Each user needs to know what to buy a generator is not the most important thing. It is important to ensure its work. It will be able to help this special oil for a 4-use benzogenerator. Lubrication is necessary so that the unit can start and execute the stated functions. Without such a substance, the unit will not be able to fully work and will not give the right power.
When I bought the equipment, it turned out that any oil would not fit. It is necessary to use the composition that is suitable precisely for a specific generator. Only in this case, it turns out to use the device at full capacity and access all the features of the device. In general, let's talk about how to choose a suitable oil for filling into a gasoline generator.
Before buying a suitable generator, it is worth carefully examining the characteristics of the equipment and clarify which oil it may be necessary. Particular attention is recommended to pay the type of installed engine, and which type of fuel is used - gasoline or diesel fuel. This characteristic directly depends on the choice of lubrication.
The oil is designed to protrude the motor protection against the negative environmental impact. Lubrication allows you to reduce the level of wear of parts in the motor, and therefore save the working properties of the generator for a long time.
An important point is that the generators of the C4-ectant motor work on pure gasoline. The oil is poured into a special container. Consumption of such devices can be up to 1-2 liters per hour
Classification of oils - what are suitable for a benzogenerator?
The lubricating composition is an integral consumable material, without which the generator will not work. Lubrication is needed to reduce friction between individual elements. During the operation of the equipment, it is necessary that you be a sufficient lubrication level. This will reduce wear and allow you to avoid serious breakdowns. It is important that the motor will not stop. In addition, a product for a run-in is first poured into a new unit, which in 5 hours of operation should be merged. Each 20-50 hours of operation, oil is recommended to change.
Fill the first oil it is categorically not recommended. This can lead to a serious breakdown and additional costs. A knowledgeable person will be able to determine without any problems, for which a concrete oil is suitable. Focus follow marking:
- the compositions are marked through the API system and suitable for benzogenerators, have the letter "s". The second letter is a class. Low classes are A, B and C;
- lubricants with marking SJ, SL are suitable for gasoline devices, but it is important to pay attention to the product to be intended for a 4-bit motor.
The composition differ synthetics, mineral water and semi-synthetic. Different producers can be purchased with a lubricant with different additives. It is additives that define the basic properties of the product and the order of its operation. If you want to navigate the choice of SAE, then the important parameter is the temperature and individual features of the equipment operation.
What oil is poured into a benzogenerator?
The most convenient option can be the use of all-season oil. It is allowed to change mineral water on a synthetic and back, but you need to not add, but to fully change the substance to avoid conflict additives when mixing. In addition to the type of lubricant, it is worth paying attention to the performance characteristics of the product.
As an example, I will give the most popular lubricants for benzogenerators from different manufacturers:
- Super 1000. All-season product, mineral, including thickener. Universal. Cost - from 660 rubles per liter.
- Magnatec. Popular product that can be used in different motors. Synthetic, ensures reliable wear protection. Cost of liter 720 rubles.
- Q8 - a synthetic of excellent quality, obtained by hydrocracking. Allows reduced fuel consumption. Cost of liter - 940 rubles.
- Forte SAE. Semi-synthetic. Universal and all-season. Suitable for use in cold conditions. The price of liters is 480 rubles.
- Werk SAE. Budget product for 450 rubles / liter. Suitable only for gasoline generators.
- Mostela. Modern product that has very low yields. It costs - 560 rubles / liter.
Only high-quality oil can be a pledge of long and productive lubrication. Here it is necessary to remember that the engine and car engine is different aggregate. Caring for these structures varies. The owner of the generator station must clearly comply with the procedure for inspection and change all consumables on time. If you regularly change the smellar, the unit will be able to work for many years.
Skat company, having its own service centers, knows about all generator diseases. The reason for the large part of the breakdown is the wrong choice of engine oil.. Therefore, before using the equipment, let's figure out which oil is necessary for the normal operation of the gasoline generator.
Gasoline engines are divided into two-stroke and four-stroke
In the two-stroke there is no separate crankcase under the oil: The carburetor is poured the oil and gasoline mixture. Therefore, special requirements are presented to oil for push-pull engines: in addition to lubricating properties, it should be dissolved in gasoline, and also to fully burn.
