How to change side light bulbs. How to replace a side light bulb? The traffic police will punish you. How to replace a side light bulb - dorestayl

Replacement may be a little difficult due to the special headlight. Therefore, you may need a surgical instrument.

Such a trifle as replacing a side light bulb on a Hyundai Solaris, for cars of other models, can cause certain difficulties. Especially if you have no experience in servicing the machine yourself. Solaris also prepared a surprise when servicing the optics, but dealing with it is quite simple.

Ratings of side light lamps

Marker bulb in the headlight.

The Hyundai Solaris front headlights are equipped with:

• halogen headlight lamps with H4 standard socket, power 60/55 W,
• 21W turn signal lamps РY21W ,
• side light lamps with a power of 5 W with the designation W5W .

The design of the headlight block allows you to quickly replace any of the lamps, but on the driver's side, access to the left headlight is complicated by the fuse box.

You can use diode lamps.

Several years ago, official Hyundai dealers began offering special plastic tongs, with the help of which replacing the size lamp is easier. However, even without them, the operation can be performed in a couple of minutes with your own hands.

Replacing the side light bulb on a Hyundai Solaris

Before replacing the side light bulb on a Hyundai Solaris, you must disconnect the negative terminal from the battery to avoid a short circuit. We will start the replacement from the right side, where access to the headlight unit is not burdened by anything.

The operating algorithm is as follows:

1. Remove the plastic cover on the back of the headlight unit by turning it counterclockwise.

   Removing the headlight cover.

2. We gain access to the halogen double-filament headlight lamp, side light lamp and turn signal lamp.

   Gained access.

3. To replace the side lamp, it is necessary to remove the lamp socket from the headlight housing by pulling the wires towards you.

   Old and new marker lamps.

4. The socket is returned to its place in the headlight and the plastic cap is put on.

To replace the left side light bulb on a Hyundai Solaris, we use the same algorithm, with the only difference being that it is better to use surgical clamp .

In this case, you do not have to remove the fuse box, and for convenience, you can only remove the plastic cover on this block. In some cases, if it is necessary to replace the headlight bulb on the left headlight, unscrew the two screws securing the headlight unit. This allows you to move it forward as much as possible and easily replace any lamp in the housing.

At the end of the video

Happy lamp replacement and bright lights on the road!

February 5, 2018

Driving a car with inoperative “dimensions” is prohibited by the rules - any traffic police officer who records such a violation has the right to issue a fine to the driver. To replace a side light bulb that has burned out and gone out, you do not need to visit a car service center - every car enthusiast can perform this operation. The following instructions describe how to make the replacement correctly.

When is the replacement made?

Vehicle manufacturers do not provide clear regulations for carrying out this work. There are only 3 reasons why car enthusiasts change their side light bulbs to new ones as needed:

1. The light elements have failed - they have burned out or gone out due to external mechanical influence.
2. The owner of the car decided to install more modern LED bulbs.
3. The lights began to shine too dimly.

The first reason is clear and does not require explanation. Installing LEDs is a useful operation, since these elements shine well, last a long time and consume much less electricity. The main thing is to maintain the polarity of the contacts during the replacement process, otherwise the new light bulb may fail or the fuses will begin to blow.

As a rule, a car enthusiast does not pay attention to the decrease in the luminous flux of running lights until he replaces one burnt-out headlight bulb. Then it becomes noticeable how much dimmer the old element burns than the new one. The reason is the internal darkening of the base glass from settling metal particles emanating from the heated spiral. Therefore, it is recommended to update old “dimensions” in pairs.

To replace two side light bulbs, you do not need to create special conditions and drive the car into the garage - the work is carried out in any convenient place. What to do:

1. Disconnect the negative terminal of the battery.
2. Remove components and parts that block access to the headlight units from the engine compartment.
3. Remove the plastic protective caps covering the rear parts of the blocks where the light fixtures are located.

To change the side light bulb, you need to get to the headlights from the rear, having first removed the interfering elements. Depending on the make and model of the car, there may be an air filter housing, a battery, cooling system pipes, and so on near the headlight units. Decorative plastic panels and trims should also be removed.

