There are many ways tuning, the cheapest of which is refining headlights. In addition to the elementary replacement of near and far light bulbs, car enthusiasts often interest how to make dimensions in turn signals. Some drivers even duplicate the overall light on the VAZ 2110 or VAZ 2114. This is done due to the not very good visibility of lighting on the road surface, which is very important at night and in bad weather to prevent accidents.
Types of jobs
Model turn signals on auto in the following ways:
- supplement the burning turn signals by dimensions, moving them from the front headlights;
- insert additional overall lamps on the front optics;
- change the color of the overall lamps on yellow or white;
- use
If the dimensions are yellow, then the light from the turn signals will merge with it, if the color is white, then against the background of the main dimensions of turn signals will stand out Installation process
Before you understand how to connect turn signals to dimensions, keep in mind that there are two main colors of optics of overall lights:
- yellow ("American") with the same color of rotary optics will merge;
- white turning yellow color is better standing out on the road.
The overall lights in the turn signals on the car are inserted as follows:
- in the rotary optics on the Vaz cut the hole where the cartridge will be inserted. It is permissible to use the type of w5w cartridge. It will be inserted into a standard incandescent light bulb by 5 W or in LED tape;
- cartridge fasten in optics for turning in order to avoid moisture, dirt and for durable mounting;
- to transfer illumination from headlights in the VAZ 2107 or 2109, switch the wires to just mounted cartridge. When connecting additional lights without transfer, the contact is required in the block that goes to the block pharmito parallel.
Auto after such a refinement acquires a special charm Despite the seeming convenience for the driver, according to the CACAP, such a change in the configuration leads to the delusion of other drivers and even becomes the cause of accidents.
Also note that when installing the lights of lighting devices equipped with red lights or reflectors, as well as devices with inappropriate legislation, the work regime and color you face a fine in such sizes:
- 2500 rubles, if you are a civilian person;
- 15,000-20000 rubles - official;
- 40000-50000 rubles - legal.
Penalties are governed by the provision of car tolerance.
Recently, motorists resort to the possibility to equip overall lighting in turns through light bulbs with two contacts. But this measure can also prevent other road users. Thus, manipulations with the headlights, which they would be useful for you, can encroach your safety. Therefore, do not be surprised to increase attention to your car from the traffic police officers.
Good time Dear readers, the other day I caught fire with my car a little American, and decided to make dimensions in the turn signals, there are not many options for such an operation, for example, such: 1) to embed the second base and put it from factory dimensions, but such a manual is not satisfied When turning on the turn signal, it burns brighter.
2)— Put the two filament light bulb (it makes it difficult to find the fact that two yellow light bulbs find it difficult to find, and besides the result is the same in the first version.
3)— The option that I chose, and the most difficult (the creation of two modes of rotary light bulbs using a 5-touch relay, diode and condenser). I will try to tell you about all your actions.
First of all, we go to the store of electric parts and buy there:
1.
Condenser for 4700 μF * 25V or 3000 μF * 25V or 3300 μF * 25V I do not know what the difference, it seems like in the container, I used 4700 ICF * 25V everything is necessary - 2pcs.
2. Diode 5817 or 5819, I also do not know what the difference, I took 5817
3. Relay 5-pin ordinary car - 2pcs
3. Terminals for relay - 2pcs
4. Round terminals - 2 pcs
5. Wire - 4m. (Colored) I took in colors as in the scheme
6. Isol or heat shrink
7. Mom's terminals
set of young electrician
Then take the scheme and begin to collect everything according to the scheme
After they did homework) we go to the car, remove both headlights and looking for "+" from the dimensions and "+" from the turn signals. In total, there are only 2 wires, color will be plus, and plus from the dimension will be in the cruise of the upper right corner of the chips. And again, focusing on the scheme begin to twist the wires.
Then connect "-" in any convenient place. That's it seems to be all.