There are no problems with the choice here: n pay for special oil for two-stroke engines with air-cooled - standard 2T. Do not confuse with butter with TC-W3 marking - it is for water-cooled engines (suspended boat motors, hydrocycles).
Moving to four-stroke engines. The choice is much more.
Exist two main classifications of motor oils:
by viscosity (SAE)
by sets of operational properties (API).
SAE informs about the ambient temperature in which the oil will work the highest quality, lubricating all nodes. This standard subdivides motor oils for six winter species (OW, 5W, 10W, 15W, 20W, and 25W) and five summer (20, 30, 40 and 50). A dual number means all-season oil (5W-30, 5W-40, 10W-50, etc.).
The most versatile SAE for the warm season will be oil 10W30. Therefore, seeing the SL 10W30 on the label - you can take it. When operating the generator, in the cold season, we pay attention to the marking of SJ or SL, is the most modern and high-quality oils for gasoline engines.
By sets of operational properties (API), they are once again on the margin of SJ or SL.
What else needs to be aware of oil in gasoline generators
Fully replace the oil after the first 20 hours of work ("Running") a new generator. Then do it according to the manufacturer's recommendations, usually every 50 (if mineral oil) or 100 (if the oil is synthetic) hours of operation. Change the oil is better on the warm engine.
Check the oil level before each startIf necessary, tosses to the diploma.
After starting the engine, let it warm up and dispel the oil on the system during 3-5 minutes idling.
Check the oil level every 5-6 hours (or daily).
Fully change oil 1 time per seasonEven if the generator is rarely operated.
So, do not neglect the choice of proper engine oil for the generator. Insufficient lubrication brings the generator to breakage. Choose oil for the season and constantly follow its level. These simple rules will extend the service life of the generator.
Oil is one of the most important components of any engine, without exception.
The most popular questions that set the holders of generators are associated with the choice of oil for the generator. For example: "What kind of oil to fill in a benzogenerator?," How often to change the oil in the generator? " , "What kind of oil to pour into the engine of the benzogenerator?". You can get an answer to all these questions by reading this article.
On the issue of choosing oil to the generator, it is necessary to approach with all seriousness, since the wrong choice often leads to the malfunction of the regenerator and the rapid wear of the engine.
Types of oil
To begin with, it is worth understanding which types of oil exist.
To work properly, two types of oil are used: engine oil and consistency (which for lubrication).
Motor oil is necessary for work between rotating and rubbing engine parts, the consistency is intended to maintain the operation of the sliding and rolling bearings.
Mark Oil
The product you choose plays an important role. It is worth paying due attention to the oil producer, if you prefer a quality product, not a fake, then you need to choose oil of a well-known manufacturer. The most famous brands such as: Honda, Esso, Oregon, Craftmsman, GT Oil, Briggs & Stratton and the Great Many others.
Essei you give your preference to one bridge, then it is worth sticking to it throughout the entire time, you should not change the brand too often.
It is desirable to make a purchase exclusively in large specialized stores with a decent reputation.
What if you still apply a poor-quality product?
It is necessary to rinse the engine system and pour good quality oil.
Remember!The key to the stable and durable work of your generator is high-quality oil.
Classification (marking) oils
API. - The system is designed so that, thanks to her, you have the opportunity to choose the products the corresponding type of engine and the service life.
Mark S.(first letter) - designed for oil onto a gasoline engine.
The second letter - characterizes the level of quality (the further the letter from the beginning of the alphabet is located, the quality of the oil is higher).
Today, the highest quality oil is considered to be marked with SN.
It is advisable to use motor oils that match the SL class by APIs that have the appropriate marking on the packaging.
SAE marking Indicates viscosity and oil fluidity.
You can select such SAE groups:
- Winter(0W, 5W, 10W, 15W, 20W, and 25W), where the number is at what temperature can oil, naturally with a minus sign.
- Summer (20W, 30W, 40W and 50W), this oil may be used at temperatures above zero degrees.