Instructions for replacing lamps

Inside the headlight units of different cars there are 2 types of lamps and connectors - old and new (restyling). Replacing a pre-restyling type side light bulb is performed as follows:

1. Once you reach the back of the headlight, disconnect the power supply connector to the light element. There is no need to disconnect the sockets of powerful headlight lamps.
2. Grasp the connector and rotate 45–60° counterclockwise. Remove the element from the slot.
3. Carefully pull the light bulb out by the base without rotating it around its own axis.
4. Insert the new one in its place, making sure that the contacts line up correctly.
5. Connect the wires and check the functionality of the new part, then reassemble the unit in the reverse order.

Note. On different vehicle models, old-type elements can be rotated in different directions - clockwise and counterclockwise.

When installing a purchased lamp, you should not touch the base with your bare hands, as warned by the instructions included with each product. Before installation, wrap the glass flask with a soft rag or put on cloth gloves.

Updated versions of elements differ in overall dimensions and installation method. Replacing the lamp is done in the same way, only you do not need to disconnect the connectors and turn the socket - the part is removed from the socket along with the wires.

Another thing is that access to the light bulb is often limited - you cannot grasp the socket with your hand. In such cases, 2 options are practiced:

• use a special tool;
• First pull out the large headlight bulb, then take out the side light bulb.

The owners of some cars use the free space behind the headlights to install a gearbox that operates in liquefied gas engine power systems. Removing the unit to replace the lamp can be quite difficult.

Changing the light elements of the rear “dimensions” is much easier. The main work is removing the plastic and fabric trim from the luggage compartment side. The light bulbs are removed from the sockets in the manner described above.

Replacement of all headlight lamps on VAZ 2104, VAZ 2105, VAZ 2107

Welcome!
Headlight block. it has many lamps built into it, from the lamps that are responsible for the low beam to the turn lamps and lights, there is nothing difficult in replacing the bulbs, so a person who has not even repaired the car. In this business, the main thing is to know where the light bulb should be (we will talk about this later in this article today).

The note!
To change the lamps or any individual lamp, you don't need any tools, just pack your gloves and that's it!

Read also

Summary:

Where are the lights in the headlight?
In the classics, namely the fourth, five and seven in the headlight, the block of all lamps is three, the first is responsible for the dimensions (this lamp is indicated by a red arrow), the second comes with two H4 threaded ones, and it comes on both the low and high beam (when remote control, only one filament in the lamp lights up, and therefore the headlight begins to illuminate the road better), well, and the third. in the place that we indicated with the green arrow for you, even this is not explained, because you will already understand that this is a turning lamp.

The note!
Knowing the approximate location of the lamps, you can already understand figuratively where they are on the back side of the headlight, thereby finding the lamps will be more convenient for you and, by the way, we will immediately warn you when the lamps are exposed, do not touch your glass part with your hands, otherwise thick hand marks will initially become very hot, and eventually the lamp will simply fail, this will all happen within a short period of time, and therefore the lamp may not work even during the day, as an option, use clean gloves to make greasy marks on the glass part of the lamps. Don't leave it, or if you still leave it, gently wipe the glass with a clean cloth dampened with alcohol!

When do I need to replace the bulb in the headlight assembly?
Since the lamp is a halogen and two filaments, it may refuse to work with either the low beam (one filament fails) or the other (the second filament fails), or it may burn straight away and no more light will be produced at all (both filaments the lamps have gone out), if you notice something from this (the light has almost disappeared or become much worse), then do not hesitate and replace the faulty lamp in the headlight, but we were only talking about the halogen lamp, there is another one in the block, namely the gap lamp , this is very important for a car in the dark with ducks, since the side lights show the size of the car in the dark (that is, they are located on each side and other drivers can see the car if it is on the side of the road), it needs to be replaced if it lights up, but, as practice shows, parking lights are very rare on classics, and the last lamp, the turn lamp, it is also replaced when there is a malfunction and you will immediately notice that the lamp will stop burning, turn it when it turns, it should turn on.

Read also

Replacing the main and side lamps on a VAZ 2107

VAZ dimensions.

LED lamp for front dimensions VAZ

In this video I will show you how to do it right change light bulbs in the instrument panel to LED! The classic is sick.

How to replace a lamp in a headlight with a VAZ 2104, VAZ 2105, VAZ 2107 ?