Many want to improve the front optics, because with a good light ride much more comfortable and safer for you, if only your light did not interfere with the oncoming drivers. For this there are a lot of ways. But some wish to get a unique and unusual look at the tuning tuning. For this, for example, they are installed in turn signals additional dimensions or completely transfer them to, creating, the so-called American style.
The American style is that the dimensions are burning constantly, their light bulbs are in turn signals and most often they are orange.
American women on VAZ 2114 Very frequent practice, with them the car really looks more interesting, in addition, in the dark, any additional light will not hurt. With poor visibility, a car with such tuning is more noticeable on the road. But you need to understand that such a change can be misleading other participants in the movement and sometimes it is caused by an accident.
Yellow dimensions merge with turn signals, and some road participants may incorrectly assess the situation. Therefore, it is better to use white dimensions, then orange turn signals will be clearly highlighted. 
The attention of DPS officers to a car with such a refinement is increased, and it is possible to stop for verification of documents will be more often.
Making Americans VAZ 2114 Everything must be done within the law, there are clear limitations in any changes in the front optics. For example, it is definitely impossible to install red lamps, reflectors and any other devices with inappropriate color and mode of operation. For such violations, a fine of 2500 rubles was appointed.
How to make american on vaz 2114
There are a lot of ways to implement Americans on VAZ 2114, everyone has their pros and cons. Depending on your skills, desires and opportunities, you can choose any, from below the presented, or invent your own. 
Lamp in a turn signal with two threads.
A two-dimensional lamp is a relatively good way. It is quite easy to install and understandable to use. There are two threads in the lamp, one dull to 5 wat, a friend is brighter on 25 wat. The thread with weak brightness is used as overall lights, and with strong turn signals. As a result, the turn signal is quite clearly noticeable, on the background of overall lights.
For installation, the base is required for two +, or solder the wire directly to the lamp, but you need to be careful, while it can overcome.
Relay
The principle of signal inversion. At the same time, the turn signal lamp is constantly lit, and when the signal is turned on, it starts blinking. In brightness, as in the previous case, the lights do not differ, but the signal is distinguished due to the fact that the lamp at the time of work completely goes out.
With the installation, everything is simple, it will only take a little cut wires and two five-pin relays, one for each headlight.
Relay with condenser and diode
This method is essentially more correct previous. In5819 diode and 25 volts of 4700 mf are added to the five-contact relay. The principle of operation is the same, but there is a guarantee that nothing, will not be closed anywhere and will last long without any problems.
Circuit of dimensions on the bullet lamp
There is nothing easier how to close the turn signals on the VAZ 2114. But this method is not faithful, and it is not categorically recommended to use it. The rotate lamp is directly connected to the dimensions, and the signal of the rotation is essentially missing at all.
Extra Cartridge in the Swivel Far
The most correct in the opinion of the majority, but at the same time the most labor cost method is the introduction of an additional cartridge in the headlight. The cartridges are taken from unnecessary repeaters, cut off and fall into the headlight. With careful performance, everything looks unnoticed, not everyone guess about the changes made.
Useful video
For more information on installing dimensions in turn signals, you can get from the video below:
Manufacturing process:
Step one. Device scheme
The scheme of the system of the system is very simple, here is practically and nothing to describe. All you need to do is connect the items in a certain order to break between turning lamps and power. Meals when working in dimensions need to be served on a single wire. The author did not connect the dimensions directly with turning lights, he made a separate button to include "American women" if necessary. For these purposes, the counter of the fog buttons were involved.
Step second. Relay connection process
The relay is connected by soldering. How to do this, you can see in detail in the photo. The most important thing in this process is a thorough insulation of the place of soldering and open conductors.
Step Three. Connect the button and test the system
Now it remains to connect the system to the shoe computer block, connect the button, the author even connected the power indicator. Now after pressing the button, it begins to glow, which indicates that the system is enabled. Well, how everything works, you can see more detailed on the video.