- Marking of universal oil - 5W-30, 5W-40, 10W-50 for operation at any temperatures.
It is important, the fact that for each engine, individually, depending on the manufacturer, power, etc. - All oil can not approach immediately. Therefore, the temperature table (indicated below) can help you in the selection.
For benzogenerators, high-quality oils for 4-stroke engines are used, which meet the requirements of automakers to maintain a class not lower than SG.
Oil viscosity
As practice shows, it is not worth pouring the synthetics. Rather, apply semi-synthetics, which has the properties of synthetic and mineral oils
So, the answer to the question ...... ..
"How often to change the oil in the generator?"
For each manufacturer, the question of changing the oil is individual. Occupatic oil is recommended to drain, and it must be necessary to occur after 30-50 hours or 6 months. It should be done, even if they write what to do this is not necessary.
It should be remembered!
Replacing the oil in the benzogenerator is not all the procedures for the maintenance of your benzogenerator.
Depending on the time of work, you need to conduct
timely procedures TO-0, TO-1, TO-2, TO-3, TO-4.
Work, which includes that:
1. Replacing the oil
2. Cleaning or replacing filters: fuel, oil and air.
3. Production of the cleaning of the fuel crane.
4. Cleaning, as well as setting the carburetor.
5. Setting the valves.
6. Replacement or cleaning of spark plug
7. Checking AKB, also checking the battery charger
9. Diagnosis of all electrical unit nodes on third-party noise.
10. Check Low Oil Protection System
11. Increased frequency and voltage.
12. The fuel tank.
13. Check and replacing the fuel hose,
14. Diagnostics and ignition adjustment
15. Check the piston group
16.Tell cleaning from dirt
Simple oil replacement does not give any guarantees, that your benzogenerator will continue to work smoothly.
If you do not meet the list of regulatory work, the generator can:
1. Practice start
2. Hurt
3. Climb
4. Spell load.
Is it necessary to replace the oil of 100% quality or need maintenance?
Our experienced specialists will be able to quickly and efficiently, with the help of special equipment and tools to spend any at affordable prices. Call by phone: 063 202-90-70 or 097 023-42-42.
|
| For the quality of the work of gasoline, many of its components are responsible. How the power plant will work, which current will be supplied and the stable will produce a voltage depends in the even extent from its mechanisms, and from the assembly, and on the quality of the materials used. And even from the manufacturer. However, there are two leading and defining elements - an alternator and engine. If the generator motor is good and works, "as a watch", then there are no problems. Today I will tell you how to care for the engine in order to achieve such a desired result - long-term work without failures and repairs. I always warn inexperienced users that a gasoline engine is not easy, it requires a lot of attention, regular inspection and maintenance. One of the most important stages of care is to replace the oil. Any gasoline 4-stroke engine cannot function normally without a certain viscosity oil, as well as in its small amount or workout. The side effect will be such a sharp increase in the normal operating temperature, the rapid erase of the compression rings, the stitch on the cylinder, which will lead to premature wear of the motor or critical breakdown. In this article, I will try to tell in detail what kind of oil to fill in, which interval, what brand and viscosity should be in the oil. |
We choose the brand of oil
To the question of pouring the oil, the best answer is high-quality. This is if you love your gene and wish him long life. After all, often the premature breakdown of the generator is written off on the manufacturer - they say, the factory marriage and the quality is bad. But in fact, you yourself are to blame - pour bad oil.
Often a conscientious manufacturer clearly indicates what to use to not harm the technique. The brand is registered in the supasport.
If there is no such information, I recommend:
- Buy only good oils of well-known manufacturers (Shell, Mobil, Liqui Moly) or oil in specialized stores that sell gardening equipment;
- Apply for the bay of purely semi-synthetic oil. Recommended marks - 10W30 and 10W40. They are ideal for almost any weather conditions;
- Under the condition of harsh winter (-30 or more) I recommend to consider the winter oil 5W30, which is also semi-synthetic;
- In marking, viscosity is indicated by numbers: 5, 10 - at low temperatures, 30-40 when heated.
How often do oil change?