Replacing low and high beam lamps, as well as a side lamp:

It is not easier to replace, first you need to open the hood, after which you can immediately start replacing, to do this, twist the cap and remove it immediately (see small photo) when you do not have excellent access immediately to the two lamps, namely halogen lamp and to the general one, to get the halogen, disconnect the terminal block from it (indicated by the red arrow) at the beginning and then pull the lock (it is metal, look closer, you will see it immediately, it looks like a shackle), and take it out of the lamp , and after you can also remove the lamp by simply pulling it, the new lamp is installed in the reverse order, now let's say a little about the parking light bulb, it is even easier to change, just grab the cartridge with your hand (indicated by the blue arrow), and then pull behind the cartridge, you need to pull out the lamp, and when it is in your hands with the cartridge, you must press the lamp (press it in inside the cartridge) and turn it counterclockwise, and it will come out of the cartridge more.

Read also

Replacing the lamp:

In the new classics (this is the one we are disassembling) bulbs of type A12-21-3 (P21W) are installed, when you buy them you must indicate the marking, otherwise they will not suit you, they are changed in the same way, under the headlight unit you must will stand on the back side, and there you will find a protruding cartridge, next to it there is a hydraulic corrector for the installed headlights (indicated by a red arrow, this was placed exclusively on cars in 20005, approximately, and even on early models it was present), so this cartridge is necessary will rotate counterclockwise, and you, together with the lamp, from the headlight unit, and then turn on the lamp (in the same way as a side light bulb rotates, that is, it will have to be pressed against it and rotated counterclockwise, see the small photo, this the lamp is inserted into the cartridge in the reverse order).

Replacing lamps in the front headlight unit of Daewoo Matiz

Breaking the spiral of light bulbs is a fairly common occurrence; in this report I will write how to replace burnt-out front parking light bulbs on a Daewoo Matiz. These instructions can also be used to replace lamps head light, the only difference is in the lamps used.

I decided to use light-emitting diode (LED) analogues of lamps, not only because they are low-power, but primarily because, according to the manufacturers, they have an incomparably longer service life compared to conventional lamps. During the process I took several photographs, which I suggest you familiarize yourself with. 🙂

From tools and materials we will need a Phillips screwdriver and a lamp with a W5W base. For head light You will need a lamp with an H4 socket.

First of all, you need to remove the plastic cover holding the front headlight unit. To do this, you only need to unscrew one screw, using a Phillips screwdriver.

Rice. 1 Removing the plastic cover

The headlight unit is held in place by three 10mm bolts. It is easiest to unscrew the one that is in plain sight; the other two, located under the front of the headlight, are more difficult to unscrew.

Replacing a lamp in a Daewoo Matiz headlight

If for some reason you have not yet been to the World Matizov channel, I highly recommend checking it out first

Headlight Matiz: lamp replacement head light

How to replace light bulb in the headlight head light Matiz? Watch the next master class from Mir Matizov! Useful

Rice. 2 Bolts that need to be unscrewed

After all the screws are unscrewed, we remove the headlight unit from the mounts, which allows us to gain access to the rubber plugs that prevent moisture from getting inside the headlight.

Rice. 3 Block headlight Daewoo Matiz in the extracted state

We disconnect the power wires and see the back of the lamps. Lamp side lights is removed together with the socket, and the lamp head light held by a clamp.

Rice. 4 Back of the lamp head light

We replace the lamp with a new one and repeat all the steps in the reverse order.

Rice. 5 New / old lamps for comparison

Rice. 6 Lamps head light now look yellow compared to LED dimensions

Rice. 7 Appearance at night

To ensure visibility of the vehicle during parking and braking in the dark, side lights are used. They are available both in front and behind the car. As a rule, side lights are equipped with low-power lamps that are not in the focal point of the reflector. Powerful LED or halogen lamps should not be installed in side lights.

For more detailed information on how to select and install, read the material from our specialist.

Reasons for replacing the side light bulbs

Replacing lamps in restyled and pre-restyled cars is different. As a rule, in the first case, replacement is somewhat more difficult. Nowadays, replacements do not need to be made so often because LEDs have replaced the old incandescent lamps.

However, there are situations in which replacement is definitely worthwhile.

1. You want to improve the appearance of your car and get brighter bulbs. It is worth remembering that LEDs combine well with cold xenon.
2. You want to increase the life of your side lights. LEDs have a longer lifespan than incandescent bulbs.
3. You want to reduce the amount of electricity you consume or simply keep up with current technological trends.

The reasons for the lamp malfunction may lie in a manufacturing defect. Cheap Chinese lamps quite often fail before the stated end of their service life. Also, the malfunction may be hidden in the car’s electrical network or a leak in the headlight.

