly on the slots of the shaft, so do not turn away immediately the wheel fastening nut: with a sharp blow steering wheel, jumping from the slots, can cause injury. Stitch the position of the steering wheel relative to the shaft.
4. Hands with harsh strikes Run steering wheel with steering slots
5. Finally unscrew the nut and remove the steering wheel.
6. Unscrew the six screws for fastening the bottom of the steering column.
7. Remove the bottom cover of the steering column and cladding the ignition switch.
8. Remove the top horn of the steering column.
9. Loosen the tightening of the bolt of fastening the base of the submissive switches.
10. Remove the base from the shaft and disconnect the two pads with wires from the sound signal contacts.
11. Disconnect the block with wires from the wiper and washer switch lever.
12. When disconnecting the pads with wires, we recommend to march them. This will avoid confusion when assembling and save your time.
13. Disconnect the shoe with wires from the rotator and headlights switch switch.
14. Pull the handle of the carburetor air damper (samples) so that the thrust appears, and remove the handle from it.
15. Remove the two screws of the appliance panel console fastening screws.
16. Remove the lining from the console.
17. Remove the cigarette lighter cartridge from the nest.
18. Remove the ashtray from the nest by clicking on the plane to clean the cigarettes.
19. Remove the heater fan switch knob.
20. Remove the three heater control knobs, making them with a screwdriver.
21. Disconnect the block with wires from the heater fan switch under the heater control panel.
22. Disconnect the two wires from the contact panel of the heater backlight.
23. Remove the head of the headlight hydrocorrector, pulling it on.
24. Remove the instrument combination lighting switch knob.
25. Unscrew the fastening of the instrument combination lighting switch.
26. Unscrew the headlights of the headlights hydrocorrector fastening nut.
27. Push inside the panel switch lighting switch combination and headlight warhead.
28. Remove the side nozzles on both sides of the instrument panel using a screwdriver.
29. Unscrew one-sides of the instrument panel on both sides of the instrument panel.
30. Picture the outdoor lighting switch from the panel.
31. Disconnect the shield with wires from the outer lighting switch. Push the block inside the instrument panel.
32. Picture the screwdriver and remove the magnetic socket. If an audio equipment is installed on the car, you first remove it.
33. Magnitol remove in accordance with the instructions of the manufacturer.
34, unscrew the screw fastening of the instrument panel lining.
35. Insert two screwdrivers to bend plastic latches.
36. Lift the instrument panel cover.
37. Disconnect the shock with wires from the cigarette lighter pad.
38. Disconnect the block with wires from the cigarette lighter backlight pad.
39. Disconnect the block with wires from the emergency signaling switch illumination.
40. Disconnect the block with wires from the alarm switch and finally remove the instrument panel lining.
41. Gently press down and remove the loudspeaker cladding on the left side of the instrument panel. Be careful - the latches are easily laid out.
42. Disconnect the shoe with wires from the heating door heating switch.
43. Remove the block from the rear fog lantern switch.
44. Unscrew the two screws of the instrument combination.
45. Remove the combination of instruments from the panel, screw the fastening nut and disconnect the cable from the speedometer.
A warning
Disconnect the pads with the wires of additional equipment if it is installed on your car.
We will take tuning of the instrument panel VAZ 21099. First of all, we dismantle the plastic, we get to the panel board, we delete it, but about everything in order. In the process of refinement, we will need a soldering iron, insert in the dashboard of the VAZ 21099, ultraviolet light bulb, some wiring, regular bulbs with cartridges, glue and fluorescent marker.
We will start work. So, remove the panel, we remove the glass and the edging of the plastic around it, gently take out the arrows and insert. Pay attention to your new insert if there are no holes, they will have to do themselves. It is recommended to do each hole with a small margin, in order to prevent the arrows sticking. It can be said that at this stage half of the work is made. We dismantle the regular backlight, we do it carefully, we try not to break the fragile plastic. We take out a fee from this place. It is better to make a circuit of connecting and connections so that you will not forget what to join. Instead of a regular backlight, we will install neon light bulbs. We glue neon to the panel and on top we glue plastic protection, where there were regular light bulbs. Make sure that the design keeps securely and will not fall off at the first touch. On top of the panel glue the neon lighting control unit. You can glue the unit as glue and bilateral scotch.
Connection is performed in the place where the standard backlight was previously. Do not confuse polarity, on the board is usually noted where minus and where plus. If there are no such marks, we define it with an experimental way. Next, we take a pair of light bulbs on each device, for example, on the Speedometer VAZ 21099 we connect light bulbs on both sides and connect all this with wires. Wires stretch from the inside, having done small holes in partitions. Installed light bulbs, connect them there, where neon light bulbs are connected, it is not worth paying attention to the polarity here, it does not play any role. Now check the lighting for performance if you are all done correctly, you can attach a lining and start admiring. Additionally, correct the position of the bulbs from the inside. By the way, the fastening of the bulbs from the inside can be performed with the help of glue, you only need to make the wiring prevent the movement of different parts of the sensors, the wiring can be glued to plastic elements. Almost everything is ready, go to the final stage. We put the lining on top and in the corners planting it on glue. The pad is on the spot, go to the installation of the arrows. Installation We produce extremely gently, paint them with a marker, it is advisable to dry them several times. It remains to assemble the dashboard and put everything on your regular places. In mandatory, check the operation of the sensors, collect torpedo to the end. This is just one of the options for tuning the instrument panel of the VAZ 21099, it all depends on your capabilities and fantasies. It is quite realistic not to buy a lining, but paint with your own hands, thereby make the original tuning of the car's salon. The main thing - the backlight should only illuminate the panel, and do not make you in the face, so it is so important to choose the right bulbs and adjust them.