Oil change has a certain interval that is registered for each generator inhis technical support, but there are cases when the documentation is not always eating or a passport can be in a foreign language. For example, the recommendation is hardly the rollerfind there. Meanwhile, it is very important for the normal vital activity of your station.
Oil Replacement Tips:
- If the product is new, the first replacement should happen after 5 hours of operation. This is the same "run-in" I spoke about. New details as it were, they are "soldered" to each other, smoothed micronether. At the same time, the oil absorbs all metalated particles, it becomes worked - black and muddy. This consistency must be drained and changed;
- The second replacement occurs (on average) - after 20-25 hours of operation. This is the optimal replacement interval, despite the way the generator coped with what loads;
- I recommend the third replacement of oil after 50 hours of operation. Subsequent replacements can be at intervals of both 50 and 100 hours - this indicator depends on the manufacturer or installed on the engine generator. I recommend clearly stick to the specified interval in the technical passport of the generator itself.
Replacement procedure
The very first step is to turn off the power plant and install it smoothly and reliably. Thenthe used oil for the gasoline generator needs to be merged, and in return to fill the fresh.
For this:
- Slightly warm up the exhaust oil by turning on the engine for 10-15 minutes. So it is easier to merge;
- Under the drain hole we substitute a bucket or other container (1-5 l);
- Bottom - plug for drain. In different oil carters it looks different. Sometimes it is a bolt that do not get out completely, but slightly weakening its fastening;
- The oil begins to flow. The process takes some time. It is necessary to wait and make sure that the entire spent oil has flowed;
- After a drain, you need to tighten the drain bolt and through the crankcase bay tube pour new oil into the tank;
- We check whether the oil level is sufficient. In the crankcase, he must be under the thread. We spin as a dense lid as possible. Replacing the oil is completed. The device can work further
In no case neglect the timely replacement of oil, because it is fraught with the failure of the engine, additional monetary costs for its restoration and time loss. Practice shows that even a person who never did it can produce independently a replacement in the shortest possible time.
Motor oil is important component of any engine. Regardless of its design, this product is simply vital in it, since it performs two key functions, lubrication and cooling. It prevents the occurrence of excessive friction between metal parts, the formation of metal chips. As a result, moving parts are not encouraged, they work properly. Also, the lubricant is involved in the cooling of the pistons - it takes it to the heat that occurs when they are moved. But not all of them are monotonous, each of them is suitable only for a particular task, more precisely, the engine and operating conditions, so it matters which oil it is worth pouring into - in different conditions will behave differently.
The choice of oil is disclosed in the video below, we recommend for viewing
To know exactly what oil is best used for a gasoline generator, you need to understand what is present. In pristine one form is raw oil. She is has good lubricant properties And quite a knitting to stay on the lubricated details. These properties were open at the end of the last century and patented in the United States. The world's first brand was called " Valvoline." But the product from ordinary oil, even performs its function, but is not quite clean for modern equipment - sulfur and paraffin create pollution and gale, which negatively affects the engine performance. Therefore, an alternative was the synthetic oil applicable to a benzogenerator, which is mined by distillation of oil and parsing it to the main components from which the basic substance is manufactured.
Various additives are added to it, thanks to which enhance its operational characteristics.Another opinion on the topic of oil selection
Classification of oils
A total of several classifications of motor oils for. Each of them in one way or another characterizes the properties and distributes them to the relevant groups. Among them are two main classifications groups, this API is in which substances are indicated for the totality of operational properties and the SAE-classification of viscosity. Both are characterized for motor oil on a gasoline engine.
API system It is designed in such a way that with its help, it was possible to choose products corresponding to the service life and type of a particular engine. For oil onto a gasoline engine, a marker S is assigned, the second letter characterizes the level of quality. Thus, the lowest level is SG, which is suitable for old engines issued until 1993. SH - for engines released in 1996, SJ - 2001, and SL - for more modern. In general, in this classification presents substances with marks that begin with the first letter of the English alphabet. The further such a letter of classification from the beginning, the higher the quality of the oil. At the moment, the highest quality product is indicated by the SN marking.