How to Choose Suitable Replacement Parking Lights

You can choose a suitable lamp both in car services and at car flea markets. At the same time, experienced drivers do not recommend purchasing cheap Chinese products, since the likelihood that they will burn out ahead of schedule is quite high.

When choosing a light bulb, you need to pay attention to the following characteristics.

1. Brightness. This is the most important characteristic of a light bulb, which is assessed by its luminous flux. Luminous flux is measured in lumens. For an incandescent lamp this value is approximately 50 lumens. Remember that the purpose of side lights is to inform other road users of the size of your vehicle. Light sources should not dazzle other road users, but at the same time they cannot be too dim. The upper threshold of luminous flux for side lights is 150 lumens, and the lower threshold is from 50 lumens. Traffic safety sometimes directly depends on the brightness of the side lights, since failure to inform in a timely manner that your vehicle is starting to slow down can lead to an accident.
2. Design. In the design of cheap Chinese light bulbs, the base is made of plastic. In this case, there is a high risk of melting, since plastic is by no means a heat-resistant material. If the part gets very hot, the plastic begins to melt and, as a result, the light bulb fails too early. More expensive models feature high-quality plastic that is heat-resistant. With increased brightness, the incandescent lamp begins to produce heat, which heats the lampshade. Therefore, recently the most popular are baseless lamps, the contacts of which are made on the basis of a glass plate and a sand board. Incandescent lamps are also very energy-intensive. With increased electricity consumption, fuel consumption begins to increase. When choosing a light bulb, it is also worth remembering to save energy.
3. Price. The side light bulb is one of those car parts that you definitely shouldn’t skimp on. By buying lamps at low prices, you run the risk of replacing such lamps too often, and in the end, such “savings” will only lead to more serious expenses. It is best to purchase lamps from trusted manufacturers such as Osram and Phillips.

How to replace the side light bulb in restyled models

Before replacing a light bulb, it is advisable to place the car on a relatively flat surface so as not to tilt again, and also turn off the engine. This way you will avoid electric shock, which is supplied to the light bulb when the engine is on. To avoid a short circuit during operation, on most cars it would be a good idea to disconnect the negative terminal of the battery. It is always better to start replacing from the right side. The headlight unit is equipped with a plastic cover. It is dismantled using a socket and extension.

There may be some minor additional complications with this operation. The socket with a light bulb is sometimes more difficult to get due to the fact that it is quite small in size and is located in a hard-to-reach place. To remove this cartridge, find it and start rocking it up and down until the cartridge is completely removed. There is no need to rotate the chuck.

Start installation work from the side where the washer fluid reservoir is installed. Then you should move on to the headlight installed on the battery side. The cartridge on this side is more difficult to reach due to the body. While removing, use your hand to lift the part up.

The dismantling process requires the presence of a special tool. Manufacturers place a protrusion on the lamp socket. Use a flat blade screwdriver to grab onto this tab and use a lever action to remove the cartridge.

To do this, you must first prepare the car as indicated above (place it on a flat surface and turn off the engine), and then begin installation work.

1. Open the hood and disconnect the negative cable from the battery (to avoid a short circuit).
2. Remove the plugs that go to the lamps, and then remove the element into which the plug is installed.
3. Turn the light bulb clockwise 45 - 60 degrees, then remove the spare part. To remove the lamp, gently pull it towards you. The socket itself first rotates along with the light source, then it is removed.
4. Install a new light bulb and carry out the reverse dismantling.

Safety precautions

During work, try not to touch exposed wires to avoid electric shock. The light bulb to be installed should not be dirty or greasy. It is better to carry out the work with gloves. It is definitely recommended to turn off the engine. After installation, check the functionality of the light bulb.

If the light bulb does not work, then the reason is either a manufacturing defect or you did not tighten it well enough.

conclusions

All of the above actions mainly apply to commonly used car models. On some premium cars (Merscedes-Benz or Infinity), changing the light bulb yourself will be quite problematic due to the complex modern design, so you will have to use the services of a service station. But for other cars (such as the Hundai Solaris or Renault Logan), it will be much easier to replace it yourself, so as not to waste extra time and money.

When choosing, give preference to ordinary lamps. You should not buy too bright LEDs or even xenon lamps. But you shouldn’t take ordinary cheap incandescent lamps either, because their service life is shorter and there is a risk of melting and cracking.

You should also not buy cheap Chinese lamps at flea markets. It is better to take spare parts from well-known foreign manufacturers. You should not save on light bulbs installed in side lights, because traffic safety in the dark directly depends on them.